diff options
Diffstat (limited to 'include/configs/M5253EVBE.h')
| -rw-r--r-- | include/configs/M5253EVBE.h | 150 |
1 files changed, 69 insertions, 81 deletions
diff --git a/include/configs/M5253EVBE.h b/include/configs/M5253EVBE.h index 6e14ebf..86de97d 100644 --- a/include/configs/M5253EVBE.h +++ b/include/configs/M5253EVBE.h @@ -31,9 +31,9 @@ #define CONFIG_MCFTMR #define CONFIG_MCFUART -#define CFG_UART_PORT (0) +#define CONFIG_SYS_UART_PORT (0) #define CONFIG_BAUDRATE 115200 -#define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } +#define CONFIG_SYS_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } #undef CONFIG_WATCHDOG /* disable watchdog */ @@ -43,13 +43,13 @@ * Environment is embedded in u-boot in the second sector of the flash */ #ifndef CONFIG_MONITOR_IS_IN_RAM -#define CFG_ENV_OFFSET 0x4000 -#define CFG_ENV_SECT_SIZE 0x2000 -#define CFG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_OFFSET 0x4000 +#define CONFIG_ENV_SECT_SIZE 0x2000 +#define CONFIG_ENV_IS_IN_FLASH 1 #else -#define CFG_ENV_ADDR 0xffe04000 -#define CFG_ENV_SECT_SIZE 0x2000 -#define CFG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_ADDR 0xffe04000 +#define CONFIG_ENV_SECT_SIZE 0x2000 +#define CONFIG_ENV_IS_IN_FLASH 1 #endif /* @@ -81,45 +81,45 @@ #define CONFIG_ATAPI #undef CONFIG_LBA48 -#define CFG_IDE_MAXBUS 1 -#define CFG_IDE_MAXDEVICE 2 +#define CONFIG_SYS_IDE_MAXBUS 1 +#define CONFIG_SYS_IDE_MAXDEVICE 2 -#define CFG_ATA_BASE_ADDR (CFG_MBAR2 + 0x800) -#define CFG_ATA_IDE0_OFFSET 0 +#define CONFIG_SYS_ATA_BASE_ADDR (CONFIG_SYS_MBAR2 + 0x800) +#define CONFIG_SYS_ATA_IDE0_OFFSET 0 -#define CFG_ATA_DATA_OFFSET 0xA0 /* Offset for data I/O */ -#define CFG_ATA_REG_OFFSET 0xA0 /* Offset for normal register accesses */ -#define CFG_ATA_ALT_OFFSET 0xC0 /* Offset for alternate registers */ -#define CFG_ATA_STRIDE 4 /* Interval between registers */ +#define CONFIG_SYS_ATA_DATA_OFFSET 0xA0 /* Offset for data I/O */ +#define CONFIG_SYS_ATA_REG_OFFSET 0xA0 /* Offset for normal register accesses */ +#define CONFIG_SYS_ATA_ALT_OFFSET 0xC0 /* Offset for alternate registers */ +#define CONFIG_SYS_ATA_STRIDE 4 /* Interval between registers */ #define _IO_BASE 0 -#define CFG_PROMPT "=> " -#define CFG_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " +#define CONFIG_SYS_LONGHELP /* undef to save memory */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_LOAD_ADDR 0x00100000 +#define CONFIG_SYS_LOAD_ADDR 0x00100000 -#define CFG_MEMTEST_START 0x400 -#define CFG_MEMTEST_END 0x380000 +#define CONFIG_SYS_MEMTEST_START 0x400 +#define CONFIG_SYS_MEMTEST_END 0x380000 -#define CFG_HZ 1000 +#define CONFIG_SYS_HZ 1000 -#undef CFG_PLL_BYPASS /* bypass PLL for test purpose */ -#define CFG_FAST_CLK -#ifdef CFG_FAST_CLK -# define CFG_PLLCR 0x1243E054 -# define CFG_CLK 140000000 +#undef CONFIG_SYS_PLL_BYPASS /* bypass PLL for test purpose */ +#define CONFIG_SYS_FAST_CLK +#ifdef CONFIG_SYS_FAST_CLK +# define CONFIG_SYS_PLLCR 0x1243E054 +# define CONFIG_SYS_CLK 140000000 #else -# define CFG_PLLCR 0x135a4140 -# define CFG_CLK 70000000 +# define CONFIG_SYS_PLLCR 0x135a4140 +# define CONFIG_SYS_CLK 70000000 #endif /* @@ -128,85 +128,73 @@ * You should know what you are doing if you make changes here. */ -#define CFG_MBAR 0x10000000 /* Register Base Addrs */ -#define CFG_MBAR2 0x80000000 /* Module Base Addrs 2 */ +#define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */ +#define CONFIG_SYS_MBAR2 0x80000000 /* Module Base Addrs 2 */ /* * Definitions for