summaryrefslogtreecommitdiff
path: root/include/configs/PPChameleonEVB.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs/PPChameleonEVB.h')
-rw-r--r--include/configs/PPChameleonEVB.h777
1 files changed, 0 insertions, 777 deletions
diff --git a/include/configs/PPChameleonEVB.h b/include/configs/PPChameleonEVB.h
deleted file mode 100644
index e277d0d..0000000
--- a/include/configs/PPChameleonEVB.h
+++ /dev/null
@@ -1,777 +0,0 @@
-/*
- * (C) Copyright 2003-2005
- * Wolfgang Denk, DENX Software Engineering, <wd@denx.de>
- *
- * (C) Copyright 2003
- * DAVE Srl
- *
- * http://www.dave-tech.it
- * http://www.wawnet.biz
- * mailto:info@wawnet.biz
- *
- * Credits: Stefan Roese, Wolfgang Denk
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_PPCHAMELEON_MODULE_BA 0 /* Basic Model */
-#define CONFIG_PPCHAMELEON_MODULE_ME 1 /* Medium Model */
-#define CONFIG_PPCHAMELEON_MODULE_HI 2 /* High-End Model */
-#ifndef CONFIG_PPCHAMELEON_MODULE_MODEL
-#define CONFIG_PPCHAMELEON_MODULE_MODEL CONFIG_PPCHAMELEON_MODULE_BA
-#endif
-
-
-/* Only one of the following two symbols must be defined (default is 25 MHz)
- * CONFIG_PPCHAMELEON_CLK_25
- * CONFIG_PPCHAMELEON_CLK_33
- */
-#if (!defined(CONFIG_PPCHAMELEON_CLK_25) && !defined(CONFIG_PPCHAMELEON_CLK_33))
-#define CONFIG_PPCHAMELEON_CLK_25
-#endif
-
-#if (defined(CONFIG_PPCHAMELEON_CLK_25) && defined(CONFIG_PPCHAMELEON_CLK_33))
-#error "* Two external frequencies (SysClk) are defined! *"
-#endif
-
-#undef CONFIG_PPCHAMELEON_SMI712
-
-/*
- * Debug stuff
- */
-#undef __DEBUG_START_FROM_SRAM__
-#define __DISABLE_MACHINE_EXCEPTION__
-
-#ifdef __DEBUG_START_FROM_SRAM__
-#define CONFIG_SYS_DUMMY_FLASH_SIZE 1024*1024*4
-#endif
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_405EP 1 /* This is a PPC405 CPU */
-#define CONFIG_PPCHAMELEONEVB 1 /* ...on a PPChameleonEVB board */
-
-#define CONFIG_SYS_TEXT_BASE 0xFFFB0000 /* Reserve 320 kB for Monitor */
-#define CONFIG_SYS_LDSCRIPT "board/dave/PPChameleonEVB/u-boot.lds"
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
-#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
-
-
-#ifdef CONFIG_PPCHAMELEON_CLK_25
-# define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */
-#elif (defined (CONFIG_PPCHAMELEON_CLK_33))
-# define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
-#else
-# error "* External frequency (SysClk) not defined! *"
-#endif
-
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#undef CONFIG_BOOTARGS
-
-/* Ethernet stuff */
-#define CONFIG_ENV_OVERWRITE /* Let the user to change the Ethernet MAC addresses */
-#define CONFIG_ETHADDR 00:50:c2:1e:af:fe
-#define CONFIG_HAS_ETH1
-#define CONFIG_ETH1ADDR 00:50:c2:1e:af:fd
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#undef CONFIG_EXT_PHY
-
-#define CONFIG_PPC4xx_EMAC
-#define CONFIG_MII 1 /* MII PHY management */
-#ifndef CONFIG_EXT_PHY
-#define CONFIG_PHY_ADDR 1 /* EMAC0 PHY address */
-#define CONFIG_PHY1_ADDR 2 /* EMAC1 PHY address */
-#else
-#define CONFIG_PHY_ADDR 2 /* PHY address */
-#endif
-#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_SNTP
-
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#define CONFIG_RTC_M41T11 1 /* uses a M41T00 RTC */
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-#define CONFIG_SYS_M41T11_BASE_YEAR 1900
-
-/*
- * SDRAM configuration (please see cpu/ppc/sdram.[ch])
- */
-#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
-
-/* SDRAM timings used in datasheet */
-#define CONFIG_SYS_SDRAM_CL 2
-#define CONFIG_SYS_SDRAM_tRP 20
-#define CONFIG_SYS_SDRAM_tRC 65
-#define CONFIG_SYS_SDRAM_tRCD 20
-#undef CONFIG_SYS_SDRAM_tRFC
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-
