diff options
Diffstat (limited to 'include/configs/MPC8568MDS.h')
| -rw-r--r-- | include/configs/MPC8568MDS.h | 278 |
1 files changed, 137 insertions, 141 deletions
diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h index 8aeaa29..da1f454 100644 --- a/include/configs/MPC8568MDS.h +++ b/include/configs/MPC8568MDS.h @@ -38,6 +38,7 @@ #define CONFIG_PCIE1 1 /* PCIE controller */ #define CONFIG_FSL_PCI_INIT 1 /* use common fsl pci init code */ #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ +#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_QE /* Enable QE */ #define CONFIG_ENV_OVERWRITE @@ -60,7 +61,6 @@ extern unsigned long get_clock_freq(void); */ #define CONFIG_L2_CACHE /* toggle L2 cache */ #define CONFIG_BTB /* toggle branch predition */ -#define CONFIG_ADDR_STREAMING /* toggle addr streaming */ /* * Only possible on E500 Version 2 or newer cores. @@ -70,20 +70,20 @@ extern unsigned long get_clock_freq(void); #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ -#define CFG_MEMTEST_START 0x00200000 /* memtest works on */ -#define CFG_MEMTEST_END 0x00400000 +#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00400000 /* * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) */ -#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ -#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ -#define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */ -#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ +#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ +#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ -#define CFG_PCI1_ADDR (CFG_CCSRBAR+0x8000) -#define CFG_PCIE1_ADDR (CFG_CCSRBAR+0xa000) +#define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR+0x8000) +#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000) /* DDR Setup */ #define CONFIG_FSL_DDR2 @@ -91,12 +91,12 @@ extern unsigned long get_clock_freq(void); #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ #define CONFIG_DDR_SPD #define CONFIG_DDR_DLL /* possible DLL fix needed */ -#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ #define CONFIG_MEM_INIT_VALUE 0xDeadBeef -#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ -#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE #define CONFIG_NUM_DDR_CONTROLLERS 1 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 @@ -145,70 +145,70 @@ extern unsigned long get_clock_freq(void); * 0 4 8 12 16 20 24 28 * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 ORx */ -#define CFG_BCSR_BASE 0xf8000000 +#define CONFIG_SYS_BCSR_BASE 0xf8000000 -#define CFG_FLASH_BASE 0xfe000000 /* start of FLASH 32M */ +#define CONFIG_SYS_FLASH_BASE 0xfe000000 /* start of FLASH 32M */ /*Chip select 0 - Flash*/ -#define CFG_BR0_PRELIM 0xfe001001 -#define CFG_OR0_PRELIM 0xfe006ff7 +#define CONFIG_SYS_BR0_PRELIM 0xfe001001 +#define CONFIG_SYS_OR0_PRELIM 0xfe006ff7 /*Chip slelect 1 - BCSR*/ -#define CFG_BR1_PRELIM 0xf8000801 -#define CFG_OR1_PRELIM 0xffffe9f7 +#define CONFIG_SYS_BR1_PRELIM 0xf8000801 +#define CONFIG_SYS_OR1_PRELIM 0xffffe9f7 -/*#define CFG_FLASH_BANKS_LIST {0xff800000, CFG_FLASH_BASE} */ -#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ -#define CFG_MAX_FLASH_SECT 512 /* sectors per device */ -#undef CFG_FLASH_CHECKSUM -#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ +/*#define CONFIG_SYS_FLASH_BANKS_LIST {0xff800000, CONFIG_SYS_FLASH_BASE} */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */ +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ -#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ #define CONFIG_FLASH_CFI_DRIVER -#define CFG_FLASH_CFI -#define CFG_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_EMPTY_INFO /* * SDRAM on the LocalBus */ -#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ -#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ +#define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ +#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ /*Chip select 2 - SDRAM*/ -#define CFG_BR2_PRELIM 0xf0001861 -#define CFG_OR2_PRELIM 0xfc006901 +#define CONFIG_SYS_BR2_PRELIM 0xf0001861 +#define CONFIG_SYS_OR2_PRELIM 0xfc006901 -#define CFG_LBC_LCRR 0x00030004 /* LB clock ratio reg */ -#define CFG_LBC_LBCR 0x00000000 /* LB config reg */ -#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ -#define CFG_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/ +#define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */ +#define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ +#define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ +#define CONFIG_SYS_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/ /* * LSDMR masks */ -#define CFG_LBC_LSDMR_RFEN (1 << (31 - 1)) -#define CFG_LBC_LSDMR_BSMA1516 (3 << (31 - 10)) -#define CFG_LBC_LSDMR_BSMA1617 (4 << (31 - 10)) -#define CFG_LBC_LSDMR_RFCR16 (7 << (31 - 16)) -#define CFG_LBC_LSDMR_PRETOACT7 (7 << (31 - 19)) -#define CFG_LBC_LSDMR_ACTTORW7 (7 << (31 - 22)) -#define CFG_LBC_LSDMR_ACTTORW6 (6 << (31 - 22)) -#define CFG_LBC_LSDMR_BL8 (1 << (31 - 23)) -#define CFG_LBC_LSDMR_WRC4 (0 << (31 - 27)) -#define CFG_LBC_LSDMR_CL3 (3 << (31 - 31)) - -#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4)) -#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4)) -#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4)) -#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4)) -#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4)) -#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4)) -#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4)) -#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4)) +#define CONFIG_SYS_LBC_LSDMR_RFEN (1 << (31 - 1)) +#define CONFIG_SYS_LBC_LSDMR_BSMA1516 (3 << (31 - 10)) +#define CONFIG_SYS_LBC_LSDMR_BSMA1617 (4 << (31 - 10)) +#define CONFIG_SYS_LBC_LSDMR_RFCR16 (7 << (31 - 16)) +#define CONFIG_SYS_LBC_LSDMR_PRETOACT7 (7 << (31 - 19)) +#define CONFIG_SYS_LBC_LSDMR_ACTTORW7 (7 << (31 - 22)) +#define CONFIG_SYS_LBC_LSDMR_ACTTORW6 (6 << (31 - 22)) +#define CONFIG_SYS_LBC_LSDMR_BL8 (1 << (31 - 23)) +#define CONFIG_SYS_LBC_LSDMR_WRC4 (0 << (31 - 27)) +#define CONFIG_SYS_LBC_LSDMR_CL3 (3 << (31 - 31)) + +#define CONFIG_SYS_LBC_LSDMR_OP_NORMAL (0 << (31 - 4)) +#define CONFIG_SYS_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4)) +#define CONFIG_SYS_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4)) +#define CONFIG_SYS_LBC_LSDMR_OP_MRW (3 << (31 - 4)) +#define CONFIG_SYS_LBC_LSDMR_OP_PRECH (4 << (31 - 4)) +#define CONFIG_SYS_LBC_LSDMR_OP_PCHALL (5 << (31 - 4)) +#define CONFIG_SYS_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4)) +#define CONFIG_SYS_LBC_LSDMR_OP_RWINV (7 << (31 - 4)) /* * Common settings for all Local Bus SDRAM commands. @@ -216,13 +216,13 @@ extern unsigned long get_clock_freq(void); * or BSMA1617 (for CPU 1.0) (old) * is OR'ed in too. */ -#define CFG_LBC_LSDMR_COMMON ( CFG_LBC_LSDMR_RFCR16 \ - | CFG_LBC_LSDMR_PRETOACT7 \ - | CFG_LBC_LSDMR_ACTTORW7 \ - | CFG_LBC_LSDMR_BL8 \ - | CFG_LBC_LSDMR_WRC4 \ - | CFG_LBC_LSDMR_CL3 \ - | CFG_LBC_LSDMR_RFEN \ +#define CONFIG_SYS_LBC_LSDMR_COMMON ( CONFIG_SYS_LBC_LSDMR_RFCR16 \ + | CONFIG_SYS_LBC_LSDMR_PRETOACT7 \ + | CONFIG_SYS_LBC_LSDMR_ACTTORW7 \ + | CONFIG_SYS_LBC_LSDMR_BL8 \ + | CONFIG_SYS_LBC_LSDMR_WRC4 \ + | CONFIG_SYS_LBC_LSDMR_CL3 \ + | CONFIG_SYS_LBC_LSDMR_RFEN \ ) /* @@ -254,46 +254,45 @@ extern unsigned long get_clock_freq(void); * 0 4 8 12 16 20 24 28 * 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7 */ -#define CFG_BCSR (0xf8000000) +#define CONFIG_SYS_BCSR (0xf8000000) /*Chip slelect 4 - PIB*/ -#define CFG_BR4_PRELIM 0xf8008801 -#define CFG_OR4_PRELIM 0xffffe9f7 +#define CONFIG_SYS_BR4_PRELIM 0xf8008801 +#define CONFIG_SYS_OR4_PRELIM 0xffffe9f7 /*Chip select 5 - PIB*/ -#define CFG_BR5_PRELIM 0xf8010801 -#define CFG_OR5_PRELIM 0xffff69f7 +#define CONFIG_SYS_BR5_PRELIM 0xf8010801 +#define CONFIG_SYS_OR5_PRELIM 0xffff69f7 -#define CONFIG_L1_INIT_RAM -#define CFG_INIT_RAM_LOCK 1 -#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ -#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in RAM */ -#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ /* Serial Port */ #define CONFIG_CONS_INDEX 1 #undef CONFIG_SERIAL_SOFTWARE_FIFO -#define CFG_NS16550 -#define CFG_NS16550_SERIAL -#define CFG_NS16550_REG_SIZE 1 -#define CFG_NS16550_CLK get_bus_freq(0) +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) -#define CFG_BAUDRATE_TABLE \ +#define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} -#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500) -#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600) +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) /* Use the HUSH parser*/ -#define CFG_HUSH_PARSER -#ifdef CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_HUSH_PARSER +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #endif /* pass open firmware flat tree */ @@ -301,8 +300,8 @@ extern unsigned long get_clock_freq(void); #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 -#define CFG_64BIT_VSPRINTF 1 -#define