summaryrefslogtreecommitdiff
path: root/include/configs/NETTA.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs/NETTA.h')
-rw-r--r--include/configs/NETTA.h745
1 files changed, 745 insertions, 0 deletions
diff --git a/include/configs/NETTA.h b/include/configs/NETTA.h
new file mode 100644
index 0000000..76e9cb4
--- /dev/null
+++ b/include/configs/NETTA.h
@@ -0,0 +1,745 @@
+/*
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * Pantelis Antoniou, Intracom S.A., panto@intracom.gr
+ * U-Boot port on NetTA4 board
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC885 1 /* This is a MPC885 CPU */
+#define CONFIG_NETTA 1 /* ...on a NetTA board */
+
+#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
+#undef CONFIG_8xx_CONS_SMC2
+#undef CONFIG_8xx_CONS_NONE
+
+#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */
+
+/* #define CONFIG_XIN 10000000 */
+#define CONFIG_XIN 50000000
+#define MPC8XX_HZ 120000000
+/* #define MPC8XX_HZ 100000000 */
+/* #define MPC8XX_HZ 50000000 */
+/* #define MPC8XX_HZ 80000000 */
+
+#define CONFIG_8xx_GCLK_FREQ MPC8XX_HZ
+
+#if 0
+#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
+#else
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#endif
+
+#undef CONFIG_CLOCKS_IN_MHZ /* clocks NOT passsed to Linux in MHz */
+
+#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
+
+#undef CONFIG_BOOTARGS
+#define CONFIG_BOOTCOMMAND \
+ "tftpboot; " \
+ "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \
+ "bootm"
+
+#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */
+#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+#define CONFIG_HW_WATCHDOG
+
+#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE | CONFIG_BOOTP_NISDOMAIN)
+
+#undef CONFIG_MAC_PARTITION
+#undef CONFIG_DOS_PARTITION
+
+#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
+
+#define CONFIG_NET_MULTI 1 /* the only way to get the FEC in */
+#define FEC_ENET 1 /* eth.c needs it that way... */
+#undef CFG_DISCOVER_PHY /* do not discover phys */
+#define CONFIG_MII 1
+#define CONFIG_RMII 1 /* use RMII interface */
+
+#if defined(CONFIG_NETTA_ISDN)
+#define CONFIG_ETHER_ON_FEC1 1
+#define CONFIG_FEC1_PHY 1 /* phy address of FEC1 */
+#define CONFIG_FEC1_PHY_NORXERR 1
+#undef CONFIG_ETHER_ON_FEC2
+#else
+#define CONFIG_ETHER_ON_FEC1 1
+#define CONFIG_FEC1_PHY 8 /* phy address of FEC1 */
+#define CONFIG_FEC1_PHY_NORXERR 1
+#define CONFIG_ETHER_ON_FEC2 1
+#define CONFIG_FEC2_PHY 1 /* phy address of FEC2 */
+#define CONFIG_FEC2_PHY_NORXERR 1
+#endif
+
+#define CONFIG_ENV_OVERWRITE 1 /* allow modification of vendor params */
+
+/* POST support */
+#define CONFIG_POST (CFG_POST_MEMORY | \
+ CFG_POST_DSP )
+
+#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
+ CFG_CMD_NAND | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_PING | \
+ CFG_CMD_MII | \
+ CFG_CMD_PCMCIA | CFG_CMD_IDE | CFG_CMD_FAT | \
+ CFG_CMD_DIAG | \
+ CFG_CMD_CDP \
+ )
+
+#define CONFIG_BOARD_EARLY_INIT_F 1
+#define CONFIG_MISC_INIT_R
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
+#define CFG_HUSH_PARSER 1
+#define CFG_PROMPT_HUSH_PS2 "> "
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x0300000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0700000 /* 3 ... 7 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR 0xFF000000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+#define CFG_INIT_RAM_END 0x3000 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE 0x40000000
+#if defined(DEBUG)
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#else
+#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
+#endif
+#define CFG_MONITOR_BASE CFG_FLASH_BASE
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 8 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_SECT_SIZE 0x10000
+
+#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x60000)
+#define CFG_ENV_OFFSET 0
+#define CFG_ENV_SIZE 0x4000
+
+#define CFG_ENV_ADDR_REDUND (CFG_FLASH_BASE + 0x70000)
+#define CFG_ENV_OFFSET_REDUND 0
+#define CFG_ENV_SIZE_REDUND CFG_ENV_SIZE
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
+#else
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+#ifndef CONFIG_CAN_DRIVER