-#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */
-
-#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_CONS_INDEX 1 /* Use UART0 */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_serial_clock()
-
-#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */
-#define CONFIG_SYS_BASE_BAUD 691200
-
-/* The following table includes the supported baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE \
- { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
- 57600, 115200, 230400, 460800, 921600 }
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-
-/*-----------------------------------------------------------------------
- * NAND-FLASH stuff
- *-----------------------------------------------------------------------
- */
-
-/*
- * nand device 1 on dave (PPChameleonEVB) needs more time,
- * so we just introduce additional wait in nand_wait(),
- * effectively for both devices.
- */
-#define PPCHAMELON_NAND_TIMER_HACK
-
-#define CONFIG_SYS_NAND0_BASE 0xFF400000
-#define CONFIG_SYS_NAND1_BASE 0xFF000000
-#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND0_BASE, CONFIG_SYS_NAND1_BASE }
-#define NAND_BIG_DELAY_US 25
-#define CONFIG_SYS_MAX_NAND_DEVICE 2 /* Max number of NAND devices */
-
-#define CONFIG_SYS_NAND0_CE (0x80000000 >> 1) /* our CE is GPIO1 */
-#define CONFIG_SYS_NAND0_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
-#define CONFIG_SYS_NAND0_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
-#define CONFIG_SYS_NAND0_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
-
-#define CONFIG_SYS_NAND1_CE (0x80000000 >> 14) /* our CE is GPIO14 */
-#define CONFIG_SYS_NAND1_RDY (0x80000000 >> 31) /* our RDY is GPIO31 */
-#define CONFIG_SYS_NAND1_CLE (0x80000000 >> 15) /* our CLE is GPIO15 */
-#define CONFIG_SYS_NAND1_ALE (0x80000000 >> 16) /* our ALE is GPIO16 */
-
-#define MACRO_NAND_DISABLE_CE(nandptr) do \
-{ \
- switch((unsigned long)nandptr) \
- { \
- case CONFIG_SYS_NAND0_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND0_CE); \
- break; \
- case CONFIG_SYS_NAND1_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND1_CE); \
- break; \
- } \
-} while(0)
-
-#define MACRO_NAND_ENABLE_CE(nandptr) do \
-{ \
- switch((unsigned long)nandptr) \
- { \
- case CONFIG_SYS_NAND0_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND0_CE); \
- break; \
- case CONFIG_SYS_NAND1_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND1_CE); \
- break; \
- } \
-} while(0)
-
-#define MACRO_NAND_CTL_CLRALE(nandptr) do \
-{ \
- switch((unsigned long)nandptr) \
- { \
- case CONFIG_SYS_NAND0_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND0_ALE); \
- break; \
- case CONFIG_SYS_NAND1_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND1_ALE); \
- break; \
- } \
-} while(0)
-
-#define MACRO_NAND_CTL_SETALE(nandptr) do \
-{ \
- switch((unsigned long)nandptr) \
- { \
- case CONFIG_SYS_NAND0_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND0_ALE); \
- break; \
- case CONFIG_SYS_NAND1_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND1_ALE); \
- break; \
- } \
-} while(0)
-
-#define MACRO_NAND_CTL_CLRCLE(nandptr) do \
-{ \
- switch((unsigned long)nandptr) \
- { \
- case CONFIG_SYS_NAND0_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND0_CLE); \
- break; \
- case CONFIG_SYS_NAND1_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND1_CLE); \
- break; \
- } \
-} while(0)
-
-#define MACRO_NAND_CTL_SETCLE(nandptr) do { \
- switch((unsigned long)nandptr) { \
- case CONFIG_SYS_NAND0_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND0_CLE); \
- break; \
- case CONFIG_SYS_NAND1_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND1_CLE); \
- break; \
- } \
-} while(0)