CFG_64BIT_STRTOUL 1 +#define CONFIG_SYS_64BIT_VSPRINTF 1 +#define CONFIG_SYS_64BIT_STRTOUL 1 /* * I2C @@ -312,32 +311,32 @@ extern unsigned long get_clock_freq(void); #undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CONFIG_I2C_MULTI_BUS #define CONFIG_I2C_CMD_TREE -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_EEPROM_ADDR 0x52 -#define CFG_I2C_SLAVE 0x7F -#define CFG_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */ -#define CFG_I2C_OFFSET 0x3000 -#define CFG_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */ +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C2_OFFSET 0x3100 /* * General PCI * Memory Addresses are mapped 1-1. I/O is mapped from 0 */ -#define CFG_PCI1_MEM_BASE 0x80000000 -#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE -#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */ -#define CFG_PCI1_IO_BASE 0x00000000 -#define CFG_PCI1_IO_PHYS 0xe2000000 -#define CFG_PCI1_IO_SIZE 0x00800000 /* 8M */ - -#define CFG_PCIE1_MEM_BASE 0xa0000000 -#define CFG_PCIE1_MEM_PHYS CFG_PCIE1_MEM_BASE -#define CFG_PCIE1_MEM_SIZE 0x20000000 /* 512M */ -#define CFG_PCIE1_IO_BASE 0x00000000 -#define CFG_PCIE1_IO_PHYS 0xe2800000 -#define CFG_PCIE1_IO_SIZE 0x00800000 /* 8M */ - -#define CFG_SRIO_MEM_BASE 0xc0000000 +#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 +#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE +#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCI1_IO_BASE 0x00000000 +#define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000 +#define CONFIG_SYS_PCI1_IO_SIZE 0x00800000 /* 8M */ + +#define CONFIG_SYS_PCIE1_MEM_BASE 0xa0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BASE +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xe2800000 +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ + +#define CONFIG_SYS_SRIO_MEM_BASE 0xc0000000 #ifdef CONFIG_QE /* @@ -357,23 +356,23 @@ extern unsigned long get_clock_freq(void); #define CONFIG_UEC_ETH1 /* GETH1 */ #ifdef CONFIG_UEC_ETH1 -#define CFG_UEC1_UCC_NUM 0 /* UCC1 */ -#define CFG_UEC1_RX_CLK QE_CLK_NONE -#define CFG_UEC1_TX_CLK QE_CLK16 -#define CFG_UEC1_ETH_TYPE GIGA_ETH -#define CFG_UEC1_PHY_ADDR 7 -#define CFG_UEC1_INTERFACE_MODE ENET_1000_GMII +#define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */ +#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE +#define CONFIG_SYS_UEC1_TX_CLK QE_CLK16 +#define CONFIG_SYS_UEC1_ETH_TYPE GIGA_ETH +#define CONFIG_SYS_UEC1_PHY_ADDR 7 +#define CONFIG_SYS_UEC1_INTERFACE_MODE ENET_1000_RGMII_ID #endif #define CONFIG_UEC_ETH2 /* GETH2 */ #ifdef CONFIG_UEC_ETH2 -#define CFG_UEC2_UCC_NUM 1 /* UCC2 */ -#define CFG_UEC2_RX_CLK QE_CLK_NONE -#define CFG_UEC2_TX_CLK QE_CLK16 -#define CFG_UEC2_ETH_TYPE GIGA_ETH -#define CFG_UEC2_PHY_ADDR 1 -#define CFG_UEC2_INTERFACE_MODE ENET_1000_GMII +#define CONFIG_SYS_UEC2_UCC_NUM 1 /* UCC2 */ +#define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE +#define CONFIG_SYS_UEC2_TX_CLK QE_CLK16 +#define CONFIG_SYS_UEC2_ETH_TYPE GIGA_ETH +#define CONFIG_SYS_UEC2_PHY_ADDR 1 +#define CONFIG_SYS_UEC2_INTERFACE_MODE ENET_1000_RGMII_ID #endif #endif /* CONFIG_QE */ @@ -386,12 +385,7 @@ extern unsigned long get_clock_freq(void); #undef CONFIG_TULIP #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ - -/* PCI view of System Memory */ -#define CFG_PCI_MEMORY_BUS 0x00000000 -#define CFG_PCI_MEMORY_PHYS 0x00000000 -#define CFG_PCI_MEMORY_SIZE 0x80000000 +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ #endif /* CONFIG_PCI */ @@ -424,13 +418,13 @@ extern unsigned long get_clock_freq(void); /* * Environment */ -#define CFG_ENV_IS_IN_FLASH 1 -#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) -#define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ -#define CFG_ENV_SIZE 0x2000 +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) +#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ +#define CONFIG_ENV_SIZE 0x2000 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ /* @@ -451,6 +445,8 @@ extern unsigned long get_clock_freq(void); #define CONFIG_CMD_I2C #define CONFIG_CMD_MII #define CONFIG_CMD_ELF +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_SETEXPR #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI @@ -462,26 +458,26 @@ extern unsigned long get_clock_freq(void); /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_CMDLINE_EDITING /* Command-line editing */ -#define CFG_LOAD_ADDR 0x2000000 /* default load address */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ /* * Internal Definitions |