summaryrefslogtreecommitdiff
path: root/include/configs/TQM8260.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs/TQM8260.h')
-rw-r--r--include/configs/TQM8260.h251
1 files changed, 124 insertions, 127 deletions
diff --git a/include/configs/TQM8260.h b/include/configs/TQM8260.h
index 2d54d23..582e670 100644
--- a/include/configs/TQM8260.h
+++ b/include/configs/TQM8260.h
@@ -60,11 +60,7 @@
#define CONFIG_BOOTCOUNT_LIMIT
-#if defined(CONFIG_CONS_NONE) || defined(CONFIG_CONS_USE_EXTC)
-#define CONFIG_BAUDRATE 230400
-#else
-#define CONFIG_BAUDRATE 9600
-#endif
+#define CONFIG_BAUDRATE 115200
#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
@@ -83,18 +79,18 @@
"flash_self=run ramargs addip;" \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
- "rootpath=/opt/eldk/ppc_82xx\0" \
- "bootfile=/tftpboot/TQM8260/uImage\0" \
- "kernel_addr=40040000\0" \
- "ramdisk_addr=40100000\0" \
+ "rootpath=/opt/eldk/ppc_6xx\0" \
+ "bootfile=tqm8260/uImage\0" \
+ "kernel_addr=400C0000\0" \
+ "ramdisk_addr=40240000\0" \
""
#define CONFIG_BOOTCOMMAND "run flash_self"
/* enable I2C and select the hardware/software driver */
#undef CONFIG_HARD_I2C /* I2C with hardware support */
#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
/*
* Software (bit-bang) I2C driver configuration
@@ -126,10 +122,10 @@
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
#endif
-#define CFG_I2C_EEPROM_ADDR 0x50
-#define CFG_I2C_EEPROM_ADDR_LEN 2
-#define CFG_EEPROM_PAGE_WRITE_BITS 4
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
#define CONFIG_I2C_X
@@ -183,7 +179,7 @@
* - RX clk is CLK11
* - TX clk is CLK12
*/
-# define CFG_CMXSCR_VALUE (CMXSCR_RS1CS_CLK11 | CMXSCR_TS1CS_CLK12)
+# define CONFIG_SYS_CMXSCR_VALUE (CMXSCR_RS1CS_CLK11 | CMXSCR_TS1CS_CLK12)
#elif defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2)
@@ -193,10 +189,10 @@
* - RAM for BD/Buffers is on the 60x Bus (see 28-13)
* - Enable Full Duplex in FSMR
*/
-# define CFG_CMXFCR_MASK (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
-# define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
-# define CFG_CPMFCR_RAMTYPE 0
-# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
+# define CONFIG_SYS_CMXFCR_MASK (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
+# define CONFIG_SYS_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
+# define CONFIG_SYS_CPMFCR_RAMTYPE 0
+# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
#endif /* CONFIG_ETHER_ON_FCC, CONFIG_ETHER_INDEX */
@@ -213,7 +209,7 @@
#endif /* CONFIG_MPC8255 */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
#undef CONFIG_WATCHDOG /* watchdog disabled */
@@ -245,142 +241,143 @@
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#endif
#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-#define CFG_RESET_ADDRESS 0xFFFFFFFC /* "bad" address */
+#define CONFIG_SYS_RESET_ADDRESS 0xFFFFFFFC /* "bad" address */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/* What should the base address of the main FLASH be and how big is
* it (in MBytes)? This must contain TEXT_BASE from board/tqm8260/config.mk
* The main FLASH is whichever is connected to *CS0.