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
-#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
-#undef CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
-
-#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* PCI Vendor ID: IBM */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: --- */
-#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-
-#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CONFIG_SYS_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
-#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-
-/* Reserve 256 kB for Monitor */
-/*
-#define CONFIG_SYS_FLASH_BASE 0xFFFC0000
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
-*/
-
-/* Reserve 320 kB for Monitor */
-#define CONFIG_SYS_FLASH_BASE 0xFFFB0000
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MONITOR_LEN (320 * 1024)
-
-#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */
-
-#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
-#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
-#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
-/*
- * The following defines are added for buggy IOP480 byte interface.
- * All other boards should use the standard values (CPCI405 etc.)
- */
-#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */
-#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */
-#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-
-/*-----------------------------------------------------------------------
- * Environment Variable setup
- */
-#ifdef ENVIRONMENT_IN_EEPROM
-
-#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CONFIG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */
-#define CONFIG_ENV_SIZE 0x700 /* 2048-256 bytes may be used for env vars (total size of a CAT24WC16 is 2048 bytes)*/
-
-#else /* DEFAULT: environment in flash, using redundand flash sectors */
-
-#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
-#define CONFIG_ENV_ADDR 0xFFFF8000 /* environment starts at the first small sector */
-#define CONFIG_ENV_SECT_SIZE 0x2000 /* 8196 bytes may be used for env vars*/
-#define CONFIG_ENV_ADDR_REDUND 0xFFFFA000
-#define CONFIG_ENV_SIZE_REDUND 0x2000
-
-#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */
-
-#endif /* ENVIRONMENT_IN_EEPROM */
-
-
-#define CONFIG_SYS_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */
-#define CONFIG_SYS_NVRAM_SIZE 242 /* NVRAM size */
-
-/*-----------------------------------------------------------------------
- * I2C EEPROM (CAT24WC16) for environment
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_PPC4XX
-#define CONFIG_SYS_I2C_PPC4XX_CH0
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
-#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
-/*#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07*/
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
- /* 16 byte page write mode using*/
- /* last 4 bits of the address */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM 0xFFC00000 /* FLASH bank #0 */
-
-/*-----------------------------------------------------------------------
- * External Bus Controller (EBC) Setup
- */
-
-/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
-#define CONFIG_SYS_EBC_PB0AP 0x92015480
-#define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 1 (External SRAM) initialization */
-/* Since this must replace NOR Flash, we use the same settings for CS0 */
-#define CONFIG_SYS_EBC_PB1AP 0x92015480
-#define CONFIG_SYS_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=8bit */
-
-/* Memory Bank 2 (Flash Bank 1, NAND-FLASH) initialization */
-#define CONFIG_SYS_EBC_PB2AP 0x92015480
-#define CONFIG_SYS_EBC_PB2CR 0xFF458000 /* BAS=0xFF4,BS=4MB,BU=R/W,BW=8bit */
-