initial stack pointer and data area (in DPRAM) */ -#define CFG_INIT_RAM_ADDR 0x20000000 -#define CFG_INIT_RAM_END 0x10000 /* End of used area in internal SRAM */ -#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 +#define CONFIG_SYS_INIT_RAM_END 0x10000 /* End of used area in internal SRAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /* * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ -#define CFG_SDRAM_BASE 0x00000000 -#define CFG_SDRAM_SIZE 8 /* SDRAM size in MB */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_SIZE 8 /* SDRAM size in MB */ #ifdef CONFIG_MONITOR_IS_IN_RAM -#define CFG_MONITOR_BASE 0x20000 +#define CONFIG_SYS_MONITOR_BASE 0x20000 #else -#define CFG_MONITOR_BASE (CFG_FLASH_BASE + 0x400) +#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) #endif -#define CFG_MONITOR_LEN 0x40000 -#define CFG_MALLOC_LEN (256 << 10) -#define CFG_BOOTPARAMS_LEN (64*1024) +#define CONFIG_SYS_MONITOR_LEN 0x40000 +#define CONFIG_SYS_MALLOC_LEN (256 << 10) +#define CONFIG_SYS_BOOTPARAMS_LEN (64*1024) /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization ?? */ -#define CFG_BOOTMAPSZ (CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20)) +#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20)) /* FLASH organization */ -#define CFG_FLASH_BASE 0xffe00000 -#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 35 /* max number of sectors on one chip */ -#define CFG_FLASH_ERASE_TOUT 1000 +#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 35 /* max number of sectors on one chip */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 1000 -#define CFG_FLASH_CFI 1 +#define CONFIG_SYS_FLASH_CFI 1 #define CONFIG_FLASH_CFI_DRIVER 1 -#define CFG_FLASH_SIZE 0x200000 -#define CFG_FLASH_CFI_WIDTH FLASH_CFI_16BIT +#define CONFIG_SYS_FLASH_SIZE 0x200000 +#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT /* Cache Configuration */ -#define CFG_CACHELINE_SIZE 16 +#define CONFIG_SYS_CACHELINE_SIZE 16 /* Port configuration */ -#define CFG_FECI2C 0xF0 +#define CONFIG_SYS_FECI2C 0xF0 -#define CFG_CSAR0 0xFFE0 -#define CFG_CSMR0 0x001F0021 -#define CFG_CSCR0 0x1D80 - -#define CFG_CSAR1 0 -#define CFG_CSMR1 0 -#define CFG_CSCR1 0 - -#define CFG_CSAR2 0 -#define CFG_CSMR2 0 -#define CFG_CSCR2 0 - -#define CFG_CSAR3 0 -#define CFG_CSMR3 0 -#define CFG_CSCR3 0 +#define CONFIG_SYS_CS0_BASE 0xFFE00000 +#define CONFIG_SYS_CS0_MASK 0x001F0021 +#define CONFIG_SYS_CS0_CTRL 0x00001D80 /*----------------------------------------------------------------------- * Port configuration */ -#define CFG_GPIO_FUNC 0x00000008 /* Set gpio pins: none */ -#define CFG_GPIO1_FUNC 0x00df00f0 /* 36-39(SWITCH),48-52(FPGAs),54 */ -#define CFG_GPIO_EN 0x00000008 /* Set gpio output enable */ -#define CFG_GPIO1_EN 0x00c70000 /* Set gpio output enable */ -#define CFG_GPIO_OUT 0x00000008 /* Set outputs to default state */ -#define CFG_GPIO1_OUT 0x00c70000 /* Set outputs to default state */ -#define CFG_GPIO1_LED 0x00400000 /* user led */ +#define CONFIG_SYS_GPIO_FUNC 0x00000008 /* Set gpio pins: none */ +#define CONFIG_SYS_GPIO1_FUNC 0x00df00f0 /* 36-39(SWITCH),48-52(FPGAs),54 */ +#define CONFIG_SYS_GPIO_EN 0x00000008 /* Set gpio output enable */ +#define CONFIG_SYS_GPIO1_EN 0x00c70000 /* Set gpio output enable */ +#define CONFIG_SYS_GPIO_OUT 0x00000008 /* Set outputs to default state */ +#define CONFIG_SYS_GPIO1_OUT 0x00c70000 /* Set outputs to default state */ +#define CONFIG_SYS_GPIO1_LED 0x00400000 /* user led */ #endif /* _M5253EVB_H */ |