diff options
Diffstat (limited to 'include/configs/MPC8360ERDK.h')
| -rw-r--r-- | include/configs/MPC8360ERDK.h | 620 |
1 files changed, 0 insertions, 620 deletions
diff --git a/include/configs/MPC8360ERDK.h b/include/configs/MPC8360ERDK.h deleted file mode 100644 index 1b8bad1..0000000 --- a/include/configs/MPC8360ERDK.h +++ /dev/null @@ -1,620 +0,0 @@ -/* - * Copyright (C) 2006 Freescale Semiconductor, Inc. - * Dave Liu <daveliu@freescale.com> - * - * Copyright (C) 2007 Logic Product Development, Inc. - * Peter Barada <peterb@logicpd.com> - * - * Copyright (C) 2007 MontaVista Software, Inc. - * Anton Vorontsov <avorontsov@ru.mvista.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ -#define CONFIG_E300 1 /* E300 family */ -#define CONFIG_QE 1 /* Has QE */ -#define CONFIG_MPC8360 1 /* MPC8360 CPU specific */ -#define CONFIG_MPC8360ERDK 1 /* MPC8360ERDK board specific */ - -#define CONFIG_SYS_TEXT_BASE 0xFF800000 - -/* - * System Clock Setup - */ -#ifdef CONFIG_CLKIN_33MHZ -#define CONFIG_83XX_CLKIN 33333333 -#define CONFIG_SYS_CLK_FREQ 33333333 -#define CONFIG_PCI_33M 1 -#define HRCWL_CSB_TO_CLKIN_MPC8360ERDK HRCWL_CSB_TO_CLKIN_10X1 -#else -#define CONFIG_83XX_CLKIN 66000000 -#define CONFIG_SYS_CLK_FREQ 66000000 -#define CONFIG_PCI_66M 1 -#define HRCWL_CSB_TO_CLKIN_MPC8360ERDK HRCWL_CSB_TO_CLKIN_5X1 -#endif /* CONFIG_CLKIN_33MHZ */ - -/* - * Hardware Reset Configuration Word - */ -#define CONFIG_SYS_HRCW_LOW (\ - HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ - HRCWL_DDR_TO_SCB_CLK_1X1 |\ - HRCWL_CSB_TO_CLKIN_MPC8360ERDK |\ - HRCWL_CORE_TO_CSB_2X1 |\ - HRCWL_CE_TO_PLL_1X15) - -#define CONFIG_SYS_HRCW_HIGH (\ - HRCWH_PCI_HOST |\ - HRCWH_PCI1_ARBITER_ENABLE |\ - HRCWH_PCICKDRV_ENABLE |\ - HRCWH_CORE_ENABLE |\ - HRCWH_FROM_0X00000100 |\ - HRCWH_BOOTSEQ_DISABLE |\ - HRCWH_SW_WATCHDOG_DISABLE |\ - HRCWH_ROM_LOC_LOCAL_16BIT |\ - HRCWH_SECONDARY_DDR_DISABLE |\ - HRCWH_BIG_ENDIAN |\ - HRCWH_LALE_EARLY) - -/* - * System IO Config - */ -#define CONFIG_SYS_SICRH 0x00000000 -#define CONFIG_SYS_SICRL 0x40000000 - -#define CONFIG_BOARD_EARLY_INIT_R - -/* - * IMMR new address - */ -#define CONFIG_SYS_IMMR 0xE0000000 - -/* - * DDR Setup - */ -#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE -#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE -#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \ - | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) - -#define CONFIG_SYS_83XX_DDR_USES_CS0 - -#define CONFIG_DDR_ECC /* support DDR ECC function */ -#define CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */ - -/* - * DDRCDR - DDR Control Driver Register - */ -#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_DHC_EN \ - | DDRCDR_ODT \ - | DDRCDR_Q_DRN) - /* 0x80080001 */ - -#undef CONFIG_SPD_EEPROM /* Do not use SPD EEPROM for DDR setup */ - -/* - * Manually set up DDR parameters - */ -#define CONFIG_DDR_II -#define CONFIG_SYS_DDR_SIZE 256 /* MB */ -#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f -#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ - | CSCONFIG_ROW_BIT_13 \ - | CSCONFIG_COL_BIT_10 \ - | CSCONFIG_ODT_WR_ONLY_CURRENT) -#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 \ - | SDRAM_CFG_ECC_EN) -#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00001000 -#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) -#define CONFIG_SYS_DDR_INTERVAL ((256 << SDRAM_INTERVAL_BSTOPRE_SHIFT) \ - | (1115 << SDRAM_INTERVAL_REFINT_SHIFT)) -#define CONFIG_SYS_DDR_MODE 0x47800432 -#define CONFIG_SYS_DDR_MODE2 0x8000c000 - -#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ - (9 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ - (3 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \ - (3 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \ - (0 << TIMING_CFG0_WWT_SHIFT) | \ - (0 << TIMING_CFG0_RRT_SHIFT) | \ - (0 << TIMING_CFG0_WRT_SHIFT) | \ - (0 << TIMING_CFG0_RWT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_30) | \ - (2 << TIMING_CFG1_WRTORD_SHIFT) | \ - (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \ - (3 << TIMING_CFG1_WRREC_SHIFT) | \ - (10 << TIMING_CFG1_REFREC_SHIFT) | \ - (3 << TIMING_CFG1_ACTTORW_SHIFT) | \ - (8 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ - (3 << TIMING_CFG1_PRETOACT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_2 ((9 << TIMING_CFG2_FOUR_ACT_SHIFT) | \ - (4 << TIMING_CFG2_CKE_PLS_SHIFT) | \ - (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ - (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ - (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ - (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \ - (0 << TIMING_CFG2_CPO_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_3 0x00000000 - -/* - * Memory test - */ -#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ -#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */ -#define CONFIG_SYS_MEMTEST_END 0x00100000 - -/* - * The reserved memory - */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ -#define CONFIG_SYS_FLASH_BASE 0xFF800000 /* FLASH base address */ - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#else -#undef CONFIG_SYS_RAMBOOT -#endif - -#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */ - -/* - * Initial RAM Base Address Setup - */ -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - -/* - * Local Bus Configuration & Clock Setup - */ -#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP -#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4 -#define CONFIG_SYS_LBC_LBCR 0x00000000 - -/* - * FLASH on the Local Bus - */ -#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ -#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ -#define CONFIG_SYS_FLASH_SIZE 8 /* max FLASH size is 32M */ -#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use intel Flash protection. */ - - /* Window base at flash base */ -#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_32MB) - -#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \ - | BR_PS_16 /* 16 bit port */ \ - | BR_MS_GPCM /* MSEL = GPCM */ \ - | BR_V) /* valid */ -#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ - | OR_UPM_XAM \ - | OR_GPCM_CSNT \ - | OR_GPCM_ACS_DIV2 \ - | OR_GPCM_XACS \ - | OR_GPCM_SCY_15 \ - | OR_GPCM_TRLX_SET \ - | OR_GPCM_EHTR_SET \ - | OR_GPCM_EAD) - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */ - -#undef CONFIG_SYS_FLASH_CHECKSUM - -/* - * NAND flash on the local bus - */ -#define CONFIG_SYS_NAND_BASE 0x60000000 -#define CONFIG_CMD_NAND 1 -#define CONFIG_NAND_FSL_UPM 1 -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_MTD_NAND_VERIFY_WRITE - -#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE -/* - * [RFC] Comment said 4KB window; code said 256MB window; OR1 says 64MB - * ... What's correct? - */ -#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_256MB) - -/* Port size 8 bit, UPMA */ -#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_NAND_BASE \ - | BR_PS_8 \ - | BR_MS_UPMA \ - | BR_V) - /* 0x60000881 */ -#define CONFIG_SYS_OR1_PRELIM (OR_AM_64MB | OR_UPM_EAD) - /* 0xFC000001 */ - -/* - * Fujitsu MB86277 (MINT) graphics controller - */ -#define CONFIG_SYS_VIDEO_BASE 0x70000000 - -#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_VIDEO_BASE -#define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_64MB) - -/* Port size 32 bit, UPMB */ -#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_VIDEO_BASE \ - | BR_PS_32 \ - | BR_MS_UPMB \ - | BR_V) - /* 0x000018a1 */ -#define CONFIG_SYS_OR2_PRELIM (OR_AM_64MB | OR_UPM_EAD) - /* 0xFC000001 */ - -/* - * Serial Port - */ -#define CONFIG_CONS_INDEX 1 -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ -/* Use the HUSH parser */ -#define CONFIG_SYS_HUSH_PARSER - -/* Pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 -#define CONFIG_OF_STDOUT_VIA_ALIAS - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C2_SPEED 400000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x52} } - -/* - * General PCI - * Addresses are mapped 1-1. - */ -#define CONFIG_PCI - -#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 -#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE -#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 -#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE -#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI1_IO_BASE 0xE0300000 -#define CONFIG_SYS_PCI1_IO_PHYS 