diff options
Diffstat (limited to 'include/configs/M5282EVB.h')
| -rw-r--r-- | include/configs/M5282EVB.h | 147 |
1 files changed, 116 insertions, 31 deletions
diff --git a/include/configs/M5282EVB.h b/include/configs/M5282EVB.h index f2a7644..3c17c1e 100644 --- a/include/configs/M5282EVB.h +++ b/include/configs/M5282EVB.h @@ -33,15 +33,17 @@ * High Level Configuration Options * (easy to change) */ -#define CONFIG_MCF52x2 /* define processor family */ -#define CONFIG_M5282 /* define processor type */ +#define CONFIG_MCF52x2 /* define processor family */ +#define CONFIG_M5282 /* define processor type */ -#define FEC_ENET +#define CONFIG_MCFTMR +#define CONFIG_MCFUART +#define CFG_UART_PORT (0) #define CONFIG_BAUDRATE 19200 #define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } -#define CONFIG_MONITOR_IS_IN_RAM /* define if monitor is started from a pre-loader */ +#undef CONFIG_MONITOR_IS_IN_RAM /* define if monitor is started from a pre-loader */ /* Configuration for environment * Environment is embedded in u-boot in the second sector of the flash @@ -50,7 +52,6 @@ #define CFG_ENV_SIZE 0x2000 #define CFG_ENV_IS_IN_FLASH 1 - /* * BOOTP options */ @@ -59,29 +60,73 @@ #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME - /* * Command line configuration. */ #include <config_cmd_default.h> +#define CONFIG_CMD_NET +#define CONFIG_CMD_PING +#define CONFIG_CMD_MII #undef CONFIG_CMD_LOADS #undef CONFIG_CMD_LOADB +#define CONFIG_MCFFEC +#ifdef CONFIG_MCFFEC +# define CONFIG_NET_MULTI 1 +# define CONFIG_MII 1 +# define CFG_DISCOVER_PHY +# define CFG_RX_ETH_BUFFER 8 +# define CFG_FAULT_ECHO_LINK_DOWN + +# define CFG_FEC0_PINMUX 0 +# define CFG_FEC0_MIIBASE CFG_FEC0_IOBASE +# define MCFFEC_TOUT_LOOP 50000 +/* If CFG_DISCOVER_PHY is not defined - hardcoded */ +# ifndef CFG_DISCOVER_PHY +# define FECDUPLEX FULL +# define FECSPEED _100BASET +# else +# ifndef CFG_FAULT_ECHO_LINK_DOWN +# define CFG_FAULT_ECHO_LINK_DOWN +# endif +# endif /* CFG_DISCOVER_PHY */ +#endif #define CONFIG_BOOTDELAY 5 +#ifdef CONFIG_MCFFEC +# define CONFIG_ETHADDR 00:e0:0c:bc:e5:60 +# define CONFIG_IPADDR 192.162.1.2 +# define CONFIG_NETMASK 255.255.255.0 +# define CONFIG_SERVERIP 192.162.1.1 +# define CONFIG_GATEWAYIP 192.162.1.1 +# define CONFIG_OVERWRITE_ETHADDR_ONCE +#endif /* CONFIG_MCFFEC */ + +#define CONFIG_HOSTNAME M5272C3 +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "loadaddr=10000\0" \ + "u-boot=u-boot.bin\0" \ + "load=tftp ${loadaddr) ${u-boot}\0" \ + "upd=run load; run prog\0" \ + "prog=prot off ffe00000 ffe3ffff;" \ + "era ffe00000 ffe3ffff;" \ + "cp.b ${loadaddr} ffe00000 ${filesize};"\ + "save\0" \ + "" #define CFG_PROMPT "-> " -#define CFG_LONGHELP /* undef to save memory */ +#define CFG_LONGHELP /* undef to save memory */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ #define CFG_LOAD_ADDR 0x20000 @@ -91,6 +136,10 @@ #define CFG_HZ 1000000 #define CFG_CLK 64000000 +/* PLL Configuration: Ext Clock * 6 (see table 9-4 of MCF user manual) */ + +#define CFG_MFD 0x02 /* PLL Multiplication Factor Devider */ +#define CFG_RFD 0x00 /* PLL Reduce Frecuency Devider */ /* * Low Level Configuration Settings @@ -99,15 +148,12 @@ */ #define CFG_MBAR 0x40000000 -#undef CFG_DISCOVER_PHY -#define CFG_ENET_BD_BASE 0x380000 - /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in