diff options
Diffstat (limited to 'include/configs/NETTA2.h')
| -rw-r--r-- | include/configs/NETTA2.h | 654 |
1 files changed, 0 insertions, 654 deletions
diff --git a/include/configs/NETTA2.h b/include/configs/NETTA2.h deleted file mode 100644 index 55ae4b5..0000000 --- a/include/configs/NETTA2.h +++ /dev/null @@ -1,654 +0,0 @@ -/* - * (C) Copyright 2000-2004 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * Pantelis Antoniou, Intracom S.A., panto@intracom.gr - * U-Boot port on NetTA4 board - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#if !defined(CONFIG_NETTA2_VERSION) || CONFIG_NETTA2_VERSION > 2 -#error Unsupported CONFIG_NETTA2 version -#endif - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC870 1 /* This is a MPC885 CPU */ -#define CONFIG_NETTA2 1 /* ...on a NetTA2 board */ - -#define CONFIG_SYS_TEXT_BASE 0x40000000 - -#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ -#undef CONFIG_8xx_CONS_SMC2 -#undef CONFIG_8xx_CONS_NONE - -#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */ - -/* #define CONFIG_XIN 10000000 */ -#define CONFIG_XIN 50000000 -/* #define MPC8XX_HZ 120000000 */ -#define MPC8XX_HZ 66666666 - -#define CONFIG_8xx_GCLK_FREQ MPC8XX_HZ - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#undef CONFIG_CLOCKS_IN_MHZ /* clocks NOT passsed to Linux in MHz */ - -#define CONFIG_PREBOOT "echo;" - -#undef CONFIG_BOOTARGS -#define CONFIG_BOOTCOMMAND \ - "tftpboot; " \ - "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \ - "bootm" - -#define CONFIG_SOURCE -#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */ -#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */ - -#define CONFIG_STATUS_LED 1 /* Status LED enabled */ -#define CONFIG_BOARD_SPECIFIC_LED /* version has board specific leds */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_NISDOMAIN - - -#undef CONFIG_MAC_PARTITION -#undef CONFIG_DOS_PARTITION - -#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */ - -#define FEC_ENET 1 /* eth.c needs it that way... */ -#undef CONFIG_SYS_DISCOVER_PHY -#define CONFIG_MII 1 -#define CONFIG_MII_INIT 1 -#define CONFIG_RMII 1 /* use RMII interface */ - -#define CONFIG_ETHER_ON_FEC1 1 -#define CONFIG_FEC1_PHY 8 /* phy address of FEC */ -#define CONFIG_FEC1_PHY_NORXERR 1 - -#define CONFIG_ETHER_ON_FEC2 1 -#define CONFIG_FEC2_PHY 4 -#define CONFIG_FEC2_PHY_NORXERR 1 - -#define CONFIG_ENV_OVERWRITE 1 /* allow modification of vendor params */ - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_PING -#define CONFIG_CMD_MII -#define CONFIG_CMD_CDP - - -#define CONFIG_BOARD_EARLY_INIT_F 1 -#define CONFIG_MISC_INIT_R - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ - -#define CONFIG_SYS_HUSH_PARSER 1 - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0300000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0700000 /* 3 ... 7 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ -/*----------------------------------------------------------------------- - * Internal Memory Mapped Register - */ -#define CONFIG_SYS_IMMR 0xFF000000 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x3000 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0x40000000 -#if defined(DEBUG) -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#else -#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ -#endif -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#if CONFIG_NETTA2_VERSION == 2 -#define CONFIG_SYS_FLASH_BASE4 0x40080000 -#endif - -#define CONFIG_SYS_RESET_ADDRESS 0x80000000 - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#if CONFIG_NETTA2_VERSION == 1 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#elif CONFIG_NETTA2_VERSION == 2 -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ -#endif -#define CONFIG_SYS_MAX_FLASH_SECT 8 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SECT_SIZE 0x10000 - -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x60000) -#define CONFIG_ENV_OFFSET 0 -#define CONFIG_ENV_SIZE 0x4000 - -#define CONFIG_ENV_ADDR_REDUND (CONFIG_SYS_FLASH_BASE + 0x70000) -#define CONFIG_ENV_OFFSET_REDUND 0 -#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 11-9 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze - */ -#if defined(CONFIG_WATCHDOG) -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) -#else -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) -#endif - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration 11-6 - *----------------------------------------------------------------------- - * PCMCIA config., multi-function pin tri-state - */ -#ifndef CONFIG_CAN_DRIVER -#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC) -#else /* we must activate GPL5 in the SIUMCR for CAN */ -#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC) -#endif /* CONFIG_CAN_DRIVER */ - -/*----------------------------------------------------------------------- - * TBSCR - Time Base Status and Control 11-26 - *----------------------------------------------------------------------- - * Clear Reference Interrupt Status, Timebase