+#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC)
+#else /* we must activate GPL5 in the SIUMCR for CAN */
+#define CFG_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC)
+#endif /* CONFIG_CAN_DRIVER */
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control 11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+
+/*-----------------------------------------------------------------------
+ * RTCSC - Real-Time Clock Status and Control Register 11-27
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR (PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer
+ * interrupt status bit
+ *
+ */
+
+#if CONFIG_XIN == 10000000
+
+#if MPC8XX_HZ == 120000000
+#define CFG_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
+ (0 << PLPRCR_S_SHIFT) | (12 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \
+ PLPRCR_TEXPS)
+#elif MPC8XX_HZ == 100000000
+#define CFG_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
+ (0 << PLPRCR_S_SHIFT) | (10 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \
+ PLPRCR_TEXPS)
+#elif MPC8XX_HZ == 50000000
+#define CFG_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
+ (1 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (3 << PLPRCR_PDF_SHIFT) | \
+ PLPRCR_TEXPS)
+#elif MPC8XX_HZ == 25000000
+#define CFG_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
+ (2 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (3 << PLPRCR_PDF_SHIFT) | \
+ PLPRCR_TEXPS)
+#elif MPC8XX_HZ == 40000000
+#define CFG_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
+ (1 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (4 << PLPRCR_PDF_SHIFT) | \
+ PLPRCR_TEXPS)
+#elif MPC8XX_HZ == 75000000
+#define CFG_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
+ (1 << PLPRCR_S_SHIFT) | (15 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \
+ PLPRCR_TEXPS)
+#else
+#error unsupported CPU freq for XIN = 10MHz
+#endif
+
+#elif CONFIG_XIN == 50000000
+
+#if MPC8XX_HZ == 120000000
+#define CFG_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
+ (0 << PLPRCR_S_SHIFT) | (12 << PLPRCR_MFI_SHIFT) | (4 << PLPRCR_PDF_SHIFT) | \
+ PLPRCR_TEXPS)
+#elif MPC8XX_HZ == 100000000
+#define CFG_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
+ (0 << PLPRCR_S_SHIFT) | (6 << PLPRCR_MFI_SHIFT) | (2 << PLPRCR_PDF_SHIFT) | \
+ PLPRCR_TEXPS)
+#elif MPC8XX_HZ == 80000000
+#define CFG_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
+ (0 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (4 << PLPRCR_PDF_SHIFT) | \
+ PLPRCR_TEXPS)
+#elif MPC8XX_HZ == 50000000
+#define CFG_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
+ (1 << PLPRCR_S_SHIFT) | (6 << PLPRCR_MFI_SHIFT) | (2 << PLPRCR_PDF_SHIFT) | \
+ PLPRCR_TEXPS)
+#else
+#error unsupported CPU freq for XIN = 50MHz
+#endif
+
+#else
+
+#error unsupported XIN freq
+#endif
+
+
+/*
+ *-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register 15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+
+#define SCCR_MASK SCCR_EBDF11
+#if MPC8XX_HZ > 66666666
+#define CFG_SCCR (SCCR_TBS | \
+ SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
+ SCCR_DFNL001 | SCCR_DFNH000 | SCCR_DFLCD000 | \
+ SCCR_DFALCD00 | SCCR_EBDF01)
+#else
+#define CFG_SCCR (SCCR_TBS | \
+ SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
+ SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
+ SCCR_DFALCD00)
+#endif
+
+/*-----------------------------------------------------------------------
+ *
+ *-----------------------------------------------------------------------
+ *
+ */
+/*#define CFG_DER 0x2002000F*/
+#define CFG_DER 0
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
+
+/* used to re-map FLASH both when starting from SRAM or FLASH:
+ * restrict access enough to keep SRAM working (if any)
+ * but not too much to meddle with FLASH accesses
+ */
+#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */
+#define CFG_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
+
+/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */
+#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_BI | OR_SCY_5_CLK | OR_TRLX)
+
+#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH)
