summaryrefslogtreecommitdiff
path: root/include/configs/DU440.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs/DU440.h')
-rw-r--r--include/configs/DU440.h216
1 files changed, 108 insertions, 108 deletions
diff --git a/include/configs/DU440.h b/include/configs/DU440.h
index c408e43..508a0ca 100644
--- a/include/configs/DU440.h
+++ b/include/configs/DU440.h
@@ -45,52 +45,52 @@
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
-#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
-#define CFG_MALLOC_LEN (8 << 20) /* Reserve 8 MB for malloc() */
-
-#define CFG_BOOT_BASE_ADDR 0xf0000000
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
-#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */
-#define CFG_MONITOR_BASE TEXT_BASE
-#define CFG_NAND0_ADDR 0xd0000000 /* NAND Flash */
-#define CFG_NAND1_ADDR 0xd0100000 /* NAND Flash */
-#define CFG_OCM_BASE 0xe0010000 /* ocm */
-#define CFG_PCI_BASE 0xe0000000 /* Internal PCI regs */
-#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */
-#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000
-#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000
-#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000
-#define CFG_PCI_IOBASE 0xe8000000
+#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (8 << 20) /* Reserve 8 MB for malloc() */
+
+#define CONFIG_SYS_BOOT_BASE_ADDR 0xf0000000
+#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */
+#define CONFIG_SYS_FLASH_BASE 0xfc000000 /* start of FLASH */
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
+#define CONFIG_SYS_NAND0_ADDR 0xd0000000 /* NAND Flash */
+#define CONFIG_SYS_NAND1_ADDR 0xd0100000 /* NAND Flash */
+#define CONFIG_SYS_OCM_BASE 0xe0010000 /* ocm */
+#define CONFIG_SYS_PCI_BASE 0xe0000000 /* Internal PCI regs */
+#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */
+#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000
+#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000
+#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000
+#define CONFIG_SYS_PCI_IOBASE 0xe8000000
/* Don't change either of these */
-#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals */
+#define CONFIG_SYS_PERIPHERAL_BASE 0xef600000 /* internal peripherals */
-#define CFG_USB2D0_BASE 0xe0000100
-#define CFG_USB_DEVICE 0xe0000000
-#define CFG_USB_HOST 0xe0000400
+#define CONFIG_SYS_USB2D0_BASE 0xe0000100
+#define CONFIG_SYS_USB_DEVICE 0xe0000000
+#define CONFIG_SYS_USB_HOST 0xe0000400
/*
* Initial RAM & stack pointer
*/
/* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */
-#define CFG_INIT_RAM_OCM 1 /* OCM as init ram */
-#define CFG_INIT_RAM_ADDR CFG_OCM_BASE /* OCM */
+#define CONFIG_SYS_INIT_RAM_OCM 1 /* OCM as init ram */
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE /* OCM */
-#define CFG_INIT_RAM_END (4 << 10)
-#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_RAM_END (4 << 10)
+#define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*
* Serial Port
*/
-#undef CFG_EXT_SERIAL_CLOCK
+#undef CONFIG_SYS_EXT_SERIAL_CLOCK
#define CONFIG_BAUDRATE 115200
#define CONFIG_SERIAL_MULTI 1
#undef CONFIG_UART1_CONSOLE
-#define CFG_BAUDRATE_TABLE \
+#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
/*
@@ -104,10 +104,10 @@
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SPLASH_SCREEN_ALIGN
#define CONFIG_VIDEO_BMP_GZIP /* gzip compressed bmp images */
-#define CFG_VIDEO_LOGO_MAX_SIZE (4 << 20) /* for decompressed img */
-#define CFG_DEFAULT_VIDEO_MODE 0x31a /* 1280x1024,16bpp */
-#define CFG_CONSOLE_IS_IN_ENV
-#define CFG_ISA_IO CFG_PCI_IOBASE
+#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (4 << 20) /* for decompressed img */
+#define CONFIG_SYS_DEFAULT_VIDEO_MODE 0x31a /* 1280x1024,16bpp */
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define CONFIG_SYS_ISA_IO CONFIG_SYS_PCI_IOBASE
