diff options
Diffstat (limited to 'include/configs/VCMA9.h')
| -rw-r--r-- | include/configs/VCMA9.h | 76 |
1 files changed, 38 insertions, 38 deletions
diff --git a/include/configs/VCMA9.h b/include/configs/VCMA9.h index aeb649e..0bc2f68 100644 --- a/include/configs/VCMA9.h +++ b/include/configs/VCMA9.h @@ -76,35 +76,35 @@ #define CONFIG_CMD_BSP -#define CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " /*********************************************************** * I2C stuff: * the MPL VCMA9 is equipped with an ATMEL 24C256 EEPROM at * address 0x50 with 16bit addressing ***********************************************************/ #define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CFG_I2C_SPEED 100000 /* I2C speed */ -#define CFG_I2C_SLAVE 0x7F /* I2C slave addr */ +#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed */ +#define CONFIG_SYS_I2C_SLAVE 0x7F /* I2C slave addr */ -#define CFG_I2C_EEPROM_ADDR 0x50 -#define CFG_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 #define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ #define CONFIG_ENV_OFFSET 0x000 /* environment starts at offset 0 */ #define CONFIG_ENV_SIZE 0x800 /* 2KB should be more than enough */ -#undef CFG_I2C_EEPROM_ADDR_OVERFLOW -#define CFG_EEPROM_PAGE_WRITE_BITS 6 /* 64 bytes page write mode on 24C256 */ -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 +#undef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 bytes page write mode on 24C256 */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* * Size of malloc() pool */ /*#define CONFIG_MALLOC_SIZE (CONFIG_ENV_SIZE + 128*1024)*/ -#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ -#define CFG_MONITOR_LEN (256 * 1024) -#define CFG_MALLOC_LEN (1024 * 1024) /* BUNZIP2 needs a lot of RAM */ +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* BUNZIP2 needs a lot of RAM */ /* * Hardware drivers @@ -129,7 +129,7 @@ #define CONFIG_DOS_PARTITION 1 /* Enable needed helper functions */ -#define CFG_DEVICE_DEREGISTER /* needs device_deregister */ +#define CONFIG_SYS_DEVICE_DEREGISTER /* needs device_deregister */ /************************************************************ * RTC @@ -160,28 +160,28 @@ /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "VCMA9 # " /* Monitor Command Prompt */ -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "VCMA9 # " /* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_MEMTEST_START 0x30000000 /* memtest works on */ -#define CFG_MEMTEST_END 0x30F80000 /* 15.5 MB in DRAM */ +#define CONFIG_SYS_MEMTEST_START 0x30000000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x30F80000 /* 15.5 MB in DRAM */ -#define CFG_ALT_MEMTEST -#define CFG_LOAD_ADDR 0x30800000 /* default load address */ +#define CONFIG_SYS_ALT_MEMTEST +#define CONFIG_SYS_LOAD_ADDR 0x30800000 /* default load address */ -#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */ +#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */ /* we configure PWM Timer 4 to 1us ~ 1MHz */ -/*#define CFG_HZ 1000000 */ -#define CFG_HZ 1562500 +/*#define CONFIG_SYS_HZ 1000000 */ +#define CONFIG_SYS_HZ 1562500 /* valid baudrates */ -#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } /* support BZIP2 compression */ #define CONFIG_BZIP2 1 @@ -211,7 +211,7 @@ #define PHYS_SDRAM_1 0x30000000 /* SDRAM Bank #1 */ #define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */ -#define CFG_FLASH_BASE PHYS_FLASH_1 +#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 /*----------------------------------------------------------------------- * FLASH and environment organization @@ -222,21 +222,21 @@ #define CONFIG_AMD_LV800 1 /* uncomment this if you have a LV800 flash */ #endif -#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ #ifdef CONFIG_AMD_LV800 #define PHYS_FLASH_SIZE 0x00100000 /* 1MB */ -#define CFG_MAX_FLASH_SECT (19) /* max number of sectors on one chip */ -#define CONFIG_ENV_ADDR (CFG_FLASH_BASE + 0x0F0000) /* addr of environment */ +#define CONFIG_SYS_MAX_FLASH_SECT (19) /* max number of sectors on one chip */ +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x0F0000) /* addr of environment */ #endif #ifdef CONFIG_AMD_LV400 #define PHYS_FLASH_SIZE 0x00080000 /* 512KB */ -#define CFG_MAX_FLASH_SECT (11) /* max number of sectors on one chip */ -#define CONFIG_ENV_ADDR (CFG_FLASH_BASE + 0x070000) /* addr of environment */ +#define CONFIG_SYS_MAX_FLASH_SECT (11) /* max number of sectors on one chip */ +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x070000) /* addr of environment */ #endif /* timeout values are in ticks */ -#define CFG_FLASH_ERASE_TOUT (5*CFG_HZ) /* Timeout for Flash Erase */ -#define CFG_FLASH_WRITE_TOUT (5*CFG_HZ) /* Timeout for Flash Write */ +#define CONFIG_SYS_FLASH_ERASE_TOUT (5*CONFIG_SYS_HZ) /* Timeout for Flash Erase */ +#define CONFIG_SYS_FLASH_WRITE_TOUT (5*CONFIG_SYS_HZ) /* Timeout for Flash Write */ #if 0 #define CONFIG_ENV_IS_IN_FLASH 1 @@ -244,8 +244,8 @@ #endif -#define CFG_JFFS2_FIRST_BANK 0 -#define CFG_JFFS2_NUM_BANKS 1 +#define CONFIG_SYS_JFFS2_FIRST_BANK 0 +#define CONFIG_SYS_JFFS2_NUM_BANKS 1 #define MULTI_PURPOSE_SOCKET_ADDR 0x08000000 @@ -255,7 +255,7 @@ #if defined(CONFIG_CMD_NAND) #define CONFIG_NAND_LEGACY -#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ +#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ #define SECTORSIZE 512 #define ADDR_COLUMN 1 |