diff options
Diffstat (limited to 'include/configs/M5329EVB.h')
| -rw-r--r-- | include/configs/M5329EVB.h | 156 |
1 files changed, 78 insertions, 78 deletions
diff --git a/include/configs/M5329EVB.h b/include/configs/M5329EVB.h index 58948a2..c207947 100644 --- a/include/configs/M5329EVB.h +++ b/include/configs/M5329EVB.h @@ -38,9 +38,9 @@ #define CONFIG_M5329 /* define processor type */ #define CONFIG_MCFUART -#define CFG_UART_PORT (0) +#define CONFIG_SYS_UART_PORT (0) #define CONFIG_BAUDRATE 115200 -#define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } +#define CONFIG_SYS_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } #undef CONFIG_WATCHDOG #define CONFIG_WATCHDOG_TIMEOUT 5000 /* timeout in milliseconds, max timeout is 6.71sec */ @@ -64,29 +64,29 @@ # define CONFIG_CMD_NAND #endif -#define CFG_UNIFY_CACHE +#define CONFIG_SYS_UNIFY_CACHE #define CONFIG_MCFFEC #ifdef CONFIG_MCFFEC # define CONFIG_NET_MULTI 1 # define CONFIG_MII 1 # define CONFIG_MII_INIT 1 -# define CFG_DISCOVER_PHY -# define CFG_RX_ETH_BUFFER 8 -# define CFG_FAULT_ECHO_LINK_DOWN +# define CONFIG_SYS_DISCOVER_PHY +# define CONFIG_SYS_RX_ETH_BUFFER 8 +# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN -# define CFG_FEC0_PINMUX 0 -# define CFG_FEC0_MIIBASE CFG_FEC0_IOBASE +# define CONFIG_SYS_FEC0_PINMUX 0 +# define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE # define MCFFEC_TOUT_LOOP 50000 -/* If CFG_DISCOVER_PHY is not defined - hardcoded */ -# ifndef CFG_DISCOVER_PHY +/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ +# ifndef CONFIG_SYS_DISCOVER_PHY # define FECDUPLEX FULL # define FECSPEED _100BASET # else -# ifndef CFG_FAULT_ECHO_LINK_DOWN -# define CFG_FAULT_ECHO_LINK_DOWN +# ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN +# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN # endif -# endif /* CFG_DISCOVER_PHY */ +# endif /* CONFIG_SYS_DISCOVER_PHY */ #endif #define CONFIG_MCFRTC @@ -100,10 +100,10 @@ #define CONFIG_FSL_I2C #define CONFIG_HARD_I2C /* I2C with hw support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 80000 -#define CFG_I2C_SLAVE 0x7F -#define CFG_I2C_OFFSET 0x58000 -#define CFG_IMMR CFG_MBAR +#define CONFIG_SYS_I2C_SPEED 80000 +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_OFFSET 0x58000 +#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR #define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */ #define CONFIG_UDP_CHECKSUM @@ -131,27 +131,27 @@ "" #define CONFIG_PRAM 512 /* 512 KB */ -#define CFG_PROMPT "-> " -#define CFG_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "-> " +#define CONFIG_SYS_LONGHELP /* undef to save memory */ #ifdef CONFIG_CMD_KGDB -# define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -# define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_LOAD_ADDR 0x40010000 +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_LOAD_ADDR 0x40010000 -#define CFG_HZ 1000 -#define CFG_CLK 80000000 -#define CFG_CPU_CLK CFG_CLK * 3 +#define CONFIG_SYS_HZ 1000 +#define CONFIG_SYS_CLK 80000000 +#define CONFIG_SYS_CPU_CLK CONFIG_SYS_CLK * 3 -#define CFG_MBAR 0xFC000000 +#define CONFIG_SYS_MBAR 0xFC000000 -#define CFG_LATCH_ADDR (CFG_CS1_BASE + 0x80000) +#define CONFIG_SYS_LATCH_ADDR (CONFIG_SYS_CS1_BASE + 0x80000) /* * Low Level Configuration Settings @@ -161,82 +161,82 @@ /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in DPRAM) */ -#define CFG_INIT_RAM_ADDR 0x80000000 -#define CFG_INIT_RAM_END 0x8000 /* End of used area in internal SRAM */ -#define CFG_INIT_RAM_CTRL 0x221 -#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ -#define CFG_GBL_DATA_OFFSET ((CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) - 0x10) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_RAM_ADDR 0x80000000 +#define CONFIG_SYS_INIT_RAM_END 0x8000 /* End of used area in internal SRAM */ +#define CONFIG_SYS_INIT_RAM_CTRL 0x221 +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) - 0x10) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ -#define CFG_SDRAM_BASE 0x40000000 -#define CFG_SDRAM_SIZE 32 /* SDRAM size in MB */ -#define CFG_SDRAM_CFG1 0x53722730 -#define CFG_SDRAM_CFG2 0x56670000 -#define CFG_SDRAM_CTRL 0xE1092000 -#define