-/* Memory Bank 3 (Flash Bank 2, NAND-FLASH) initialization */
-#define CONFIG_SYS_EBC_PB3AP 0x92015480
-#define CONFIG_SYS_EBC_PB3CR 0xFF058000 /* BAS=0xFF0,BS=4MB,BU=R/W,BW=8bit */
-
-#ifdef CONFIG_PPCHAMELEON_SMI712
-/*
- * Video console (graphic: SMI LynxEM)
- */
-#define CONFIG_VIDEO
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VIDEO_SMI_LYNXEM
-#define CONFIG_VIDEO_LOGO
-/*#define CONFIG_VIDEO_BMP_LOGO*/
-#define CONFIG_CONSOLE_EXTRA_INFO
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-/* This is the base address (on 405EP-side) used to generate I/O accesses on PCI bus */
-#define CONFIG_SYS_ISA_IO 0xE8000000
-/* see also drivers/video/videomodes.c */
-#define CONFIG_SYS_DEFAULT_VIDEO_MODE 0x303
-#endif
-
-/*-----------------------------------------------------------------------
- * FPGA stuff
- */
-/* FPGA internal regs */
-#define CONFIG_SYS_FPGA_MODE 0x00
-#define CONFIG_SYS_FPGA_STATUS 0x02
-#define CONFIG_SYS_FPGA_TS 0x04
-#define CONFIG_SYS_FPGA_TS_LOW 0x06
-#define CONFIG_SYS_FPGA_TS_CAP0 0x10
-#define CONFIG_SYS_FPGA_TS_CAP0_LOW 0x12
-#define CONFIG_SYS_FPGA_TS_CAP1 0x14
-#define CONFIG_SYS_FPGA_TS_CAP1_LOW 0x16
-#define CONFIG_SYS_FPGA_TS_CAP2 0x18
-#define CONFIG_SYS_FPGA_TS_CAP2_LOW 0x1a
-#define CONFIG_SYS_FPGA_TS_CAP3 0x1c
-#define CONFIG_SYS_FPGA_TS_CAP3_LOW 0x1e
-
-/* FPGA Mode Reg */
-#define CONFIG_SYS_FPGA_MODE_CF_RESET 0x0001
-#define CONFIG_SYS_FPGA_MODE_TS_IRQ_ENABLE 0x0100
-#define CONFIG_SYS_FPGA_MODE_TS_IRQ_CLEAR 0x1000
-#define CONFIG_SYS_FPGA_MODE_TS_CLEAR 0x2000
-
-/* FPGA Status Reg */
-#define CONFIG_SYS_FPGA_STATUS_DIP0 0x0001
-#define CONFIG_SYS_FPGA_STATUS_DIP1 0x0002
-#define CONFIG_SYS_FPGA_STATUS_DIP2 0x0004
-#define CONFIG_SYS_FPGA_STATUS_FLASH 0x0008
-#define CONFIG_SYS_FPGA_STATUS_TS_IRQ 0x1000
-
-#define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
-#define CONFIG_SYS_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/
-
-/* FPGA program pin configuration */
-#define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
-#define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
-#define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
-#define CONFIG_SYS_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
-#define CONFIG_SYS_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in data cache)
- */
-/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CONFIG_SYS_TEMP_STACK_OCM 1
-
-/* On Chip Memory location */
-#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
-#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */
-#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Definitions for GPIO setup (PPC405EP specific)
- *
- * GPIO0[0] - External Bus Controller BLAST output
- * GPIO0[1-9] - Instruction trace outputs -> GPIO
- * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
- * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
- * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
- * GPIO0[24-27] - UART0 control signal inputs/outputs
- * GPIO0[28-29] - UART1 data signal input/output
- * GPIO0[30] - EMAC0 input
- * GPIO0[31] - EMAC1 reject packet as output
- */
-#define CONFIG_SYS_GPIO0_OSRL 0x40000550
-#define CONFIG_SYS_GPIO0_OSRH 0x00000110
-#define CONFIG_SYS_GPIO0_ISR1L 0x00000000
-/*#define CONFIG_SYS_GPIO0_ISR1H 0x15555445*/
-#define CONFIG_SYS_GPIO0_ISR1H 0x15555444
-#define CONFIG_SYS_GPIO0_TSRL 0x00000000
-#define CONFIG_SYS_GPIO0_TSRH 0x00000000
-#define CONFIG_SYS_GPIO0_TCR 0xF7FF8014
-
-#define CONFIG_NO_SERIAL_EEPROM
-
-/*--------------------------------------------------------------------*/
-
-#ifdef CONFIG_NO_SERIAL_EEPROM
-
-/*
-!-----------------------------------------------------------------------
-! Defines for entry options.