*/
-#define CFG_FLASH0_BASE 0x40000000
-#define CFG_FLASH1_BASE 0x60000000
-#define CFG_FLASH0_SIZE 32
-#define CFG_FLASH1_SIZE 32
+#define CONFIG_SYS_FLASH0_BASE 0x40000000
+#define CONFIG_SYS_FLASH1_BASE 0x60000000
+#define CONFIG_SYS_FLASH0_SIZE 32
+#define CONFIG_SYS_FLASH1_SIZE 32
/* Flash bank size (for preliminary settings)
*/
-#define CFG_FLASH_SIZE CFG_FLASH0_SIZE
+#define CONFIG_SYS_FLASH_SIZE CONFIG_SYS_FLASH0_SIZE
/*-----------------------------------------------------------------------
* FLASH organization
*/
-#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */
-#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */
-#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
+
+/* use CFI flash driver */
+#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
+#define CONFIG_SYS_FLASH_EMPTY_INFO 1
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
-#if 0
-/* Start port with environment in flash; switch to EEPROM later */
#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_ADDR (CFG_FLASH_BASE+0x40000)
-#define CONFIG_ENV_SIZE 0x40000
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x40000)
+#define CONFIG_ENV_SIZE 0x08000
#define CONFIG_ENV_SECT_SIZE 0x40000
-#else
-/* Final version: environment in EEPROM */
-#define CONFIG_ENV_IS_IN_EEPROM 1
-#define CONFIG_ENV_OFFSET 0
-#define CONFIG_ENV_SIZE 2048
-#endif
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
/*-----------------------------------------------------------------------
* Hardware Information Block
*/
-#define CFG_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
-#define CFG_HWINFO_SIZE 0x00000040 /* size of HW Info block */
-#define CFG_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */
+#define CONFIG_SYS_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
+#define CONFIG_SYS_HWINFO_SIZE 0x00000040 /* size of HW Info block */
+#define CONFIG_SYS_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */
/*-----------------------------------------------------------------------
* Hard Reset Configuration Words
*
- * if you change bits in the HRCW, you must also change the CFG_*
+ * if you change bits in the HRCW, you must also change the CONFIG_SYS_*
* defines for the various registers affected by the HRCW e.g. changing
- * HRCW_DPPCxx requires you to also change CFG_SIUMCR.
+ * HRCW_DPPCxx requires you to also change CONFIG_SYS_SIUMCR.
*/
#define __HRCW__ALL__ (HRCW_CIP | HRCW_ISB111 | HRCW_BMS)
#if defined(CONFIG_MPC8255) || defined(CONFIG_MPC8265)
-# define CFG_HRCW_MASTER (__HRCW__ALL__ | HRCW_MODCK_H0111)
+# define CONFIG_SYS_HRCW_MASTER (__HRCW__ALL__ | HRCW_MODCK_H0111)
#else /* ! MPC8255 && !MPC8265 */
# if defined(CONFIG_266MHz)
-# define CFG_HRCW_MASTER (__HRCW__ALL__ | HRCW_MODCK_H0111)
+# define CONFIG_SYS_HRCW_MASTER (__HRCW__ALL__ | HRCW_MODCK_H0111)
# elif defined(CONFIG_300MHz)
-# define CFG_HRCW_MASTER (__HRCW__ALL__ | HRCW_MODCK_H0110)
+# define CONFIG_SYS_HRCW_MASTER (__HRCW__ALL__ | HRCW_MODCK_H0110)
# else
-# define CFG_HRCW_MASTER (__HRCW__ALL__)
+# define CONFIG_SYS_HRCW_MASTER (__HRCW__ALL__)
# endif
#endif /* CONFIG_MPC8255 */
/* no slaves so just fill with zeros */
-#define CFG_HRCW_SLAVE1 0
-#define CFG_HRCW_SLAVE2 0
-#define CFG_HRCW_SLAVE3 0
-#define CFG_HRCW_SLAVE4 0
-#define CFG_HRCW_SLAVE5 0
-#define CFG_HRCW_SLAVE6 0
-#define CFG_HRCW_SLAVE7 0
+#define CONFIG_SYS_HRCW_SLAVE1 0
+#define CONFIG_SYS_HRCW_SLAVE2 0
+#define CONFIG_SYS_HRCW_SLAVE3 0
+#define CONFIG_SYS_HRCW_SLAVE4 0
+#define CONFIG_SYS_HRCW_SLAVE5 0
+#define CONFIG_SYS_HRCW_SLAVE6 0
+#define CONFIG_SYS_HRCW_SLAVE7 0
/*-----------------------------------------------------------------------
* Internal Memory Mapped Register
*/
-#define CFG_IMMR 0xFFF00000
+#define CONFIG_SYS_IMMR 0xFFF00000
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
-#define CFG_INIT_RAM_ADDR CFG_IMMR
-#define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data*/
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
+#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in DPRAM */
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data*/
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*
- * 60x SDRAM is mapped at CFG_SDRAM_BASE, local SDRAM
+ * 60x SDRAM is mapped at CONFIG_SYS_SDRAM_BASE, local SDRAM
* is mapped at SDRAM_BASE2_PRELIM.
*/
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_FLASH_BASE CFG_FLASH0_BASE
-#define CFG_MONITOR_BASE TEXT_BASE
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH0_BASE
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (512 << 10) /* Reserve 512 kB for malloc()*/
/*
* Internal Definitions
@@ -394,9 +391,9 @@
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */
#if defined(CONFIG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
@@ -409,28 +406,28 @@
*
* HID1 has only read-only information - nothing to set.
