diff options
Diffstat (limited to 'include/configs/PMC440.h')
| -rw-r--r-- | include/configs/PMC440.h | 75 |
1 files changed, 0 insertions, 75 deletions
diff --git a/include/configs/PMC440.h b/include/configs/PMC440.h index fd39109..c5e2f16 100644 --- a/include/configs/PMC440.h +++ b/include/configs/PMC440.h @@ -95,12 +95,7 @@ /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ -#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) #define CONFIG_ENV_IS_IN_EEPROM 1 /* use FLASH for environment vars */ -#else -#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */ -#define CONFIG_ENV_IS_EMBEDDED 1 /* use embedded environment */ -#endif /*----------------------------------------------------------------------- * RTC @@ -142,69 +137,10 @@ #define CONFIG_ENV_SIZE 0x1000 /* 4096 bytes may be used for env vars */ #endif -/* - * IPL (Initial Program Loader, integrated inside CPU) - * Will load first 4k from NAND (SPL) into cache and execute it from there. - * - * SPL (Secondary Program Loader) - * Will load special U-Boot version (NUB) from NAND and execute it. This SPL - * has to fit into 4kByte. It sets up the CPU and configures the SDRAM - * controller and the NAND controller so that the special U-Boot image can be - * loaded from NAND to SDRAM. - * - * NUB (NAND U-Boot) - * This NAND U-Boot (NUB) is a special U-Boot version which can be started - * from RAM. Therefore it mustn't (re-)configure the SDRAM controller. - * - * On 440EPx the SPL is copied to SDRAM before the NAND controller is - * set up. While still running from cache, I experienced problems accessing - * the NAND controller. sr - 2006-08-25 - */ -#if defined (CONFIG_NAND_U_BOOT) -#define CONFIG_SYS_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */ -#define CONFIG_SYS_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */ -#define CONFIG_SYS_NAND_BOOT_SPL_DST (CONFIG_SYS_OCM_BASE + (12 << 10)) /* Copy SPL here */ -#define CONFIG_SYS_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */ -#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST /* Start NUB from this addr */ -#define CONFIG_SYS_NAND_BOOT_SPL_DELTA (CONFIG_SYS_NAND_BOOT_SPL_SRC - CONFIG_SYS_NAND_BOOT_SPL_DST) - -/* - * Define the partitioning of the NAND chip (only RAM U-Boot is needed here) - */ -#define CONFIG_SYS_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */ -#define CONFIG_SYS_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */ - -/* - * Now the NAND chip has to be defined (no autodetection used!) - */ -#define CONFIG_SYS_NAND_PAGE_SIZE 512 /* NAND chip page size */ -#define CONFIG_SYS_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */ -#define CONFIG_SYS_NAND_PAGE_COUNT 32 /* NAND chip page count */ -#define CONFIG_SYS_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */ -#undef CONFIG_SYS_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */ - -#define CONFIG_SYS_NAND_ECCSIZE 256 -#define CONFIG_SYS_NAND_ECCBYTES 3 -#define CONFIG_SYS_NAND_OOBSIZE 16 -#define CONFIG_SYS_NAND_ECCPOS {0, 1, 2, 3, 6, 7} -#endif - -#ifdef CONFIG_ENV_IS_IN_NAND -/* - * For NAND booting the environment is embedded in the U-Boot image. Please take - * look at the file board/amcc/sequoia/u-boot-nand.lds for details. - */ -#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE -#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE) -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) -#endif - /*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------*/ -#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) #define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */ -#endif #define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */ /* 440EPx errata CHIP 11 */ @@ -448,7 +384,6 @@ /* * On Sequoia CS0 and CS3 are switched when configuring for NAND booting */ -#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) #define CONFIG_SYS_NAND_CS 2 /* NAND chip connected to CSx */ /* Memory Bank 0 (NOR-FLASH) initialization */ @@ -458,16 +393,6 @@ /* Memory Bank 2 (NAND-FLASH) initialization */ #define CONFIG_SYS_EBC_PB2AP 0x018003c0 #define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_NAND_ADDR | 0x1c000) -#else -#define CONFIG_SYS_NAND_CS 0 /* NAND chip connected to CSx */ -/* Memory Bank 2 (NOR-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB2AP 0x03017200 -#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_FLASH_BASE | 0xda000) - -/* Memory Bank 0 (NAND-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB0AP 0x018003c0 -#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_NAND_ADDR | 0x1c000) -#endif /* Memory Bank 1 (RESET) initialization */ #define CONFIG_SYS_EBC_PB1AP 0x7f817200 /* 0x03017200 */ |