-! Note: Because the 405EP SDRAM controller does not support ECC, ECC DIMMs that
-! are plugged in the board will be utilized as non-ECC DIMMs.
-!-----------------------------------------------------------------------
-*/
-#undef AUTO_MEMORY_CONFIG
-#define DIMM_READ_ADDR 0xAB
-#define DIMM_WRITE_ADDR 0xAA
-
-/* Defines for CPC0_PLLMR1 Register fields */
-#define PLL_ACTIVE 0x80000000
-#define CPC0_PLLMR1_SSCS 0x80000000
-#define PLL_RESET 0x40000000
-#define CPC0_PLLMR1_PLLR 0x40000000
- /* Feedback multiplier */
-#define PLL_FBKDIV 0x00F00000
-#define CPC0_PLLMR1_FBDV 0x00F00000
-#define PLL_FBKDIV_16 0x00000000
-#define PLL_FBKDIV_1 0x00100000
-#define PLL_FBKDIV_2 0x00200000
-#define PLL_FBKDIV_3 0x00300000
-#define PLL_FBKDIV_4 0x00400000
-#define PLL_FBKDIV_5 0x00500000
-#define PLL_FBKDIV_6 0x00600000
-#define PLL_FBKDIV_7 0x00700000
-#define PLL_FBKDIV_8 0x00800000
-#define PLL_FBKDIV_9 0x00900000
-#define PLL_FBKDIV_10 0x00A00000
-#define PLL_FBKDIV_11 0x00B00000
-#define PLL_FBKDIV_12 0x00C00000
-#define PLL_FBKDIV_13 0x00D00000
-#define PLL_FBKDIV_14 0x00E00000
-#define PLL_FBKDIV_15 0x00F00000
- /* Forward A divisor */
-#define PLL_FWDDIVA 0x00070000
-#define CPC0_PLLMR1_FWDVA 0x00070000
-#define PLL_FWDDIVA_8 0x00000000
-#define PLL_FWDDIVA_7 0x00010000
-#define PLL_FWDDIVA_6 0x00020000
-#define PLL_FWDDIVA_5 0x00030000
-#define PLL_FWDDIVA_4 0x00040000
-#define PLL_FWDDIVA_3 0x00050000
-#define PLL_FWDDIVA_2 0x00060000
-#define PLL_FWDDIVA_1 0x00070000
- /* Forward B divisor */
-#define PLL_FWDDIVB 0x00007000
-#define CPC0_PLLMR1_FWDVB 0x00007000
-#define PLL_FWDDIVB_8 0x00000000
-#define PLL_FWDDIVB_7 0x00001000
-#define PLL_FWDDIVB_6 0x00002000
-#define PLL_FWDDIVB_5 0x00003000
-#define PLL_FWDDIVB_4 0x00004000
-#define PLL_FWDDIVB_3 0x00005000
-#define PLL_FWDDIVB_2 0x00006000
-#define PLL_FWDDIVB_1 0x00007000
- /* PLL tune bits */
-#define PLL_TUNE_MASK 0x000003FF
-#define PLL_TUNE_2_M_3 0x00000133 /* 2 <= M <= 3 */
-#define PLL_TUNE_4_M_6 0x00000134 /* 3 < M <= 6 */
-#define PLL_TUNE_7_M_10 0x00000138 /* 6 < M <= 10 */
-#define PLL_TUNE_11_M_14 0x0000013C /* 10 < M <= 14 */
-#define PLL_TUNE_15_M_40 0x0000023E /* 14 < M <= 40 */
-#define PLL_TUNE_VCO_LOW 0x00000000 /* 500MHz <= VCO <= 800MHz */
-#define PLL_TUNE_VCO_HI 0x00000080 /* 800MHz < VCO <= 1000MHz */
-
-/* Defines for CPC0_PLLMR0 Register fields */
- /* CPU divisor */
-#define PLL_CPUDIV 0x00300000
-#define CPC0_PLLMR0_CCDV 0x00300000
-#define PLL_CPUDIV_1 0x00000000
-#define PLL_CPUDIV_2 0x00100000
-#define PLL_CPUDIV_3 0x00200000
-#define PLL_CPUDIV_4 0x00300000
- /* PLB divisor */
-#define PLL_PLBDIV 0x00030000
-#define CPC0_PLLMR0_CBDV 0x00030000
-#define PLL_PLBDIV_1 0x00000000
-#define PLL_PLBDIV_2 0x00010000
-#define PLL_PLBDIV_3 0x00020000
-#define PLL_PLBDIV_4 0x00030000
- /* OPB divisor */
