diff options
Diffstat (limited to 'include/configs/M5275EVB.h')
| -rw-r--r-- | include/configs/M5275EVB.h | 122 |
1 files changed, 61 insertions, 61 deletions
diff --git a/include/configs/M5275EVB.h b/include/configs/M5275EVB.h index b0ef41e..1f3539e 100644 --- a/include/configs/M5275EVB.h +++ b/include/configs/M5275EVB.h @@ -44,9 +44,9 @@ #define CONFIG_MCFTMR #define CONFIG_MCFUART -#define CFG_UART_PORT (0) +#define CONFIG_SYS_UART_PORT (0) #define CONFIG_BAUDRATE 115200 -#define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } +#define CONFIG_SYS_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } /* Configuration for environment * Environment is embedded in u-boot in the second sector of the flash @@ -90,22 +90,22 @@ #define CONFIG_NET_MULTI 1 #define CONFIG_MII 1 #define CONFIG_MII_INIT 1 -#define CFG_DISCOVER_PHY -#define CFG_RX_ETH_BUFFER 8 -#define CFG_FAULT_ECHO_LINK_DOWN -#define CFG_FEC0_PINMUX 0 -#define CFG_FEC0_MIIBASE CFG_FEC0_IOBASE -#define CFG_FEC1_PINMUX 0 -#define CFG_FEC1_MIIBASE CFG_FEC1_IOBASE +#define CONFIG_SYS_DISCOVER_PHY +#define CONFIG_SYS_RX_ETH_BUFFER 8 +#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN +#define CONFIG_SYS_FEC0_PINMUX 0 +#define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE +#define CONFIG_SYS_FEC1_PINMUX 0 +#define CONFIG_SYS_FEC1_MIIBASE CONFIG_SYS_FEC1_IOBASE #define MCFFEC_TOUT_LOOP 50000 #define CONFIG_HAS_ETH1 -/* If CFG_DISCOVER_PHY is not defined - hardcoded */ -#ifndef CFG_DISCOVER_PHY +/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ +#ifndef CONFIG_SYS_DISCOVER_PHY #define FECDUPLEX FULL #define FECSPEED _100BASET #else -#ifndef CFG_FAULT_ECHO_LINK_DOWN -#define CFG_FAULT_ECHO_LINK_DOWN +#ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN +#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN #endif #endif #endif @@ -114,40 +114,40 @@ #define CONFIG_FSL_I2C #define CONFIG_HARD_I2C /* I2C with hw support */ #undef CONFIG_SOFT_I2C -#define CFG_I2C_SPEED 80000 -#define CFG_I2C_SLAVE 0x7F -#define CFG_I2C_OFFSET 0x00000300 -#define CFG_IMMR CFG_MBAR -#define CFG_I2C_PINMUX_REG (gpio_reg->par_feci2c) -#define CFG_I2C_PINMUX_CLR (0xFFF0) -#define CFG_I2C_PINMUX_SET (0x000F) +#define CONFIG_SYS_I2C_SPEED 80000 +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_OFFSET 0x00000300 +#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR +#define CONFIG_SYS_I2C_PINMUX_REG (gpio_reg->par_feci2c) +#define CONFIG_SYS_I2C_PINMUX_CLR (0xFFF0) +#define CONFIG_SYS_I2C_PINMUX_SET (0x000F) #ifdef CONFIG_MCFFEC #define CONFIG_ETHADDR 00:06:3b:01:41:55 #define CONFIG_ETH1ADDR 00:0e:0c:bc:e5:60 #endif -#define CFG_PROMPT "-> " -#define CFG_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "-> " +#define CONFIG_SYS_LONGHELP /* undef to save memory */ #if (CONFIG_CMD_KGDB) -# define CFG_CBSIZE 1024 +# define CONFIG_SYS_CBSIZE 1024 #else -# define CFG_CBSIZE 256 +# define CONFIG_SYS_CBSIZE 256 #endif -#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) -#define CFG_MAXARGS 16 -#define CFG_BARGSIZE CFG_CBSIZE +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE -#define CFG_LOAD_ADDR 0x800000 +#define CONFIG_SYS_LOAD_ADDR 0x800000 #define CONFIG_BOOTDELAY 5 #define CONFIG_BOOTCOMMAND "bootm ffe40000" -#define CFG_MEMTEST_START 0x400 -#define CFG_MEMTEST_END 0x380000 +#define CONFIG_SYS_MEMTEST_START 0x400 +#define CONFIG_SYS_MEMTEST_END 0x380000 -#define CFG_HZ 1000 -#define CFG_CLK 150000000 +#define CONFIG_SYS_HZ 1000 +#define CONFIG_SYS_CLK 150000000 /* * Low Level Configuration Settings @@ -155,73 +155,73 @@ * You should know what you are doing if you make changes here. */ -#define CFG_MBAR 0x40000000 +#define CONFIG_SYS_MBAR 0x40000000 /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in DPRAM) */ -#define CFG_INIT_RAM_ADDR 0x20000000 -#define CFG_INIT_RAM_END 0x10000 /* End of used area in internal SRAM */ -#define CFG_GBL_DATA_SIZE 1000 /* bytes reserved for initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 +#define CONFIG_SYS_INIT_RAM_END 0x10000 /* End of used area in internal SRAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 1000 /* bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ -#define CFG_SDRAM_BASE 0x00000000 -#define CFG_SDRAM_SIZE 16 /* SDRAM size in MB */ -#define CFG_FLASH_BASE 0xffe00000 +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */ +#define CONFIG_SYS_FLASH_BASE 0xffe00000 #ifdef CONFIG_MONITOR_IS_IN_RAM -#define CFG_MONITOR_BASE 0x20000 +#define CONFIG_SYS_MONITOR_BASE 0x20000 #else -#define CFG_MONITOR_BASE (CFG_FLASH_BASE + 0x400) +#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) #endif -#define CFG_MONITOR_LEN 0x20000 -#define CFG_MALLOC_LEN (256 << 10) -#define CFG_BOOTPARAMS_LEN 64*1024 +#define CONFIG_SYS_MONITOR_LEN 0x20000 +#define CONFIG_SYS_MALLOC_LEN (256 << 10) +#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization ?? */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial mmap for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial mmap for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ -#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 11 /* max number of sectors on one chip */ -#define CFG_FLASH_ERASE_TOUT 1000 +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 11 /* max number of sectors on one chip */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 1000 -#define CFG_FLASH_CFI 1 +#define CONFIG_SYS_FLASH_CFI 1 #define CONFIG_FLASH_CFI_DRIVER 1 -#define CFG_FLASH_SIZE 0x200000 +#define CONFIG_SYS_FLASH_SIZE 0x200000 /*----------------------------------------------------------------------- * Cache Configuration */ -#define CFG_CACHELINE_SIZE 16 +#define CONFIG_SYS_CACHELINE_SIZE 16 /*----------------------------------------------------------------------- * Memory bank definitions */ -#define CFG_AR0_PRELIM (CFG_FLASH_BASE >> 16) -#define CFG_CR0_PRELIM 0x1980 -#define CFG_MR0_PRELIM 0x001F0001 +#define CONFIG_SYS_AR0_PRELIM (CONFIG_SYS_FLASH_BASE >> 16) +#define CONFIG_SYS_CR0_PRELIM 0x1980 +#define CONFIG_SYS_MR0_PRELIM 0x001F0001 -#define CFG_AR1_PRELIM 0x3000 -#define CFG_CR1_PRELIM 0x1900 -#define CFG_MR1_PRELIM 0x00070001 +#define CONFIG_SYS_AR1_PRELIM 0x3000 +#define CONFIG_SYS_CR1_PRELIM 0x1900 +#define CONFIG_SYS_MR1_PRELIM 0x00070001 /*----------------------------------------------------------------------- * Port configuration */ -#define CFG_FECI2C 0x0FA0 +#define CONFIG_SYS_FECI2C 0x0FA0 #endif /* _M5275EVB_H */ |