*/
-#define CFG_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\
+#define CONFIG_SYS_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\
HID0_IFEM|HID0_ABE)
-#define CFG_HID0_FINAL (HID0_IFEM|HID0_ABE)
-#define CFG_HID2 0
+#define CONFIG_SYS_HID0_FINAL (HID0_IFEM|HID0_ABE)
+#define CONFIG_SYS_HID2 0
/*-----------------------------------------------------------------------
* RMR - Reset Mode Register 5-5
*-----------------------------------------------------------------------
* turn on Checkstop Reset Enable
*/
-#define CFG_RMR RMR_CSRE
+#define CONFIG_SYS_RMR RMR_CSRE
/*-----------------------------------------------------------------------
* BCR - Bus Configuration 4-25
*-----------------------------------------------------------------------
*/
#ifdef CONFIG_BUSMODE_60x
-#define CFG_BCR (BCR_EBM|BCR_L2C|BCR_LETM|\
+#define CONFIG_SYS_BCR (BCR_EBM|BCR_L2C|BCR_LETM|\
BCR_NPQM0|BCR_NPQM1|BCR_NPQM2) /* 60x mode */
#else
#define BCR_APD01 0x10000000
-#define CFG_BCR (BCR_APD01|BCR_ETM|BCR_LETM) /* 8260 mode */
+#define CONFIG_SYS_BCR (BCR_APD01|BCR_ETM|BCR_LETM) /* 8260 mode */
#endif
/*-----------------------------------------------------------------------
@@ -438,9 +435,9 @@
*-----------------------------------------------------------------------
*/
#if 0
-#define CFG_SIUMCR (SIUMCR_DPPC10|SIUMCR_APPC10)
+#define CONFIG_SYS_SIUMCR (SIUMCR_DPPC10|SIUMCR_APPC10)
#else
-#define CFG_SIUMCR (SIUMCR_DPPC00|SIUMCR_APPC10)
+#define CONFIG_SYS_SIUMCR (SIUMCR_DPPC00|SIUMCR_APPC10)
#endif
@@ -451,10 +448,10 @@
* Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
*/
#if defined(CONFIG_WATCHDOG)
-#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
#else
-#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
SYPCR_SWRI|SYPCR_SWP)
#endif /* CONFIG_WATCHDOG */
@@ -464,7 +461,7 @@
* Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
* and enable Time Counter
*/
-#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
+#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
/*-----------------------------------------------------------------------
* PISCR - Periodic Interrupt Status and Control 4-42
@@ -472,20 +469,20 @@
* Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
* Periodic timer
*/
-#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
+#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
/*-----------------------------------------------------------------------
* SCCR - System Clock Control 9-8
*-----------------------------------------------------------------------
* Ensure DFBRG is Divide by 16
*/
-#define CFG_SCCR 0
+#define CONFIG_SYS_SCCR 0
/*-----------------------------------------------------------------------
* RCCR - RISC Controller Configuration 13-7
*-----------------------------------------------------------------------
*/
-#define CFG_RCCR 0
+#define CONFIG_SYS_RCCR 0
/*
* Init Memory Controller:
@@ -500,17 +497,17 @@
/* Initialize SDRAM on local bus
*/
-#define CFG_INIT_LOCAL_SDRAM
+#define CONFIG_SYS_INIT_LOCAL_SDRAM
#define SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */
/* Minimum mask to separate preliminary
* address ranges for CS[0:2]
*/
-#define CFG_GLOBAL_SDRAM_LIMIT (512<<20) /* less than 512 MB */
-#define CFG_LOCAL_SDRAM_LIMIT (128<<20) /* less than 128 MB */
+#define CONFIG_SYS_GLOBAL_SDRAM_LIMIT (512<<20) /* less than 512 MB */
+#define CONFIG_SYS_LOCAL_SDRAM_LIMIT (128<<20) /* less than 128 MB */
-#define CFG_MPTPR 0x4000
+#define CONFIG_SYS_MPTPR 0x4000
