diff options
Diffstat (limited to 'include/configs/Total5200.h')
| -rw-r--r-- | include/configs/Total5200.h | 386 |
1 files changed, 0 insertions, 386 deletions
diff --git a/include/configs/Total5200.h b/include/configs/Total5200.h deleted file mode 100644 index a58eeca..0000000 --- a/include/configs/Total5200.h +++ /dev/null @@ -1,386 +0,0 @@ -/* - * (C) Copyright 2003-2004 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * (C) Copyright 2004 - * Mark Jonas, Freescale Semiconductor, mark.jonas@freescale.com. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * Check valid setting of revision define. - * Total5100 and Total5200 Rev.1 are identical except for the processor. - */ -#if (CONFIG_TOTAL5200_REV!=1 && CONFIG_TOTAL5200_REV!=2) -#error CONFIG_TOTAL5200_REV must be 1 or 2 -#endif - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC5200 1 /* This is a MPC5200 CPU */ -#define CONFIG_TOTAL5200 1 /* ... on Total5200 board */ - -/* - * Valid values for CONFIG_SYS_TEXT_BASE are: - * 0xFFF00000 boot high (standard configuration) - * 0xFE000000 boot low - * 0x00100000 boot from RAM (for testing only) - */ -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 -#endif - -#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ - -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 3 /* console is on PSC3 */ -#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -/* - * Video console - */ -#define CONFIG_VIDEO -#define CONFIG_VIDEO_SED13806 -#define CONFIG_VIDEO_SED13806_16BPP - -#define CONFIG_CFB_CONSOLE -#define CONFIG_VIDEO_LOGO -/* #define CONFIG_VIDEO_BMP_LOGO */ -#define CONFIG_CONSOLE_EXTRA_INFO -#define CONFIG_VGA_AS_SINGLE_DEVICE -#define CONFIG_VIDEO_SW_CURSOR -#define CONFIG_SPLASH_SCREEN - - -/* - * PCI Mapping: - * 0x40000000 - 0x4fffffff - PCI Memory - * 0x50000000 - 0x50ffffff - PCI IO Space - */ -#define CONFIG_PCI 1 -#define CONFIG_PCI_PNP 1 -#define CONFIG_PCI_SCAN_SHOW 1 -#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 - -#define CONFIG_PCI_MEM_BUS 0x40000000 -#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS -#define CONFIG_PCI_MEM_SIZE 0x10000000 - -#define CONFIG_PCI_IO_BUS 0x50000000 -#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS -#define CONFIG_PCI_IO_SIZE 0x01000000 - -#define CONFIG_MII 1 -#define CONFIG_EEPRO100 1 -#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ -#define CONFIG_NS8382X 1 - -/* Partitions */ -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION - -/* USB */ -#define CONFIG_USB_OHCI -#define CONFIG_USB_STORAGE - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_PCI - -#define CONFIG_CMD_BMP -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IDE -#define CONFIG_CMD_PING -#define CONFIG_CMD_USB - - -#if (CONFIG_SYS_TEXT_BASE == 0xFE000000) /* Boot low */ -# define CONFIG_SYS_LOWBOOT 1 -#endif - -/* - * Autobooting - */ -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_PREBOOT \ - "setenv stdout serial;setenv stderr serial;" \ - "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "flash_nfs=run nfsargs addip;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ - "rootpath=/opt/eldk/ppc_82xx\0" \ - "bootfile=/tftpboot/MPC5200/uImage\0" \ - "" - -#define CONFIG_BOOTCOMMAND "run flash_self" - -/* - * IPB Bus clocking configuration. - */ -#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ - -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 or #2 */ - -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70 - -/* - * Flash configuration - */ -#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ -#if CONFIG_TOTAL5200_REV==2 -# define CONFIG_SYS_MAX_FLASH_BANKS 3 /* max num of flash banks */ -# define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_CS5_START, CONFIG_SYS_CS4_START, CONFIG_SYS_BOOTCS_START } -#else -# define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ -# define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_BOOTCS_START } -#endif -#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */ - -#if CONFIG_TOTAL5200_REV==1 -# define CONFIG_SYS_FLASH_BASE 0xFE000000 -# define CONFIG_SYS_FLASH_SIZE 0x02000000 -#elif CONFIG_TOTAL5200_REV==2 -# define CONFIG_SYS_FLASH_BASE 0xFA000000 -# define CONFIG_SYS_FLASH_SIZE 0x06000000 -#endif /* CONFIG_TOTAL5200_REV */ - -#if defined(CONFIG_SYS_LOWBOOT) -# define CONFIG_ENV_ADDR 0xFE040000 -#else /* CONFIG_SYS_LOWBOOT */ -# define CONFIG_ENV_ADDR 0xFFF40000 -#endif /* CONFIG_SYS_LOWBOOT */ - -/* - * Environment settings - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x40000 -#define CONFIG_ENV_SECT_SIZE 0x40000 -#define CONFIG_ENV_OVERWRITE 1 - -/* - * Memory map - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 -#define CONFIG_SYS_MBAR 0xF0000000 /* 64 kB */ -#define CONFIG_SYS_FPGA_BASE 0xF0010000 /* 64 kB */ -#define CONFIG_SYS_CPLD_BASE 0xF0020000 /* 64 kB */ -#define CONFIG_SYS_LCD_BASE 0xF1000000 /* 4096 kB */ - -/* Use SRAM until RAM will be available */ -#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -# define CONFIG_SYS_RAMBOOT 1 -#endif - -#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Ethernet configuration - */ -#define CONFIG_MPC5xxx_FEC 1 -#define CONFIG_MPC5xxx_FEC_SEVENWIRE -/* dummy, 7-wire FEC does not have phy address */ -#define CONFIG_PHY_ADDR 0x00 - -/* - * GPIO configuration - * - * CS1: SDRAM CS1 disabled, gpio_wkup_6 enabled 0 - * Reserved 0 - * ALTs: CAN1/2 on PSC2, SPI on PSC3 00 - * CS7: Interrupt GPIO on PSC3_5 0 - * CS8: Interrupt GPIO on PSC3_4 0 - * ATA: reset default, changed in ATA driver 00 - * IR_USB_CLK: IrDA/USB 48MHz clock gen. int., pin is GPIO 0 - * IRDA: reset default, changed in IrDA driver 000 - * ETHER: reset default, changed in Ethernet driver 0000 - * PCI_DIS: reset default, changed in PCI driver 0 - * USB_SE: reset default, changed in USB driver 0 - * USB: reset default, changed in USB driver 00 - * PSC3: SPI and UART functionality without CD 1100 - * Reserved 0 - * PSC2: CAN1/2 001 - * Reserved 0 - * PSC1: reset default, changed in AC'97 driver 000 - * - */ -#define CONFIG_SYS_GPS_PORT_CONFIG 0x00000C10 - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - - -/* - * Various low-level settings - */ -#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI -#define CONFIG_SYS_HID0_FINAL HID0_ICE - -#if CONFIG_TOTAL5200_REV==1 -# define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE -# define CONFIG_SYS_BOOTCS_SIZE 0x02000000 /* 32 MB */ -# define CONFIG_SYS_BOOTCS_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */ -# define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE -# define CONFIG_SYS_CS0_SIZE 0x02000000 /* 32 MB */ -#else -# define CONFIG_SYS_BOOTCS_START (CONFIG_SYS_CS4_START + CONFIG_SYS_CS4_SIZE) -# define CONFIG_SYS_BOOTCS_SIZE 0x02000000 /* 32 MB */ -# define CONFIG_SYS_BOOTCS_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */ -# define CONFIG_SYS_CS4_START (CONFIG_SYS_CS5_START + CONFIG_SYS_CS5_SIZE) -# define CONFIG_SYS_CS4_SIZE 0x02000000 /* 32 MB */ -# define CONFIG_SYS_CS4_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */ -# define CONFIG_SYS_CS5_START CONFIG_SYS_FLASH_BASE -# define CONFIG_SYS_CS5_SIZE 0x02000000 /* 32 MB */ -# define CONFIG_SYS_CS5_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */ -#endif - -#define CONFIG_SYS_CS1_START CONFIG_SYS_FPGA_BASE -#define CONFIG_SYS_CS1_SIZE 0x00010000 /* 64 kB */ -#define CONFIG_SYS_CS1_CFG 0x0019FF00 /* 25WS, MX, AL, AA, CE, AS_25, DS_32 */ - -#define CONFIG_SYS_CS2_START CONFIG_SYS_LCD_BASE -#define CONFIG_SYS_CS2_SIZE 0x00400000 /* 4096 kB */ -#define CONFIG_SYS_CS2_CFG 0x0032FD0C /* 50WS, MX, AL, AA, CE, AS_25, DS_16, endian swapping */ - -#if CONFIG_TOTAL5200_REV==1 -# define CONFIG_SYS_CS3_START CONFIG_SYS_CPLD_BASE -# define CONFIG_SYS_CS3_SIZE 0x00010000 /* 64 kB */ -# define CONFIG_SYS_CS3_CFG 0x000ADF00 /* 10WS, MX, AL, CE, AS_25, DS_32 */ -#else -# define CONFIG_SYS_CS3_START CONFIG_SYS_CPLD_BASE -# define CONFIG_SYS_CS3_SIZE 0x00010000 /* 64 kB */ -# define CONFIG_SYS_CS3_CFG 0x000AD800 /* 10WS, MX, AL, CE, AS_24, DS_8 */ -#endif - -#define CONFIG_SYS_CS_BURST 0x00000000 -#define CONFIG_SYS_CS_DEADCYCLE 0x33333333 - -/*----------------------------------------------------------------------- - * USB stuff - *----------------------------------------------------------------------- - */ -#define CONFIG_USB_CLOCK 0x0001BBBB -#define CONFIG_USB_CONFIG 0x00001000 - -/*----------------------------------------------------------------------- - * IDE/ATA stuff Supports IDE harddisk - *----------------------------------------------------------------------- - */ - -#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ - -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ - -#define CONFIG_IDE_RESET /* reset for ide supported */ -#define CONFIG_IDE_PREINIT - -#define CONFIG_SYS_ATA_CS_ON_I2C2 -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ - -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 - -#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA - -/* Offset for data I/O */ -#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) - -/* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) - -/* Offset for alternate registers */ -#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) - -/* Interval between registers */ -#define CONFIG_SYS_ATA_STRIDE 4 - -#endif /* __CONFIG_H */ |