diff options
Diffstat (limited to 'include/configs/MOUSSE.h')
| -rw-r--r-- | include/configs/MOUSSE.h | 332 |
1 files changed, 332 insertions, 0 deletions
diff --git a/include/configs/MOUSSE.h b/include/configs/MOUSSE.h new file mode 100644 index 0000000..109ed3d --- /dev/null +++ b/include/configs/MOUSSE.h @@ -0,0 +1,332 @@ +/* + * (C) Copyright 2000, 2001 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * (C) Copyright 2001 + * James F. Dougherty (jfd@cs.stanford.edu) + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * + * Configuration settings for the MOUSSE board. + * See also: http://www.vooha.com/ + * + */ + +/* ------------------------------------------------------------------------- */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC824X 1 +#define CONFIG_MPC8240 1 +#define CONFIG_MOUSSE 1 +#define CFG_ADDR_MAP_B 1 +#define CONFIG_CONS_INDEX 1 +#define CONFIG_BAUDRATE 9600 +#if 1 +#define CONFIG_BOOTCOMMAND "tftp 100000 vmlinux.img;bootm" /* autoboot command */ +#else +#define CONFIG_BOOTCOMMAND "bootm ffe10000" +#endif +#define CONFIG_BOOTARGS "console=ttyS0 root=/dev/nfs rw nfsroot=209.128.93.133:/boot nfsaddrs=209.128.93.133:209.128.93.138" +#define CONFIG_BOOTDELAY 3 +#define CONFIG_COMMANDS (CONFIG_CMD_DFL|CFG_CMD_ASKENV|CFG_CMD_DATE) +#define CONFIG_ENV_OVERWRITE 1 +#define CONFIG_ETH_ADDR "00:10:18:10:00:06" + +#define CONFIG_DOS_PARTITION 1 /* MSDOS bootable partitiion support */ +/* This must be included AFTER the definition of CONFIG_COMMANDS (if any) + */ +#include <cmd_confdefs.h> +#include "../board/mousse/mousse.h" + +/* + * Miscellaneous configurable options + */ +#undef CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=>" /* Monitor Command Prompt */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) +#define CFG_MAXARGS 8 /* Max number of command args */ + +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_LOAD_ADDR 0x00100000 /* Default load address */ + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 + +#ifdef DEBUG +#define CFG_MONITOR_BASE CFG_SDRAM_BASE +#else +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#endif + +#ifdef DEBUG +#define CFG_MONITOR_LEN (4 << 20) /* lots of mem ... */ +#else +#define CFG_MONITOR_LEN (512 << 10) /* 512K PLCC bootrom */ +#endif +#define CFG_MALLOC_LEN (2*(4096 << 10)) /* 2*4096kB for malloc() */ + +#define CFG_MEMTEST_START 0x00004000 /* memtest works on */ +#define CFG_MEMTEST_END 0x02000000 /* 0 ... 32 MB in DRAM */ + + +#define CFG_EUMB_ADDR 0xFC000000 + +#define CFG_ISA_MEM 0xFD000000 +#define CFG_ISA_IO 0xFE000000 + +#define CFG_FLASH_BASE 0xFFF00000 +#define CFG_FLASH_SIZE ((uint)(512 * 1024)) +#define CFG_RESET_ADDRESS 0xFFF00100 +#define FLASH_BASE0_PRELIM 0xFFF00000 /* 512K PLCC FLASH/AM29F040*/ +#define FLASH_BASE0_SIZE 0x80000 /* 512K */ +#define FLASH_BASE1_PRELIM 0xFFE10000 /* AMD 29LV160DB + 1MB - 64K FLASH0 SEG =960K + (size=0xf0000)*/ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * NS16550 Configuration + */ +#define CFG_NS16550 +#define CFG_NS16550_SERIAL + +#define CFG_NS16550_REG_SIZE 1 + +#define CFG_NS16550_CLK 18432000 + +#define CFG_NS16550_COM1 0xFFE08080 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_SDRAM_BASE + CFG_MONITOR_LEN +#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + * For the detail description refer to the MPC8240 user's manual. + */ + +#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */ +#define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER 2 +#define CFG_HZ 1000 + +#define CFG_ETH_DEV_FN 0x00 +#define CFG_ETH_IOBASE 0x00104000 + + + /* Bit-field values for MCCR1. + */ +#define CFG_ROMNAL 8 +#define CFG_ROMFAL 8 + + /* Bit-field values for MCCR2. + */ +#define CFG_REFINT 0xf5 /* Refresh interval */ + + /* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4. + */ +#define CFG_BSTOPRE 0x79 + +#ifdef INCLUDE_ECC +#define USE_ECC 1 +#else /* INCLUDE_ECC */ +#define USE_ECC 0 +#endif /* INCLUDE_ECC */ + + + /* Bit-field values for MCCR3. + */ +#define CFG_REFREC 8 /* Refresh to activate interval */ +#define CFG_RDLAT (4+USE_ECC) /* Data latancy from read command */ + + /* Bit-field values for MCCR4. + */ +#define CFG_PRETOACT 3 /* Precharge to activate interval */ +#define CFG_ACTTOPRE 5 /* Activate