diff options
Diffstat (limited to 'include/configs/MPC8541CDS.h')
| -rw-r--r-- | include/configs/MPC8541CDS.h | 65 |
1 files changed, 53 insertions, 12 deletions
diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h index 3dd4957..c96b98b 100644 --- a/include/configs/MPC8541CDS.h +++ b/include/configs/MPC8541CDS.h @@ -33,6 +33,7 @@ #define CONFIG_BOOKE 1 /* BOOKE */ #define CONFIG_E500 1 /* BOOKE e500 family */ #define CONFIG_MPC85xx 1 /* MPC8540/60/55/41 */ +#define CONFIG_CPM2 1 /* has CPM2 */ #define CONFIG_MPC8541 1 /* MPC8541 specific */ #define CONFIG_MPC8541CDS 1 /* MPC8541CDS board specific */ @@ -40,9 +41,12 @@ #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_ENV_OVERWRITE #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ -#define CONFIG_DDR_ECC /* only for ECC DDR module */ #define CONFIG_DDR_DLL /* possible DLL fix needed */ -#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ +#undef CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ + +#define CONFIG_DDR_ECC /* only for ECC DDR module */ +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef + /* * When initializing flash, if we cannot find the manufacturer ID, @@ -94,18 +98,50 @@ extern unsigned long get_clock_freq(void); #error ("CONFIG_SPD_EEPROM is required by MPC85555CDS") #endif +#undef CONFIG_CLOCKS_IN_MHZ + + /* - * SDRAM on the Local Bus + * Local Bus Definitions */ -#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ -#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ + +/* + * FLASH on the Local Bus + * Two banks, 8M each, using the CFI driver. + * Boot from BR0/OR0 bank at 0xff00_0000 + * Alternate BR1/OR1 bank at 0xff80_0000 + * + * BR0, BR1: + * Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0 + * Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0 + * Port Size = 16 bits = BRx[19:20] = 10 + * Use GPCM = BRx[24:26] = 000 + * Valid = BRx[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001 BR0 + * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001 BR1 + * + * OR0, OR1: + * Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0 + * Reserved ORx[17:18] = 11, confusion here? + * CSNT = ORx[20] = 1 + * ACS = half cycle delay = ORx[21:22] = 11 + * SCY = 6 = ORx[24:27] = 0110 + * TRLX = use relaxed timing = ORx[29] = 1 + * EAD = use external address latch delay = OR[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 ORx + */ + #define CFG_FLASH_BASE 0xff000000 /* start of FLASH 8M */ -#define CFG_BR0_PRELIM 0xff801001 /* port size 16bit */ -#define CFG_BR1_PRELIM 0xff001001 /* port size 16bit */ +#define CFG_BR0_PRELIM 0xff801001 +#define CFG_BR1_PRELIM 0xff001001 -#define CFG_OR0_PRELIM 0xff806e61 /* 8MB Flash */ -#define CFG_OR1_PRELIM 0xff806e61 /* 8MB Flash */ +#define CFG_OR0_PRELIM 0xff806e65 +#define CFG_OR1_PRELIM 0xff806e65 #define CFG_FLASH_BANKS_LIST {0xff800000, CFG_FLASH_BASE} #define CFG_MAX_FLASH_BANKS 2 /* number of banks */ @@ -120,11 +156,12 @@ extern unsigned long get_clock_freq(void); #define CFG_FLASH_CFI #define CFG_FLASH_EMPTY_INFO -#undef CONFIG_CLOCKS_IN_MHZ /* - * Local Bus Definitions + * SDRAM on the Local Bus */ +#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ +#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ /* * Base Register 2 and Option Register 2 configure SDRAM. @@ -326,7 +363,9 @@ extern unsigned long get_clock_freq(void); #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_MPC85XX_TSEC1 1 +#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0" #define CONFIG_MPC85XX_TSEC2 1 +#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1" #undef CONFIG_MPC85XX_FEC #define TSEC1_PHY_ADDR 0 #define TSEC2_PHY_ADDR 1 @@ -334,7 +373,9 @@ extern unsigned long get_clock_freq(void); #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 #define FEC_PHYIDX 0 -#define CONFIG_ETHPRIME "MOTO ENET0" + +/* Options are: TSEC[0-1] */ +#define CONFIG_ETHPRIME "TSEC0" #endif /* CONFIG_TSEC_ENET */ |