freezing enabled - */ -#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) - -/*----------------------------------------------------------------------- - * RTCSC - Real-Time Clock Status and Control Register 11-27 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 11-31 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled - */ -#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) - -/*----------------------------------------------------------------------- - * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 - *----------------------------------------------------------------------- - * Reset PLL lock status sticky bit, timer expired status bit and timer - * interrupt status bit - * - */ - -#if CONFIG_XIN == 10000000 - -#if MPC8XX_HZ == 120000000 -#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ - (0 << PLPRCR_S_SHIFT) | (12 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \ - PLPRCR_TEXPS) -#elif MPC8XX_HZ == 100000000 -#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ - (0 << PLPRCR_S_SHIFT) | (10 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \ - PLPRCR_TEXPS) -#elif MPC8XX_HZ == 50000000 -#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ - (1 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (3 << PLPRCR_PDF_SHIFT) | \ - PLPRCR_TEXPS) -#elif MPC8XX_HZ == 25000000 -#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ - (2 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (3 << PLPRCR_PDF_SHIFT) | \ - PLPRCR_TEXPS) -#elif MPC8XX_HZ == 40000000 -#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ - (1 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (4 << PLPRCR_PDF_SHIFT) | \ - PLPRCR_TEXPS) -#elif MPC8XX_HZ == 75000000 -#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ - (1 << PLPRCR_S_SHIFT) | (15 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \ - PLPRCR_TEXPS) -#else -#error unsupported CPU freq for XIN = 10MHz -#endif - -#elif CONFIG_XIN == 50000000 - -#if MPC8XX_HZ == 120000000 -#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ - (0 << PLPRCR_S_SHIFT) | (12 << PLPRCR_MFI_SHIFT) | (4 << PLPRCR_PDF_SHIFT) | \ - PLPRCR_TEXPS) -#elif MPC8XX_HZ == 100000000 -#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ - (0 << PLPRCR_S_SHIFT) | (6 << PLPRCR_MFI_SHIFT) | (2 << PLPRCR_PDF_SHIFT) | \ - PLPRCR_TEXPS) -#elif MPC8XX_HZ == 66666666 -#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ - (1 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (2 << PLPRCR_PDF_SHIFT) | \ - PLPRCR_TEXPS) -#else -#error unsupported CPU freq for XIN = 50MHz -#endif - -#else - -#error unsupported XIN freq -#endif - - -/* - *----------------------------------------------------------------------- - * SCCR - System Clock and reset Control Register 15-27 - *----------------------------------------------------------------------- - * Set clock output, timebase and RTC source and divider, - * power management and some other internal clocks - * - * Note: When TBS == 0 the timebase is independent of current cpu clock. - */ - -#define SCCR_MASK SCCR_EBDF11 -#if MPC8XX_HZ > 66666666 -#define CONFIG_SYS_SCCR (/* SCCR_TBS | */ SCCR_CRQEN | \ - SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ - SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ - SCCR_DFALCD00 | SCCR_EBDF01) -#else -#define CONFIG_SYS_SCCR (/* SCCR_TBS | */ SCCR_CRQEN | \ - SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ - SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ - SCCR_DFALCD00) -#endif - -/*----------------------------------------------------------------------- - * - *----------------------------------------------------------------------- - * - */ -/*#define CONFIG_SYS_DER 0x2002000F*/ -#define CONFIG_SYS_DER 0 - -/* - * Init Memory Controller: - * - * BR0/1 and OR0/1 (FLASH) - */ - -#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */ - -/* used to re-map FLASH both when starting from SRAM or FLASH: - * restrict access enough to keep SRAM working (if any) - * but not too much to meddle with FLASH accesses - */ -#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */ -#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */ - -/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */ -#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_BI | OR_SCY_5_CLK | OR_TRLX) - -#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) -#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) -#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V ) - -#if CONFIG_NETTA2_VERSION == 2 - -#define FLASH_BASE4_PRELIM 0x40080000 /* FLASH bank #1 */ - -#define CONFIG_SYS_OR4_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) -#define CONFIG_SYS_OR4_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) -#define CONFIG_SYS_BR4_PRELIM ((FLASH_BASE4_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V ) - -#endif - -/* - * BR3 and OR3 (SDRAM) - * - */ -#define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank #0 */ -#define SDRAM_MAX_SIZE (256 << 20) /* max 256MB per bank */ - -/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ -#define CONFIG_SYS_OR_TIMING_SDRAM (OR_CSNT_SAM | OR_G5LS) - -#define CONFIG_SYS_OR3_PRELIM ((0xFFFFFFFFLU & ~(SDRAM_MAX_SIZE - 1)) | CONFIG_SYS_OR_TIMING_SDRAM) -#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMB | BR_PS_32 | BR_V) - -/* - * Memory Periodic Timer Prescaler - */ - -/* - * Memory Periodic Timer Prescaler - * - * The Divider for PTA (refresh timer) configuration is based on an - * example SDRAM configuration (64 MBit, one bank). The adjustment to - * the number of chip selects (NCS) and the actually needed refresh - * rate is done by setting MPTPR. - * - * PTA is calculated from - * PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS) - * - * gclk CPU clock (not bus clock!) - * Trefresh Refresh cycle * 4 (four word bursts used) - * - * 4096 Rows from SDRAM example configuration - * 1000 factor s -> ms - * 32 PTP (pre-divider from MPTPR) from SDRAM example configuration - * 4 Number of refresh cycles per period - * 64 Refresh cycle in ms per number of rows - * -------------------------------------------- - * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000 - * - * 50 MHz => 50.000.000 / Divider = 98 - * 66 Mhz => 66.000.000 / Divider = 129 - * 80 Mhz => 80.000.000 / Divider = 156 - */ - -#define CONFIG_SYS_MAMR_PTA 234 - -/* - * For 16 MBit, refresh rates could be 31.3 us - * (= 64 ms / 2K = 125 / quad bursts). - * For a simpler initialization, 15.6 us is used instead. - * - * #define CONFIG_SYS_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks - * #define CONFIG_SYS_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank - */ -#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ -#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ - -/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ -#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ -#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ - -/* - * MAMR settings for SDRAM - */ - -/* 8 column SDRAM */ -#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ - MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \ - MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) - -/* 9 column SDRAM */ -#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ - MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ - MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) - -#define CONFIG_LAST_STAGE_INIT /* needed to reset the damn phys */ - -/****************************************************************/ - -#define DSP_SIZE 0x00010000 /* 64K */ -#define NAND_SIZE 0x00010000 /* 64K */ - -#define DSP_BASE 0xF1000000 -#define NAND_BASE 0xF1010000 - -/*****************************************************************************/ - -#define CONFIG_SYS_DIRECT_FLASH_TFTP - -/*****************************************************************************/ - -#if CONFIG_NETTA2_VERSION == 1 -#define STATUS_LED_BIT 0x00000008 /* bit 28 */ -#elif CONFIG_NETTA2_VERSION == 2 -#define STATUS_LED_BIT 0x00000080 /* bit 24 */ -#endif - -#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) -#define STATUS_LED_STATE STATUS_LED_BLINKING - -#define STATUS_LED_ACTIVE 0 /* LED on for bit == 0 */ -#define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ - -#ifndef __ASSEMBLY__ - -/* LEDs */ - -/* led_id_t is unsigned int mask */ -typedef unsigned int led_id_t; - -#define __led_toggle(_msk) \ - do { \ - ((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat ^= (_msk); \ - } while(0) - -#define __led_set(_msk, _st) \ - do { \ - if ((_st)) \ - ((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat |= (_msk); \ - else \ - ((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat &= ~(_msk); \ - } while(0) - -#define __led_init(msk, st) __led_set(msk, st) - -#endif - -/*********************************************************************************************************** - - ---------------------------------------------------------------------------------------------- - - (V1) version 1 of the board - (V2) version 2 of the board - - ---------------------------------------------------------------------------------------------- - - Pin definitions: - - +------+----------------+--------+------------------------------------------------------------ - | # | Name | Type | Comment - +------+----------------+--------+------------------------------------------------------------ - | PA3 | SPIEN_MAX | Output | MAX serial to uart chip select - | PA7 | DSP_INT | Output | DSP interrupt - | PA10 | DSP_RESET | Output | DSP reset - | PA14 | USBOE | Output | USB (1) - | PA15 | USBRXD | Output | USB (1) - | PB19 | BT_RTS | Output | Bluetooth (0) - | PB23 | BT_CTS | Output | Bluetooth (0) - | PB26 | SPIEN_SEP | Output | Serial EEPROM chip select - | PB27 | SPICS_DISP | Output | Display chip select - | PB28 | SPI_RXD_3V | Input | SPI Data Rx - | PB29 | SPI_TXD | Output | SPI Data Tx - | PB30 | SPI_CLK | Output | SPI Clock - | PC10 | DISPA0 | Output | Display A0 - | PC11 | BACKLIGHT | Output | Display