to Precharge interval */ +#define CFG_SDMODE_CAS_LAT 3 /* SDMODE CAS latancy */ +#define CFG_SDMODE_WRAP 0 /* SDMODE wrap type */ +#define CFG_SDMODE_BURSTLEN 2 /* SDMODE Burst length */ +#define CFG_ACTORW 2 +#define CFG_REGISTERD_TYPE_BUFFER (1-USE_ECC) + +/* Memory bank settings. + * Only bits 20-29 are actually used from these vales to set the + * start/end addresses. The upper two bits will always be 0, and the lower + * 20 bits will be 0x00000 for a start address, or 0xfffff for an end + * address. Refer to the MPC8240 book. + */ +#define CFG_RAM_SIZE 0x04000000 /* 64MB */ + + +#define CFG_BANK0_START 0x00000000 +#define CFG_BANK0_END (CFG_RAM_SIZE - 1) +#define CFG_BANK0_ENABLE 1 +#define CFG_BANK1_START 0x3ff00000 +#define CFG_BANK1_END 0x3fffffff +#define CFG_BANK1_ENABLE 0 +#define CFG_BANK2_START 0x3ff00000 +#define CFG_BANK2_END 0x3fffffff +#define CFG_BANK2_ENABLE 0 +#define CFG_BANK3_START 0x3ff00000 +#define CFG_BANK3_END 0x3fffffff +#define CFG_BANK3_ENABLE 0 +#define CFG_BANK4_START 0x3ff00000 +#define CFG_BANK4_END 0x3fffffff +#define CFG_BANK4_ENABLE 0 +#define CFG_BANK5_START 0x3ff00000 +#define CFG_BANK5_END 0x3fffffff +#define CFG_BANK5_ENABLE 0 +#define CFG_BANK6_START 0x3ff00000 +#define CFG_BANK6_END 0x3fffffff +#define CFG_BANK6_ENABLE 0 +#define CFG_BANK7_START 0x3ff00000 +#define CFG_BANK7_END 0x3fffffff +#define CFG_BANK7_ENABLE 0 + +#define CFG_ODCR 0x7f + + +#define CFG_PGMAX 0x32 /* how long the 8240 reatins the currently accessed page in memory + see 8240 book for details*/ +#define PCI_MEM_SPACE1_START 0x80000000 +#define PCI_MEM_SPACE2_START 0xfd000000 + +/* IBAT/DBAT Configuration */ +/* Ram: 64MB, starts at address-0, r/w instruction/data */ +#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_64M | BATU_VS | BATU_VP) +#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_DBAT0U CFG_IBAT0U +#define CFG_DBAT0L CFG_IBAT0L + +/* MPLD/Port-X I/O Space : data and instruction read/write, cache-inhibit */ +#define CFG_IBAT1U (PORTX_DEV_BASE | BATU_BL_128M | BATU_VS | BATU_VP) +#if 0 +#define CFG_IBAT1L (PORTX_DEV_BASE | BATL_PP_10 | BATL_MEMCOHERENCE |\ + BATL_WRITETHROUGH | BATL_CACHEINHIBIT) +#else +#define CFG_IBAT1L (PORTX_DEV_BASE | BATL_PP_10 |BATL_CACHEINHIBIT) +#endif +#define CFG_DBAT1U CFG_IBAT1U +#define CFG_DBAT1L CFG_IBAT1L + +/* PCI Memory region 1: 0x8XXX_XXXX PCI Mem space: EUMBAR, etc - 16MB */ +#define CFG_IBAT2U (PCI_MEM_SPACE1_START|BATU_BL_16M | BATU_VS | BATU_VP) +#define CFG_IBAT2L (PCI_MEM_SPACE1_START|BATL_PP_10 | BATL_GUARDEDSTORAGE|BATL_CACHEINHIBIT) +#define CFG_DBAT2U CFG_IBAT2U +#define CFG_DBAT2L CFG_IBAT2L + +/* PCI Memory region 2: PCI Devices in 0xFD space */ +#define CFG_IBAT3U (PCI_MEM_SPACE2_START|BATU_BL_16M | BATU_VS | BATU_VP) +#define CFG_IBAT3L (PCI_MEM_SPACE2_START|BATL_PP_10 | BATL_GUARDEDSTORAGE | BATL_CACHEINHIBIT) +#define CFG_DBAT3U CFG_IBAT3U +#define CFG_DBAT3L CFG_IBAT3L + + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 3 /* Max number of flash banks */ +#define CFG_MAX_FLASH_SECT 64 /* Max number of sectors in one bank */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#if 0 +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_OFFSET 0x8000 /* Offset of the Environment Sector */ +#define CFG_ENV_SIZE 0x4000 /* Size of the Environment Sector */ +#else +#define CFG_ENV_IS_IN_NVRAM 1 +#define CFG_ENV_ADDR NV_OFF_U_BOOT_ADDR /* PortX NVM Free addr*/ +#define CFG_ENV_OFFSET CFG_ENV_ADDR +#define CFG_ENV_SIZE NV_U_BOOT_ENV_SIZE /* 2K */ +#endif +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 + + + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +/* Localizations */ +#if 0 +#define CONFIG_ETHADDR 0:0:0:0:1:d +#define CONFIG_IPADDR 172.16.40.113 +#define CONFIG_SERVERIP 172.16.40.111 +#else +#define CONFIG_ETHADDR 0:0:0:0:1:d +#define CONFIG_IPADDR 209.128.93.138 +#define CONFIG_SERVERIP 209.128.93.133 +#endif + +/*----------------------------------------------------------------------- + * PCI stuff + *----------------------------------------------------------------------- + */ +#define CONFIG_PCI /* include pci support */ +#undef CONFIG_PCI_PNP + +#define CONFIG_NET_MULTI /* Multi ethernet cards support */ + +#define CONFIG_TULIP + +#endif /* __CONFIG_H */ + + |