-#define PLL_OPBDIV 0x00003000
-#define CPC0_PLLMR0_OPDV 0x00003000
-#define PLL_OPBDIV_1 0x00000000
-#define PLL_OPBDIV_2 0x00001000
-#define PLL_OPBDIV_3 0x00002000
-#define PLL_OPBDIV_4 0x00003000
- /* EBC divisor */
-#define PLL_EXTBUSDIV 0x00000300
-#define CPC0_PLLMR0_EPDV 0x00000300
-#define PLL_EXTBUSDIV_2 0x00000000
-#define PLL_EXTBUSDIV_3 0x00000100
-#define PLL_EXTBUSDIV_4 0x00000200
-#define PLL_EXTBUSDIV_5 0x00000300
- /* MAL divisor */
-#define PLL_MALDIV 0x00000030
-#define CPC0_PLLMR0_MPDV 0x00000030
-#define PLL_MALDIV_1 0x00000000
-#define PLL_MALDIV_2 0x00000010
-#define PLL_MALDIV_3 0x00000020
-#define PLL_MALDIV_4 0x00000030
- /* PCI divisor */
-#define PLL_PCIDIV 0x00000003
-#define CPC0_PLLMR0_PPFD 0x00000003
-#define PLL_PCIDIV_1 0x00000000
-#define PLL_PCIDIV_2 0x00000001
-#define PLL_PCIDIV_3 0x00000002
-#define PLL_PCIDIV_4 0x00000003
-
-#ifdef CONFIG_PPCHAMELEON_CLK_25
-/* CPU - PLB/SDRAM - EBC - OPB - PCI (assuming a 25.0 MHz input clock to the 405EP) */
-#define PPCHAMELEON_PLLMR0_133_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \
- PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \
- PLL_MALDIV_1 | PLL_PCIDIV_4)
-#define PPCHAMELEON_PLLMR1_133_133_33_66_33 (PLL_FBKDIV_8 | \
- PLL_FWDDIVA_6 | PLL_FWDDIVB_4 | \
- PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
-
-#define PPCHAMELEON_PLLMR0_200_100_50_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \
- PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \
- PLL_MALDIV_1 | PLL_PCIDIV_4)
-#define PPCHAMELEON_PLLMR1_200_100_50_33 (PLL_FBKDIV_8 | \
- PLL_FWDDIVA_4 | PLL_FWDDIVB_4 | \
- PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
-
-#define PPCHAMELEON_PLLMR0_266_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \
- PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \
- PLL_MALDIV_1 | PLL_PCIDIV_4)
-#define PPCHAMELEON_PLLMR1_266_133_33_66_33 (PLL_FBKDIV_8 | \
- PLL_FWDDIVA_3 | PLL_FWDDIVB_4 | \
- PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
-
-#define PPCHAMELEON_PLLMR0_333_111_37_55_55 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \
- PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \
- PLL_MALDIV_1 | PLL_PCIDIV_2)
-#define PPCHAMELEON_PLLMR1_333_111_37_55_55 (PLL_FBKDIV_10 | \
- PLL_FWDDIVA_3 | PLL_FWDDIVB_4 | \
- PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI)
-
-#elif (defined (CONFIG_PPCHAMELEON_CLK_33))
-
-/* CPU - PLB/SDRAM - EBC - OPB - PCI (assuming a 33.3MHz input clock to the 405EP) */
-#define PPCHAMELEON_PLLMR0_133_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \
- PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \
- PLL_MALDIV_1 | PLL_PCIDIV_4)
-#define PPCHAMELEON_PLLMR1_133_133_33_66_33 (PLL_FBKDIV_4 | \
- PLL_FWDDIVA_6 | PLL_FWDDIVB_6 | \
- PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
-