+#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
+#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V )
+
+/*
+ * BR3 and OR3 (SDRAM)
+ *
+ */
+#define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank #0 */
+#define SDRAM_MAX_SIZE (256 << 20) /* max 256MB per bank */
+
+/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
+#define CFG_OR_TIMING_SDRAM (OR_CSNT_SAM | OR_G5LS)
+
+#define CFG_OR3_PRELIM ((0xFFFFFFFFLU & ~(SDRAM_MAX_SIZE - 1)) | CFG_OR_TIMING_SDRAM)
+#define CFG_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMB | BR_PS_32 | BR_V)
+
+/*
+ * Memory Periodic Timer Prescaler
+ */
+
+/*
+ * Memory Periodic Timer Prescaler
+ *
+ * The Divider for PTA (refresh timer) configuration is based on an
+ * example SDRAM configuration (64 MBit, one bank). The adjustment to
+ * the number of chip selects (NCS) and the actually needed refresh
+ * rate is done by setting MPTPR.
+ *
+ * PTA is calculated from
+ * PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
+ *
+ * gclk CPU clock (not bus clock!)
+ * Trefresh Refresh cycle * 4 (four word bursts used)
+ *
+ * 4096 Rows from SDRAM example configuration
+ * 1000 factor s -> ms
+ * 32 PTP (pre-divider from MPTPR) from SDRAM example configuration
+ * 4 Number of refresh cycles per period
+ * 64 Refresh cycle in ms per number of rows
+ * --------------------------------------------
+ * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
+ *
+ * 50 MHz => 50.000.000 / Divider = 98
+ * 66 Mhz => 66.000.000 / Divider = 129
+ * 80 Mhz => 80.000.000 / Divider = 156
+ */
+
+#if MPC8XX_HZ == 120000000
+#define CFG_MAMR_PTA 234
+#elif MPC8XX_HZ == 100000000
+#define CFG_MAMR_PTA 195
+#elif MPC8XX_HZ == 80000000
+#define CFG_MAMR_PTA 156
+#elif MPC8XX_HZ == 50000000
+#define CFG_MAMR_PTA 98
+#else
+#error Unknown frequency
+#endif
+
+
+/*
+ * For 16 MBit, refresh rates could be 31.3 us
+ * (= 64 ms / 2K = 125 / quad bursts).
+ * For a simpler initialization, 15.6 us is used instead.
+ *
+ * #define CFG_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks
+ * #define CFG_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank
+ */
+#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
+#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
+
+/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
+#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
+#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
+
+/*
+ * MAMR settings for SDRAM
+ */
+
+/* 8 column SDRAM */
+#define CFG_MAMR_8COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
+ MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
+ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
+
+/* 9 column SDRAM */
+#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
+ MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
+ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#define CONFIG_ARTOS /* include ARTOS support */
+
+#define CONFIG_LAST_STAGE_INIT /* needed to reset the damn phys */
+
+/***********************************************************************************************************
+
+ Pin definitions:
+
+ +------+----------------+--------+------------------------------------------------------------
+ | # | Name | Type | Comment
+ +------+----------------+--------+------------------------------------------------------------
+ | PA3 | OK_ETH_3V | Input | CISCO Ethernet power OK
+ | | | | (NetRoute: FEC1, TA: FEC2) (0=power OK)
+ | PA6 | P_VCCD1 | Output | TPS2211A PCMCIA
+ | PA7 | DCL1_3V | Periph | IDL1 PCM clock
+ | PA8 | DSP_DR1 | Periph | IDL1 PCM Data Rx
+ | PA9 | L1TXDA | Periph | IDL1 PCM Data Tx
+ | PA10 | P_VCCD0 | Output | TPS2211A PCMCIA
+ | PA12 | P_SHDN | Output | TPS2211A PCMCIA
+ | PA13 | ETH_LOOP | Output | CISCO Loopback remote power
+ | | | | (NetRoute: FEC1, TA: FEC2) (1=NORMAL)
+ | PA14 | P_VPPD0 | Output | TPS2211A PCMCIA
+ | PA15 | P_VPPD1 | Output | TPS2211A PCMCIA
+ | PB14 | SPIEN_FXO | Output | SPI CS for FXO daughter-board
+ | PB15 | SPIEN_S1 | Output | SPI CS for S-interface 1 (NetRoute only)
+ | PB16 | DREQ1 | Output | D channel request for S-interface chip 1.
