summaryrefslogtreecommitdiff
path: root/include/configs/MPC8540ADS.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs/MPC8540ADS.h')
-rw-r--r--include/configs/MPC8540ADS.h148
1 files changed, 74 insertions, 74 deletions
diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h
index 951d1fe..2f1bb48 100644
--- a/include/configs/MPC8540ADS.h
+++ b/include/configs/MPC8540ADS.h
@@ -31,21 +31,21 @@
#define __CONFIG_H
/* High Level Configuration Options */
-#define CONFIG_BOOKE 1 /* BOOKE */
+#define CONFIG_BOOKE 1 /* BOOKE */
#define CONFIG_E500 1 /* BOOKE e500 family */
#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */
-#define CONFIG_MPC85xx_REV1 1 /* MPC85xx Rev 1 Chip */
-#define CONFIG_MPC8540 1 /* MPC8540 specific */
+#define CONFIG_MPC85xx_REV1 1 /* MPC85xx Rev 1 Chip */
+#define CONFIG_MPC8540 1 /* MPC8540 specific */
#define CONFIG_MPC8540ADS 1 /* MPC8540ADS board specific*/
-#undef CONFIG_PCI /* pci ethernet support */
-#define CONFIG_TSEC_ENET /* tsec ethernet support */
+#undef CONFIG_PCI /* pci ethernet support */
+#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
-#undef CONFIG_DDR_ECC /* only for ECC DDR module */
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
+#undef CONFIG_DDR_ECC /* only for ECC DDR module */
#if defined(CONFIG_MPC85xx_REV1)
-#define CONFIG_DDR_DLL /* possible DLL fix needed */
+#define CONFIG_DDR_DLL /* possible DLL fix needed */
#endif
/* Using Localbus SDRAM to emulate flash before we can program the flash,
@@ -53,24 +53,24 @@
*/
#undef CONFIG_RAM_AS_FLASH
-#if !defined(CONFIG_PCI) /* some PCI card is 33Mhz only */
+#if !defined(CONFIG_PCI) /* some PCI card is 33Mhz only */
#define CONFIG_SYS_CLK_FREQ 66000000 /* sysclk for MPC85xx */
#else
#define CONFIG_SYS_CLK_FREQ 33000000 /* most pci cards are 33Mhz */
#endif
-#if !defined(CONFIG_SPD_EEPROM) /* manually set up DDR parameters */
+#if !defined(CONFIG_SPD_EEPROM) /* manually set up DDR parameters */
#define CONFIG_DDR_SETTING
#endif
/* below can be toggled for performance analysis. otherwise use default */
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#undef CONFIG_BTB /* toggle branch predition */
-#undef CONFIG_ADDR_STREAMING /* toggle addr streaming */
+#define CONFIG_L2_CACHE /* toggle L2 cache */
+#undef CONFIG_BTB /* toggle branch predition */
+#undef CONFIG_ADDR_STREAMING /* toggle addr streaming */
-#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
-#undef CFG_DRAM_TEST /* memory test, takes time */
+#undef CFG_DRAM_TEST /* memory test, takes time */
#define CFG_MEMTEST_START 0x00200000 /* memtest works on */
#define CFG_MEMTEST_END 0x00400000
@@ -82,13 +82,13 @@
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
-#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
-#define CFG_CCSRBAR 0xfdf00000 /* relocated CCSRBAR */
+#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CFG_CCSRBAR 0xfdf00000 /* relocated CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
-#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */
+#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */
#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
-#define CFG_SDRAM_SIZE 128 /* DDR is now 128MB */
+#define CFG_SDRAM_SIZE 128 /* DDR is now 128MB */
#if defined(CONFIG_RAM_AS_FLASH)
#define CFG_LBC_SDRAM_BASE 0xfc000000 /* Localbus SDRAM */
@@ -98,44 +98,44 @@
#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
#if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_FLASH_BASE 0xf8000000 /* start of FLASH 16M */
