diff options
Diffstat (limited to 'include/configs/PM520.h')
| -rw-r--r-- | include/configs/PM520.h | 180 |
1 files changed, 90 insertions, 90 deletions
diff --git a/include/configs/PM520.h b/include/configs/PM520.h index 2676d7d..e250e03 100644 --- a/include/configs/PM520.h +++ b/include/configs/PM520.h @@ -33,7 +33,7 @@ #define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ #define CONFIG_PM520 1 /* ... on PM520 board */ -#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33MHz */ +#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33MHz */ #define CONFIG_MISC_INIT_R @@ -47,7 +47,7 @@ */ #define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ #define CONFIG_BAUDRATE 9600 /* ... at 9600 bps */ -#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } #ifdef CONFIG_MPC5200 /* MPC5100 PCI is not supported yet. */ @@ -72,7 +72,7 @@ #define CONFIG_NET_MULTI 1 #define CONFIG_MII 1 #define CONFIG_EEPRO100 1 -#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ +#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ #undef CONFIG_NS8382X #endif @@ -161,42 +161,42 @@ /* * IPB Bus clocking configuration. */ -#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ +#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ #endif /* * I2C configuration */ #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CFG_I2C_MODULE 2 /* Select I2C module #1 or #2 */ +#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ -#define CFG_I2C_SPEED 100000 /* 100 kHz */ -#define CFG_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ +#define CONFIG_SYS_I2C_SLAVE 0x7F /* * EEPROM configuration */ -#define CFG_I2C_EEPROM_ADDR 0x58 -#define CFG_I2C_EEPROM_ADDR_LEN 1 -#define CFG_EEPROM_PAGE_WRITE_BITS 4 -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x58 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* * RTC configuration */ #define CONFIG_RTC_PCF8563 -#define CFG_I2C_RTC_ADDR 0x51 +#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* * Disk-On-Chip configuration */ -#define CFG_DOC_SHORT_TIMEOUT -#define CFG_MAX_DOC_DEVICE 1 /* Max number of DOC devices */ +#define CONFIG_SYS_DOC_SHORT_TIMEOUT +#define CONFIG_SYS_MAX_DOC_DEVICE 1 /* Max number of DOC devices */ -#define CFG_DOC_SUPPORT_2000 -#define CFG_DOC_SUPPORT_MILLENNIUM -#define CFG_DOC_BASE 0xE0000000 -#define CFG_DOC_SIZE 0x00100000 +#define CONFIG_SYS_DOC_SUPPORT_2000 +#define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM +#define CONFIG_SYS_DOC_BASE 0xE0000000 +#define CONFIG_SYS_DOC_SIZE 0x00100000 #if defined(CONFIG_BOOT_ROM) /* @@ -208,10 +208,10 @@ * 0xFD000000 for 16 MB * 0xFD800000 for 8 MB */ -#define CFG_FLASH_BASE 0xFA000000 -#define CFG_FLASH_SIZE 0x04000000 -#define CFG_BOOTROM_BASE 0xFFF00000 -#define CFG_BOOTROM_SIZE 0x00080000 +#define CONFIG_SYS_FLASH_BASE 0xFA000000 +#define CONFIG_SYS_FLASH_SIZE 0x04000000 +#define CONFIG_SYS_BOOTROM_BASE 0xFFF00000 +#define CONFIG_SYS_BOOTROM_SIZE 0x00080000 #define CONFIG_ENV_ADDR (0xFDF00000 + 0x40000) #else /* @@ -223,19 +223,19 @@ * 0xFF000000 for 16 MB * 0xFF800000 for 8 MB */ -#define CFG_FLASH_BASE 0xFC000000 -#define CFG_FLASH_SIZE 0x04000000 +#define CONFIG_SYS_FLASH_BASE 0xFC000000 +#define CONFIG_SYS_FLASH_SIZE 0x04000000 #define CONFIG_ENV_ADDR (0xFFF00000 + 0x40000) #endif -#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ -#define CFG_MAX_FLASH_SECT 256 /* max num of sects on one chip */ +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max num of sects on one chip */ -#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ -#define CFG_FLASH_LOCK_TOUT 5 /* Timeout for Flash Set Lock Bit (in ms) */ -#define CFG_FLASH_UNLOCK_TOUT 10000 /* Timeout for Flash Clear Lock Bits (in ms) */ -#define CFG_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ +#define CONFIG_SYS_FLASH_LOCK_TOUT 5 /* Timeout for Flash Set Lock Bit (in ms) */ +#define CONFIG_SYS_FLASH_UNLOCK_TOUT 10000 /* Timeout for Flash Clear Lock Bits (in ms) */ +#define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ #define PHYS_FLASH_SECT_SIZE 0x00040000 /* 256 KB sectors (x2) */ @@ -253,27 +253,27 @@ /* * Memory map */ -#define CFG_MBAR 0xf0000000 -#define CFG_SDRAM_BASE 0x00000000 -#define CFG_DEFAULT_MBAR 0x80000000 +#define CONFIG_SYS_MBAR 0xf0000000 +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 /* Use SRAM until RAM will be