summaryrefslogtreecommitdiff
path: root/include/configs/Total5200.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs/Total5200.h')
-rw-r--r--include/configs/Total5200.h386
1 files changed, 0 insertions, 386 deletions
diff --git a/include/configs/Total5200.h b/include/configs/Total5200.h
deleted file mode 100644
index a58eeca..0000000
--- a/include/configs/Total5200.h
+++ /dev/null
@@ -1,386 +0,0 @@
-/*
- * (C) Copyright 2003-2004
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2004
- * Mark Jonas, Freescale Semiconductor, mark.jonas@freescale.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * Check valid setting of revision define.
- * Total5100 and Total5200 Rev.1 are identical except for the processor.
- */
-#if (CONFIG_TOTAL5200_REV!=1 && CONFIG_TOTAL5200_REV!=2)
-#error CONFIG_TOTAL5200_REV must be 1 or 2
-#endif
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC5200 1 /* This is a MPC5200 CPU */
-#define CONFIG_TOTAL5200 1 /* ... on Total5200 board */
-
-/*
- * Valid values for CONFIG_SYS_TEXT_BASE are:
- * 0xFFF00000 boot high (standard configuration)
- * 0xFE000000 boot low
- * 0x00100000 boot from RAM (for testing only)
- */
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE 0xFFF00000
-#endif
-
-#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
-
-#define CONFIG_HIGH_BATS 1 /* High BATs supported */
-
-/*
- * Serial console configuration
- */
-#define CONFIG_PSC_CONSOLE 3 /* console is on PSC3 */
-#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
-
-/*
- * Video console
- */
-#define CONFIG_VIDEO
-#define CONFIG_VIDEO_SED13806
-#define CONFIG_VIDEO_SED13806_16BPP
-
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VIDEO_LOGO
-/* #define CONFIG_VIDEO_BMP_LOGO */
-#define CONFIG_CONSOLE_EXTRA_INFO
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_VIDEO_SW_CURSOR
-#define CONFIG_SPLASH_SCREEN
-
-
-/*
- * PCI Mapping:
- * 0x40000000 - 0x4fffffff - PCI Memory
- * 0x50000000 - 0x50ffffff - PCI IO Space
- */
-#define CONFIG_PCI 1
-#define CONFIG_PCI_PNP 1
-#define CONFIG_PCI_SCAN_SHOW 1
-#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
-
-#define CONFIG_PCI_MEM_BUS 0x40000000
-#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
-#define CONFIG_PCI_MEM_SIZE 0x10000000
-
-#define CONFIG_PCI_IO_BUS 0x50000000
-#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
-#define CONFIG_PCI_IO_SIZE 0x01000000
-
-#define CONFIG_MII 1
-#define CONFIG_EEPRO100 1
-#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
-#define CONFIG_NS8382X 1
-
-/* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-/* USB */
-#define CONFIG_USB_OHCI
-#define CONFIG_USB_STORAGE
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_PCI
-
-#define CONFIG_CMD_BMP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_USB
-
-
-#if (CONFIG_SYS_TEXT_BASE == 0xFE000000) /* Boot low */
-# define CONFIG_SYS_LOWBOOT 1
-#endif
-
-/*
- * Autobooting
- */
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_PREBOOT \
- "setenv stdout serial;setenv stderr serial;" \
- "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "flash_nfs=run nfsargs addip;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
- "rootpath=/opt/eldk/ppc_82xx\0" \
- "bootfile=/tftpboot/MPC5200/uImage\0" \
- ""
-
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-/*
- * IPB Bus clocking configuration.
- */
-#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 or #2 */
-
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
-
-/*
- * Flash configuration
- */
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
-#if CONFIG_TOTAL5200_REV==2
-# define CONFIG_SYS_MAX_FLASH_BANKS 3 /* max num of flash banks */
-# define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_CS5_START, CONFIG_SYS_CS4_START, CONFIG_SYS_BOOTCS_START }
-#else
-# define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
-# define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_BOOTCS_START }
-#endif
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */
-
-#if CONFIG_TOTAL5200_REV==1
-# define CONFIG_SYS_FLASH_BASE 0xFE000000
-# define CONFIG_SYS_FLASH_SIZE 0x02000000
-#elif CONFIG_TOTAL5200_REV==2
-# define CONFIG_SYS_FLASH_BASE 0xFA000000
-# define CONFIG_SYS_FLASH_SIZE 0x06000000
-#endif /* CONFIG_TOTAL5200_REV */
-
-#if defined(CONFIG_SYS_LOWBOOT)
-# define CONFIG_ENV_ADDR 0xFE040000
-#else /* CONFIG_SYS_LOWBOOT */
-# define CONFIG_ENV_ADDR 0xFFF40000
-#endif /* CONFIG_SYS_LOWBOOT */
-
-/*
- * Environment settings