-#define PPCHAMELEON_PLLMR0_200_100_50_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \
- PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \
- PLL_MALDIV_1 | PLL_PCIDIV_4)
-#define PPCHAMELEON_PLLMR1_200_100_50_33 (PLL_FBKDIV_6 | \
- PLL_FWDDIVA_4 | PLL_FWDDIVB_4 | \
- PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
-
-#define PPCHAMELEON_PLLMR0_266_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \
- PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \
- PLL_MALDIV_1 | PLL_PCIDIV_4)
-#define PPCHAMELEON_PLLMR1_266_133_33_66_33 (PLL_FBKDIV_8 | \
- PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \
- PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
-
-#define PPCHAMELEON_PLLMR0_333_111_37_55_55 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \
- PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \
- PLL_MALDIV_1 | PLL_PCIDIV_2)
-#define PPCHAMELEON_PLLMR1_333_111_37_55_55 (PLL_FBKDIV_10 | \
- PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \
- PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI)
-
-#else
-#error "* External frequency (SysClk) not defined! *"
-#endif
-
-#if (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_HI)
-/* Model HI */
-#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_333_111_37_55_55
-#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_333_111_37_55_55
-#define CONFIG_SYS_OPB_FREQ 55555555
-/* Model ME */
-#elif (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_ME)
-#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_266_133_33_66_33
-#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_266_133_33_66_33
-#define CONFIG_SYS_OPB_FREQ 66666666
-#else
-/* Model BA (default) */
-#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_133_133_33_66_33
-#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_133_133_33_66_33
-#define CONFIG_SYS_OPB_FREQ 66666666
-#endif
-
-#endif /* CONFIG_NO_SERIAL_EEPROM */
-
-#define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */
-#define NAND_CACHE_PAGES 16 /* size of nand cache in 512 bytes pages */
-
-/*
- * JFFS2 partitions
- */
-
-/* No command line, one static partition */
-#undef CONFIG_CMD_MTDPARTS
-#define CONFIG_JFFS2_DEV "nand0"
-#define CONFIG_JFFS2_PART_SIZE 0x00400000
-#define CONFIG_JFFS2_PART_OFFSET 0x00000000
-
-/* mtdparts command line support */
-/*
-#define CONFIG_CMD_MTDPARTS
-#define MTDIDS_DEFAULT "nor0=PPChameleon-0,nand0=ppchameleonevb-nand"
-*/
-
-/* 256 kB U-boot image */
-/*
-#define MTDPARTS_DEFAULT "mtdparts=PPChameleon-0:1m(kernel1),1m(kernel2)," \
- "1792k(user),256k(u-boot);" \
- "ppchameleonevb-nand:-(nand)"
-*/
-
-/* 320 kB U-boot image */
-/*
-#define MTDPARTS_DEFAULT "mtdparts=PPChameleon-0:1m(kernel1),1m(kernel2)," \
- "1728k(user),320k(u-boot);" \
- "ppchameleonevb-nand:-(nand)"
-*/
-
-#endif /* __CONFIG_H */