diff options
Diffstat (limited to 'include/configs/MPC8641HPCN.h')
| -rw-r--r-- | include/configs/MPC8641HPCN.h | 252 |
1 files changed, 126 insertions, 126 deletions
diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h index a8d0077..9acc3da 100644 --- a/include/configs/MPC8641HPCN.h +++ b/include/configs/MPC8641HPCN.h @@ -36,11 +36,11 @@ #define CONFIG_MPC86xx 1 /* MPC86xx */ #define CONFIG_MPC8641 1 /* MPC8641 specific */ #define CONFIG_MPC8641HPCN 1 /* MPC8641HPCN board specific */ -#define CONFIG_NUM_CPUS 2 /* Number of CPUs in the system */ -#define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ +#define CONFIG_NUM_CPUS 2 /* Number of CPUs in the system */ +#define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ #ifdef RUN_DIAG -#define CFG_DIAG_ADDR 0xff800000 +#define CFG_DIAG_ADDR 0xff800000 #endif #define CFG_RESET_ADDRESS 0xfff00100 @@ -51,7 +51,7 @@ #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ #define CONFIG_FSL_LAW 1 /* Use common FSL law init code */ -#define CONFIG_TSEC_ENET /* tsec ethernet support */ +#define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_ENV_OVERWRITE #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ @@ -61,14 +61,14 @@ #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ #define CONFIG_MEM_INIT_VALUE 0xDeadBeef #define CONFIG_NUM_DDR_CONTROLLERS 2 -/* #define CONFIG_DDR_INTERLEAVE 1 */ +/* #define CONFIG_DDR_INTERLEAVE 1 */ #define CACHE_LINE_INTERLEAVING 0x20000000 #define PAGE_INTERLEAVING 0x21000000 #define BANK_INTERLEAVING 0x22000000 #define SUPER_BANK_INTERLEAVING 0x23000000 -#define CONFIG_ALTIVEC 1 +#define CONFIG_ALTIVEC 1 /* * L2CR setup -- make sure this is right for your board! @@ -81,7 +81,7 @@ #ifndef __ASSEMBLY__ extern unsigned long get_board_sys_clk(unsigned long dummy); #endif -#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) +#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) #endif #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ @@ -94,7 +94,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) */ -#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ #define CFG_CCSRBAR 0xf8000000 /* relocated CCSRBAR */ #define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ @@ -127,18 +127,18 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CFG_SDRAM_SIZE 256 /* DDR is 256MB */ #define CFG_DDR_CS0_BNDS 0x0000000F - #define CFG_DDR_CS0_CONFIG 0x80010102 /* Enable, no interleaving */ + #define CFG_DDR_CS0_CONFIG 0x80010102 /* Enable, no interleaving */ #define CFG_DDR_EXT_REFRESH 0x00000000 - #define CFG_DDR_TIMING_0 0x00260802 + #define CFG_DDR_TIMING_0 0x00260802 #define CFG_DDR_TIMING_1 0x39357322 #define CFG_DDR_TIMING_2 0x14904cc8 #define CFG_DDR_MODE_1 0x00480432 #define CFG_DDR_MODE_2 0x00000000 #define CFG_DDR_INTERVAL 0x06090100 - #define CFG_DDR_DATA_INIT 0xdeadbeef - #define CFG_DDR_CLK_CTRL 0x03800000 - #define CFG_DDR_OCD_CTRL 0x00000000 - #define CFG_DDR_OCD_STATUS 0x00000000 + #define CFG_DDR_DATA_INIT 0xdeadbeef + #define CFG_DDR_CLK_CTRL 0x03800000 + #define CFG_DDR_OCD_CTRL 0x00000000 + #define CFG_DDR_OCD_STATUS 0x00000000 #define CFG_DDR_CONTROL 0xe3008000 /* Type = DDR2 */ #define CFG_DDR_CONTROL2 0x04400000 @@ -170,7 +170,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); * * Note that, on switching the boot location, fef00000 becomes fff00000. */ -#define CFG_FLASH_BASE 0xfe800000 /* start of FLASH 32M */ +#define CFG_FLASH_BASE 0xfe800000 /* start of FLASH 32M */ #define CFG_FLASH_BASE2 0xff800000 #define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE2} @@ -189,7 +189,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */ -#define PIXIS_BASE 0xf8100000 /* PIXIS registers */ +#define PIXIS_BASE 0xf8100000 /* PIXIS registers */ #define PIXIS_ID 0x0 /* Board ID at offset 0 */ #define PIXIS_VER 0x1 /* Board version at offset 1 */ #define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */ @@ -204,7 +204,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ #define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ #define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ -#define CFG_PIXIS_VBOOT_MASK 0x40 /* Reset altbank mask*/ +#define CFG_PIXIS_VBOOT_MASK 0x40 /* Reset altbank mask*/ #define CFG_MAX_FLASH_BANKS 2 /* number of banks */ #define CFG_MAX_FLASH_SECT 128 /* sectors per device */ @@ -212,7 +212,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #undef CFG_FLASH_CHECKSUM #define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ #define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ -#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ +#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ #define CFG_FLASH_CFI_DRIVER #define CFG_FLASH_CFI @@ -221,7 +221,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #if (CFG_MONITOR_BASE < CFG_FLASH_BASE) #define CFG_RAMBOOT #else -#undef CFG_RAMBOOT +#undef CFG_RAMBOOT #endif #if defined(CFG_RAMBOOT) @@ -238,32 +238,32 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #else #define CFG_INIT_RAM_ADDR 0xf8400000 /* Initial RAM address */ #endif -#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ +#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ -#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CFG_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CFG_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ /* Serial Port */ #define CONFIG_CONS_INDEX 1 #undef CONFIG_SERIAL_SOFTWARE_FIFO #define CFG_NS16550 #define CFG_NS16550_SERIAL -#define CFG_NS16550_REG_SIZE 1 +#define CFG_NS16550_REG_SIZE 1 #define CFG_NS16550_CLK get_bus_freq(0) #define CFG_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} -#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500) -#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600) +#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500) +#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600) /* Use the HUSH parser */ #define CFG_HUSH_PARSER -#ifdef CFG_HUSH_PARSER +#ifdef CFG_HUSH_PARSER #define CFG_PROMPT_HUSH_PS2 "> " #endif @@ -286,7 +286,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ #define CFG_I2C_SLAVE 0x7F -#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */ +#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */ #define CFG_I2C_OFFSET 0x3100 /* @@ -308,13 +308,13 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */ /* PCI view of System Memory */ -#define CFG_PCI_MEMORY_BUS 0x00000000 -#define CFG_PCI_MEMORY_PHYS 0x00000000 -#define CFG_PCI_MEMORY_SIZE 0x80000000 +#define CFG_PCI_MEMORY_BUS 0x00000000 +#define CFG_PCI_MEMORY_PHYS 0x00000000 +#define CFG_PCI_MEMORY_SIZE 0x80000000 /* For RTL8139 */ #define KSEG1ADDR(x) ({u32 _x=le32_to_cpu(*(u32 *)(x)); (&_x);}) -#define _IO_BASE 0x00000000 +#define _IO_BASE 0x00000000 #define CFG_PCI2_MEM_BASE 0xa0000000 #define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE @@ -325,12 +325,12 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #if defined(CONFIG_PCI) -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ #undef CFG_SCSI_SCAN_BUS_REVERSE #define CONFIG_NET_MULTI -#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_PCI_PNP /* do pci plug-and-play */ #define CONFIG_RTL8139 @@ -340,19 +340,19 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); /************************************************************ * USB support ************************************************************/ -#define CONFIG_PCI_OHCI 1 +#define CONFIG_PCI_OHCI 1 #define CONFIG_USB_OHCI_NEW 1 -#define CONFIG_USB_KEYBOARD 1 +#define CONFIG_USB_KEYBOARD 1 #define CFG_DEVICE_DEREGISTER -#define CFG_USB_EVENT_POLL 1 -#define CFG_USB_OHCI_SLOT_NAME "ohci_pci" -#define CFG_USB_OHCI_MAX_ROOT_PORTS 15 +#define CFG_USB_EVENT_POLL 1 +#define CFG_USB_OHCI_SLOT_NAME "ohci_pci" +#define CFG_USB_OHCI_MAX_ROOT_PORTS 15 #define CFG_OHCI_SWAP_REG_ACCESS 1 #if !defined(CONFIG_PCI_PNP) #define PCI_ENET0_IOADDR 0xe0000000 #define PCI_ENET0_MEMADDR 0xe0000000 - #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ + #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ #endif /*PCIE video card used*/ @@ -384,7 +384,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SATA_ULI5288 #define CFG_SCSI_MAX_SCSI_ID 4 #define CFG_SCSI_MAX_LUN 1 -#define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN) +#define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN) #define CFG_SCSI_MAXDEVICE CFG_SCSI_MAX_DEVICE #endif @@ -395,19 +395,19 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #if defined(CONFIG_TSEC_ENET) #ifndef CONFIG_NET_MULTI -#define CONFIG_NET_MULTI 1 +#define CONFIG_NET_MULTI 1 #endif #define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_TSEC1 1 -#define CONFIG_TSEC1_NAME "eTSEC1" -#define CONFIG_TSEC2 1 -#define CONFIG_TSEC2_NAME "eTSEC2" -#define CONFIG_TSEC3 1 -#define CONFIG_TSEC3_NAME "eTSEC3" -#define CONFIG_TSEC4 1 -#define CONFIG_TSEC4_NAME "eTSEC4" +#define CONFIG_TSEC1 1 +#define CONFIG_TSEC1_NAME "eTSEC1" +#define CONFIG_TSEC2 1 +#define CONFIG_TSEC2_NAME "eTSEC2" +#define CONFIG_TSEC3 1 +#define CONFIG_TSEC3_NAME "eTSEC3" +#define CONFIG_TSEC4 1 +#define CONFIG_TSEC4_NAME "eTSEC4" #define TSEC1_PHY_ADDR 0 #define TSEC2_PHY_ADDR 1 @@ -427,76 +427,76 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #endif /* CONFIG_TSEC_ENET */ /* - * BAT0 2G Cacheable, non-guarded - * 0x0000_0000 2G DDR + * BAT0 2G Cacheable, non-guarded + * 0x0000_0000 2G DDR */ -#define CFG_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) -#define CFG_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP) -#define CFG_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE ) -#define CFG_IBAT0U CFG_DBAT0U +#define CFG_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) +#define CFG_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP) +#define CFG_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE ) +#define CFG_IBAT0U CFG_DBAT0U /* - * BAT1 1G Cache-inhibited, guarded - * 0x8000_0000 512M PCI-Express 1 Memory - * 0xa000_0000 512M PCI-Express 2 Memory + * BAT1 1G Cache-inhibited, guarded + * 0x8000_0000 512M PCI-Express 1 Memory + * 0xa000_0000 512M PCI-Express 2 Memory * Changed it for operating from 0xd0000000 */ -#define CFG_DBAT1L ( CFG_PCI1_MEM_PHYS | BATL_PP_RW \ +#define CFG_DBAT1L ( CFG_PCI1_MEM_PHYS | BATL_PP_RW \ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CFG_DBAT1U (CFG_PCI1_MEM_PHYS | BATU_BL_1G | BATU_VS | BATU_VP) #define CFG_IBAT1L (CFG_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CFG_IBAT1U CFG_DBAT1U +#define CFG_IBAT1U CFG_DBAT1U /* - * BAT2 512M Cache-inhibited, guarded - * 0xc000_0000 512M RapidIO Memory + * BAT2 512M Cache-inhibited, guarded + * 0xc000_0000 512M RapidIO Memory */ -#define CFG_DBAT2L (CFG_RIO_MEM_PHYS | BATL_PP_RW \ +#define CFG_DBAT2L (CFG_RIO_MEM_PHYS | BATL_PP_RW \ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CFG_DBAT2U (CFG_RIO_MEM_PHYS | BATU_BL_512M | BATU_VS | BATU_VP) #define CFG_IBAT2L (CFG_RIO_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CFG_IBAT2U CFG_DBAT2U +#define CFG_IBAT2U CFG_DBAT2U /* - * BAT3 4M Cache-inhibited, guarded - * 0xf800_0000 4M CCSR + * BAT3 4M Cache-inhibited, guarded + * 0xf800_0000 4M CCSR */ -#define CFG_DBAT3L ( CFG_CCSRBAR | BATL_PP_RW \ +#define CFG_DBAT3L ( CFG_CCSRBAR | BATL_PP_RW \ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CFG_DBAT3U (CFG_CCSRBAR | BATU_BL_4M | BATU_VS | BATU_VP) -#define CFG_IBAT3L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CFG_IBAT3U CFG_DBAT3U +#define CFG_DBAT3U (CFG_CCSRBAR | BATU_BL_4M | BATU_VS | BATU_VP) +#define CFG_IBAT3L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CFG_IBAT3U CFG_DBAT3U /* - * BAT4 32M Cache-inhibited, guarded - * 0xe200_0000 16M PCI-Express 1 I/O - * 0xe300_0000 16M PCI-Express 2 I/0 + * BAT4 32M Cache-inhibited, guarded + * 0xe200_0000 16M PCI-Express 1 I/O + * 0xe300_0000 16M PCI-Express 2 I/0 * Note that this is at 0xe0000000 */ -#define CFG_DBAT4L ( CFG_PCI1_IO_PHYS | BATL_PP_RW \ +#define CFG_DBAT4L ( CFG_PCI1_IO_PHYS | BATL_PP_RW \ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CFG_DBAT4U (CFG_PCI1_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP) #define CFG_IBAT4L (CFG_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CFG_IBAT4U CFG_DBAT4U +#define CFG_IBAT4U CFG_DBAT4U /* - * BAT5 128K Cacheable, non-guarded - * 0xe401_0000 128K Init RAM for stack in the CPU DCache (no backing memory) + * BAT5 128K Cacheable, non-guarded + * 0xe401_0000 128K Init RAM for stack in the CPU DCache (no backing memory) */ -#define CFG_DBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE) -#define CFG_DBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) -#define CFG_IBAT5L CFG_DBAT5L -#define CFG_IBAT5U CFG_DBAT5U +#define CFG_DBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE) +#define CFG_DBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) +#define CFG_IBAT5L CFG_DBAT5L +#define CFG_IBAT5U CFG_DBAT5U /* - * BAT6 32M Cache-inhibited, guarded - * 0xfe00_0000 32M FLASH + * BAT6 32M Cache-inhibited, guarded + * 0xfe00_0000 32M FLASH */ -#define CFG_DBAT6L ((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW \ +#define CFG_DBAT6L ((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW \ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CFG_DBAT6U ((CFG_FLASH_BASE & 0xfe000000) | BATU_BL_32M | BATU_VS | BATU_VP) -#define CFG_IBAT6L ((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW | BATL_MEMCOHERENCE) -#define CFG_IBAT6U CFG_DBAT6U +#define CFG_DBAT6U ((CFG_FLASH_BASE & 0xfe000000) | BATU_BL_32M | BATU_VS | BATU_VP) +#define CFG_IBAT6L ((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW | BATL_MEMCOHERENCE) +#define CFG_IBAT6U CFG_DBAT6U #define CFG_DBAT7L 0x00000000 #define CFG_DBAT7U 0x00000000 @@ -557,7 +557,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); * Miscellaneous configurable options */ #define CFG_LONGHELP /* undef to save memory */ -#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ #define CFG_LOAD_ADDR 0x2000000 /* default load address */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */ @@ -598,7 +598,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); /* The mac addresses for all ethernet interface */ #if defined(CONFIG_TSEC_ENET) -#define CONFIG_ETHADDR 00:E0:0C:00:00:01 +#define CONFIG_ETHADDR 00:E0:0C:00:00:01 #define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD #define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD #define CONFIG_ETH3ADDR 00:E0:0C:00:03:FD @@ -624,45 +624,45 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_LOADADDR 1000000 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ -#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ +#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ #define CONFIG_BAUDRATE 115200 -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \ - "tftpflash=tftpboot $loadaddr $uboot; " \ - "protect off " MK_STR(TEXT_BASE) " +$filesize; " \ - "erase " MK_STR(TEXT_BASE) " +$filesize; " \ - "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \ - "protect on " MK_STR(TEXT_BASE) " +$filesize; " \ - "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \ - "consoledev=ttyS0\0" \ - "ramdiskaddr=2000000\0" \ - "ramdiskfile=your.ramdisk.u-boot\0" \ - "fdtaddr=c00000\0" \ - "fdtfile=mpc8641_hpcn.dtb\0" \ - "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \ - "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \ - "maxcpus=2" - - -#define CONFIG_NFSBOOTCOMMAND \ - "setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$serverip:$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_RAMBOOTCOMMAND \ - "setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $ramdiskaddr $ramdiskfile;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \ + "tftpflash=tftpboot $loadaddr $uboot; " \ + "protect off " MK_STR(TEXT_BASE) " +$filesize; " \ + "erase " MK_STR(TEXT_BASE) " +$filesize; " \ + "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \ + "protect on " MK_STR(TEXT_BASE) " +$filesize; " \ + "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=2000000\0" \ + "ramdiskfile=your.ramdisk.u-boot\0" \ + "fdtaddr=c00000\0" \ + "fdtfile=mpc8641_hpcn.dtb\0" \ + "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \ + "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \ + "maxcpus=2" + + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND |