diff options
Diffstat (limited to 'include/configs/PMC440.h')
| -rw-r--r-- | include/configs/PMC440.h | 335 |
1 files changed, 175 insertions, 160 deletions
diff --git a/include/configs/PMC440.h b/include/configs/PMC440.h index 467a11c..fc48bc1 100644 --- a/include/configs/PMC440.h +++ b/include/configs/PMC440.h @@ -1,5 +1,5 @@ /* - * (C) Copyright 2007 + * (C) Copyright 2007-2008 * Matthias Fuchs, esd gmbh, matthias.fuchs@esd-electronics.com. * Based on the sequoia configuration file. * @@ -46,59 +46,61 @@ #endif #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ +#define CONFIG_MISC_INIT_F 1 #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ #define CONFIG_BOARD_TYPES 1 /* support board types */ /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ -#define CFG_MALLOC_LEN (1024 * 1024) /* Reserve 256 kB for malloc() */ +#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserve 256 kB for malloc() */ #define CONFIG_PRAM 0 /* use pram variable to overwrite */ -#define CFG_BOOT_BASE_ADDR 0xf0000000 -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ -#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */ -#define CFG_MONITOR_BASE TEXT_BASE -#define CFG_NAND_ADDR 0xd0000000 /* NAND Flash */ -#define CFG_OCM_BASE 0xe0010000 /* ocm */ -#define CFG_OCM_DATA_ADDR CFG_OCM_BASE -#define CFG_PCI_BASE 0xe0000000 /* Internal PCI regs */ -#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */ -#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 -#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000 -#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000 -#define CFG_PCI_MEMSIZE 0x80000000 /* 2GB! */ +#define CONFIG_SYS_BOOT_BASE_ADDR 0xf0000000 +#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */ +#define CONFIG_SYS_FLASH_BASE 0xfc000000 /* start of FLASH */ +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE +#define CONFIG_SYS_NAND_ADDR 0xd0000000 /* NAND Flash */ +#define CONFIG_SYS_OCM_BASE 0xe0010000 /* ocm */ +#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_OCM_BASE +#define CONFIG_SYS_PCI_BASE 0xe0000000 /* Internal PCI regs */ +#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ +#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000 +#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000 +#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000 +#define CONFIG_SYS_PCI_MEMSIZE 0x80000000 /* 2GB! */ /* Don't change either of these */ -#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals */ +#define CONFIG_SYS_PERIPHERAL_BASE 0xef600000 /* internal peripherals */ -#define CFG_USB2D0_BASE 0xe0000100 -#define CFG_USB_DEVICE 0xe0000000 -#define CFG_USB_HOST 0xe0000400 -#define CFG_FPGA_BASE0 0xef000000 /* 32 bit */ -#define CFG_FPGA_BASE1 0xef100000 /* 16 bit */ +#define CONFIG_SYS_USB2D0_BASE 0xe0000100 +#define CONFIG_SYS_USB_DEVICE 0xe0000000 +#define CONFIG_SYS_USB_HOST 0xe0000400 +#define CONFIG_SYS_FPGA_BASE0 0xef000000 /* 32 bit */ +#define CONFIG_SYS_FPGA_BASE1 0xef100000 /* 16 bit */ +#define CONFIG_SYS_RESET_BASE 0xef200000 /*----------------------------------------------------------------------- * Initial RAM & stack pointer *----------------------------------------------------------------------*/ /* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */ -#define CFG_INIT_RAM_ADDR CFG_OCM_BASE /* OCM */ -#define CFG_INIT_RAM_END (4 << 10) -#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE /* OCM */ +#define CONFIG_SYS_INIT_RAM_END (4 << 10) +#define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_POST_WORD_ADDR /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ -#undef CFG_EXT_SERIAL_CLOCK +#undef CONFIG_SYS_EXT_SERIAL_CLOCK #define CONFIG_BAUDRATE 115200 #define CONFIG_SERIAL_MULTI 1 #undef