+#define CFG_FLASH_BASE 0xf8000000 /* start of FLASH 16M */
#define CFG_BR0_PRELIM 0xf8001801 /* port size 32bit */
#else /* Boot from real Flash */
-#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */
+#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */
#define CFG_BR0_PRELIM 0xff001801 /* port size 32bit */
#endif
-#define CFG_OR0_PRELIM 0xff006ff7 /* 16MB Flash */
+#define CFG_OR0_PRELIM 0xff006ff7 /* 16MB Flash */
#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
-#define CFG_MAX_FLASH_SECT 64 /* sectors per device */
+#define CFG_MAX_FLASH_SECT 64 /* sectors per device */
#undef CFG_FLASH_CHECKSUM
#define CFG_FLASH_ERASE_TOUT 60000 /* Timeout for Flash Erase (in ms)*/
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms)*/
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
#define CFG_RAMBOOT
#else
-#undef CFG_RAMBOOT
+#undef CFG_RAMBOOT
#endif
#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
#if defined(CONFIG_DDR_SETTING)
-#define CFG_DDR_CS0_BNDS 0x00000007 /* 0-128MB */
-#define CFG_DDR_CS0_CONFIG 0x80000002
-#define CFG_DDR_TIMING_1 0x37344321
-#define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning*/
-#define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR*/
-#define CFG_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */
-#define CFG_DDR_INTERVAL 0x05200100 /* autocharge,no open page*/
+#define CFG_DDR_CS0_BNDS 0x00000007 /* 0-128MB */
+#define CFG_DDR_CS0_CONFIG 0x80000002
+#define CFG_DDR_TIMING_1 0x37344321
+#define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning*/
+#define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR*/
+#define CFG_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */
+#define CFG_DDR_INTERVAL 0x05200100 /* autocharge,no open page*/
#endif
#undef CONFIG_CLOCKS_IN_MHZ
/* local bus definitions */
-#define CFG_BR2_PRELIM 0xf8001861 /* 64MB localbus SDRAM */
+#define CFG_BR2_PRELIM 0xf8001861 /* 64MB localbus SDRAM */
#define CFG_OR2_PRELIM 0xfc006901
#define CFG_LBC_LCRR 0x00030004 /* local bus freq divider*/
#define CFG_LBC_LBCR 0x00000000
@@ -148,52 +148,52 @@
#define CFG_LBC_LSDMR_5 0x4061b723
#if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */
+#define CFG_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */
#else
-#define CFG_BR4_PRELIM 0xfc000801 /* 32KB, 8-bit wide for ADS config reg */
+#define CFG_BR4_PRELIM 0xfc000801 /* 32KB, 8-bit wide for ADS config reg */
#endif
-#define CFG_OR4_PRELIM 0xffffe1f1
-#define CFG_BCSR (CFG_BR4_PRELIM & 0xffff8000)
+#define CFG_OR4_PRELIM 0xffffe1f1
+#define CFG_BCSR (CFG_BR4_PRELIM & 0xffff8000)
#define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0x40000000 /* Initial RAM address */
-#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
+#define CFG_INIT_RAM_LOCK 1
+#define CFG_INIT_RAM_ADDR 0x40000000 /* Initial RAM address */
+#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/* Serial Port */
#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CFG_NS16550
#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE 1
+#define CFG_NS16550_REG_SIZE 1
#define CFG_NS16550_CLK get_bus_freq(0)
-#define CONFIG_BAUDRATE 115200
+#define CONFIG_BAUDRATE 115200
#define CFG_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
-#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
+#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
+#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
/* Use the HUSH parser */
#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