+ | PB17 | L1ST3 | Periph | IDL1 timeslot enable signal for PPC
+ | PB18 | L1ST2 | Periph | IDL1 timeslot enable signal for PPC
+ | PB19 | SPIEN_S2 | Output | SPI CS for S-interface 2 (NetRoute only)
+ | PB20 | SPIEN_SEEPROM | Output | SPI CS for serial eeprom
+ | PB21 | LEDIO | Output | Led mode indication for PHY
+ | PB22 | UART_CTS | Input | UART CTS
+ | PB23 | UART_RTS | Output | UART RTS
+ | PB24 | UART_RX | Periph | UART Data Rx
+ | PB25 | UART_TX | Periph | UART Data Tx
+ | PB26 | RMII-MDC | Periph | Free for future use (MII mgt clock)
+ | PB27 | RMII-MDIO | Periph | Free for future use (MII mgt data)
+ | PB28 | SPI_RXD_3V | Input | SPI Data Rx
+ | PB29 | SPI_TXD | Output | SPI Data Tx
+ | PB30 | SPI_CLK | Output | SPI Clock
+ | PB31 | RMII1-REFCLK | Periph | RMII reference clock for FEC1
+ | PC4 | PHY1_LINK | Input | PHY link state FEC1 (interrupt)
+ | PC5 | PHY2_LINK | Input | PHY link state FEC2 (interrupt)
+ | PC6 | RMII1-MDINT | Input | PHY prog interrupt FEC1 (interrupt)
+ | PC7 | RMII2-MDINT | Input | PHY prog interrupt FEC1 (interrupt)
+ | PC8 | P_OC | Input | TPS2211A PCMCIA overcurrent (interrupt) (1=OK)
+ | PC9 | COM_HOOK1 | Input | Codec interrupt chip #1 (interrupt)
+ | PC10 | COM_HOOK2 | Input | Codec interrupt chip #2 (interrupt)
+ | PC11 | COM_HOOK4 | Input | Codec interrupt chip #4 (interrupt)
+ | PC12 | COM_HOOK3 | Input | Codec interrupt chip #3 (interrupt)
+ | PC13 | F_RY_BY | Input | NAND ready signal (interrupt)
+ | PC14 | FAN_OK | Input | Fan status signal (interrupt) (1=OK)
+ | PC15 | PC15_DIRECT0 | Periph | PCMCIA DMA request.