CONFIG_UART1_CONSOLE /* console on front panel */ -#define CFG_BAUDRATE_TABLE \ +#define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} /*----------------------------------------------------------------------- @@ -119,27 +121,27 @@ /*----------------------------------------------------------------------- * FLASH related *----------------------------------------------------------------------*/ -#define CFG_FLASH_CFI /* The flash is CFI compatible */ +#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ #define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ -#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } -#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ -#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ -#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -#define CFG_FLASH_PROTECTION 1 /* use hardware flash protection */ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ +#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware flash protection */ -#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ +#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ #ifdef CONFIG_ENV_IS_IN_FLASH #define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ -#define CONFIG_ENV_ADDR ((-CFG_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ +#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ /* Address and size of Redundant Environment Sector */ #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) @@ -170,34 +172,34 @@ * the NAND controller. sr - 2006-08-25 */ #if defined (CONFIG_NAND_U_BOOT) -#define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */ -#define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */ -#define CFG_NAND_BOOT_SPL_DST (CFG_OCM_BASE + (12 << 10)) /* Copy SPL here */ -#define CFG_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */ -#define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start NUB from this addr */ -#define CFG_NAND_BOOT_SPL_DELTA (CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST) +#define CONFIG_SYS_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */ +#define CONFIG_SYS_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */ +#define CONFIG_SYS_NAND_BOOT_SPL_DST (CONFIG_SYS_OCM_BASE + (12 << 10)) /* Copy SPL here */ +#define CONFIG_SYS_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */ +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST /* Start NUB from this addr */ +#define CONFIG_SYS_NAND_BOOT_SPL_DELTA (CONFIG_SYS_NAND_BOOT_SPL_SRC - CONFIG_SYS_NAND_BOOT_SPL_DST) /* * Define the partitioning of the NAND chip (only RAM U-Boot is needed here) */ -#define CFG_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */ -#define CFG_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */ +#define CONFIG_SYS_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */ +#define CONFIG_SYS_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */ /* * Now the NAND chip has to be defined (no autodetection used!) */ -#define CFG_NAND_PAGE_SIZE 512 /* NAND chip page size */ -#define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */ -#define CFG_NAND_PAGE_COUNT 32 /* NAND chip page count */ -#define CFG_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */ -#undef CFG_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */ - -#define CFG_NAND_ECCSIZE 256 -#define CFG_NAND_ECCBYTES 3 -#define CFG_NAND_ECCSTEPS (CFG_NAND_PAGE_SIZE / CFG_NAND_ECCSIZE) -#define CFG_NAND_OOBSIZE 16 -#define CFG_NAND_ECCTOTAL (CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS) -#define CFG_NAND_ECCPOS {0, 1, 2, 3, 6, 7} +#define CONFIG_SYS_NAND_PAGE_SIZE 512 /* NAND chip page size */ +#define CONFIG_SYS_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */ +#define CONFIG_SYS_NAND_PAGE_COUNT 