diff options
Diffstat (limited to 'include/configs/VoVPN-GW.h')
| -rw-r--r-- | include/configs/VoVPN-GW.h | 216 |
1 files changed, 108 insertions, 108 deletions
diff --git a/include/configs/VoVPN-GW.h b/include/configs/VoVPN-GW.h index db05d82..982f8d8 100644 --- a/include/configs/VoVPN-GW.h +++ b/include/configs/VoVPN-GW.h @@ -82,10 +82,10 @@ #define CONFIG_LOADS_ECHO 1 /* don't allow baudrate change */ -#undef CFG_LOADS_BAUD_CHANGE +#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* supported baudrates */ -#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } /* * select ethernet configuration @@ -107,32 +107,32 @@ #define CONFIG_ETHER_INDEX 1 /* Marvell Switch SMI base addr */ -#define CFG_PHY_ADDR 0x10 +#define CONFIG_SYS_PHY_ADDR 0x10 /* FCC1 RMII REFCLK is CLK10 */ -#define CFG_CMXFCR_VALUE CMXFCR_TF1CS_CLK10 -#define CFG_CMXFCR_MASK (CMXFCR_FC1|CMXFCR_TF1CS_MSK) +#define CONFIG_SYS_CMXFCR_VALUE CMXFCR_TF1CS_CLK10 +#define CONFIG_SYS_CMXFCR_MASK (CMXFCR_FC1|CMXFCR_TF1CS_MSK) /* BDs and buffers on 60x bus */ -#define CFG_CPMFCR_RAMTYPE 0 +#define CONFIG_SYS_CPMFCR_RAMTYPE 0 /* Local Protect, Full duplex, Flowcontrol, RMII */ -#define CFG_FCC_PSMR (FCC_PSMR_LPB|FCC_PSMR_FDE|\ +#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_LPB|FCC_PSMR_FDE|\ FCC_PSMR_FCE|FCC_PSMR_RMII) /* bit-bang MII PHY management */ #define CONFIG_BITBANGMII #define MDIO_PORT 1 /* Port B */ -#define CFG_MDIO_PIN 0x00002000 /* PB18 */ -#define CFG_MDC_PIN 0x00001000 /* PB19 */ -#define MDIO_ACTIVE (iop->pdir |= CFG_MDIO_PIN) -#define MDIO_TRISTATE (iop->pdir &= ~CFG_MDIO_PIN) -#define MDIO_READ ((iop->pdat & CFG_MDIO_PIN) != 0) -#define MDIO(bit) if(bit) iop->pdat |= CFG_MDIO_PIN; \ - else iop->pdat &= ~CFG_MDIO_PIN -#define MDC(bit) if(bit) iop->pdat |= CFG_MDC_PIN; \ - else iop->pdat &= ~CFG_MDC_PIN +#define CONFIG_SYS_MDIO_PIN 0x00002000 /* PB18 */ +#define CONFIG_SYS_MDC_PIN 0x00001000 /* PB19 */ +#define MDIO_ACTIVE (iop->pdir |= CONFIG_SYS_MDIO_PIN) +#define MDIO_TRISTATE (iop->pdir &= ~CONFIG_SYS_MDIO_PIN) +#define MDIO_READ ((iop->pdat & CONFIG_SYS_MDIO_PIN) != 0) +#define MDIO(bit) if(bit) iop->pdat |= CONFIG_SYS_MDIO_PIN; \ + else iop->pdat &= ~CONFIG_SYS_MDIO_PIN +#define MDC(bit) if(bit) iop->pdat |= CONFIG_SYS_MDC_PIN; \ + else iop->pdat &= ~CONFIG_SYS_MDC_PIN #define MIIDELAY udelay(1) #endif @@ -209,60 +209,60 @@ */ /* undef to save memory */ -#define CFG_LONGHELP +#define CONFIG_SYS_LONGHELP /* monitor command prompt */ -#define CFG_PROMPT "=> " +#define CONFIG_SYS_PROMPT "=> " /* console i/o buffer size */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 +#define CONFIG_SYS_CBSIZE 1024 #else -#define CFG_CBSIZE 256 +#define CONFIG_SYS_CBSIZE 256 #endif /* print buffer size */ -#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) /* max number of command args */ -#define CFG_MAXARGS 16 +#define CONFIG_SYS_MAXARGS 16 /* boot argument buffer size */ -#define CFG_BARGSIZE CFG_CBSIZE +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* memtest works on */ -#define CFG_MEMTEST_START 0x00100000 +#define CONFIG_SYS_MEMTEST_START 0x00100000 /* 1 ... 