+ | PD3 | F_ALE | Output | NAND
+ | PD4 | F_CLE | Output | NAND
+ | PD5 | F_CE | Output | NAND
+ | PD6 | DSP_INT | Output | DSP debug interrupt
+ | PD7 | DSP_RESET | Output | DSP reset
+ | PD8 | RMII_MDC | Periph | MII mgt clock
+ | PD9 | SPIEN_C1 | Output | SPI CS for codec #1
+ | PD10 | SPIEN_C2 | Output | SPI CS for codec #2
+ | PD11 | SPIEN_C3 | Output | SPI CS for codec #3
+ | PD12 | FSC2 | Periph | IDL2 frame sync
+ | PD13 | DGRANT2 | Input | D channel grant from S #2
+ | PD14 | SPIEN_C4 | Output | SPI CS for codec #4
+ | PD15 | TP700 | Output | Testpoint for software debugging
+ | PE14 | RMII2-TXD0 | Periph | FEC2 transmit data
+ | PE15 | RMII2-TXD1 | Periph | FEC2 transmit data
+ | PE16 | RMII2-REFCLK | Periph | TA: RMII ref clock for
+ | | DCL2 | Periph | NetRoute: PCM clock #2
+ | PE17 | TP703 | Output | Testpoint for software debugging
+ | PE18 | DGRANT1 | Input | D channel grant from S #1
+ | PE19 | RMII2-TXEN | Periph | TA: FEC2 tx enable
+ | | PCM2OUT | Periph | NetRoute: Tx data for IDL2
+ | PE20 | FSC1 | Periph | IDL1 frame sync
+ | PE21 | RMII2-RXD0 | Periph | FEC2 receive data
+ | PE22 | RMII2-RXD1 | Periph | FEC2 receive data
+ | PE23 | L1ST1 | Periph | IDL1 timeslot enable signal for PPC
+ | PE24 | U-N1 | Output | Select user/network for S #1 (0=user)
+ | PE25 | U-N2 | Output | Select user/network for S #2 (0=user)
+ | PE26 | RMII2-RXDV | Periph | FEC2 valid
+ | PE27 | DREQ2 | Output | D channel request for S #2.
+ | PE28 | FPGA_DONE | Input | FPGA done signal
+ | PE29 | FPGA_INIT | Output | FPGA init signal
+ | PE30 | UDOUT2_3V | Input | IDL2 PCM input
+ | PE31 | | | Free
+ +------+----------------+--------+---------------------------------------------------
+
+ Chip selects:
+
+ +------+----------------+------------------------------------------------------------
+ | # | Name | Comment
+ +------+----------------+------------------------------------------------------------
+ | CS0 | CS0 | Boot flash
+ | CS1 | CS_FLASH | NAND flash
+ | CS2 | CS_DSP | DSP
+ | CS3 | DCS_DRAM | DRAM
+ | CS4 | CS_ER1 | External output register
+ +------+----------------+------------------------------------------------------------
+
+ Interrupts:
+
+ +------+----------------+------------------------------------------------------------
+ | # | Name | Comment
+ +------+----------------+------------------------------------------------------------
+ | IRQ1 | UINTER_3V | S interupt chips interrupt (common)
+ | IRQ3 | IRQ_DSP | DSP interrupt
+ | IRQ4 | IRQ_DSP1 | Extra DSP interrupt
+ +------+----------------+------------------------------------------------------------
+
+*************************************************************************************************/
+
+#define DSP_SIZE 0x00010000 /* 64K */
+#define NAND_SIZE 0x00010000 /* 64K */
+#define ER_SIZE 0x00010000 /* 64K */
+#define DUMMY_SIZE 0x00010000 /* 64K */
+
+#define DSP_BASE 0xF1000000
+#define NAND_BASE 0xF1010000
+#define ER_BASE 0xF1020000
+#define DUMMY_BASE 0xF1FF0000
+
+/****************************************************************/
+
+/* NAND */
+#define CFG_NAND_BASE NAND_BASE
+#define CONFIG_MTD_NAND_ECC_JFFS2
+
+#define CFG_MAX_NAND_DEVICE 1
+#define NAND_NO_RB
+
+#define SECTORSIZE 512
+#define ADDR_COLUMN 1
+#define ADDR_PAGE 2
+#define ADDR_COLUMN_PAGE 3
+#define NAND_ChipID_UNKNOWN 0x00
+#define NAND_MAX_FLOORS 1
+#define NAND_MAX_CHIPS 1
+
+/* ALE = PD3, CLE = PD4, CE = PD5, F_RY_BY = PC13 */
+#define NAND_DISABLE_CE(nand) \
+ do { \
+ (((volatile immap_t *)CFG_IMMR)->im_ioport.iop_pddat) |= (1 << (15 - 5)); \
+ } while(0)
+
+#define NAND_ENABLE_CE(nand) \
+ do { \