32 /* NAND chip page count */ +#define CONFIG_SYS_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */ +#undef CONFIG_SYS_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */ + +#define CONFIG_SYS_NAND_ECCSIZE 256 +#define CONFIG_SYS_NAND_ECCBYTES 3 +#define CONFIG_SYS_NAND_ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / CONFIG_SYS_NAND_ECCSIZE) +#define CONFIG_SYS_NAND_OOBSIZE 16 +#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * CONFIG_SYS_NAND_ECCSTEPS) +#define CONFIG_SYS_NAND_ECCPOS {0, 1, 2, 3, 6, 7} #endif #ifdef CONFIG_ENV_IS_IN_NAND @@ -205,41 +207,42 @@ * For NAND booting the environment is embedded in the U-Boot image. Please take * look at the file board/amcc/sequoia/u-boot-nand.lds for details. */ -#define CONFIG_ENV_SIZE CFG_NAND_BLOCK_SIZE -#define CONFIG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE) +#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE +#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE) #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) #endif /*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------*/ -#define CFG_MBYTES_SDRAM (256) /* 256MB */ +#define CONFIG_SYS_MBYTES_SDRAM (256) /* 256MB */ #if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) #define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */ #endif +#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */ + /* 440EPx errata CHIP 11 */ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F #define CONFIG_I2C_CMD_TREE 1 #define CONFIG_I2C_MULTI_BUS 1 -#define CFG_I2C_MULTI_EEPROMS +#define CONFIG_SYS_I2C_MULTI_EEPROMS -#define CFG_I2C_EEPROM_ADDR 0x54 -#define CFG_I2C_EEPROM_ADDR_LEN 2 -#define CFG_EEPROM_PAGE_WRITE_ENABLE -#define CFG_EEPROM_PAGE_WRITE_BITS 5 -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 -#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x01 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 +#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x01 -#define CFG_EEPROM_WREN 1 -#define CFG_I2C_BOOT_EEPROM_ADDR 0x52 +#define CONFIG_SYS_EEPROM_WREN 1 +#define CONFIG_SYS_I2C_BOOT_EEPROM_ADDR 0x52 /* * standard dtt sensor configuration - bottom bit will determine local or @@ -259,47 +262,60 @@ * - remote temp sensor enabled, min set to 0 deg, max set to 70 deg */ #define CONFIG_DTT_ADM1021 -#define CFG_DTT_ADM1021 { { 0x4c, 0x02, 0, 1, 70, 0, 1, 70, 0} } +#define CONFIG_SYS_DTT_ADM1021 { { 0x4c, 0x02, 0, 1, 70, 0, 1, 70, 0} } -#define CONFIG_PREBOOT /* enable preboot variable */ +#define CONFIG_PREBOOT "echo Add \\\"run fpga\\\" and " \ + "\\\"painit\\\" to preboot command" #undef CONFIG_BOOTARGS /* Setup some board specific values for the default environment variables */ #define CONFIG_HOSTNAME pmc440 -#define CFG_BOOTFILE "bootfile=/tftpboot/pmc440/uImage\0" -#define CFG_ROOTPATH "rootpath=/opt/eldk_410/ppc_4xx\0" +#define CONFIG_SYS_BOOTFILE "bootfile=/tftpboot/pmc440/uImage\0" +#define CONFIG_SYS_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0" #define CONFIG_EXTRA_ENV_SETTINGS \ - CFG_BOOTFILE \ - CFG_ROOTPATH \ + CONFIG_SYS_BOOTFILE \ + CONFIG_SYS_ROOTPATH \ + "fdt_file=/tftpboot/pmc440/pmc440.dtb\0" \ "netdev=eth0\0" \ "ethrotate=no\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=${serverip}:${rootpath}\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "kernel_addr=FC000000\0" \ - "ramdisk_addr=FC180000\0" \ + "addmisc=setenv bootargs ${bootargs} mem=${mem}\0" \ + "nandargs=setenv bootargs root=/dev/mtdblock6 rootfstype=jffs2 rw\0" \ + "nand_boot=run nandargs addip addtty addmisc;bootm ${kernel_addr}\0" \ + "nand_boot_fdt=run nandargs addip addtty addmisc;" \ + "bootm ${kernel_addr} - ${fdt_addr}\0" \ + "net_nfs=tftp ${kernel_addr_r} ${bootfile};" \ + "run nfsargs