diff options
Diffstat (limited to 'include/configs/EXBITGEN.h')
| -rw-r--r-- | include/configs/EXBITGEN.h | 127 |
1 files changed, 64 insertions, 63 deletions
diff --git a/include/configs/EXBITGEN.h b/include/configs/EXBITGEN.h index 99d1cf2..1dd6e57 100644 --- a/include/configs/EXBITGEN.h +++ b/include/configs/EXBITGEN.h @@ -43,22 +43,22 @@ /* I2C configuration */ #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CFG_I2C_SPEED 40000 /* I2C speed */ -#define CFG_I2C_SLAVE 0x7F /* I2C slave address */ +#define CONFIG_SYS_I2C_SPEED 40000 /* I2C speed */ +#define CONFIG_SYS_I2C_SLAVE 0x7F /* I2C slave address */ /* environment is in EEPROM */ -#define CFG_ENV_IS_IN_EEPROM 1 -#undef CFG_ENV_IS_IN_FLASH -#undef CFG_ENV_IS_IN_NVRAM - -#ifdef CFG_ENV_IS_IN_EEPROM -#define CFG_I2C_EEPROM_ADDR 0x56 /* 1010110 */ -#define CFG_I2C_EEPROM_ADDR_LEN 1 /* 8-bit internal addressing */ -#define CFG_I2C_EEPROM_ADDR_OVERFLOW 1 /* ... and 1 bit in I2C address */ -#define CFG_EEPROM_PAGE_WRITE_BITS 3 /* 4 bytes per page */ -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 40 /* write takes up to 40 msec */ -#define CFG_ENV_OFFSET 4 /* Offset of Environment Sector */ -#define CFG_ENV_SIZE 350 /* that is 350 bytes only! */ +#define CONFIG_ENV_IS_IN_EEPROM 1 +#undef CONFIG_ENV_IS_IN_FLASH +#undef CONFIG_ENV_IS_IN_NVRAM + +#ifdef CONFIG_ENV_IS_IN_EEPROM +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x56 /* 1010110 */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* 8-bit internal addressing */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 1 /* ... and 1 bit in I2C address */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 /* 4 bytes per page */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 40 /* write takes up to 40 msec */ +#define CONFIG_ENV_OFFSET 4 /* Offset of Environment Sector */ +#define CONFIG_ENV_SIZE 350 /* that is 350 bytes only! */ #endif #define CONFIG_BOOTDELAY 10 /* autoboot after 10 seconds */ @@ -77,7 +77,7 @@ "ram=128M debug" #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address */ @@ -88,6 +88,7 @@ */ #define CONFIG_BOOTP_BOOTFILESIZE #define CONFIG_BOOTP_BOOTPATH +#define CONFIG_PPC4xx_EMAC #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME @@ -103,37 +104,37 @@ /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ /* UART configuration */ -#define CFG_BASE_BAUD 691200 +#define CONFIG_SYS_BASE_BAUD 691200 /* Default baud rate */ #define CONFIG_BAUDRATE 115200 /* The following table includes the supported baudrates */ -#define CFG_BAUDRATE_TABLE \ +#define CONFIG_SYS_BAUDRATE_TABLE \ { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ 57600, 115200, 230400, 460800, 921600 } -#define CFG_CLKS_IN_HZ 1 /* everything, incl board info, in Hz */ +#define CONFIG_SYS_CLKS_IN_HZ 1 /* everything, incl board info, in Hz */ -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ /*----------------------------------------------------------------------- * PCI stuff @@ -149,28 +150,28 @@ #undef CONFIG_IDE_LED /* no led for ide supported */ #undef CONFIG_IDE_RESET /* no reset for ide supported */ -#define CFG_KEY_REG_BASE_ADDR 0xF0100000 -#define CFG_IR_REG_BASE_ADDR 0xF0200000 -#define CFG_FPGA_REG_BASE_ADDR 0xF0300000 +#define CONFIG_SYS_KEY_REG_BASE_ADDR 0xF0100000 +#define CONFIG_SYS_IR_REG_BASE_ADDR 0xF0200000 +#define CONFIG_SYS_FPGA_REG_BASE_ADDR 0xF0300000 /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ -#define CFG_SDRAM_BASE 0x00000000 -#define CFG_FLASH0_BASE 0xFFF80000 -#define CFG_FLASH0_SIZE 0x00080000 -#define CFG_FLASH1_BASE 0x20000000 -#define CFG_FLASH1_SIZE 0x02000000 -#define CFG_FLASH_BASE CFG_FLASH0_BASE -#define CFG_FLASH_SIZE CFG_FLASH0_SIZE -#define CFG_MONITOR_BASE TEXT_BASE -#define CFG_MONITOR_LEN (192 * 1024) /* Reserve 196 kB for Monitor */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ - -#if CFG_MONITOR_BASE < CFG_FLASH0_BASE -#define CFG_RAMSTART +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_FLASH0_BASE 0xFFF80000 +#define CONFIG_SYS_FLASH0_SIZE 0x00080000 +#define CONFIG_SYS_FLASH1_BASE 0x20000000 +#define CONFIG_SYS_FLASH1_SIZE 0x02000000 +#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH0_BASE +#define CONFIG_SYS_FLASH_SIZE CONFIG_SYS_FLASH0_SIZE +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE +#define CONFIG_SYS_MONITOR_LEN (192 * 1024) /* Reserve 196 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ + +#if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH0_BASE +#define CONFIG_SYS_RAMSTART #endif /* @@ -178,32 +179,32 @@ * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ -#define CFG_MAX_FLASH_BANKS 5 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ +#define CONFIG_SYS_MAX_FLASH_BANKS 5 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ -#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ -#ifdef CFG_ENV_IS_IN_FLASH -#define CFG_ENV_OFFSET 0x00060000 /* Offset of Environment Sector */ -#define CFG_ENV_SIZE 0x00010000 /* Total Size of Environment Sector */ -#define CFG_ENV_SECT_SIZE 0x00010000 /* see README - env sector total size */ +#ifdef CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_OFFSET 0x00060000 /* Offset of Environment Sector */ +#define CONFIG_ENV_SIZE 0x00010000 /* Total Size of Environment Sector */ +#define CONFIG_ENV_SECT_SIZE 0x00010000 /* see README - env sector total size */ #endif /* On Chip Memory location/size */ -#define CFG_OCM_DATA_ADDR 0xF8000000 -#define CFG_OCM_DATA_SIZE 0x1000 +#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 +#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 /* Global info and initial stack */ -#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of on-chip SRAM */ -#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */ -#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of on-chip SRAM */ +#define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /* * Internal Definitions |