+ (((volatile immap_t *)CFG_IMMR)->im_ioport.iop_pddat) &= ~(1 << (15 - 5)); \
+ } while(0)
+
+#define NAND_CTL_CLRALE(nandptr) \
+ do { \
+ (((volatile immap_t *)CFG_IMMR)->im_ioport.iop_pddat) &= ~(1 << (15 - 3)); \
+ } while(0)
+
+#define NAND_CTL_SETALE(nandptr) \
+ do { \
+ (((volatile immap_t *)CFG_IMMR)->im_ioport.iop_pddat) |= (1 << (15 - 3)); \
+ } while(0)
+
+#define NAND_CTL_CLRCLE(nandptr) \
+ do { \
+ (((volatile immap_t *)CFG_IMMR)->im_ioport.iop_pddat) &= ~(1 << (15 - 4)); \
+ } while(0)
+
+#define NAND_CTL_SETCLE(nandptr) \
+ do { \
+ (((volatile immap_t *)CFG_IMMR)->im_ioport.iop_pddat) |= (1 << (15 - 4)); \
+ } while(0)
+
+#ifndef NAND_NO_RB
+#define NAND_WAIT_READY(nand) \
+ do { \
+ while ((((volatile immap_t *)CFG_IMMR)->im_ioport.iop_pcdat & (1 << (15 - 13))) == 0) { \
+ WATCHDOG_RESET(); \
+ } \
+ } while (0)
+#else
+#define NAND_WAIT_READY(nand) udelay(12)
+#endif
+
+#define WRITE_NAND_COMMAND(d, adr) \
+ do { \
+ *(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \
+ } while(0)
+
+#define WRITE_NAND_ADDRESS(d, adr) \
+ do { \
+ *(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \
+ } while(0)
+
+#define WRITE_NAND(d, adr) \
+ do { \
+ *(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \
+ } while(0)
+
+#define READ_NAND(adr) \
+ ((unsigned char)(*(volatile unsigned char *)(unsigned long)(adr)))
+
+/*****************************************************************************/
+
+#if 1
+/*-----------------------------------------------------------------------
+ * PCMCIA stuff
+ *-----------------------------------------------------------------------
+ */
+
+#define CFG_PCMCIA_MEM_ADDR (0xE0000000)
+#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_DMA_ADDR (0xE4000000)
+#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000)
+#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_IO_ADDR (0xEC000000)
+#define CFG_PCMCIA_IO_SIZE ( 64 << 20 )
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
+ *-----------------------------------------------------------------------
+ */
+
+#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
+
+#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
+#undef CONFIG_IDE_LED /* LED for ide not supported */
+#undef CONFIG_IDE_RESET /* reset for ide not supported */
+
+#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
+
+#define CFG_ATA_IDE0_OFFSET 0x0000
+
+#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR
+
+/* Offset for data I/O */
+#define CFG_ATA_DATA_OFFSET (CFG_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for normal register accesses */
+#define CFG_ATA_REG_OFFSET (2 * CFG_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for alternate registers */
+#define CFG_ATA_ALT_OFFSET 0x0100
+
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+#endif
+
+/*************************************************************************************************/
+
+#define CONFIG_CDP_DEVICE_ID 20
+#define CONFIG_CDP_DEVICE_ID_PREFIX "NT" /* netta */
+#define CONFIG_CDP_PORT_ID "eth%d"
+#define CONFIG_CDP_CAPABILITIES 0x00000010
+#define CONFIG_CDP_VERSION "u-boot 1.0" " " __DATE__ " " __TIME__
+#define CONFIG_CDP_PLATFORM "Intracom NetTA"
+#define CONFIG_CDP_TRIGGER 0x20020001
+#define CONFIG_CDP_POWER_CONSUMPTION 4300 /* 90 mA @ 48V */
+#define CONFIG_CDP_APPLIANCE_VLAN_TYPE 0x01 /* ipphone? */
+
+/*************************************************************************************************/
+
+#define CONFIG_AUTO_COMPLETE 1
+
+/*************************************************************************************************/
+
+#endif /* __CONFIG_H */