diff options
Diffstat (limited to 'include/configs/QS860T.h')
| -rw-r--r-- | include/configs/QS860T.h | 390 |
1 files changed, 0 insertions, 390 deletions
diff --git a/include/configs/QS860T.h b/include/configs/QS860T.h deleted file mode 100644 index 9958c09..0000000 --- a/include/configs/QS860T.h +++ /dev/null @@ -1,390 +0,0 @@ -/* - * (C) Copyright 2003 - * MuLogic B.V. - * - * (C) Copyright 2002 - * Simple Network Magic Corporation - * - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* various debug settings */ -#undef CONFIG_SYS_DEVICE_NULLDEV /* null device */ -#undef CONFIG_SILENT_CONSOLE /* silent console */ -#undef CONFIG_SYS_CONSOLE_INFO_QUIET /* silent console ? */ -#undef DEBUG_FLASH /* debug flash code */ -#undef FLASH_DEBUG /* debug fash code */ -#undef DEBUG_ENV /* debug environment code */ - -#define CONFIG_SYS_DIRECT_FLASH_TFTP 1 /* allow direct tftp to flash */ -#define CONFIG_ENV_OVERWRITE 1 /* allow overwrite MAC address */ - - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC860 1 /* This is a MPC860 CPU */ -#define CONFIG_QS860T 1 /* ...on a QS860T module */ - -/* Start address of 512K Socketed Flash */ -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 - -#define CONFIG_FEC_ENET 1 /* FEC 10/100BaseT ethernet */ -#define CONFIG_MII -#define FEC_INTERRUPT SIU_LEVEL1 -#undef CONFIG_SCC1_ENET /* SCC1 10BaseT ethernet */ -#define CONFIG_SYS_DISCOVER_PHY - -#undef CONFIG_8xx_CONS_SMC1 -#define CONFIG_8xx_CONS_SMC2 1 /* Console is on SMC */ -#undef CONFIG_8xx_CONS_NONE - -#define CONFIG_BAUDRATE 38400 /* console baudrate = 38.4kbps */ - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -/* Pass clocks to Linux 2.4.18 in Hz */ -#undef CONFIG_CLOCKS_IN_MHZ /* clocks passsed to Linux in MHz */ - -#define CONFIG_PREBOOT "echo;" \ - "echo 'Type \\\"run flash_nfs\\\" to mount root filesystem over NFS';" \ - "echo" - -#undef CONFIG_BOOTARGS -/* TODO compare against CADM860 */ -#define CONFIG_BOOTCOMMAND "bootp; " \ - "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \ - "bootm" - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -#undef CONFIG_STATUS_LED /* Status LED disabled */ - -#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE - - -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION - -#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */ - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_IMMAP -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_NET -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DATE - - -/* TODO */ -#if 0 -/* Look at these */ -CONFIG_IPADDR -CONFIG_SERVERIP -CONFIG_I2C -CONFIG_SPI -#endif - -/* - * Environment variable storage is in NVRAM - */ -#define CONFIG_ENV_IS_IN_NVRAM 1 -#define CONFIG_ENV_SIZE 0x00001000 /* We use only the last 4K for PPCBoot */ -#define CONFIG_ENV_ADDR 0xD100E000 - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ - -#define CONFIG_SYS_HUSH_PARSER 1 /* use "hush" command parser */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -/* TODO - size? */ -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -/*----------------------------------------------------------------------- - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ -/*----------------------------------------------------------------------- - * Internal Memory Mapped Register - */ -#define CONFIG_SYS_IMMR 0xF0000000 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0xFFF00000 - -#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* TODO flash parameters */ -/*----------------------------------------------------------------------- - * FLASH organization for Intel Strataflash - */ -#define CONFIG_SYS_FLASH_16BIT 1 /* 16-bit wide flash memory */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 64 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#undef CONFIG_ENV_IS_IN_FLASH - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 11-9 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze - */ -#if defined(CONFIG_WATCHDOG) -#define CONFIG_SYS_SYPCR (0xFFFFFF88 | SYPCR_SWE | SYPCR_SWRI) -#else -#define CONFIG_SYS_SYPCR 0xFFFFFF88 -#endif - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration 11-6 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_SIUMCR 0x00620000 - -/*----------------------------------------------------------------------- - * TBSCR - Time Base Status and Control 11-26 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_TBSCR 0x00C3 - -/*----------------------------------------------------------------------- - * RTCSC - Real-Time Clock Status and Control Register 11-27 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 11-31 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_PISCR 0x0082 - -/*----------------------------------------------------------------------- - * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_PLPRCR 0x0090D000 - -/*----------------------------------------------------------------------- - * SCCR - System Clock and reset Control Register 15-27 - *----------------------------------------------------------------------- - */ -#define SCCR_MASK SCCR_EBDF11 -#define CONFIG_SYS_SCCR 0x02000000 - - -/*----------------------------------------------------------------------- - * Debug Enable Register - * 0x73E67C0F - All interrupts handled by BDM - * 0x00824001 - Only interrupts needed by MWDebug.exe handled by BDM - *----------------------------------------------------------------------- -#define CONFIG_SYS_DER 0x73E67C0F -*/ -#define CONFIG_SYS_DER 0x0082400F - - -/*----------------------------------------------------------------------- - * Memory Controller Initialization Constants - *----------------------------------------------------------------------- - */ - -/* - * BR0 and OR0 (AMD 512K Socketed FLASH) - * Base address = 0xFFF0_0000 - 0xFFF7_FFFF (After relocation) - */ -#define CONFIG_SYS_PRELIM_OR_AM -#define CONFIG_SYS_OR_TIMING_FLASH - -#define FLASH_BASE0_PRELIM 0xFFF00001 -#define CONFIG_SYS_OR0_PRELIM 0xFFF80D42 -#define CONFIG_SYS_BR0_PRELIM 0xFFF00401 - - -/* - * BR1 and OR1 (Intel 8M StrataFLASH) - * Base address = 0xD000_0000 - 0xD07F_FFFF - */ - -#define FLASH_BASE1_PRELIM 0xD0000000 -#define CONFIG_SYS_OR1_PRELIM 0xFF800D42 -#define CONFIG_SYS_BR1_PRELIM 0xD0000801 -/* #define CONFIG_SYS_OR1 0xFF800D42 */ -/* #define CONFIG_SYS_BR1 0xD0000801 */ - - -/* - * BR2 and OR2 (SDRAM) - * Base Address = 0x00000000 - 0x00FF_FFFF (16M After relocation) - * Base Address = 0x00000000 - 0x03FF_FFFF (64M After relocation) - * Base Address = 0x00000000 - 0x07FF_FFFF (128M After relocation) - * - */ -#define SDRAM_BASE 0x00000000 /* SDRAM bank */ -#define SDRAM_PRELIM_OR_AM 0xF8000000 /* map max. 128 MB */ - -/* SDRAM timing */ -#define SDRAM_TIMING 0x00000A00 - -/* For boards with 16M of SDRAM */ -#define SDRAM_16M_MAX_SIZE 0x01000000 /* max 16MB SDRAM */ -#define CONFIG_SYS_16M_MBMR 0x18802114 /* Mem Periodic Timer Prescaler */ - -/* For boards with 64M of SDRAM */ -#define SDRAM_64M_MAX_SIZE 0x04000000 /* max 64MB SDRAM */ -/* TODO - determine real value */ -#define CONFIG_SYS_64M_MBMR 0x18802114 /* Mem Period Timer Prescaler */ - -#define CONFIG_SYS_OR2 (SDRAM_PRELIM_OR_AM | SDRAM_TIMING) -#define CONFIG_SYS_BR2 (SDRAM_BASE | 0x000000C1) - - -/* - * BR3 and OR3 (NVRAM, Sipex, NAND Flash) - * Base address = 0xD100_0000 - 0xD100_FFFF (64K NVRAM) - * Base address = 0xD108_0000 - 0xD108_0000 (Sipex chip ctl register) - * Base address = 0xD110_0000 - 0xD110_0000 (NAND ctl register) - * Base address = 0xD138_0000 - 0xD138_0000 (LED ctl register) - * - */ - -#define CONFIG_SYS_OR3_PRELIM 0xFFC00DF6 -#define CONFIG_SYS_BR3_PRELIM 0xD1000401 -/* #define CONFIG_SYS_OR3 0xFFC00DF6 */ -/* #define CONFIG_SYS_BR3 0xD1000401 */ - - -/* - * BR4 and OR4 (Unused) - * Base address = 0xE000_0000 - 0xE3FF_FFFF - * - */ - -#define CONFIG_SYS_OR4_PRELIM 0xFF000000 -#define CONFIG_SYS_BR4_PRELIM 0xE0000000 -/* #define CONFIG_SYS_OR4 0xFF000000 */ -/* #define CONFIG_SYS_BR4 0xE0000000 */ - - -/* - * BR5 and OR5 (Expansion bus) - * Base address = 0xE400_0000 - 0xE7FF_FFFF - * - */ - -#define CONFIG_SYS_OR5_PRELIM 0xFF000000 -#define CONFIG_SYS_BR5_PRELIM 0xE4000000 -/* #define CONFIG_SYS_OR5 0xFF000000 */ -/* #define CONFIG_SYS_BR5 0xE4000000 */ - - -/* - * BR6 and OR6 (Expansion bus) - * Base address = 0xE800_0000 - 0xEBFF_FFFF - * - */ - -#define CONFIG_SYS_OR6_PRELIM 0xFF000000 -#define CONFIG_SYS_BR6_PRELIM 0xE8000000 -/* #define CONFIG_SYS_OR6 0xFF000000 */ -/* #define CONFIG_SYS_BR6 0xE8000000 */ - - -/* - * BR7 and OR7 (Expansion bus) - * Base address = 0xEC00_0000 - 0xEFFF_FFFF - * - */ - -#define CONFIG_SYS_OR7_PRELIM 0xFF000000 -#define CONFIG_SYS_BR7_PRELIM 0xE8000000 -/* #define CONFIG_SYS_OR7 0xFF000000 */ -/* #define CONFIG_SYS_BR7 0xE8000000 */ - -/* - * Sanity checks - */ -#if defined(CONFIG_SCC1_ENET) && defined(CONFIG_FEC_ENET) -#error Both CONFIG_SCC1_ENET and CONFIG_FEC_ENET configured -#endif - -#endif /* __CONFIG_H */ |