0xE0300000 -#define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */ - -#ifdef CONFIG_PCI -#define CONFIG_PCI_INDIRECT_BRIDGE - -#define CONFIG_PCI_PNP /* do pci plug-and-play */ - -#undef CONFIG_EEPRO100 -#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ - -#endif /* CONFIG_PCI */ - -/* - * QE UEC ethernet configuration - */ -#define CONFIG_UEC_ETH -#define CONFIG_ETHPRIME "UEC0" - -#define CONFIG_UEC_ETH1 /* GETH1 */ - -#ifdef CONFIG_UEC_ETH1 -#define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */ -#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE -#define CONFIG_SYS_UEC1_TX_CLK QE_CLK9 -#define CONFIG_SYS_UEC1_ETH_TYPE GIGA_ETH -#define CONFIG_SYS_UEC1_PHY_ADDR 2 -#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_RXID -#define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000 -#endif - -#define CONFIG_UEC_ETH2 /* GETH2 */ - -#ifdef CONFIG_UEC_ETH2 -#define CONFIG_SYS_UEC2_UCC_NUM 1 /* UCC2 */ -#define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE -#define CONFIG_SYS_UEC2_TX_CLK QE_CLK4 -#define CONFIG_SYS_UEC2_ETH_TYPE GIGA_ETH -#define CONFIG_SYS_UEC2_PHY_ADDR 4 -#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_RXID -#define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000 -#endif - -/* - * Environment - */ - -#ifndef CONFIG_SYS_RAMBOOT -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ -#define CONFIG_ENV_SIZE 0x20000 -#else /* CONFIG_SYS_RAMBOOT */ -#define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ -#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) -#define CONFIG_ENV_SIZE 0x2000 -#endif /* CONFIG_SYS_RAMBOOT */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_PING -#define CONFIG_CMD_I2C -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP - -#if defined(CONFIG_PCI) -#define CONFIG_CMD_PCI -#endif - -#if defined(CONFIG_SYS_RAMBOOT) -#undef CONFIG_CMD_SAVEENV -#undef CONFIG_CMD_LOADS -#endif - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ - -#if defined(CONFIG_CMD_KGDB) - #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else - #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif - - /* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ - /* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -/* - * For booting Linux, the board info and command line data - * have to be in the first 256 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ - -/* - * Core HID Setup - */ -#define CONFIG_SYS_HID0_INIT 0x000000000 -#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ - HID0_ENABLE_INSTRUCTION_CACHE) -#define CONFIG_SYS_HID2 HID2_HBE - -/* - * MMU Setup - */ - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ - -/* DDR: cache cacheable */ -#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \ - | BATL_PP_RW \ - | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \ - | BATU_BL_256M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L -#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U - -/* IMMRBAR & PCI IO: cache-inhibit and guarded */ -#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR \ - | BATL_PP_RW \ - | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR \ - | BATU_BL_4M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L -#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U - -/* NAND: cache-inhibit and guarded */ -#define CONFIG_SYS_IBAT2L (CONFIG_SYS_NAND_BASE \ - | BATL_PP_RW \ - | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_IBAT2U (CONFIG_SYS_NAND_BASE \ - | BATU_BL_64M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L -#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U - -/* FLASH: icache cacheable, but dcache-inhibit and guarded */ -#define CONFIG_SYS_IBAT3L (CONFIG_SYS_FLASH_BASE \ - | BATL_PP_RW \ - | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT3U (CONFIG_SYS_FLASH_BASE \ - | BATU_BL_32M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT3L (CONFIG_SYS_FLASH_BASE \ - | BATL_PP_RW \ - | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U - -/* Stack in dcache: cacheable, no memory coherence */ -#define CONFIG_SYS_IBAT4L (CONFIG_SYS_INIT_RAM_ADDR \ - | BATL_PP_RW) -#define CONFIG_SYS_IBAT4U (CONFIG_SYS_INIT_RAM_ADDR \ - | BATU_BL_128K \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L -#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U - -#define CONFIG_SYS_IBAT5L (CONFIG_SYS_VIDEO_BASE \ - | BATL_PP_RW \ - | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_IBAT5U (CONFIG_SYS_VIDEO_BASE \ - | BATU_BL_64M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L -#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U - -#ifdef CONFIG_PCI -/* PCI MEM space: cacheable */ -#define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI1_MEM_PHYS \ - | BATL_PP_RW \ - | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI1_MEM_PHYS \ - | BATU_BL_256M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L -#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U -/* PCI MMIO space: cache-inhibit and guarded */ -#define CONFIG_SYS_IBAT7L (CONFIG_SYS_PCI1_MMIO_PHYS \ - | BATL_PP_RW \ - | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_IBAT7U (CONFIG_SYS_PCI1_MMIO_PHYS \ - | BATU_BL_256M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L -#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U -#else /* CONFIG_PCI */ -#define CONFIG_SYS_IBAT6L (0) -#define CONFIG_SYS_IBAT6U (0) -#define CONFIG_SYS_IBAT7L (0) -#define CONFIG_SYS_IBAT7U (0) -#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L -#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U -#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L -#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U -#endif /* CONFIG_PCI */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ -#endif - -/* - * Environment Configuration - */ -#define CONFIG_ENV_OVERWRITE - -#if defined(CONFIG_UEC_ETH) -#define CONFIG_HAS_ETH0 -#define CONFIG_HAS_ETH1 -#define CONFIG_HAS_ETH2 -#define CONFIG_HAS_ETH3 -#endif - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_LOADADDR a00000 -#define CONFIG_HOSTNAME mpc8360erdk -#define CONFIG_BOOTFILE "uImage" - -#define CONFIG_ROOTPATH "/nfsroot/" - -#define CONFIG_BOOTDELAY 2 /* -1 disables auto-boot */ -#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "consoledev=ttyS0\0" \ - "loadaddr=a00000\0" \ - "fdtaddr=900000\0" \ - "fdtfile=mpc836x_rdk.dtb\0" \ - "fsfile=fs\0" \ - "ubootfile=u-boot.bin\0" \ - "mtdparts=mtdparts=60000000.nand-flash:4096k(kernel),128k(dtb),"\ - "-(rootfs)\0" \ - "setbootargs=setenv bootargs console=$consoledev,$baudrate " \ - "$mtdparts panic=1\0" \ - "adddhcpargs=setenv bootargs $bootargs ip=on\0" \ - "addnfsargs=setenv bootargs $bootargs ip=$ipaddr:$serverip:" \ - "$gatewayip:$netmask:$hostname:$netdev:off " \ - "root=/dev/nfs rw nfsroot=$serverip:$rootpath\0" \ - "addnandargs=setenv bootargs $bootargs root=/dev/mtdblock3 " \ - "rootfstype=jffs2 rw\0" \ - "tftp_get_uboot=tftp 100000 $ubootfile\0" \ - "tftp_get_kernel=tftp $loadaddr $bootfile\0" \ - "tftp_get_dtb=tftp $fdtaddr $fdtfile\0" \ - "tftp_get_fs=tftp c00000 $fsfile\0" \ - "nand_erase_kernel=nand erase 0 400000\0" \ - "nand_erase_dtb=nand erase 400000 20000\0" \ - "nand_erase_fs=nand erase 420000 3be0000\0" \ - "nand_write_kernel=nand write.jffs2 $loadaddr 0 400000\0" \ - "nand_write_dtb=nand write.jffs2 $fdtaddr 400000 20000\0" \ - "nand_write_fs=nand write.jffs2 c00000 420000 $filesize\0" \ - "nand_read_kernel=nand read.jffs2 $loadaddr 0 400000\0" \ - "nand_read_dtb=nand read.jffs2 $fdtaddr 400000 20000\0" \ - "nor_reflash=protect off ff800000 ff87ffff ; " \ - "erase ff800000 ff87ffff ; " \ - "cp.b 100000 ff800000 $filesize\0" \ - "nand_reflash_kernel=run tftp_get_kernel nand_erase_kernel " \ - "nand_write_kernel\0" \ - "nand_reflash_dtb=run tftp_get_dtb nand_erase_dtb nand_write_dtb\0"\ - "nand_reflash_fs=run tftp_get_fs nand_erase_fs nand_write_fs\0" \ - "nand_reflash=run nand_reflash_kernel nand_reflash_dtb " \ - "nand_reflash_fs\0" \ - "boot_m=bootm $loadaddr - $fdtaddr\0" \ - "dhcpboot=dhcp ; run setbootargs adddhcpargs tftp_get_dtb boot_m\0"\ - "nfsboot=run setbootargs addnfsargs tftp_get_kernel tftp_get_dtb "\ - "boot_m\0" \ - "nandboot=run setbootargs addnandargs nand_read_kernel nand_read_dtb "\ - "boot_m\0" \ - "" - -#define CONFIG_BOOTCOMMAND "run dhcpboot" - -#endif /* __CONFIG_H */ |