DPRAM) */ -#define CFG_INIT_RAM_ADDR 0x20000000 -#define CFG_INIT_RAM_END 0x10000 /* End of used area in internal SRAM */ -#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_INIT_RAM_ADDR 0x20000000 +#define CFG_INIT_RAM_END 0x10000 /* End of used area in internal SRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET @@ -117,49 +163,88 @@ * Please note that CFG_SDRAM_BASE _must_ start at 0 */ #define CFG_SDRAM_BASE 0x00000000 -#define CFG_SDRAM_SIZE 4 /* SDRAM size in MB */ +#define CFG_SDRAM_SIZE 8 /* SDRAM size in MB */ #define CFG_FLASH_BASE 0xffe00000 #define CFG_INT_FLASH_BASE 0xf0000000 +#define CFG_INT_FLASH_ENABLE 0x21 /* If M5282 port is fully implemented the monitor base will be behind * the vector table. */ -/* #define CFG_MONITOR_BASE (CFG_FLASH_BASE + 0x400) */ -#define CFG_MONITOR_BASE 0x20000 +#if (TEXT_BASE != CFG_INT_FLASH_BASE) +#define CFG_MONITOR_BASE (CFG_FLASH_BASE + 0x400) +#else +#define CFG_MONITOR_BASE (TEXT_BASE + 0x418) /* 24 Byte for CFM-Config */ +#endif #define CFG_MONITOR_LEN 0x20000 #define CFG_MALLOC_LEN (256 << 10) #define CFG_BOOTPARAMS_LEN 64*1024 - /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization ?? */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - +#define CFG_BOOTMAPSZ (CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20)) /*----------------------------------------------------------------------- * FLASH organization */ -#define CFG_MAX_FLASH_SECT 35 -#define CFG_MAX_FLASH_BANKS 1 -#define CFG_FLASH_ERASE_TOUT 10000000 +#define CFG_FLASH_CFI +#ifdef CFG_FLASH_CFI + +# define CFG_FLASH_CFI_DRIVER 1 +# define CFG_FLASH_SIZE 0x1000000 /* Max size that the board might have */ +# define CFG_FLASH_CFI_WIDTH FLASH_CFI_16BIT +# define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +# define CFG_MAX_FLASH_SECT 137 /* max number of sectors on one chip */ +# define CFG_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ +# define CFG_FLASH_CHECKSUM +# define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } +#endif /*----------------------------------------------------------------------- * Cache Configuration */ #define CFG_CACHELINE_SIZE 16 - /*----------------------------------------------------------------------- * Memory bank definitions */ - - +#define CFG_CS0_BASE CFG_FLASH_BASE +#define CFG_CS0_SIZE 2*1024*1024 +#define CFG_CS0_WIDTH 16 +#define CFG_CS0_RO 0 +#define CFG_CS0_WS 6 +/* +#define CFG_CS3_BASE 0xE0000000 +#define CFG_CS3_SIZE 1*1024*1024 +#define CFG_CS3_WIDTH 16 +#define CFG_CS3_RO 0 +#define CFG_CS3_WS 6 +*/ /*----------------------------------------------------------------------- * Port configuration */ +#define CFG_PACNT 0x0000000 /* Port A D[31:24] */ +#define CFG_PADDR 0x0000000 +#define CFG_PADAT 0x0000000 + +#define CFG_PBCNT 0x0000000 /* Port B D[23:16] */ +#define CFG_PBDDR 0x0000000 +#define CFG_PBDAT 0x0000000 + +#define CFG_PCCNT 0x0000000 /* Port C D[15:08] */ +#define CFG_PCDDR 0x0000000 +#define CFG_PCDAT 0x0000000 + +#define CFG_PDCNT 0x0000000 /* Port D D[07:00] */ +#define CFG_PCDDR 0x0000000 +#define CFG_PCDAT 0x0000000 +#define CFG_PEHLPAR 0xC0 +#define CFG_PUAPAR 0x0F /* UA0..UA3 = Uart 0 +1 */ +#define CFG_DDRUA 0x05 +#define CFG_PJPAR 0xFF; -#endif /* _CONFIG_M5282EVB_H */ +#endif /* _CONFIG_M5282EVB_H */ |