+#ifdef CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
/* General PCI */
#define CFG_PCI_MEM_BASE 0xe0000000
@@ -203,22 +203,22 @@
#define CONFIG_NET_MULTI
#undef CONFIG_EEPRO100
#define CONFIG_TULIP
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
#if !defined(CONFIG_PCI_PNP)
- #define PCI_ENET0_IOADDR 0xe0000000
- #define PCI_ENET0_MEMADDR 0xe0000000
- #define PCI_IDSEL_NUMBER 0x0c /*slot0->3(IDSEL)=12->15*/
+ #define PCI_ENET0_IOADDR 0xe0000000
+ #define PCI_ENET0_MEMADDR 0xe0000000
+ #define PCI_IDSEL_NUMBER 0x0c /*slot0->3(IDSEL)=12->15*/
#endif
-#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
+#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
+#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
#if defined(CONFIG_MPC85xx_REV1) /* Errata PCI 8 */
#define CFG_PCI_SUBSYS_DEVICEID 0x0003
#else
#define CFG_PCI_SUBSYS_DEVICEID 0x0008
#endif
#elif defined(CONFIG_TSEC_ENET)
-#define CONFIG_NET_MULTI 1
-#define CONFIG_PHY_M88E1011 1 /* GigaBit Ether PHY */
+#define CONFIG_NET_MULTI 1
+#define CONFIG_PHY_M88E1011 1 /* GigaBit Ether PHY */
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 8 /* PHY address */
#endif
@@ -232,7 +232,7 @@
#else
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
- #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
+ #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
#endif
#define CFG_ENV_SIZE 0x2000
#else
@@ -242,10 +242,10 @@
#define CFG_ENV_SIZE 0x2000
#endif
-#define CONFIG_BOOTARGS "root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8540ads-003:eth0:off console=ttyS0,115200"
+#define CONFIG_BOOTARGS "root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8540ads-003:eth0:off console=ttyS0,115200"
/*#define CONFIG_BOOTARGS "root=/dev/ram rw console=ttyS0,115200"*/
#define CONFIG_BOOTCOMMAND "bootm 0xff300000 0xff700000"
-#define CONFIG_BOOTDELAY 3 /* -1 disable autoboot */
+#define CONFIG_BOOTDELAY 3 /* -1 disable autoboot */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
@@ -274,7 +274,7 @@
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "MPC8540ADS=> " /* Monitor Command Prompt */
+#define CFG_PROMPT "MPC8540ADS=> " /* Monitor Command Prompt */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
@@ -291,10 +291,10 @@
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/* Cache Configuration */
-#define CFG_DCACHE_SIZE 32768
+#define CFG_DCACHE_SIZE 32768
#define CFG_CACHELINE_SIZE 32
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
@@ -315,17 +315,17 @@
/* NOTE: change below for your network setting!!! */
#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_ETHADDR 00:01:af:07:9b:8a
-#define CONFIG_ETH1ADDR 00:01:af:07:9b:8b
-#define CONFIG_ETH2ADDR 00:01:af:07:9b:8c
+#define CONFIG_ETHADDR 00:01:af:07:9b:8a
+#define CONFIG_ETH1ADDR 00:01:af:07:9b:8b
+#define CONFIG_ETH2ADDR 00:01:af:07:9b:8c
#endif
-#define CONFIG_SERVERIP 163.12.64.52
-#define CONFIG_IPADDR 10.82.0.105
-#define CONFIG_GATEWAYIP 10.82.1.254
-#define CONFIG_NETMASK 255.255.254.0
-#define CONFIG_HOSTNAME MPC8560ADS_PILOT_003
-#define CONFIG_ROOTPATH /home/r6aads/mpclinux/eldk-2.0.2/ppc_82xx
-#define CONFIG_BOOTFILE pImage
+#define CONFIG_SERVERIP 163.12.64.52
+#define CONFIG_IPADDR 10.82.0.105
+#define CONFIG_GATEWAYIP 10.82.1.254
+#define CONFIG_NETMASK 255.255.254.0
+#define CONFIG_HOSTNAME MPC8560ADS_PILOT_003
+#define CONFIG_ROOTPATH /home/r6aads/mpclinux/eldk-2.0.2/ppc_82xx
+#define CONFIG_BOOTFILE pImage
#endif /* __CONFIG_H */