addip addtty addmisc;" \ + "bootm\0" \ + "net_nfs_fdt=tftp ${kernel_addr_r} ${bootfile};" \ + "tftp ${fdt_addr_r} ${fdt_file};" \ + "run nfsargs addip addtty addmisc;" \ + "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ + "kernel_addr=ffc00000\0" \ + "kernel_addr_r=200000\0" \ + "fpga_addr=fff00000\0" \ + "fdt_addr=fff80000\0" \ + "fdt_addr_r=800000\0" \ + "fpga=fpga loadb 0 ${fpga_addr}\0" \ "load=tftp 200000 /tftpboot/pmc440/u-boot.bin\0" \ - "update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;" \ - "cp.b 200000 FFFA0000 60000\0" \ + "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \ + "cp.b 200000 fffa0000 60000\0" \ "" #define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_PPC4xx_EMAC #define CONFIG_IBM_EMAC4_V4 1 #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ @@ -307,7 +323,7 @@ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ #define CONFIG_HAS_ETH0 -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ +#define CONFIG_SYS_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ #define CONFIG_NET_MULTI 1 #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ @@ -317,13 +333,13 @@ /* USB */ #define CONFIG_USB_OHCI_NEW #define CONFIG_USB_STORAGE -#define CFG_OHCI_BE_CONTROLLER +#define CONFIG_SYS_OHCI_BE_CONTROLLER -#define CFG_USB_OHCI_BOARD_INIT 1 -#define CFG_USB_OHCI_CPU_INIT 1 -#define CFG_USB_OHCI_REGS_BASE CFG_USB_HOST -#define CFG_USB_OHCI_SLOT_NAME "ppc440" -#define CFG_USB_OHCI_MAX_ROOT_PORTS 15 +#define CONFIG_SYS_USB_OHCI_BOARD_INIT 1 +#define CONFIG_SYS_USB_OHCI_CPU_INIT 1 +#define CONFIG_SYS_USB_OHCI_REGS_BASE CONFIG_SYS_USB_HOST +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ppc440" +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 /* Comment this out to enable USB 1.1 device */ #define USB_2_0_DEVICE @@ -357,50 +373,44 @@ #define CONFIG_CMD_SDRAM /* POST support */ -#define CONFIG_POST (CFG_POST_MEMORY | \ - CFG_POST_CPU | \ - CFG_POST_UART | \ - CFG_POST_I2C | \ - CFG_POST_CACHE | \ - CFG_POST_FPU | \ - CFG_POST_ETHER | \ - CFG_POST_SPR) - -#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) - -/* esd expects pram at end of physical memory. - * So no logbuffer at the moment. - */ -#if 0 +#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ + CONFIG_SYS_POST_CPU | \ + CONFIG_SYS_POST_UART | \ + CONFIG_SYS_POST_I2C | \ + CONFIG_SYS_POST_CACHE | \ + CONFIG_SYS_POST_FPU | \ + CONFIG_SYS_POST_ETHER | \ + CONFIG_SYS_POST_SPR) + +#define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 0x4) #define CONFIG_LOGBUFFER -#endif -#define CFG_POST_CACHE_ADDR 0x10000000 /* free virtual address */ +#define CONFIG_SYS_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */ -#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ +#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ #define CONFIG_SUPPORT_VFAT /*----------------------------------------------------------------------- * Miscellaneous configurable options *----------------------------------------------------------------------*/ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ #define CONFIG_LOOPW 1 /* enable loopw command */ @@ -420,27 +430,27 @@ /* General PCI */ #define CONFIG_PCI /* include pci support */ #define CONFIG_PCI_PNP /* do (not) pci plug-and-play */ -#define CFG_PCI_CACHE_LINE_SIZE 0 /* to avoid problems with PNP */ +#define CONFIG_SYS_PCI_CACHE_LINE_SIZE 0 /* to avoid problems with PNP */ #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */ +#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */ /* Board-specific PCI */ -#define CFG_PCI_TARGET_INIT -#define CFG_PCI_MASTER_INIT +#define CONFIG_SYS_PCI_TARGET_INIT +#define CONFIG_SYS_PCI_MASTER_INIT /* PCI identification */ -#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ -#define CFG_PCI_SUBSYS_ID_NONMONARCH 0x0441 /* PCI Device ID: Non-Monarch */ -#define CFG_PCI_SUBSYS_ID_MONARCH 0x0440 /* PCI Device ID: Monarch */ -#define CFG_PCI_CLASSCODE_NONMONARCH PCI_CLASS_PROCESSOR_POWERPC -#define CFG_PCI_CLASSCODE_MONARCH PCI_CLASS_BRIDGE_HOST +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ +#define CONFIG_SYS_PCI_SUBSYS_ID_NONMONARCH 0x0441 /* PCI Device ID: Non-Monarch */ +#define CONFIG_SYS_PCI_SUBSYS_ID_MONARCH 0x0440 /* PCI Device ID: Monarch */ +#define CONFIG_SYS_PCI_CLASSCODE_NONMONARCH PCI_CLASS_PROCESSOR_POWERPC +#define CONFIG_SYS_PCI_CLASSCODE_MONARCH PCI_CLASS_BRIDGE_HOST /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FPGA stuff @@ -459,42 +469,45 @@ * On Sequoia CS0 and CS3 are switched when configuring for NAND booting */ #if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) -#define CFG_NAND_CS 2 /* NAND chip connected to CSx */ +#define CONFIG_SYS_NAND_CS 2 /* NAND chip connected to CSx */ /* Memory Bank 0 (NOR-FLASH) initialization */ -#define CFG_EBC_PB0AP 0x03017200 -#define CFG_EBC_PB0CR (CFG_FLASH_BASE | 0xda000) +#define CONFIG_SYS_EBC_PB0AP 0x03017200 +#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH_BASE | 0xda000) /* Memory Bank 2 (NAND-FLASH) initialization */ -#define CFG_EBC_PB2AP 0x018003c0 -#define CFG_EBC_PB2CR (CFG_NAND_ADDR | 0x1c000) +#define CONFIG_SYS_EBC_PB2AP 0x018003c0 +#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_NAND_ADDR | 0x1c000) #else -#define CFG_NAND_CS 0 /* NAND chip connected to CSx */ +#define CONFIG_SYS_NAND_CS 0 /* NAND chip connected to CSx */ /* Memory Bank 2 (NOR-FLASH) initialization */ -#define CFG_EBC_PB2AP 0x03017200 -#define CFG_EBC_PB2CR (CFG_FLASH_BASE | 0xda000) +#define CONFIG_SYS_EBC_PB2AP 0x03017200 +#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_FLASH_BASE | 0xda000) /* Memory Bank 0 (NAND-FLASH) initialization */ -#define CFG_EBC_PB0AP 0x018003c0 -#define CFG_EBC_PB0CR (CFG_NAND_ADDR | 0x1c000) +#define CONFIG_SYS_EBC_PB0AP 0x018003c0 +#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_NAND_ADDR | 0x1c000) #endif +/* Memory Bank 1 (RESET) initialization */ +#define CONFIG_SYS_EBC_PB1AP 0x7f817200 /* 0x03017200 */ +#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_RESET_BASE | 0x1c000) + /* Memory Bank 4 (FPGA / 32Bit) initialization */ -#define CFG_EBC_PB4AP 0x03840f40 /* BME=0,TWT=7,CSN=1,TH=7,RE=1,SOR=0,BEM=1 */ -#define CFG_EBC_PB4CR (CFG_FPGA_BASE0 | 0x1c000) /* BS=1M,BU=R/W,BW=32bit */ +#define CONFIG_SYS_EBC_PB4AP 0x03840f40 /* BME=0,TWT=7,CSN=1,TH=7,RE=1,SOR=0,BEM=1 */ +#define CONFIG_SYS_EBC_PB4CR (CONFIG_SYS_FPGA_BASE0 | 0x1c000) /* BS=1M,BU=R/W,BW=32bit */ /* Memory Bank 5 (FPGA / 16Bit) initialization */ -#define CFG_EBC_PB5AP 0x03840f40 /* BME=0,TWT=3,CSN=1,TH=0,RE=1,SOR=0,BEM=1 */ -#define CFG_EBC_PB5CR (CFG_FPGA_BASE1 | 0x1a000) /* BS=1M,BU=R/W,BW=16bit */ +#define CONFIG_SYS_EBC_PB5AP 0x03840f40 /* BME=0,TWT=3,CSN=1,TH=0,RE=1,SOR=0,BEM=1 */ +#define CONFIG_SYS_EBC_PB5CR (CONFIG_SYS_FPGA_BASE1 | 0x1a000) /* BS=1M,BU=R/W,BW=16bit */ /*----------------------------------------------------------------------- * NAND FLASH *----------------------------------------------------------------------*/ -#define CFG_MAX_NAND_DEVICE 1 -#define NAND_MAX_CHIPS 1 -#define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS) -#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ -#define CFG_NAND_QUIET_TEST 1 +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_ADDR + CONFIG_SYS_NAND_CS) +#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ +#define CONFIG_SYS_NAND_QUIET_TEST 1 /* * Internal Definitions @@ -513,4 +526,6 @@ #define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_API 1 + #endif /* __CONFIG_H */ |