available */ -#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM -#define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE /* End of used area in DPRAM */ +#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM +#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_SIZE /* End of used area in DPRAM */ -#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET -#define CFG_MONITOR_BASE TEXT_BASE -#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) -# define CFG_RAMBOOT 1 +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +# define CONFIG_SYS_RAMBOOT 1 #endif -#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /* * Ethernet configuration @@ -288,69 +288,69 @@ /* * GPIO configuration */ -#define CFG_GPS_PORT_CONFIG 0x10000004 +#define CONFIG_SYS_GPS_PORT_CONFIG 0x10000004 /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ -#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ +#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ -#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ -#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ +#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ #if defined(CONFIG_CMD_KGDB) -# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ #endif /* * Various low-level settings */ #if defined(CONFIG_MPC5200) -#define CFG_HID0_INIT HID0_ICE | HID0_ICFI -#define CFG_HID0_FINAL HID0_ICE +#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI +#define CONFIG_SYS_HID0_FINAL HID0_ICE #else -#define CFG_HID0_INIT 0 -#define CFG_HID0_FINAL 0 +#define CONFIG_SYS_HID0_INIT 0 +#define CONFIG_SYS_HID0_FINAL 0 #endif #if defined(CONFIG_BOOT_ROM) -#define CFG_BOOTCS_START CFG_BOOTROM_BASE -#define CFG_BOOTCS_SIZE CFG_BOOTROM_SIZE -#define CFG_BOOTCS_CFG 0x00047800 -#define CFG_CS0_START CFG_BOOTROM_BASE -#define CFG_CS0_SIZE CFG_BOOTROM_SIZE -#define CFG_CS1_START CFG_FLASH_BASE -#define CFG_CS1_SIZE CFG_FLASH_SIZE -#define CFG_CS1_CFG 0x0004FF00 +#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_BOOTROM_BASE +#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_BOOTROM_SIZE +#define CONFIG_SYS_BOOTCS_CFG 0x00047800 +#define CONFIG_SYS_CS0_START CONFIG_SYS_BOOTROM_BASE +#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_BOOTROM_SIZE +#define CONFIG_SYS_CS1_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_CS1_SIZE CONFIG_SYS_FLASH_SIZE +#define CONFIG_SYS_CS1_CFG 0x0004FF00 #else -#define CFG_BOOTCS_START CFG_FLASH_BASE -#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE -#define CFG_BOOTCS_CFG 0x0004FF00 -#define CFG_CS0_START CFG_FLASH_BASE -#define CFG_CS0_SIZE CFG_FLASH_SIZE -#define CFG_CS1_START CFG_DOC_BASE -#define CFG_CS1_SIZE CFG_DOC_SIZE -#define CFG_CS1_CFG 0x00047800 +#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE +#define CONFIG_SYS_BOOTCS_CFG 0x0004FF00 +#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE +#define CONFIG_SYS_CS1_START CONFIG_SYS_DOC_BASE +#define CONFIG_SYS_CS1_SIZE CONFIG_SYS_DOC_SIZE +#define CONFIG_SYS_CS1_CFG 0x00047800 #endif -#define CFG_CS_BURST 0x00000000 -#define CFG_CS_DEADCYCLE 0x33333333 +#define CONFIG_SYS_CS_BURST 0x00000000 +#define CONFIG_SYS_CS_DEADCYCLE 0x33333333 -#define CFG_RESET_ADDRESS 0xff000000 +#define CONFIG_SYS_RESET_ADDRESS 0xff000000 /*----------------------------------------------------------------------- * USB stuff @@ -372,23 +372,23 @@ #undef CONFIG_IDE_RESET /* reset for ide supported */ #define CONFIG_IDE_PREINIT -#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CFG_IDE_MAXDEVICE 2 /* max. 2 drive per IDE bus */ +#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drive per IDE bus */ -#define CFG_ATA_IDE0_OFFSET 0x0000 +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 -#define CFG_ATA_BASE_ADDR MPC5XXX_ATA +#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA /* Offset for data I/O */ -#define CFG_ATA_DATA_OFFSET (0x0060) +#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) /* Offset for normal register accesses */ -#define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET) +#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) /* Offset for alternate registers */ -#define CFG_ATA_ALT_OFFSET (0x005C) +#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) /* Interval between registers */ -#define CFG_ATA_STRIDE 4 +#define CONFIG_SYS_ATA_STRIDE 4 #endif /* __CONFIG_H */ |