diff options
Diffstat (limited to 'include/configs/PK1C20.h')
| -rw-r--r-- | include/configs/PK1C20.h | 20 |
1 files changed, 10 insertions, 10 deletions
diff --git a/include/configs/PK1C20.h b/include/configs/PK1C20.h index 91e9518..83a7ec2 100644 --- a/include/configs/PK1C20.h +++ b/include/configs/PK1C20.h @@ -32,7 +32,7 @@ #define CFG_RESET_ADDR 0x00000000 /* Hard-reset address */ #define CFG_EXCEPTION_ADDR 0x01000020 /* Exception entry point*/ -#define CFG_NIOS_SYSID_BASE 0x00920828 /* System id address */ +#define CFG_NIOS_SYSID_BASE 0x021208b8 /* System id address */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* enable early board-spec. init*/ /*------------------------------------------------------------------------ @@ -51,7 +51,7 @@ #define CFG_FLASH_SIZE 0x00800000 /* 8 MByte */ #define CFG_SDRAM_BASE 0x01000000 /* SDRAM base addr */ #define CFG_SDRAM_SIZE 0x01000000 /* 16 MByte */ -#define CFG_SRAM_BASE 0x00800000 /* SRAM base addr */ +#define CFG_SRAM_BASE 0x02000000 /* SRAM base addr */ #define CFG_SRAM_SIZE 0x00100000 /* 1 MB (only 1M mapped)*/ /*------------------------------------------------------------------------ @@ -61,7 +61,7 @@ * -Global data is placed below the heap. * -The stack is placed below global data (&grows down). *----------------------------------------------------------------------*/ -#define CFG_MONITOR_LEN (128 * 1024) /* Reserve 128k */ +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 128k */ #define CFG_GBL_DATA_SIZE 128 /* Global data size rsvd*/ #define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128*1024) @@ -95,9 +95,9 @@ * CONSOLE *----------------------------------------------------------------------*/ #if defined(CONFIG_CONSOLE_JTAG) -#define CFG_NIOS_CONSOLE 0x00920820 /* JTAG UART base addr */ +#define CFG_NIOS_CONSOLE 0x021208b0 /* JTAG UART base addr */ #else -#define CFG_NIOS_CONSOLE 0x009208a0 /* UART base addr */ +#define CFG_NIOS_CONSOLE 0x02120840 /* UART base addr */ #endif #define CFG_NIOS_FIXEDBAUD 1 /* Baudrate is fixed */ @@ -110,9 +110,9 @@ * EPCS Device -- wne CFG_NIOS_EPCSBASE is defined code/commands for * epcs device access is enabled. The base address is the epcs * _register_ base address, NOT THE ADDRESS OF THE MEMORY BLOCK. - * The register base is currently at offset 0x400 from the memory base. + * The register base is currently at offset 0x600 from the memory base. *----------------------------------------------------------------------*/ -#define CFG_NIOS_EPCSBASE 0x00900400 /* EPCS register base */ +#define CFG_NIOS_EPCSBASE 0x02100200 /* EPCS register base */ /*------------------------------------------------------------------------ * DEBUG @@ -126,7 +126,7 @@ * registers, we can slow it down to 10 msec using TMRCNT. If the default * period is acceptable, TMRCNT can be left undefined. *----------------------------------------------------------------------*/ -#define CFG_NIOS_TMRBASE 0x00920860 /* Tick timer base addr */ +#define CFG_NIOS_TMRBASE 0x02120820 /* Tick timer base addr */ #define CFG_NIOS_TMRIRQ 3 /* Timer IRQ num */ #define CFG_NIOS_TMRMS 10 /* 10 msec per tick */ #define CFG_NIOS_TMRCNT (CFG_NIOS_TMRMS * (CONFIG_SYS_CLK_FREQ/1000)) @@ -137,7 +137,7 @@ * must implement its own led routines -- leds are, after all, * board-specific, no? *----------------------------------------------------------------------*/ -#define CFG_LEDPIO_ADDR 0x00920840 /* LED PIO base addr */ +#define CFG_LEDPIO_ADDR 0x02120870 /* LED PIO base addr */ #define CONFIG_STATUS_LED /* Enable status driver */ #define STATUS_LED_BIT 1 /* Bit-0 on PIO */ @@ -150,7 +150,7 @@ * way out to avoid changes there -- define the base address to ensure * cache bypass so there's no need to monkey with inx/outx macros. *----------------------------------------------------------------------*/ -#define CONFIG_SMC91111_BASE 0x80910300 /* Base addr (bypass) */ +#define CONFIG_SMC91111_BASE 0x82110300 /* Base addr (bypass) */ #define CONFIG_DRIVER_SMC91111 /* Using SMC91c111 */ #undef CONFIG_SMC91111_EXT_PHY /* Internal PHY */ #define CONFIG_SMC_USE_32_BIT /* 32-bit interface */ |