- */
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_SIZE 0x40000
-#define CONFIG_ENV_SECT_SIZE 0x40000
-#define CONFIG_ENV_OVERWRITE 1
-
-/*
- * Memory map
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
-#define CONFIG_SYS_MBAR 0xF0000000 /* 64 kB */
-#define CONFIG_SYS_FPGA_BASE 0xF0010000 /* 64 kB */
-#define CONFIG_SYS_CPLD_BASE 0xF0020000 /* 64 kB */
-#define CONFIG_SYS_LCD_BASE 0xF1000000 /* 4096 kB */
-
-/* Use SRAM until RAM will be available */
-#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
-#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-# define CONFIG_SYS_RAMBOOT 1
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Ethernet configuration
- */
-#define CONFIG_MPC5xxx_FEC 1
-#define CONFIG_MPC5xxx_FEC_SEVENWIRE
-/* dummy, 7-wire FEC does not have phy address */
-#define CONFIG_PHY_ADDR 0x00
-
-/*
- * GPIO configuration
- *
- * CS1: SDRAM CS1 disabled, gpio_wkup_6 enabled 0
- * Reserved 0
- * ALTs: CAN1/2 on PSC2, SPI on PSC3 00
- * CS7: Interrupt GPIO on PSC3_5 0
- * CS8: Interrupt GPIO on PSC3_4 0
- * ATA: reset default, changed in ATA driver 00
- * IR_USB_CLK: IrDA/USB 48MHz clock gen. int., pin is GPIO 0
- * IRDA: reset default, changed in IrDA driver 000
- * ETHER: reset default, changed in Ethernet driver 0000
- * PCI_DIS: reset default, changed in PCI driver 0
- * USB_SE: reset default, changed in USB driver 0
- * USB: reset default, changed in USB driver 00
- * PSC3: SPI and UART functionality without CD 1100
- * Reserved 0
- * PSC2: CAN1/2 001
- * Reserved 0
- * PSC1: reset default, changed in AC'97 driver 000
- *
- */
-#define CONFIG_SYS_GPS_PORT_CONFIG 0x00000C10
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-
-/*
- * Various low-level settings
- */
-#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
-#define CONFIG_SYS_HID0_FINAL HID0_ICE
-
-#if CONFIG_TOTAL5200_REV==1
-# define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
-# define CONFIG_SYS_BOOTCS_SIZE 0x02000000 /* 32 MB */
-# define CONFIG_SYS_BOOTCS_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */
-# define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
-# define CONFIG_SYS_CS0_SIZE 0x02000000 /* 32 MB */
-#else
-# define CONFIG_SYS_BOOTCS_START (CONFIG_SYS_CS4_START + CONFIG_SYS_CS4_SIZE)
-# define CONFIG_SYS_BOOTCS_SIZE 0x02000000 /* 32 MB */
-# define CONFIG_SYS_BOOTCS_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */
-# define CONFIG_SYS_CS4_START (CONFIG_SYS_CS5_START + CONFIG_SYS_CS5_SIZE)
-# define CONFIG_SYS_CS4_SIZE 0x02000000 /* 32 MB */
-# define CONFIG_SYS_CS4_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */
-# define CONFIG_SYS_CS5_START CONFIG_SYS_FLASH_BASE
-# define CONFIG_SYS_CS5_SIZE 0x02000000 /* 32 MB */
-# define CONFIG_SYS_CS5_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */
-#endif
-
-#define CONFIG_SYS_CS1_START CONFIG_SYS_FPGA_BASE
-#define CONFIG_SYS_CS1_SIZE 0x00010000 /* 64 kB */
-#define CONFIG_SYS_CS1_CFG 0x0019FF00 /* 25WS, MX, AL, AA, CE, AS_25, DS_32 */
-
-#define CONFIG_SYS_CS2_START CONFIG_SYS_LCD_BASE
-#define CONFIG_SYS_CS2_SIZE 0x00400000 /* 4096 kB */
-#define CONFIG_SYS_CS2_CFG 0x0032FD0C /* 50WS, MX, AL, AA, CE, AS_25, DS_16, endian swapping */
-
-#if CONFIG_TOTAL5200_REV==1
-# define CONFIG_SYS_CS3_START CONFIG_SYS_CPLD_BASE
-# define CONFIG_SYS_CS3_SIZE 0x00010000 /* 64 kB */
-# define CONFIG_SYS_CS3_CFG 0x000ADF00 /* 10WS, MX, AL, CE, AS_25, DS_32 */
-#else
-# define CONFIG_SYS_CS3_START CONFIG_SYS_CPLD_BASE
-# define CONFIG_SYS_CS3_SIZE 0x00010000 /* 64 kB */
-# define CONFIG_SYS_CS3_CFG 0x000AD800 /* 10WS, MX, AL, CE, AS_24, DS_8 */
-#endif
-
-#define CONFIG_SYS_CS_BURST 0x00000000
-#define CONFIG_SYS_CS_DEADCYCLE 0x33333333
-
-/*-----------------------------------------------------------------------
- * USB stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_USB_CLOCK 0x0001BBBB
-#define CONFIG_USB_CONFIG 0x00001000
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff Supports IDE harddisk
- *-----------------------------------------------------------------------
- */
-
-#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-
-#define CONFIG_IDE_RESET /* reset for ide supported */
-#define CONFIG_IDE_PREINIT
-
-#define CONFIG_SYS_ATA_CS_ON_I2C2
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
-
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C)
-
-/* Interval between registers */
-#define CONFIG_SYS_ATA_STRIDE 4
-
-#endif /* __CONFIG_H */