summaryrefslogtreecommitdiff
path: root/include/configs/EXBITGEN.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs/EXBITGEN.h')
-rw-r--r--include/configs/EXBITGEN.h190
1 files changed, 0 insertions, 190 deletions
diff --git a/include/configs/EXBITGEN.h b/include/configs/EXBITGEN.h
deleted file mode 100644
index 208b599..0000000
--- a/include/configs/EXBITGEN.h
+++ /dev/null
@@ -1,190 +0,0 @@
-/*
- * (C) Copyright 2000-2004
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_405GP 1 /* This is a PPC405GP CPU */
-#define CONFIG_4xx 1 /* ...member of PPC4xx family */
-#define CONFIG_EXBITGEN 1 /* on a Exbit Generic board */
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
-
-#define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */
-
-/* I2C configuration */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_SPEED 40000 /* I2C speed */
-#define CONFIG_SYS_I2C_SLAVE 0x7F /* I2C slave address */
-
-/* environment is in EEPROM */
-#define CONFIG_ENV_IS_IN_EEPROM 1
-#undef CONFIG_ENV_IS_IN_FLASH
-#undef CONFIG_ENV_IS_IN_NVRAM
-
-#ifdef CONFIG_ENV_IS_IN_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x56 /* 1010110 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* 8-bit internal addressing */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 1 /* ... and 1 bit in I2C address */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 /* 4 bytes per page */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 40 /* write takes up to 40 msec */
-#define CONFIG_ENV_OFFSET 4 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 350 /* that is 350 bytes only! */
-#endif
-
-#define CONFIG_BOOTDELAY 10 /* autoboot after 10 seconds */
-/* Explanation:
- autbooting is altogether disabled and cannot be
- enabled if CONFIG_BOOTDELAY is negative.
- If you want shorter bootdelay, then
- - "setenv bootdelay <delay>" to the proper value
-*/
-
-#define CONFIG_BOOTCOMMAND "bootm 20400000 20800000"
-
-#define CONFIG_BOOTARGS "root=/dev/ram " \
- "ramdisk_size=32768 " \
- "console=ttyS0,115200 " \
- "ram=128M debug"
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_PPC4xx_EMAC
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-/* UART configuration */
-#define CONFIG_SYS_BASE_BAUD 691200
-
-/* Default baud rate */
-#define CONFIG_BAUDRATE 115200
-
-/* The following table includes the supported baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE \
- { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
- 57600, 115200, 230400, 460800, 921600 }
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#undef CONFIG_PCI /* no pci support */
-
-/*-----------------------------------------------------------------------
- * External peripheral base address
- *-----------------------------------------------------------------------
- */
-#undef CONFIG_IDE_PCMCIA /* no pcmcia interface required */
-#undef CONFIG_IDE_LED /* no led for ide supported */
-#undef CONFIG_IDE_RESET /* no reset for ide supported */
-
-#define CONFIG_SYS_KEY_REG_BASE_ADDR 0xF0100000
-#define CONFIG_SYS_IR_REG_BASE_ADDR 0xF0200000
-#define CONFIG_SYS_FPGA_REG_BASE_ADDR 0xF0300000
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH0_BASE 0xFFF80000
-#define CONFIG_SYS_FLASH0_SIZE 0x00080000
-#define CONFIG_SYS_FLASH1_BASE 0x20000000
-#define CONFIG_SYS_FLASH1_SIZE 0x02000000
-#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH0_BASE
-#define CONFIG_SYS_FLASH_SIZE CONFIG_SYS_FLASH0_SIZE
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN (192 * 1024) /* Reserve 196 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
-
-#if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH0_BASE
-#define CONFIG_SYS_RAMSTART
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 5 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_OFFSET 0x00060000 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 0x00010000 /* Total Size of Environment Sector */
-#define CONFIG_ENV_SECT_SIZE 0x00010000 /* see README - env sector total size */
-#endif
-
-/* On Chip Memory location/size */
-#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
-#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
-
-/* Global info and initial stack */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of on-chip SRAM */
-#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#endif
-#endif /* __CONFIG_H */