diff options
Diffstat (limited to 'include/configs/EXBITGEN.h')
| -rw-r--r-- | include/configs/EXBITGEN.h | 190 |
1 files changed, 0 insertions, 190 deletions
diff --git a/include/configs/EXBITGEN.h b/include/configs/EXBITGEN.h deleted file mode 100644 index 208b599..0000000 --- a/include/configs/EXBITGEN.h +++ /dev/null @@ -1,190 +0,0 @@ -/* - * (C) Copyright 2000-2004 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_405GP 1 /* This is a PPC405GP CPU */ -#define CONFIG_4xx 1 /* ...member of PPC4xx family */ -#define CONFIG_EXBITGEN 1 /* on a Exbit Generic board */ - -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ - -#define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */ - -/* I2C configuration */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_SPEED 40000 /* I2C speed */ -#define CONFIG_SYS_I2C_SLAVE 0x7F /* I2C slave address */ - -/* environment is in EEPROM */ -#define CONFIG_ENV_IS_IN_EEPROM 1 -#undef CONFIG_ENV_IS_IN_FLASH -#undef CONFIG_ENV_IS_IN_NVRAM - -#ifdef CONFIG_ENV_IS_IN_EEPROM -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x56 /* 1010110 */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* 8-bit internal addressing */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 1 /* ... and 1 bit in I2C address */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 /* 4 bytes per page */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 40 /* write takes up to 40 msec */ -#define CONFIG_ENV_OFFSET 4 /* Offset of Environment Sector */ -#define CONFIG_ENV_SIZE 350 /* that is 350 bytes only! */ -#endif - -#define CONFIG_BOOTDELAY 10 /* autoboot after 10 seconds */ -/* Explanation: - autbooting is altogether disabled and cannot be - enabled if CONFIG_BOOTDELAY is negative. - If you want shorter bootdelay, then - - "setenv bootdelay <delay>" to the proper value -*/ - -#define CONFIG_BOOTCOMMAND "bootm 20400000 20800000" - -#define CONFIG_BOOTARGS "root=/dev/ram " \ - "ramdisk_size=32768 " \ - "console=ttyS0,115200 " \ - "ram=128M debug" - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 0 /* PHY address */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_PPC4xx_EMAC -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -/* UART configuration */ -#define CONFIG_SYS_BASE_BAUD 691200 - -/* Default baud rate */ -#define CONFIG_BAUDRATE 115200 - -/* The following table includes the supported baudrates */ -#define CONFIG_SYS_BAUDRATE_TABLE \ - { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ - 57600, 115200, 230400, 460800, 921600 } - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -/*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------- - */ -#undef CONFIG_PCI /* no pci support */ - -/*----------------------------------------------------------------------- - * External peripheral base address - *----------------------------------------------------------------------- - */ -#undef CONFIG_IDE_PCMCIA /* no pcmcia interface required */ -#undef CONFIG_IDE_LED /* no led for ide supported */ -#undef CONFIG_IDE_RESET /* no reset for ide supported */ - -#define CONFIG_SYS_KEY_REG_BASE_ADDR 0xF0100000 -#define CONFIG_SYS_IR_REG_BASE_ADDR 0xF0200000 -#define CONFIG_SYS_FPGA_REG_BASE_ADDR 0xF0300000 - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH0_BASE 0xFFF80000 -#define CONFIG_SYS_FLASH0_SIZE 0x00080000 -#define CONFIG_SYS_FLASH1_BASE 0x20000000 -#define CONFIG_SYS_FLASH1_SIZE 0x02000000 -#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH0_BASE -#define CONFIG_SYS_FLASH_SIZE CONFIG_SYS_FLASH0_SIZE -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_MONITOR_LEN (192 * 1024) /* Reserve 196 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ - -#if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH0_BASE -#define CONFIG_SYS_RAMSTART -#endif - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 5 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#ifdef CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_OFFSET 0x00060000 /* Offset of Environment Sector */ -#define CONFIG_ENV_SIZE 0x00010000 /* Total Size of Environment Sector */ -#define CONFIG_ENV_SECT_SIZE 0x00010000 /* see README - env sector total size */ -#endif - -/* On Chip Memory location/size */ -#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 -#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 - -/* Global info and initial stack */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of on-chip SRAM */ -#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif -#endif /* __CONFIG_H */ |