CFG_SDRAM_EMOD 0x40010000 -#define CFG_SDRAM_MODE 0x018D0000 +#define CONFIG_SYS_SDRAM_BASE 0x40000000 +#define CONFIG_SYS_SDRAM_SIZE 32 /* SDRAM size in MB */ +#define CONFIG_SYS_SDRAM_CFG1 0x53722730 +#define CONFIG_SYS_SDRAM_CFG2 0x56670000 +#define CONFIG_SYS_SDRAM_CTRL 0xE1092000 +#define CONFIG_SYS_SDRAM_EMOD 0x40010000 +#define CONFIG_SYS_SDRAM_MODE 0x018D0000 -#define CFG_MEMTEST_START CFG_SDRAM_BASE + 0x400 -#define CFG_MEMTEST_END ((CFG_SDRAM_SIZE - 3) << 20) +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE + 0x400 +#define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20) -#define CFG_MONITOR_BASE (CFG_FLASH_BASE + 0x400) -#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) +#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CFG_BOOTPARAMS_LEN 64*1024 -#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ +#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 +#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization ?? */ -#define CFG_BOOTMAPSZ (CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20)) +#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20)) /*----------------------------------------------------------------------- * FLASH organization */ -#define CFG_FLASH_CFI -#ifdef CFG_FLASH_CFI +#define CONFIG_SYS_FLASH_CFI +#ifdef CONFIG_SYS_FLASH_CFI # define CONFIG_FLASH_CFI_DRIVER 1 -# define CFG_FLASH_SIZE 0x800000 /* Max size that the board might have */ -# define CFG_FLASH_CFI_WIDTH FLASH_CFI_16BIT -# define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ -# define CFG_MAX_FLASH_SECT 137 /* max number of sectors on one chip */ -# define CFG_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ +# define CONFIG_SYS_FLASH_SIZE 0x800000 /* Max size that the board might have */ +# define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT +# define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +# define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */ +# define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ #endif #ifdef NANDFLASH_SIZE -# define CFG_MAX_NAND_DEVICE 1 -# define CFG_NAND_BASE CFG_CS2_BASE -# define CFG_NAND_SIZE 1 -# define CFG_NAND_BASE_LIST { CFG_NAND_BASE } +# define CONFIG_SYS_MAX_NAND_DEVICE 1 +# define CONFIG_SYS_NAND_BASE CONFIG_SYS_CS2_BASE +# define CONFIG_SYS_NAND_SIZE 1 +# define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } # define NAND_MAX_CHIPS 1 # define NAND_ALLOW_ERASE_ALL 1 # define CONFIG_JFFS2_NAND 1 # define CONFIG_JFFS2_DEV "nand0" -# define CONFIG_JFFS2_PART_SIZE (CFG_CS2_MASK & ~1) +# define CONFIG_JFFS2_PART_SIZE (CONFIG_SYS_CS2_MASK & ~1) # define CONFIG_JFFS2_PART_OFFSET 0x00000000 #endif -#define CFG_FLASH_BASE CFG_CS0_BASE +#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE /* Configuration for environment * Environment is embedded in u-boot in the second sector of the flash */ -#define CFG_ENV_OFFSET 0x4000 -#define CFG_ENV_SECT_SIZE 0x2000 -#define CFG_ENV_IS_IN_FLASH 1 -#define CFG_ENV_IS_EMBEDDED 1 +#define CONFIG_ENV_OFFSET 0x4000 +#define CONFIG_ENV_SECT_SIZE 0x2000 +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_IS_EMBEDDED 1 /*----------------------------------------------------------------------- * Cache Configuration */ -#define CFG_CACHELINE_SIZE 16 +#define CONFIG_SYS_CACHELINE_SIZE 16 /*----------------------------------------------------------------------- * Chipselect bank definitions @@ -249,18 +249,18 @@ * CS4 - Available * CS5 - Available */ -#define CFG_CS0_BASE 0 -#define CFG_CS0_MASK 0x007f0001 -#define CFG_CS0_CTRL 0x00001fa0 +#define CONFIG_SYS_CS0_BASE 0 +#define CONFIG_SYS_CS0_MASK 0x007f0001 +#define CONFIG_SYS_CS0_CTRL 0x00001fa0 -#define CFG_CS1_BASE 0x10000000 -#define CFG_CS1_MASK 0x001f0001 -#define CFG_CS1_CTRL 0x002A3780 +#define CONFIG_SYS_CS1_BASE 0x10000000 +#define CONFIG_SYS_CS1_MASK 0x001f0001 +#define CONFIG_SYS_CS1_CTRL 0x002A3780 #ifdef NANDFLASH_SIZE -#define CFG_CS2_BASE 0x20000000 -#define CFG_CS2_MASK ((NANDFLASH_SIZE << 20) | 1) -#define CFG_CS2_CTRL 0x00001f60 +#define CONFIG_SYS_CS2_BASE 0x20000000 +#define CONFIG_SYS_CS2_MASK ((NANDFLASH_SIZE << 20) | 1) +#define CONFIG_SYS_CS2_CTRL 0x00001f60 #endif #endif /* _M5329EVB_H */ |