diff options
Diffstat (limited to 'include/configs/PM828.h')
| -rw-r--r-- | include/configs/PM828.h | 220 |
1 files changed, 110 insertions, 110 deletions
diff --git a/include/configs/PM828.h b/include/configs/PM828.h index f437d21..96c86f7 100644 --- a/include/configs/PM828.h +++ b/include/configs/PM828.h @@ -28,7 +28,7 @@ #ifndef __CONFIG_H #define __CONFIG_H -#undef CFG_RAMBOOT +#undef CONFIG_SYS_RAMBOOT /* * High Level Configuration Options @@ -55,8 +55,8 @@ /* enable I2C and select the hardware/software driver */ #undef CONFIG_HARD_I2C #define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ -# define CFG_I2C_SPEED 50000 -# define CFG_I2C_SLAVE 0xFE +# define CONFIG_SYS_I2C_SPEED 50000 +# define CONFIG_SYS_I2C_SLAVE 0xFE /* * Software (bit-bang) I2C driver configuration */ @@ -72,7 +72,7 @@ #define CONFIG_RTC_PCF8563 -#define CFG_I2C_RTC_ADDR 0x51 +#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* * select serial console configuration @@ -117,25 +117,25 @@ * - Tx-CLK is CLK10 */ #define CONFIG_ETHER_ON_FCC1 -# define CFG_CMXFCR_MASK1 (CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK) +# define CONFIG_SYS_CMXFCR_MASK1 (CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK) #ifndef CONFIG_DB_CR826_J30x_ON -# define CFG_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK10) +# define CONFIG_SYS_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK10) #else -# define CFG_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK12) +# define CONFIG_SYS_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK12) #endif /* * - Rx-CLK is CLK15 * - Tx-CLK is CLK14 */ #define CONFIG_ETHER_ON_FCC2 -# define CFG_CMXFCR_MASK2 (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK) -# define CFG_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14) +# define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK) +# define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14) /* * - RAM for BD/Buffers is on the 60x Bus (see 28-13) * - Enable Full Duplex in FSMR */ -# define CFG_CPMFCR_RAMTYPE 0 -# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) +# define CONFIG_SYS_CPMFCR_RAMTYPE 0 +# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) /* system clock rate (CLKIN) - equal to the 60x and local bus speed */ #define CONFIG_8260_CLKIN 100000000 /* in Hz */ @@ -147,7 +147,7 @@ #endif #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ +#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ #undef CONFIG_WATCHDOG /* watchdog disabled */ @@ -185,82 +185,82 @@ */ #define CONFIG_NAND_LEGACY -#define CFG_DOC_SHORT_TIMEOUT -#define CFG_MAX_DOC_DEVICE 1 /* Max number of DOC devices */ +#define CONFIG_SYS_DOC_SHORT_TIMEOUT +#define CONFIG_SYS_MAX_DOC_DEVICE 1 /* Max number of DOC devices */ -#define CFG_DOC_SUPPORT_2000 -#define CFG_DOC_SUPPORT_MILLENNIUM +#define CONFIG_SYS_DOC_SUPPORT_2000 +#define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ -#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ -#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } -#define CFG_RESET_ADDRESS 0xFDFFFFFC /* "bad" address */ +#define CONFIG_SYS_RESET_ADDRESS 0xFDFFFFFC /* "bad" address */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * Flash and Boot ROM mapping */ -#define CFG_BOOTROM_BASE 0xFF800000 -#define CFG_BOOTROM_SIZE 0x00080000 -#define CFG_FLASH0_BASE 0x40000000 -#define CFG_FLASH0_SIZE 0x02000000 -#define CFG_DOC_BASE 0xFF800000 -#define CFG_DOC_SIZE 0x00100000 +#define CONFIG_SYS_BOOTROM_BASE 0xFF800000 +#define CONFIG_SYS_BOOTROM_SIZE 0x00080000 +#define CONFIG_SYS_FLASH0_BASE 0x40000000 +#define