/*
* Environment
@@ -117,27 +117,27 @@
/*
* FLASH related
*/
-#define CFG_FLASH_CFI /* The flash is CFI compatible */
+#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
-#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE }
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
/* CFI_FLASH_PROTECTION make flash_protect hang sometimes -> disabled */
-#define CFG_FLASH_PROTECTION 1 /* use hardware flash protection */
+#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware flash protection */
-#define CFG_FLASH_EMPTY_INFO
-#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
#ifdef CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
-#define CONFIG_ENV_ADDR ((-CFG_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
@@ -154,9 +154,9 @@
/*
* DDR SDRAM
*/
-#define CFG_MBYTES_SDRAM (1024) /* 512 MiB TODO: remove */
+#define CONFIG_SYS_MBYTES_SDRAM (1024) /* 512 MiB TODO: remove */
#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */
-#define CFG_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */
+#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */
/* 440EPx errata CHIP 11 */
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */
#define CONFIG_DDR_ECC /* Use ECC when available */
@@ -168,26 +168,26 @@
*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
#define CONFIG_I2C_CMD_TREE 1
#define CONFIG_I2C_MULTI_BUS 1
-#define CFG_SPD_BUS_NUM 0
+#define CONFIG_SYS_SPD_BUS_NUM 0
#define IIC1_MCP3021_ADDR 0x4d
#define IIC1_USB2507_ADDR 0x2c
#ifdef CONFIG_I2C_MULTI_BUS
-#define CFG_I2C_NOPROBES {{1, IIC1_USB2507_ADDR}}
+#define CONFIG_SYS_I2C_NOPROBES {{1, IIC1_USB2507_ADDR}}
#endif
-#define CFG_I2C_MULTI_EEPROMS
-#define CFG_I2C_EEPROM_ADDR 0x54
-#define CFG_I2C_EEPROM_ADDR_LEN 2
-#define CFG_EEPROM_PAGE_WRITE_BITS 5
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
-#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x01
+#define CONFIG_SYS_I2C_MULTI_EEPROMS
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
+#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x01
-#define CFG_EEPROM_WREN 1
-#define CFG_I2C_BOOT_EEPROM_ADDR 0x52
+#define CONFIG_SYS_EEPROM_WREN 1
+#define CONFIG_SYS_I2C_BOOT_EEPROM_ADDR 0x52
/*
* standard dtt sensor configuration - bottom bit will determine local or
@@ -207,13 +207,13 @@
* - remote temp sensor enabled, min set to 0 deg, max set to 70 deg
*/
#define CONFIG_DTT_ADM1021
-#define CFG_DTT_ADM1021 { { 0x4c, 0x02, 0, 1, 70, 0, 1, 70, 0} }
+#define CONFIG_SYS_DTT_ADM1021 { { 0x4c, 0x02, 0, 1, 70, 0, 1, 70, 0} }
/*
* RTC stuff
*/
#define CONFIG_RTC_DS1338
-#define CFG_I2C_RTC_ADDR 0x68
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
#undef CONFIG_BOOTARGS
@@ -247,7 +247,7 @@
#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#ifndef __ASSEMBLY__
int du440_phy_addr(int devnum);
@@ -261,7 +261,7 @@ int du440_phy_addr(int devnum);
#undef CONFIG_PHY_GIGE /* no GbE detection */
#define CONFIG_HAS_ETH0
-#define CFG_RX_ETH_BUFFER 128
+#define CONFIG_SYS_RX_ETH_BUFFER 128
#define CONFIG_NET_MULTI 1
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
@@ -272,12 +272,12 @@ int du440_phy_addr(int devnum);
*/
#define CONFIG_USB_OHCI_NEW
#define CONFIG_USB_STORAGE
-#define CFG_OHCI_BE_CONTROLLER
+#define CONFIG_SYS_OHCI_BE_CONTROLLER
-#define CFG_USB_OHCI_CPU_INIT 1
-#define CFG_USB_OHCI_REGS_BASE CFG_USB_HOST
-#define CFG_USB_OHCI_SLOT_NAME "du440"
-#define CFG_USB_OHCI_MAX_ROOT_PORTS 15
+#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
+#define CONFIG_SYS_USB_OHCI_REGS_BASE CONFIG_SYS_USB_HOST
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME "du440"
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
/* Comment this out to enable USB 1.1 device */
#define USB_2_0_DEVICE
