diff options
Diffstat (limited to 'include/configs/MPC8568MDS.h')
| -rw-r--r-- | include/configs/MPC8568MDS.h | 128 |
1 files changed, 90 insertions, 38 deletions
diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h index 3f65644..ba744e9 100644 --- a/include/configs/MPC8568MDS.h +++ b/include/configs/MPC8568MDS.h @@ -28,20 +28,21 @@ /* High Level Configuration Options */ #define CONFIG_BOOKE 1 /* BOOKE */ -#define CONFIG_E500 1 /* BOOKE e500 family */ +#define CONFIG_E500 1 /* BOOKE e500 family */ #define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48/68 */ #define CONFIG_MPC8568 1 /* MPC8568 specific */ #define CONFIG_MPC8568MDS 1 /* MPC8568MDS board specific */ -#undef CONFIG_PCI +#define CONFIG_PCI #define CONFIG_TSEC_ENET /* tsec ethernet support */ +#define CONFIG_QE /* Enable QE */ #define CONFIG_ENV_OVERWRITE #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ #define CONFIG_DDR_DLL /* possible DLL fix needed */ /*#define CONFIG_DDR_2T_TIMING Sets the 2T timing bit */ /*#define CONFIG_DDR_ECC*/ /* only for ECC DDR module */ -/*#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER*/ /* DDR controller or DMA? */ +/*#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER*/ /* DDR controller or DMA? */ #define CONFIG_MEM_INIT_VALUE 0xDeadBeef @@ -62,9 +63,9 @@ extern unsigned long get_clock_freq(void); /* * These can be toggled for performance analysis, otherwise use default. */ -/*#define CONFIG_L2_CACHE*/ /* toggle L2 cache */ -#define CONFIG_BTB /* toggle branch predition */ -#define CONFIG_ADDR_STREAMING /* toggle addr streaming */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#define CONFIG_BTB /* toggle branch predition */ +#define CONFIG_ADDR_STREAMING /* toggle addr streaming */ /* * Only possible on E500 Version 2 or newer cores. @@ -292,11 +293,9 @@ extern unsigned long get_clock_freq(void); #define CONFIG_OF_FLAT_TREE 1 #define CONFIG_OF_BOARD_SETUP 1 -/* maximum size of the flat tree (8K) */ -#define OF_FLAT_TREE_MAX_SIZE 8192 - #define OF_CPU "PowerPC,8568@0" #define OF_SOC "soc8568@e0000000" +#define OF_QE "qe@e0080000" #define OF_TBCLK (bd->bi_busfreq / 8) #define OF_STDOUT_PATH "/soc8568@e0000000/serial@4600" @@ -306,11 +305,14 @@ extern unsigned long get_clock_freq(void); #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ #define CONFIG_HARD_I2C /* I2C with hardware support*/ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_I2C_CMD_TREE #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_EEPROM_ADDR 0x57 +#define CFG_I2C_EEPROM_ADDR 0x52 #define CFG_I2C_SLAVE 0x7F -#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */ +#define CFG_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */ #define CFG_I2C_OFFSET 0x3000 +#define CFG_I2C2_OFFSET 0x3100 /* * General PCI @@ -318,7 +320,7 @@ extern unsigned long get_clock_freq(void); */ #define CFG_PCI1_MEM_BASE 0x80000000 #define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE -#define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */ +#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */ #define CFG_PCI1_IO_BASE 0x00000000 #define CFG_PCI1_IO_PHYS 0xe2000000 #define CFG_PCI1_IO_SIZE 0x00800000 /* 8M */ @@ -337,6 +339,44 @@ extern unsigned long get_clock_freq(void); #define CONFIG_NET_MULTI #define CONFIG_PCI_PNP /* do pci plug-and-play */ +#ifdef CONFIG_QE +/* + * QE UEC ethernet configuration + */ +#define CONFIG_UEC_ETH +#ifndef CONFIG_TSEC_ENET +#define CONFIG_ETHPRIME "FSL UEC0" +#endif +#define CONFIG_PHY_MODE_NEED_CHANGE +#define CONFIG_eTSEC_MDIO_BUS + +#ifdef CONFIG_eTSEC_MDIO_BUS +#define CONFIG_MIIM_ADDRESS 0xE0024520 +#endif + +#define CONFIG_UEC_ETH1 /* GETH1 */ + +#ifdef CONFIG_UEC_ETH1 +#define CFG_UEC1_UCC_NUM 0 /* UCC1 */ +#define CFG_UEC1_RX_CLK QE_CLK_NONE +#define CFG_UEC1_TX_CLK QE_CLK16 +#define CFG_UEC1_ETH_TYPE GIGA_ETH +#define CFG_UEC1_PHY_ADDR 7 +#define CFG_UEC1_INTERFACE_MODE ENET_1000_GMII +#endif + +#define CONFIG_UEC_ETH2 /* GETH2 */ + +#ifdef CONFIG_UEC_ETH2 +#define CFG_UEC2_UCC_NUM 1 /* UCC2 */ +#define CFG_UEC2_RX_CLK QE_CLK_NONE +#define CFG_UEC2_TX_CLK QE_CLK16 +#define CFG_UEC2_ETH_TYPE GIGA_ETH +#define CFG_UEC2_PHY_ADDR 1 +#define CFG_UEC2_INTERFACE_MODE ENET_1000_GMII +#endif +#endif /* CONFIG_QE */ + #undef CONFIG_EEPRO100 #undef CONFIG_TULIP @@ -345,21 +385,17 @@ extern unsigned long get_clock_freq(void); #endif /* CONFIG_PCI */ - -#if defined(CONFIG_TSEC_ENET) - #ifndef CONFIG_NET_MULTI #define CONFIG_NET_MULTI 1 #endif +#if defined(CONFIG_TSEC_ENET) + #define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_MPC85XX_TSEC1 1 -#define CONFIG_MPC85XX_TSEC1_NAME "eTSEC0" -#define CONFIG_MPC85XX_TSEC2 1 -#define CONFIG_MPC85XX_TSEC2_NAME "eTSEC1" -#undef CONFIG_MPC85XX_TSEC3 -#undef CONFIG_MPC85XX_TSEC4 -#undef CONFIG_MPC85XX_FEC +#define CONFIG_TSEC1 1 +#define CONFIG_TSEC1_NAME "eTSEC0" +#define CONFIG_TSEC2 1 +#define CONFIG_TSEC2_NAME "eTSEC1" #define TSEC1_PHY_ADDR 2 #define TSEC2_PHY_ADDR 3 @@ -367,7 +403,10 @@ extern unsigned long get_clock_freq(void); #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 -/* Options are: eTSEC[0-3] */ +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT + +/* Options are: eTSEC[0-1] */ #define CONFIG_ETHPRIME "eTSEC0" #endif /* CONFIG_TSEC_ENET */ @@ -383,19 +422,29 @@ extern unsigned long get_clock_freq(void); #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII + #if defined(CONFIG_PCI) -#define CONFIG_COMMANDS (CONFIG_CMD_DFL \ - | CFG_CMD_PCI \ - | CFG_CMD_PING \ - | CFG_CMD_I2C \ - | CFG_CMD_MII) -#else -#define CONFIG_COMMANDS (CONFIG_CMD_DFL \ - | CFG_CMD_PING \ - | CFG_CMD_I2C \ - | CFG_CMD_MII) + #define CONFIG_CMD_PCI #endif -#include <cmd_confdefs.h> + #undef CONFIG_WATCHDOG /* watchdog disabled */ @@ -405,7 +454,7 @@ extern unsigned long get_clock_freq(void); #define CFG_LONGHELP /* undef to save memory */ #define CFG_LOAD_ADDR 0x2000000 /* default load address */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ @@ -425,7 +474,7 @@ extern unsigned long get_clock_freq(void); /* Cache Configuration */ #define CFG_DCACHE_SIZE 32768 #define CFG_CACHELINE_SIZE 32 -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ #endif @@ -437,7 +486,7 @@ extern unsigned long get_clock_freq(void); #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif @@ -447,12 +496,15 @@ extern unsigned long get_clock_freq(void); */ /* The mac addresses for all ethernet interface */ -#if defined(CONFIG_TSEC_ENET) +#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_UEC_ETH) +#define CONFIG_HAS_ETH0 #define CONFIG_ETHADDR 00:E0:0C:00:00:FD #define CONFIG_HAS_ETH1 #define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD #define CONFIG_HAS_ETH2 #define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD +#define CONFIG_HAS_ETH3 +#define CONFIG_ETH3ADDR 00:E0:0C:00:03:FD #endif #define CONFIG_IPADDR 192.168.1.253 |