diff options
Diffstat (limited to 'include/configs/MPC8572DS.h')
| -rw-r--r-- | include/configs/MPC8572DS.h | 72 |
1 files changed, 56 insertions, 16 deletions
diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h index 5688589..f98e7fb 100644 --- a/include/configs/MPC8572DS.h +++ b/include/configs/MPC8572DS.h @@ -42,6 +42,7 @@ #define CONFIG_PCIE3 1 /* PCIE controler 3 (ULI bridge) */ #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ +#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ @@ -135,16 +136,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_SYS_DDR_SBE 0x00010000 /* - * FIXME: Not used in fixed_sdram function - */ -#define CONFIG_SYS_DDR_MODE 0x00000022 -#define CONFIG_SYS_DDR_CS1_BNDS 0x00000000 -#define CONFIG_SYS_DDR_CS2_BNDS 0x00000FFF /* Not done */ -#define CONFIG_SYS_DDR_CS3_BNDS 0x00000FFF /* Not done */ -#define CONFIG_SYS_DDR_CS4_BNDS 0x00000FFF /* Not done */ -#define CONFIG_SYS_DDR_CS5_BNDS 0x00000FFF /* Not done */ - -/* * Make sure required options are set */ #ifndef CONFIG_SPD_EEPROM @@ -167,6 +158,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); * Localbus non-cacheable * 0xe000_0000 0xe80f_ffff Promjet/free 128M non-cacheable * 0xe800_0000 0xefff_ffff FLASH 128M non-cacheable + * 0xffa0_0000 0xffaf_ffff NAND 1M non-cacheable * 0xffdf_0000 0xffdf_7fff PIXIS 32K non-cacheable TLB0 * 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0 * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable @@ -269,6 +261,59 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ +#define CONFIG_SYS_NAND_BASE 0xffa00000 +#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE +#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE,\ + CONFIG_SYS_NAND_BASE + 0x40000, \ + CONFIG_SYS_NAND_BASE + 0x80000,\ + CONFIG_SYS_NAND_BASE + 0xC0000} +#define CONFIG_SYS_MAX_NAND_DEVICE 4 +#define NAND_MAX_CHIPS 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE +#define CONFIG_CMD_NAND 1 +#define CONFIG_NAND_FSL_ELBC 1 +#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) + +/* NAND flash config */ +#define CONFIG_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE_PHYS \ + | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ + | BR_PS_8 /* Port Size = 8 bit */ \ + | BR_MS_FCM /* MSEL = FCM */ \ + | BR_V) /* valid */ +#define CONFIG_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \ + | OR_FCM_PGS /* Large Page*/ \ + | OR_FCM_CSCT \ + | OR_FCM_CST \ + | OR_FCM_CHT \ + | OR_FCM_SCY_1 \ + | OR_FCM_TRLX \ + | OR_FCM_EHTR) + +#define CONFIG_SYS_BR2_PRELIM CONFIG_NAND_BR_PRELIM /* NAND Base Address */ +#define CONFIG_SYS_OR2_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ + +#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_NAND_BASE_PHYS + 0x40000)\ + | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ + | BR_PS_8 /* Port Size = 8 bit */ \ + | BR_MS_FCM /* MSEL = FCM */ \ + | BR_V) /* valid */ +#define CONFIG_SYS_OR4_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ +#define CONFIG_SYS_BR5_PRELIM ((CONFIG_SYS_NAND_BASE_PHYS + 0x80000)\ + | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ + | BR_PS_8 /* Port Size = 8 bit */ \ + | BR_MS_FCM /* MSEL = FCM */ \ + | BR_V) /* valid */ +#define CONFIG_SYS_OR5_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ + +#define CONFIG_SYS_BR6_PRELIM ((CONFIG_SYS_NAND_BASE_PHYS + 0xC0000)\ + | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ + | BR_PS_8 /* Port Size = 8 bit */ \ + | BR_MS_FCM /* MSEL = FCM */ \ + | BR_V) /* valid */ +#define CONFIG_SYS_OR6_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ + + + /* Serial Port - controlled on board with jumper J8 * open - index 2 * shorted - index 1 @@ -335,11 +380,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); * Memory space is mapped 1-1, but I/O space must start from 0. */ -/* PCI view of System Memory */ -#define CONFIG_SYS_PCI_MEMORY_BUS 0x00000000 -#define CONFIG_SYS_PCI_MEMORY_PHYS 0x00000000 -#define CONFIG_SYS_PCI_MEMORY_SIZE 0x80000000 - /* controller 3, direct to uli, tgtid 3, Base address 8000 */ #define CONFIG_SYS_PCIE3_MEM_BASE 0x80000000 #define CONFIG_SYS_PCIE3_MEM_PHYS CONFIG_SYS_PCIE3_MEM_BASE @@ -469,7 +509,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #if CONFIG_SYS_MONITOR_BASE > 0xfff80000 #define CONFIG_ENV_ADDR 0xfff80000 #else -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x70000) +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SIZE) #endif #define CONFIG_ENV_SIZE 0x2000 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ |