diff options
Diffstat (limited to 'include/configs/DU440.h')
| -rw-r--r-- | include/configs/DU440.h | 415 |
1 files changed, 0 insertions, 415 deletions
diff --git a/include/configs/DU440.h b/include/configs/DU440.h deleted file mode 100644 index be5494b..0000000 --- a/include/configs/DU440.h +++ /dev/null @@ -1,415 +0,0 @@ -/* - * (C) Copyright 2008 - * Matthias Fuchs, esd gmbh, matthias.fuchs@esd-electronics.com - * - * based on the Sequoia board configuration by - * Stefan Roese, Jacqueline Pira-Ferriol and Alain Saurel - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - ********************************************************************** - * DU440.h - configuration for esd's DU440 board (Power PC440EPx) - ********************************************************************** - */ -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ -#define CONFIG_DU440 1 /* Board is esd DU440 */ -#define CONFIG_440EPX 1 /* Specific PPC440EPx */ -#define CONFIG_SYS_CLK_FREQ 33333400 /* external freq to pll */ - -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xFFFA0000 -#endif - -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ -#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ -#define CONFIG_LAST_STAGE_INIT 1 /* last_stage_init */ - -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (8 << 20) /* Reserve 8 MB for malloc() */ - -#define CONFIG_SYS_BOOT_BASE_ADDR 0xf0000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */ -#define CONFIG_SYS_FLASH_BASE 0xfc000000 /* start of FLASH */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_NAND0_ADDR 0xd0000000 /* NAND Flash */ -#define CONFIG_SYS_NAND1_ADDR 0xd0100000 /* NAND Flash */ -#define CONFIG_SYS_OCM_BASE 0xe0010000 /* ocm */ -#define CONFIG_SYS_PCI_BASE 0xe0000000 /* Internal PCI regs */ -#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ -#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000 -#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000 -#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000 -#define CONFIG_SYS_PCI_IOBASE 0xe8000000 -#define CONFIG_SYS_PCI_SUBSYS_VENDORID PCI_VENDOR_ID_ESDGMBH -#define CONFIG_SYS_PCI_SUBSYS_ID 0x0444 /* device ID for DU440 */ - -#define CONFIG_SYS_USB2D0_BASE 0xe0000100 -#define CONFIG_SYS_USB_DEVICE 0xe0000000 -#define CONFIG_SYS_USB_HOST 0xe0000400 - -/* - * Initial RAM & stack pointer - */ -/* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */ -#define CONFIG_SYS_INIT_RAM_OCM 1 /* OCM as init ram */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE /* OCM */ - -#define CONFIG_SYS_INIT_RAM_SIZE (4 << 10) -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/* - * Serial Port - */ -#define CONFIG_CONS_INDEX 1 /* Use UART0 */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_serial_clock() -#undef CONFIG_SYS_EXT_SERIAL_CLOCK -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - -/* - * Video Port - */ -#define CONFIG_VIDEO -#define CONFIG_VIDEO_SMI_LYNXEM -#define CONFIG_CFB_CONSOLE -#define CONFIG_VIDEO_LOGO -#define CONFIG_VGA_AS_SINGLE_DEVICE -#define CONFIG_SPLASH_SCREEN -#define CONFIG_SPLASH_SCREEN_ALIGN -#define CONFIG_VIDEO_BMP_GZIP /* gzip compressed bmp images */ -#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (4 << 20) /* for decompressed img */ -#define CONFIG_SYS_DEFAULT_VIDEO_MODE 0x31a /* 1280x1024,16bpp */ -#define CONFIG_SYS_CONSOLE_IS_IN_ENV -#define CONFIG_SYS_ISA_IO CONFIG_SYS_PCI_IOBASE - -/* - * Environment - */ -#define CONFIG_ENV_IS_IN_EEPROM 1 /* use FLASH for environment vars */ - -/* - * FLASH related - */ -#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ -#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ - -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -/* CFI_FLASH_PROTECTION make flash_protect hang sometimes -> disabled */ -#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware flash protection */ - -#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ - -#ifdef CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ -#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) -#endif - -#ifdef CONFIG_ENV_IS_IN_EEPROM -#define CONFIG_ENV_OFFSET 0 /* environment starts at */ - /* the beginning of the EEPROM */ -#define CONFIG_ENV_SIZE 0x1000 /* 4096 bytes may be used for env vars */ -#endif - -/* - * DDR SDRAM - */ -#define CONFIG_SYS_MBYTES_SDRAM (1024) /* 512 MiB TODO: remove */ -#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */ -#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */ - /* 440EPx errata CHIP 11 */ -#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */ -#define CONFIG_DDR_ECC /* Use ECC when available */ -#define SPD_EEPROM_ADDRESS {0x50} -#define CONFIG_PROG_SDRAM_TLB - -/* - * I2C - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_PPC4XX -#define CONFIG_SYS_I2C_PPC4XX_CH0 -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F -#define CONFIG_SYS_I2C_PPC4XX_CH1 -#define CONFIG_SYS_I2C_PPC4XX_SPEED_1 100000 -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_1 0x7F - -#define CONFIG_SYS_SPD_BUS_NUM 0 -#define IIC1_MCP3021_ADDR 0x4d -#define IIC1_USB2507_ADDR 0x2c -#define CONFIG_SYS_I2C_NOPROBES { {1, IIC1_USB2507_ADDR} } - -#define CONFIG_SYS_I2C_MULTI_EEPROMS -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 -#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x01 - -#define CONFIG_SYS_EEPROM_WREN 1 -#define CONFIG_SYS_I2C_BOOT_EEPROM_ADDR 0x52 - -/* - * standard dtt sensor configuration - bottom bit will determine local or - * remote sensor of the TMP401 - */ -#define CONFIG_DTT_SENSORS { 0, 1 } - -/* - * The PMC440 uses a TI TMP401 temperature sensor. This part - * is basically compatible to the ADM1021 that is supported - * by U-Boot. - * - * - i2c addr 0x4c - * - conversion rate 0x02 = 0.25 conversions/second - * - ALERT ouput disabled - * - local temp sensor enabled, min set to 0 deg, max set to 70 deg - * - remote temp sensor enabled, min set to 0 deg, max set to 70 deg - */ -#define CONFIG_DTT_ADM1021 -#define CONFIG_SYS_DTT_ADM1021 { { 0x4c, 0x02, 0, 1, 70, 0, 1, 70, 0} } - -/* - * RTC stuff - */ -#define CONFIG_RTC_DS1338 -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "ethrotate=no\0" \ - "hostname=du440\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_self=run ramargs addip addtty optargs;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${img};run nfsargs addip addtty optargs;" \ - "bootm\0" \ - "rootpath=/tftpboot/du440/target_root_du440\0" \ - "img=/tftpboot/du440/uImage\0" \ - "kernel_addr=FFC00000\0" \ - "ramdisk_addr=FFE00000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 100000 /tftpboot/du440/u-boot.bin\0" \ - "update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;" \ - "cp.b 100000 FFFA0000 60000\0" \ - "" - -#define CONFIG_PREBOOT /* enable preboot variable */ - -#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#ifndef __ASSEMBLY__ -int du440_phy_addr(int devnum); -#endif - -#define CONFIG_PPC4xx_EMAC -#define CONFIG_IBM_EMAC4_V4 1 -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR du440_phy_addr(0) /* PHY address */ - -#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ -#undef CONFIG_PHY_GIGE /* no GbE detection */ - -#define CONFIG_HAS_ETH0 -#define CONFIG_SYS_RX_ETH_BUFFER 128 - -#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ -#define CONFIG_PHY1_ADDR du440_phy_addr(1) - -/* - * USB - */ -#define CONFIG_USB_OHCI_NEW -#define CONFIG_USB_STORAGE -#define CONFIG_SYS_OHCI_BE_CONTROLLER - -#define CONFIG_SYS_USB_OHCI_CPU_INIT 1 -#define CONFIG_SYS_USB_OHCI_REGS_BASE CONFIG_SYS_USB_HOST -#define CONFIG_SYS_USB_OHCI_SLOT_NAME "du440" -#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 - -/* Comment this out to enable USB 1.1 device */ -#define USB_2_0_DEVICE - -/* Partitions */ -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION - -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_BMP -#define CONFIG_CMD_BSP -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_DTT -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NAND -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS -#define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_SDRAM -#define CONFIG_CMD_SOURCE -#define CONFIG_CMD_USB - -#define CONFIG_SUPPORT_VFAT - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x3f000000 /* 4 ... < 1GB DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - -#define CONFIG_AUTOBOOT_KEYED 1 -#define CONFIG_AUTOBOOT_PROMPT \ - "Press SPACE to abort autoboot in %d seconds\n", bootdelay -#define CONFIG_AUTOBOOT_DELAY_STR "d" -#define CONFIG_AUTOBOOT_STOP_STR " " - -/* - * PCI stuff - */ -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_PCI_PNP /* do (not) pci plug-and-play */ -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE*/ - -/* Board-specific PCI */ -#define CONFIG_SYS_PCI_TARGET_INIT -#define CONFIG_SYS_PCI_MASTER_INIT - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * External Bus Controller (EBC) Setup - */ -#define CONFIG_SYS_FLASH CONFIG_SYS_FLASH_BASE - -#define CONFIG_SYS_CPLD_BASE 0xC0000000 -#define CONFIG_SYS_CPLD_RANGE 0x00000010 -#define CONFIG_SYS_DUMEM_BASE 0xC0100000 -#define CONFIG_SYS_DUMEM_RANGE 0x00100000 -#define CONFIG_SYS_DUIO_BASE 0xC0200000 -#define CONFIG_SYS_DUIO_RANGE 0x00010000 - -#define CONFIG_SYS_NAND0_CS 2 /* NAND chip connected to CSx */ -#define CONFIG_SYS_NAND1_CS 3 /* NAND chip connected to CSx */ -/* Memory Bank 0 (NOR-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB0AP 0x04017200 -#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH_BASE | 0xda000) - -/* Memory Bank 1 (CPLD, 16 bytes needed, but 1MB is minimum) */ -#define CONFIG_SYS_EBC_PB1AP 0x018003c0 -#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_CPLD_BASE | 0x18000) - -/* Memory Bank 2 (NAND-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB2AP 0x018003c0 -#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_NAND0_ADDR | 0x1c000) - -/* Memory Bank 3 (NAND-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB3AP 0x018003c0 -#define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_NAND1_ADDR | 0x1c000) - -/* Memory Bank 4 (DUMEM, 1MB) initialization */ -#define CONFIG_SYS_EBC_PB4AP 0x018053c0 -#define CONFIG_SYS_EBC_PB4CR (CONFIG_SYS_DUMEM_BASE | 0x18000) - -/* Memory Bank 5 (DUIO, 64KB needed, but 1MB is minimum) */ -#define CONFIG_SYS_EBC_PB5AP 0x018053c0 -#define CONFIG_SYS_EBC_PB5CR (CONFIG_SYS_DUIO_BASE | 0x18000) - -/* - * NAND FLASH - */ -#define CONFIG_SYS_MAX_NAND_DEVICE 2 -#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ -#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND0_ADDR + CONFIG_SYS_NAND0_CS, \ - CONFIG_SYS_NAND1_ADDR + CONFIG_SYS_NAND1_CS} - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif - -#define CONFIG_SOURCE 1 - -#define CONFIG_OF_LIBFDT -#define CONFIG_OF_BOARD_SETUP - -#endif /* __CONFIG_H */ |