CONFIG_SYS_FLASH0_SIZE 0x02000000 +#define CONFIG_SYS_DOC_BASE 0xFF800000 +#define CONFIG_SYS_DOC_SIZE 0x00100000 /* Flash bank size (for preliminary settings) */ -#define CFG_FLASH_SIZE CFG_FLASH0_SIZE +#define CONFIG_SYS_FLASH_SIZE CONFIG_SYS_FLASH0_SIZE /*----------------------------------------------------------------------- * FLASH organization */ -#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */ -#define CFG_MAX_FLASH_SECT 135 /* max num of sects on one chip */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 135 /* max num of sects on one chip */ -#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ #if 0 /* Start port with environment in flash; switch to EEPROM later */ #define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR (CFG_FLASH_BASE+0x40000) +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE+0x40000) #define CONFIG_ENV_SIZE 0x40000 #define CONFIG_ENV_SECT_SIZE 0x40000 #else /* Final version: environment in EEPROM */ #define CONFIG_ENV_IS_IN_EEPROM 1 -#define CFG_I2C_EEPROM_ADDR 0x58 -#define CFG_I2C_EEPROM_ADDR_LEN 1 -#define CFG_EEPROM_PAGE_WRITE_BITS 4 -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x58 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ #define CONFIG_ENV_OFFSET 512 #define CONFIG_ENV_SIZE (2048 - 512) #endif @@ -268,61 +268,61 @@ /*----------------------------------------------------------------------- * Hard Reset Configuration Words * - * if you change bits in the HRCW, you must also change the CFG_* + * if you change bits in the HRCW, you must also change the CONFIG_SYS_* * defines for the various registers affected by the HRCW e.g. changing - * HRCW_DPPCxx requires you to also change CFG_SIUMCR. + * HRCW_DPPCxx requires you to also change CONFIG_SYS_SIUMCR. */ #if defined(CONFIG_BOOT_ROM) -#define CFG_HRCW_MASTER (HRCW_BPS01 | HRCW_CIP | HRCW_ISB100 | HRCW_BMS) +#define CONFIG_SYS_HRCW_MASTER (HRCW_BPS01 | HRCW_CIP | HRCW_ISB100 | HRCW_BMS) #else -#define CFG_HRCW_MASTER (HRCW_CIP | HRCW_ISB100 | HRCW_BMS) +#define CONFIG_SYS_HRCW_MASTER (HRCW_CIP | HRCW_ISB100 | HRCW_BMS) #endif /* no slaves so just fill with zeros */ -#define CFG_HRCW_SLAVE1 0 -#define CFG_HRCW_SLAVE2 0 -#define CFG_HRCW_SLAVE3 0 -#define CFG_HRCW_SLAVE4 0 -#define CFG_HRCW_SLAVE5 0 -#define CFG_HRCW_SLAVE6 0 -#define CFG_HRCW_SLAVE7 0 +#define CONFIG_SYS_HRCW_SLAVE1 0 +#define CONFIG_SYS_HRCW_SLAVE2 0 +#define CONFIG_SYS_HRCW_SLAVE3 0 +#define CONFIG_SYS_HRCW_SLAVE4 0 +#define CONFIG_SYS_HRCW_SLAVE5 0 +#define CONFIG_SYS_HRCW_SLAVE6 0 +#define CONFIG_SYS_HRCW_SLAVE7 0 /*----------------------------------------------------------------------- * Internal Memory Mapped Register */ -#define CFG_IMMR 0xF0000000 +#define CONFIG_SYS_IMMR 0xF0000000 /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in DPRAM) */ -#define CFG_INIT_RAM_ADDR CFG_IMMR -#define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */ -#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data*/ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR +#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in DPRAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data*/ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 * - * 60x SDRAM is mapped at CFG_SDRAM_BASE, local SDRAM + * 60x SDRAM is mapped at CONFIG_SYS_SDRAM_BASE, local SDRAM * is mapped at SDRAM_BASE2_PRELIM. */ -#define CFG_SDRAM_BASE 0x00000000 -#define CFG_FLASH_BASE CFG_FLASH0_BASE -#define CFG_MONITOR_BASE TEXT_BASE -#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH0_BASE +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE +#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/ -#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) -# define CFG_RAMBOOT +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +# define CONFIG_SYS_RAMBOOT #endif #ifdef CONFIG_PCI #define CONFIG_PCI_PNP #define CONFIG_EEPRO100 -#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ +#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ #endif /* @@ -337,9 +337,9 @@ /*----------------------------------------------------------------------- * Cache Configuration */ -#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */ +#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */ #if defined(CONFIG_CMD_KGDB) -# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ #endif /*----------------------------------------------------------------------- @@ -352,17 +352,17 @@ * * HID1 has only read-only information - nothing to set. */ -#define CFG_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\ +#define CONFIG_SYS_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\ HID0_IFEM|HID0_ABE) -#define CFG_HID0_FINAL (HID0_ICE|HID0_IFEM|HID0_ABE) -#define CFG_HID2 0 +#define CONFIG_SYS_HID0_FINAL (HID0_ICE|HID0_IFEM|HID0_ABE) +#define CONFIG_SYS_HID2 0 /*----------------------------------------------------------------------- * RMR - Reset Mode Register 5-5 *----------------------------------------------------------------------- * turn on Checkstop Reset Enable */ -#define CFG_RMR RMR_CSRE +#define CONFIG_SYS_RMR RMR_CSRE /*----------------------------------------------------------------------- * BCR - Bus Configuration 4-25 @@ -370,16 +370,16 @@ */ #define BCR_APD01 0x10000000 -#define CFG_BCR (BCR_APD01|BCR_ETM|BCR_LETM) /* 8260 mode */ +#define CONFIG_SYS_BCR (BCR_APD01|BCR_ETM|BCR_LETM) /* 8260 mode */ /*----------------------------------------------------------------------- * SIUMCR - SIU Module Configuration 4-31 *----------------------------------------------------------------------- */ #if 0 -#define CFG_SIUMCR (SIUMCR_DPPC00|SIUMCR_APPC10|SIUMCR_CS10PC01) +#define CONFIG_SYS_SIUMCR (SIUMCR_DPPC00|SIUMCR_APPC10|SIUMCR_CS10PC01) #else -#define CFG_SIUMCR (SIUMCR_DPPC10|SIUMCR_APPC10) +#define CONFIG_SYS_SIUMCR (SIUMCR_DPPC10|SIUMCR_APPC10) #endif @@ -390,10 +390,10 @@ * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable */ #if defined(CONFIG_WATCHDOG) -#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ +#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE) #else -#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ +#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ SYPCR_SWRI|SYPCR_SWP) #endif /* CONFIG_WATCHDOG */ @@ -403,7 +403,7 @@ * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, * and enable Time Counter */ -#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) +#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) /*----------------------------------------------------------------------- * PISCR - Periodic Interrupt Status and Control 4-42 @@ -411,19 +411,19 @@ * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable * Periodic timer */ -#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) +#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) /*----------------------------------------------------------------------- * SCCR - System Clock Control 9-8 *----------------------------------------------------------------------- */ -#define CFG_SCCR (SCCR_DFBRG00) +#define CONFIG_SYS_SCCR (SCCR_DFBRG00) /*----------------------------------------------------------------------- * RCCR - RISC Controller Configuration 13-7 *----------------------------------------------------------------------- */ -#define CFG_RCCR 0 +#define CONFIG_SYS_RCCR 0 /* * Init Memory Controller: @@ -437,34 +437,34 @@ /* Initialize SDRAM on local bus */ -#define CFG_INIT_LOCAL_SDRAM +#define CONFIG_SYS_INIT_LOCAL_SDRAM /* Minimum mask to separate preliminary * address ranges for CS[0:2] */ -#define CFG_MIN_AM_MASK 0xC0000000 +#define CONFIG_SYS_MIN_AM_MASK 0xC0000000 /* * we use the same values for 32 MB and 128 MB SDRAM * refresh rate = 7.68 uS (100 MHz Bus Clock) */ -#define CFG_MPTPR 0x2000 -#define CFG_PSRT 0x16 +#define CONFIG_SYS_MPTPR 0x2000 +#define CONFIG_SYS_PSRT 0x16 -#define CFG_MRS_OFFS 0x00000000 +#define CONFIG_SYS_MRS_OFFS 0x00000000 #if defined(CONFIG_BOOT_ROM) /* * Bank 0 - Boot ROM (8 bit wide) */ -#define CFG_BR0_PRELIM ((CFG_BOOTROM_BASE & BRx_BA_MSK)|\ +#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_BOOTROM_BASE & BRx_BA_MSK)|\ BRx_PS_8 |\ BRx_MS_GPCM_P |\ BRx_V) -#define CFG_OR0_PRELIM (P2SZ_TO_AM(CFG_BOOTROM_SIZE) |\ +#define CONFIG_SYS_OR0_PRELIM (P2SZ_TO_AM(CONFIG_SYS_BOOTROM_SIZE) |\ ORxG_CSNT |\ ORxG_ACS_DIV1 |\ ORxG_SCY_5_CLK |\ @@ -474,12 +474,12 @@ /* * Bank 1 - Flash (64 bit wide) */ -#define CFG_BR1_PRELIM ((CFG_FLASH_BASE & BRx_BA_MSK) |\ +#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\ BRx_PS_64 |\ BRx_MS_GPCM_P |\ BRx_V) -#define CFG_OR1_PRELIM (P2SZ_TO_AM(CFG_FLASH_SIZE) |\ +#define CONFIG_SYS_OR1_PRELIM (P2SZ_TO_AM(CONFIG_SYS_FLASH_SIZE) |\ ORxG_CSNT |\ ORxG_ACS_DIV1 |\ ORxG_SCY_5_CLK |\ @@ -491,12 +491,12 @@ /* * Bank 0 - Flash (64 bit wide) */ -#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BRx_BA_MSK) |\ +#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\ BRx_PS_64 |\ BRx_MS_GPCM_P |\ BRx_V) -#define CFG_OR0_PRELIM (P2SZ_TO_AM(CFG_FLASH_SIZE) |\ +#define CONFIG_SYS_OR0_PRELIM (P2SZ_TO_AM(CONFIG_SYS_FLASH_SIZE) |\ ORxG_CSNT |\ ORxG_ACS_DIV1 |\ ORxG_SCY_5_CLK |\ @@ -506,12 +506,12 @@ /* * Bank 1 - Disk-On-Chip */ -#define CFG_BR1_PRELIM ((CFG_DOC_BASE & BRx_BA_MSK) |\ +#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_DOC_BASE & BRx_BA_MSK) |\ BRx_PS_8 |\ BRx_MS_GPCM_P |\ BRx_V) -#define CFG_OR1_PRELIM (P2SZ_TO_AM(CFG_DOC_SIZE) |\ +#define CONFIG_SYS_OR1_PRELIM (P2SZ_TO_AM(CONFIG_SYS_DOC_SIZE) |\ ORxG_CSNT |\ ORxG_ACS_DIV1 |\ ORxG_SCY_5_CLK |\ @@ -523,20 +523,20 @@ /* Bank 2 - SDRAM */ -#ifndef CFG_RAMBOOT -#define CFG_BR2_PRELIM ((CFG_SDRAM_BASE & BRx_BA_MSK) |\ +#ifndef CONFIG_SYS_RAMBOOT +#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\ BRx_PS_64 |\ BRx_MS_SDRAM_P |\ BRx_V) /* SDRAM initialization values for 8-column chips */ -#define CFG_OR2_8COL (CFG_MIN_AM_MASK |\ +#define CONFIG_SYS_OR2_8COL (CONFIG_SYS_MIN_AM_MASK |\ ORxS_BPD_4 |\ ORxS_ROWST_PBI0_A9 |\ ORxS_NUMR_12) -#define CFG_PSDMR_8COL (PSDMR_SDAM_A13_IS_A5 |\ +#define CONFIG_SYS_PSDMR_8COL (PSDMR_SDAM_A13_IS_A5 |\ PSDMR_BSMA_A14_A16 |\ PSDMR_SDA10_PBI0_A10 |\ PSDMR_RFRC_7_CLK |\ @@ -548,12 +548,12 @@ /* SDRAM initialization values for 9-column chips */ -#define CFG_OR2_9COL (CFG_MIN_AM_MASK |\ +#define CONFIG_SYS_OR2_9COL (CONFIG_SYS_MIN_AM_MASK |\ ORxS_BPD_4 |\ ORxS_ROWST_PBI0_A7 |\ ORxS_NUMR_13) -#define CFG_PSDMR_9COL (PSDMR_SDAM_A14_IS_A5 |\ +#define CONFIG_SYS_PSDMR_9COL (PSDMR_SDAM_A14_IS_A5 |\ PSDMR_BSMA_A13_A15 |\ PSDMR_SDA10_PBI0_A9 |\ PSDMR_RFRC_7_CLK |\ @@ -563,9 +563,9 @@ PSDMR_WRC_1C |\ PSDMR_CL_2) -#define CFG_OR2_PRELIM CFG_OR2_9COL -#define CFG_PSDMR CFG_PSDMR_9COL +#define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_OR2_9COL +#define CONFIG_SYS_PSDMR CONFIG_SYS_PSDMR_9COL -#endif /* CFG_RAMBOOT */ +#endif /* CONFIG_SYS_RAMBOOT */ #endif /* __CONFIG_H */ |