/*-----------------------------------------------------------------------------
* Address for Mode Register Set (MRS) command
@@ -527,17 +524,17 @@
* Settings: | 0 | 0 0 | 0 1 0 | 0 | 0 1 0 |
*-----------------------------------------------------------------------------
*/
-#define CFG_MRS_OFFS 0x00000110
+#define CONFIG_SYS_MRS_OFFS 0x00000110
/* Bank 0 - FLASH
*/
-#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\
BRx_PS_64 |\
BRx_MS_GPCM_P |\
BRx_V)
-#define CFG_OR0_PRELIM (MEG_TO_AM(CFG_FLASH_SIZE) |\
+#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) |\
ORxG_CSNT |\
ORxG_ACS_DIV1 |\
ORxG_SCY_3_CLK |\
@@ -550,25 +547,25 @@
/* Bank 1 - 60x bus SDRAM
*/
-#define CFG_PSRT 0x20
-#define CFG_LSRT 0x20
-#ifndef CFG_RAMBOOT
-#define CFG_BR1_PRELIM ((CFG_SDRAM_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_PSRT 0x20
+#define CONFIG_SYS_LSRT 0x20
+#ifndef CONFIG_SYS_RAMBOOT
+#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\
BRx_PS_64 |\
BRx_MS_SDRAM_P |\
BRx_V)
-#define CFG_OR1_PRELIM CFG_OR1_8COL
+#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR1_8COL
/* SDRAM initialization values for 8-column chips
*/
-#define CFG_OR1_8COL ((~(CFG_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
+#define CONFIG_SYS_OR1_8COL ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
ORxS_BPD_4 |\
ORxS_ROWST_PBI1_A7 |\
ORxS_NUMR_12)
-#define CFG_PSDMR_8COL (PSDMR_PBI |\
+#define CONFIG_SYS_PSDMR_8COL (PSDMR_PBI |\
PSDMR_SDAM_A15_IS_A5 |\
PSDMR_BSMA_A12_A14 |\
PSDMR_SDA10_PBI1_A8 |\
@@ -582,12 +579,12 @@
/* SDRAM initialization values for 9-column chips
*/
-#define CFG_OR1_9COL ((~(CFG_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
+#define CONFIG_SYS_OR1_9COL ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
ORxS_BPD_4 |\
ORxS_ROWST_PBI1_A5 |\
ORxS_NUMR_13)
-#define CFG_PSDMR_9COL (PSDMR_PBI |\
+#define CONFIG_SYS_PSDMR_9COL (PSDMR_PBI |\
PSDMR_SDAM_A16_IS_A5 |\
PSDMR_BSMA_A12_A14 |\
PSDMR_SDA10_PBI1_A7 |\
@@ -601,24 +598,24 @@
/* Bank 2 - Local bus SDRAM
*/
-#ifdef CFG_INIT_LOCAL_SDRAM
-#define CFG_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BRx_BA_MSK) |\
+#ifdef CONFIG_SYS_INIT_LOCAL_SDRAM
+#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BRx_BA_MSK) |\
BRx_PS_32 |\
BRx_MS_SDRAM_L |\
BRx_V)
-#define CFG_OR2_PRELIM CFG_OR2_8COL
+#define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_OR2_8COL
#define SDRAM_BASE2_PRELIM 0x80000000
/* SDRAM initialization values for 8-column chips
*/
-#define CFG_OR2_8COL ((~(CFG_LOCAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
+#define CONFIG_SYS_OR2_8COL ((~(CONFIG_SYS_LOCAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
ORxS_BPD_4 |\
ORxS_ROWST_PBI1_A8 |\
ORxS_NUMR_12)
-#define CFG_LSDMR_8COL (PSDMR_PBI |\
+#define CONFIG_SYS_LSDMR_8COL (PSDMR_PBI |\
PSDMR_SDAM_A15_IS_A5 |\
PSDMR_BSMA_A13_A15 |\
PSDMR_SDA10_PBI1_A9 |\
@@ -632,12 +629,12 @@
/* SDRAM initialization values for 9-column chips
*/
-#define CFG_OR2_9COL ((~(CFG_LOCAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
+#define CONFIG_SYS_OR2_9COL ((~(CONFIG_SYS_LOCAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
ORxS_BPD_4 |\
ORxS_ROWST_PBI1_A6 |\
ORxS_NUMR_13)
-#define CFG_LSDMR_9COL (PSDMR_PBI |\
+#define CONFIG_SYS_LSDMR_9COL (PSDMR_PBI |\
PSDMR_SDAM_A16_IS_A5 |\
PSDMR_BSMA_A13_A15 |\
PSDMR_SDA10_PBI1_A8 |\
@@ -649,8 +646,8 @@
PSDMR_WRC_2C |\
PSDMR_CL_2)
-#endif /* CFG_INIT_LOCAL_SDRAM */
+#endif /* CONFIG_SYS_INIT_LOCAL_SDRAM */
-#endif /* CFG_RAMBOOT */
+#endif /* CONFIG_SYS_RAMBOOT */
#endif /* __CONFIG_H */