backlit - | PC12 | SPI2RXD | Input | (V1) 2nd SPI RXD - | | IO_RESET | Output | (V2) General I/O reset - | PC13 | SPI2TXD | Output | (V1) 2nd SPI TXD (V1) - | | HOOK | Input | (V2) Hook input interrupt - | PC15 | SPI2CLK | Output | (V1) 2nd SPI CLK - | | F_RY_BY | Input | (V2) NAND F_RY_BY - | PE17 | F_ALE | Output | NAND F_ALE - | PE18 | F_CLE | Output | NAND F_CLE - | PE20 | F_CE | Output | NAND F_CE - | PE24 | SPICS_SCOUT | Output | (V1) Codec chip select - | | LED | Output | (V2) LED - | PE27 | SPICS_ER | Output | External serial register CS - | PE28 | LEDIO1 | Output | (V1) LED - | | BKBR1 | Input | (V2) Keyboard input scan - | PE29 | LEDIO2 | Output | (V1) LED hook for A (TA2) - | | BKBR2 | Input | (V2) Keyboard input scan - | PE30 | LEDIO3 | Output | (V1) LED hook for A (TA2) - | | BKBR3 | Input | (V2) Keyboard input scan - | PE31 | F_RY_BY | Input | (V1) NAND F_RY_BY - | | BKBR4 | Input | (V2) Keyboard input scan - +------+----------------+--------+--------------------------------------------------- - - ---------------------------------------------------------------------------------------------- - - Serial register input: - - +------+----------------+------------------------------------------------------------ - | # | Name | Comment - +------+----------------+------------------------------------------------------------ - | 4 | HOOK | Hook switch - | 5 | BT_LINK | Bluetooth link status - | 6 | HOST_WAKE | Bluetooth host wake up - | 7 | OK_ETH | Cisco inline power OK status - +------+----------------+------------------------------------------------------------ - - ---------------------------------------------------------------------------------------------- - - Chip selects: - - +------+----------------+------------------------------------------------------------ - | # | Name | Comment - +------+----------------+------------------------------------------------------------ - | CS0 | CS0 | Boot flash - | CS1 | CS_FLASH | NAND flash - | CS2 | CS_DSP | DSP - | CS3 | DCS_DRAM | DRAM - | CS4 | CS_FLASH2 | (V2) 2nd flash - +------+----------------+------------------------------------------------------------ - - ---------------------------------------------------------------------------------------------- - - Interrupts: - - +------+----------------+------------------------------------------------------------ - | # | Name | Comment - +------+----------------+------------------------------------------------------------ - | IRQ1 | IRQ_DSP | DSP interrupt - | IRQ3 | S_INTER | DUSLIC ??? - | IRQ4 | F_RY_BY | NAND - | IRQ7 | IRQ_MAX | MAX 3100 interrupt - +------+----------------+------------------------------------------------------------ - - ---------------------------------------------------------------------------------------------- - - Interrupts on PCMCIA pins: - - +------+----------------+------------------------------------------------------------ - | # | Name | Comment - +------+----------------+------------------------------------------------------------ - | IP_A0| PHY1_LINK | Link status changed for #1 Ethernet interface - | IP_A1| PHY2_LINK | Link status changed for #2 Ethernet interface - | IP_A2| RMII1_MDINT | PHY interrupt for #1 - | IP_A3| RMII2_MDINT | PHY interrupt for #2 - | IP_A5| HOST_WAKE | (V2) Bluetooth host wake - | IP_A6| OK_ETH | (V2) Cisco inline power OK - +------+----------------+------------------------------------------------------------ - -**************************************************************************************************/ - -#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 -#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE 1 -#define CONFIG_SYS_CONSOLE_ENV_OVERWRITE 1 - -/*************************************************************************************************/ - -/* use board specific hardware */ -#undef CONFIG_WATCHDOG /* watchdog disabled */ -#define CONFIG_HW_WATCHDOG - -/*************************************************************************************************/ - -#define CONFIG_CDP_DEVICE_ID 20 -#define CONFIG_CDP_DEVICE_ID_PREFIX "NT" /* netta2 */ -#define CONFIG_CDP_PORT_ID "eth%d" -#define CONFIG_CDP_CAPABILITIES 0x00000010 -#define CONFIG_CDP_VERSION "u-boot" " " U_BOOT_DATE " " U_BOOT_TIME -#define CONFIG_CDP_PLATFORM "Intracom NetTA2" -#define CONFIG_CDP_TRIGGER 0x20020001 -#define CONFIG_CDP_POWER_CONSUMPTION 4300 /* 90 mA @ 48V */ -#define CONFIG_CDP_APPLIANCE_VLAN_TYPE 0x01 /* ipphone ? */ - -/*************************************************************************************************/ - -#define CONFIG_AUTO_COMPLETE 1 - -/*************************************************************************************************/ - -#define CONFIG_CRC32_VERIFY 1 - -/*************************************************************************************************/ - -#define CONFIG_HUSH_OLD_PARSER_COMPATIBLE 1 - -/*************************************************************************************************/ -#endif /* __CONFIG_H */ |