@@ -317,25 +317,25 @@ int du440_phy_addr(int devnum);
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
/* Print Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x00400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x3f000000 /* 4 ... < 1GB DRAM */
+#define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x3f000000 /* 4 ... < 1GB DRAM */
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_LOOPW 1 /* enable loopw command */
@@ -355,65 +355,65 @@ int du440_phy_addr(int devnum);
#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_PNP /* do (not) pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/
+#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE*/
/* Board-specific PCI */
-#define CFG_PCI_TARGET_INIT
-#define CFG_PCI_MASTER_INIT
+#define CONFIG_SYS_PCI_TARGET_INIT
+#define CONFIG_SYS_PCI_MASTER_INIT
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*
* External Bus Controller (EBC) Setup
*/
-#define CFG_FLASH CFG_FLASH_BASE
+#define CONFIG_SYS_FLASH CONFIG_SYS_FLASH_BASE
-#define CFG_CPLD_BASE 0xC0000000
-#define CFG_CPLD_RANGE 0x00000010
-#define CFG_DUMEM_BASE 0xC0100000
-#define CFG_DUMEM_RANGE 0x00100000
-#define CFG_DUIO_BASE 0xC0200000
-#define CFG_DUIO_RANGE 0x00010000
+#define CONFIG_SYS_CPLD_BASE 0xC0000000
+#define CONFIG_SYS_CPLD_RANGE 0x00000010
+#define CONFIG_SYS_DUMEM_BASE 0xC0100000
+#define CONFIG_SYS_DUMEM_RANGE 0x00100000
+#define CONFIG_SYS_DUIO_BASE 0xC0200000
+#define CONFIG_SYS_DUIO_RANGE 0x00010000
-#define CFG_NAND0_CS 2 /* NAND chip connected to CSx */
-#define CFG_NAND1_CS 3 /* NAND chip connected to CSx */
+#define CONFIG_SYS_NAND0_CS 2 /* NAND chip connected to CSx */
+#define CONFIG_SYS_NAND1_CS 3 /* NAND chip connected to CSx */
/* Memory Bank 0 (NOR-FLASH) initialization */
-#define CFG_EBC_PB0AP 0x04017200
-#define CFG_EBC_PB0CR (CFG_FLASH_BASE | 0xda000)
+#define CONFIG_SYS_EBC_PB0AP 0x04017200
+#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH_BASE | 0xda000)
/* Memory Bank 1 (CPLD, 16 bytes needed, but 1MB is minimum) */
-#define CFG_EBC_PB1AP 0x018003c0
-#define CFG_EBC_PB1CR (CFG_CPLD_BASE | 0x18000)
+#define CONFIG_SYS_EBC_PB1AP 0x018003c0
+#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_CPLD_BASE | 0x18000)
/* Memory Bank 2 (NAND-FLASH) initialization */
-#define CFG_EBC_PB2AP 0x018003c0
-#define CFG_EBC_PB2CR (CFG_NAND0_ADDR | 0x1c000)
+#define CONFIG_SYS_EBC_PB2AP 0x018003c0
+#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_NAND0_ADDR | 0x1c000)
/* Memory Bank 3 (NAND-FLASH) initialization */
-#define CFG_EBC_PB3AP 0x018003c0
-#define CFG_EBC_PB3CR (CFG_NAND1_ADDR | 0x1c000)
+#define CONFIG_SYS_EBC_PB3AP 0x018003c0
+#define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_NAND1_ADDR | 0x1c000)
/* Memory Bank 4 (DUMEM, 1MB) initialization */
-#define CFG_EBC_PB4AP 0x018053c0
-#define CFG_EBC_PB4CR (CFG_DUMEM_BASE | 0x18000)
+#define CONFIG_SYS_EBC_PB4AP 0x018053c0
+#define CONFIG_SYS_EBC_PB4CR (CONFIG_SYS_DUMEM_BASE | 0x18000)
/* Memory Bank 5 (DUIO, 64KB needed, but 1MB is minimum) */
-#define CFG_EBC_PB5AP 0x018053c0
-#define CFG_EBC_PB5CR (CFG_DUIO_BASE | 0x18000)
+#define CONFIG_SYS_EBC_PB5AP 0x018053c0
+#define CONFIG_SYS_EBC_PB5CR (CONFIG_SYS_DUIO_BASE | 0x18000)
/*
* NAND FLASH
*/
-#define CFG_MAX_NAND_DEVICE 2
-#define NAND_MAX_CHIPS CFG_MAX_NAND_DEVICE
-#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
-#define CFG_NAND_BASE_LIST {CFG_NAND0_ADDR + CFG_NAND0_CS, \
- CFG_NAND1_ADDR + CFG_NAND1_CS}
+#define CONFIG_SYS_MAX_NAND_DEVICE 2
+#define NAND_MAX_CHIPS CONFIG_SYS_MAX_NAND_DEVICE
+#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
+#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND0_ADDR + CONFIG_SYS_NAND0_CS, \
+ CONFIG_SYS_NAND1_ADDR + CONFIG_SYS_NAND1_CS}
/*
* Internal Definitions