15 MB in DRAM */ -#define CFG_MEMTEST_END 0x00f00000 +#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* full featured memtest */ -#define CFG_ALT_MEMTEST +#define CONFIG_SYS_ALT_MEMTEST /* default load address */ -#define CFG_LOAD_ADDR 0x00100000 +#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* decrementer freq: 1 ms ticks */ -#define CFG_HZ 1000 +#define CONFIG_SYS_HZ 1000 /* configure flash */ -#define CFG_FLASH_BASE 0xff800000 -#define CFG_MAX_FLASH_BANKS 1 -#define CFG_MAX_FLASH_SECT 64 -#define CFG_FLASH_SIZE 8 -#undef CFG_FLASH_16BIT -#define CFG_FLASH_ERASE_TOUT 240000 -#define CFG_FLASH_WRITE_TOUT 500 -#define CFG_FLASH_LOCK_TOUT 500 -#define CFG_FLASH_UNLOCK_TOUT 10000 -#define CFG_FLASH_PROTECTION +#define CONFIG_SYS_FLASH_BASE 0xff800000 +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +#define CONFIG_SYS_MAX_FLASH_SECT 64 +#define CONFIG_SYS_FLASH_SIZE 8 +#undef CONFIG_SYS_FLASH_16BIT +#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 +#define CONFIG_SYS_FLASH_LOCK_TOUT 500 +#define CONFIG_SYS_FLASH_UNLOCK_TOUT 10000 +#define CONFIG_SYS_FLASH_PROTECTION /* monitor in flash */ -#define CFG_MONITOR_OFFSET 0x00700000 +#define CONFIG_SYS_MONITOR_OFFSET 0x00700000 /* environment in flash */ -#define CFG_ENV_IS_IN_FLASH 1 -#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00020000) -#define CFG_ENV_SIZE 0x00020000 -#define CFG_ENV_SECT_SIZE 0x00020000 +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00020000) +#define CONFIG_ENV_SIZE 0x00020000 +#define CONFIG_ENV_SECT_SIZE 0x00020000 /* * Initial memory map for linux @@ -270,52 +270,52 @@ * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* hard reset configuration words */ #ifdef CONFIG_CLKIN_66MHz -#define CFG_HRCW_MASTER 0x04643050 +#define CONFIG_SYS_HRCW_MASTER 0x04643050 #else #error NO HRCW FOR 100MHZ SPECIFIED !!! #endif -#define CFG_HRCW_SLAVE1 0x00000000 -#define CFG_HRCW_SLAVE2 0x00000000 -#define CFG_HRCW_SLAVE3 0x00000000 -#define CFG_HRCW_SLAVE4 0x00000000 -#define CFG_HRCW_SLAVE5 0x00000000 -#define CFG_HRCW_SLAVE6 0x00000000 -#define CFG_HRCW_SLAVE7 0x00000000 +#define CONFIG_SYS_HRCW_SLAVE1 0x00000000 +#define CONFIG_SYS_HRCW_SLAVE2 0x00000000 +#define CONFIG_SYS_HRCW_SLAVE3 0x00000000 +#define CONFIG_SYS_HRCW_SLAVE4 0x00000000 +#define CONFIG_SYS_HRCW_SLAVE5 0x00000000 +#define CONFIG_SYS_HRCW_SLAVE6 0x00000000 +#define CONFIG_SYS_HRCW_SLAVE7 0x00000000 /* internal memory mapped register */ -#define CFG_IMMR 0xF0000000 +#define CONFIG_SYS_IMMR 0xF0000000 /* definitions for initial stack pointer and data area (in DPRAM) */ -#define CFG_INIT_RAM_ADDR CFG_IMMR -#define CFG_INIT_RAM_END 0x2000 -#define CFG_GBL_DATA_SIZE 128 -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR +#define CONFIG_SYS_INIT_RAM_END 0x2000 +#define CONFIG_SYS_GBL_DATA_SIZE 128 +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /* * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ -#define CFG_SDRAM_BASE 0x00000000 -#define CFG_SDRAM_SIZE (32*1024*1024) -#define CFG_MONITOR_BASE TEXT_BASE -#define CFG_MONITOR_FLASH (CFG_FLASH_BASE + CFG_MONITOR_OFFSET) -#define CFG_MONITOR_LEN 0x00020000 -#define CFG_MALLOC_LEN 0x00020000 +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_SIZE (32*1024*1024) +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE +#define CONFIG_SYS_MONITOR_FLASH (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_OFFSET) +#define CONFIG_SYS_MONITOR_LEN 0x00020000 +#define CONFIG_SYS_MALLOC_LEN 0x00020000 /* boot flags */ #define BOOTFLAG_COLD 0x01 /* normal power-on */ #define BOOTFLAG_WARM 0x02 /* software reboot */ /* cache configuration */ -#define CFG_CACHELINE_SIZE 32 /* for MPC8260 */ +#define CONFIG_SYS_CACHELINE_SIZE 32 /* for MPC8260 */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of above */ +#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of above */ #endif /* @@ -328,43 +328,43 @@ * * HID1 has only read-only information - nothing to set. */ -#define CFG_HID0_INIT (HID0_ICE|HID0_DCE|\ +#define CONFIG_SYS_HID0_INIT (HID0_ICE|HID0_DCE|\ HID0_ICFI|HID0_DCI|HID0_IFEM|HID0_ABE) -#define CFG_HID0_FINAL (HID0_IFEM|HID0_ABE) -#define CFG_HID2 0 +#define CONFIG_SYS_HID0_FINAL (HID0_IFEM|HID0_ABE) +#define CONFIG_SYS_HID2 0 /* RMR - reset mode register - turn on checkstop reset enable */ -#define CFG_RMR RMR_CSRE +#define CONFIG_SYS_RMR RMR_CSRE /* BCR - bus configuration */ -#define CFG_BCR 0x00000000 +#define CONFIG_SYS_BCR 0x00000000 /* SIUMCR - siu module configuration */ -#define CFG_SIUMCR 0x4905c000 +#define CONFIG_SYS_SIUMCR 0x4905c000 /* SYPCR - system protection control */ #if defined(CONFIG_WATCHDOG) -#define CFG_SYPCR 0xffffff87 +#define CONFIG_SYS_SYPCR 0xffffff87 #else -#define CFG_SYPCR 0xffffff83 +#define CONFIG_SYS_SYPCR 0xffffff83 #endif /* TMCNTSC - time counter status and control */ /* clear interrupts XXX jse */ -/*#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR) */ -#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|\ +/*#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR) */ +#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|\ TMCNTSC_TCF|TMCNTSC_TCE) /* PISCR - periodic interrupt status and control */ /* clear interrupts XXX jse */ -/*#define CFG_PISCR (PISCR_PS) */ -#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) +/*#define CONFIG_SYS_PISCR (PISCR_PS) */ +#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) /* SCCR - system clock control */ -#define CFG_SCCR 0x000001a9 +#define CONFIG_SYS_SCCR 0x000001a9 /* RCCR - risc controller configuration */ -#define CFG_RCCR 0 +#define CONFIG_SYS_RCCR 0 /* * MEMORY MAP @@ -379,37 +379,37 @@ * x - IMMR 384KB base=0xf0000000 */ /* XXX jse 100MHz TODO */ -#define CFG_BR0_PRELIM 0xff800801 -#define CFG_OR0_PRELIM 0xff801e44 -#define CFG_BR1_PRELIM 0x00000041 -#define CFG_OR1_PRELIM 0xfe002ec0 +#define CONFIG_SYS_BR0_PRELIM 0xff800801 +#define CONFIG_SYS_OR0_PRELIM 0xff801e44 +#define CONFIG_SYS_BR1_PRELIM 0x00000041 +#define CONFIG_SYS_OR1_PRELIM 0xfe002ec0 #if 1 -#define CFG_BR2_PRELIM 0xf0101001 -#define CFG_OR2_PRELIM 0xfff00ef4 -#define CFG_BR3_PRELIM 0xf0201001 -#define CFG_OR3_PRELIM 0xfff00ef4 -#define CFG_BR4_PRELIM 0xf0301001 -#define CFG_OR4_PRELIM 0xfff00ef4 -#define CFG_BR5_PRELIM 0xf0401001 -#define CFG_OR5_PRELIM 0xfff00ef4 +#define CONFIG_SYS_BR2_PRELIM 0xf0101001 +#define CONFIG_SYS_OR2_PRELIM 0xfff00ef4 +#define CONFIG_SYS_BR3_PRELIM 0xf0201001 +#define CONFIG_SYS_OR3_PRELIM 0xfff00ef4 +#define CONFIG_SYS_BR4_PRELIM 0xf0301001 +#define CONFIG_SYS_OR4_PRELIM 0xfff00ef4 +#define CONFIG_SYS_BR5_PRELIM 0xf0401001 +#define CONFIG_SYS_OR5_PRELIM 0xfff00ef4 #else -#define CFG_BR2_PRELIM 0xf0101081 -#define CFG_OR2_PRELIM 0xfff00104 -#define CFG_BR3_PRELIM 0xf0201081 -#define CFG_OR3_PRELIM 0xfff00104 -#define CFG_BR4_PRELIM 0xf0301081 -#define CFG_OR4_PRELIM 0xfff00104 -#define CFG_BR5_PRELIM 0xf0401081 -#define CFG_OR5_PRELIM 0xfff00104 +#define CONFIG_SYS_BR2_PRELIM 0xf0101081 +#define CONFIG_SYS_OR2_PRELIM 0xfff00104 +#define CONFIG_SYS_BR3_PRELIM 0xf0201081 +#define CONFIG_SYS_OR3_PRELIM 0xfff00104 +#define CONFIG_SYS_BR4_PRELIM 0xf0301081 +#define CONFIG_SYS_OR4_PRELIM 0xfff00104 +#define CONFIG_SYS_BR5_PRELIM 0xf0401081 +#define CONFIG_SYS_OR5_PRELIM 0xfff00104 #endif -#define CFG_BR7_PRELIM 0xf0500881 -#define CFG_OR7_PRELIM 0xffff8104 -#define CFG_MPTPR 0x2700 -#define CFG_PSDMR 0x822a2452 /* optimal */ -/*#define CFG_PSDMR 0x822a48a3 */ /* relaxed */ -#define CFG_PSRT 0x1a +#define CONFIG_SYS_BR7_PRELIM 0xf0500881 +#define CONFIG_SYS_OR7_PRELIM 0xffff8104 +#define CONFIG_SYS_MPTPR 0x2700 +#define CONFIG_SYS_PSDMR 0x822a2452 /* optimal */ +/*#define CONFIG_SYS_PSDMR 0x822a48a3 */ /* relaxed */ +#define CONFIG_SYS_PSRT 0x1a /* "bad" address */ -#define CFG_RESET_ADDRESS 0x40000000 +#define CONFIG_SYS_RESET_ADDRESS 0x40000000 #endif /* __CONFIG_H */ |