diff options
Diffstat (limited to 'include/configs/CPCI4052.h')
| -rw-r--r-- | include/configs/CPCI4052.h | 252 |
1 files changed, 126 insertions, 126 deletions
diff --git a/include/configs/CPCI4052.h b/include/configs/CPCI4052.h index dd2fa7f..6ee5698 100644 --- a/include/configs/CPCI4052.h +++ b/include/configs/CPCI4052.h @@ -34,22 +34,22 @@ */ #define CONFIG_405GP 1 /* This is a PPC405 CPU */ -#define CONFIG_4xx 1 /* ...member of PPC4xx family */ +#define CONFIG_4xx 1 /* ...member of PPC4xx family */ #define CONFIG_CPCI405 1 /* ...on a CPCI405 board */ -#define CONFIG_CPCI405_VER2 1 /* ...version 2 */ +#define CONFIG_CPCI405_VER2 1 /* ...version 2 */ -#define CONFIG_BOARD_PRE_INIT 1 /* call board_pre_init() */ +#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ -#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ +#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ #define CONFIG_BAUDRATE 9600 #define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ #if 0 -#define CONFIG_PREBOOT \ - "crc32 f0207004 ffc 0;" \ - "if cmp 0 f0207000 1;" \ - "then;echo Old CRC is correct;crc32 f0207004 ff4 f0207000;" \ +#define CONFIG_PREBOOT \ + "crc32 f0207004 ffc 0;" \ + "if cmp 0 f0207000 1;" \ + "then;echo Old CRC is correct;crc32 f0207004 ff4 f0207000;" \ "else;echo Old CRC is bad;fi" #endif @@ -68,11 +68,11 @@ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 0 /* PHY address */ +#define CONFIG_PHY_ADDR 0 /* PHY address */ #define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */ -#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \ +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \ CONFIG_BOOTP_DNS | \ CONFIG_BOOTP_DNS2 | \ CONFIG_BOOTP_SEND_HOSTNAME ) @@ -88,7 +88,7 @@ CFG_CMD_I2C | \ CFG_CMD_MII | \ CFG_CMD_PING | \ - CFG_CMD_EEPROM ) + CFG_CMD_EEPROM ) #define CONFIG_MAC_PARTITION #define CONFIG_DOS_PARTITION @@ -96,9 +96,9 @@ /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ #include <cmd_confdefs.h> -#undef CONFIG_WATCHDOG /* watchdog disabled */ +#undef CONFIG_WATCHDOG /* watchdog disabled */ -#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ +#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ /* * Miscellaneous configurable options @@ -108,89 +108,89 @@ #undef CFG_HUSH_PARSER /* use "hush" command parser */ #ifdef CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " +#define CFG_PROMPT_HUSH_PS2 "> " #endif #if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ #define CFG_MAXARGS 16 /* max number of command args */ #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */ +#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */ -#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ +#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ #define CFG_MEMTEST_START 0x0400000 /* memtest works on */ #define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ -#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */ -#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */ -#define CFG_BASE_BAUD 691200 +#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */ +#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */ +#define CFG_BASE_BAUD 691200 /* The following table includes the supported baudrates */ -#define CFG_BAUDRATE_TABLE \ +#define CFG_BAUDRATE_TABLE \ { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ 57600, 115200, 230400, 460800, 921600 } #define CFG_LOAD_ADDR 0x100000 /* default load address */ #define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ +#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ -#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */ +#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */ /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- */ -#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ -#define PCI_HOST_FORCE 1 /* configure as pci host */ -#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ - -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */ -#define CONFIG_PCI_PNP /* do pci plug-and-play */ - /* resource configuration */ - -#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ - -#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/ - -#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ -#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */ -#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */ -#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/ -#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */ -#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */ -#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ -#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ +#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ +#define PCI_HOST_FORCE 1 /* configure as pci host */ +#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ + +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */ +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + /* resource configuration */ + +#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ + +#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/ + +#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ +#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */ +#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */ +#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/ +#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */ +#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */ +#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ +#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */ +#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ +#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ /*----------------------------------------------------------------------- * IDE/ATA stuff *----------------------------------------------------------------------- */ -#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ -#undef CONFIG_IDE_LED /* no led for ide supported */ +#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ +#undef CONFIG_IDE_LED /* no led for ide supported */ #define CONFIG_IDE_RESET 1 /* reset for ide supported */ -#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */ -#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */ +#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */ +#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */ -#define CFG_ATA_BASE_ADDR 0xF0100000 -#define CFG_ATA_IDE0_OFFSET 0x0000 +#define CFG_ATA_BASE_ADDR 0xF0100000 +#define CFG_ATA_IDE0_OFFSET 0x0000 #define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ -#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */ +#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */ #define CFG_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */ /*----------------------------------------------------------------------- @@ -219,21 +219,21 @@ #define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ #define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ -#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */ -#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */ -#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */ +#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */ +#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */ +#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */ /* * The following defines are added for buggy IOP480 byte interface. * All other boards should use the standard values (CPCI405 etc.) */ -#define CFG_FLASH_READ0 0x0000 /* 0 is standard */ -#define CFG_FLASH_READ1 0x0001 /* 1 is standard */ -#define CFG_FLASH_READ2 0x0002 /* 2 is standard */ +#define CFG_FLASH_READ0 0x0000 /* 0 is standard */ +#define CFG_FLASH_READ1 0x0001 /* 1 is standard */ +#define CFG_FLASH_READ2 0x0002 /* 2 is standard */ -#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */ -#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */ +#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */ +#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */ #if 0 /* Use NVRAM for environment variables */ /*----------------------------------------------------------------------- @@ -246,9 +246,9 @@ #else /* Use EEPROM for environment variables */ -#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ -#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */ -#define CFG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars*/ +#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ +#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */ +#define CFG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars*/ /* total size of a CAT24WC16 is 2048 bytes */ #endif @@ -264,20 +264,20 @@ #define CFG_I2C_SLAVE 0x7F #define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ -#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ -/* mask of address bits that overflow into the "EEPROM chip address" */ +#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ +/* mask of address bits that overflow into the "EEPROM chip address" */ #define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07 #define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */ /* 16 byte page write mode using*/ - /* last 4 bits of the address */ + /* last 4 bits of the address */ #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ #define CFG_EEPROM_PAGE_WRITE_ENABLE /*----------------------------------------------------------------------- * Cache Configuration */ -#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */ - /* have only 8kB, 16kB is save here */ +#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */ + /* have only 8kB, 16kB is save here */ #define CFG_CACHELINE_SIZE 32 /* ... */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ @@ -296,89 +296,89 @@ * External Bus Controller (EBC) Setup */ -/* Memory Bank 0 (Flash Bank 0) initialization */ -#define CFG_EBC_PB0AP 0x92015480 -#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */ +/* Memory Bank 0 (Flash Bank 0) initialization */ +#define CFG_EBC_PB0AP 0x92015480 +#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */ -/* Memory Bank 1 (Flash Bank 1) initialization */ -#define CFG_EBC_PB1AP 0x92015480 -#define CFG_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */ +/* Memory Bank 1 (Flash Bank 1) initialization */ +#define CFG_EBC_PB1AP 0x92015480 +#define CFG_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */ -/* Memory Bank 2 (CAN0, 1) initialization */ -#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ -#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */ -#define CFG_LED_ADDR 0xF0000380 +/* Memory Bank 2 (CAN0, 1) initialization */ +#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ +#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */ +#define CFG_LED_ADDR 0xF0000380 -/* Memory Bank 3 (CompactFlash IDE) initialization */ -#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ -#define CFG_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */ +/* Memory Bank 3 (CompactFlash IDE) initialization */ +#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ +#define CFG_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */ -/* Memory Bank 4 (NVRAM/RTC) initialization */ -/*#define CFG_EBC_PB4AP 0x01805280 / * TWT=3,WBN=1,WBF=1,TH=1,SOR=1 */ -#define CFG_EBC_PB4AP 0x01805680 /* TWT=3,WBN=1,WBF=1,TH=3,SOR=1 */ -#define CFG_EBC_PB4CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */ +/* Memory Bank 4 (NVRAM/RTC) initialization */ +/*#define CFG_EBC_PB4AP 0x01805280 / * TWT=3,WBN=1,WBF=1,TH=1,SOR=1 */ +#define CFG_EBC_PB4AP 0x01805680 /* TWT=3,WBN=1,WBF=1,TH=3,SOR=1 */ +#define CFG_EBC_PB4CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */ -/* Memory Bank 5 (optional Quart) initialization */ -#define CFG_EBC_PB5AP 0x04005B80 /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/ -#define CFG_EBC_PB5CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */ +/* Memory Bank 5 (optional Quart) initialization */ +#define CFG_EBC_PB5AP 0x04005B80 /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/ +#define CFG_EBC_PB5CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */ -/* Memory Bank 6 (FPGA internal) initialization */ -#define CFG_EBC_PB6AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ -#define CFG_EBC_PB6CR 0xF041A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */ -#define CFG_FPGA_BASE_ADDR 0xF0400000 +/* Memory Bank 6 (FPGA internal) initialization */ +#define CFG_EBC_PB6AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ +#define CFG_EBC_PB6CR 0xF041A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */ +#define CFG_FPGA_BASE_ADDR 0xF0400000 /*----------------------------------------------------------------------- * FPGA stuff */ /* FPGA internal regs */ -#define CFG_FPGA_MODE 0x00 -#define CFG_FPGA_STATUS 0x02 -#define CFG_FPGA_TS 0x04 -#define CFG_FPGA_TS_LOW 0x06 -#define CFG_FPGA_TS_CAP0 0x10 -#define CFG_FPGA_TS_CAP0_LOW 0x12 -#define CFG_FPGA_TS_CAP1 0x14 -#define CFG_FPGA_TS_CAP1_LOW 0x16 -#define CFG_FPGA_TS_CAP2 0x18 -#define CFG_FPGA_TS_CAP2_LOW 0x1a -#define CFG_FPGA_TS_CAP3 0x1c -#define CFG_FPGA_TS_CAP3_LOW 0x1e +#define CFG_FPGA_MODE 0x00 +#define CFG_FPGA_STATUS 0x02 +#define CFG_FPGA_TS 0x04 +#define CFG_FPGA_TS_LOW 0x06 +#define CFG_FPGA_TS_CAP0 0x10 +#define CFG_FPGA_TS_CAP0_LOW 0x12 +#define CFG_FPGA_TS_CAP1 0x14 +#define CFG_FPGA_TS_CAP1_LOW 0x16 +#define CFG_FPGA_TS_CAP2 0x18 +#define CFG_FPGA_TS_CAP2_LOW 0x1a +#define CFG_FPGA_TS_CAP3 0x1c +#define CFG_FPGA_TS_CAP3_LOW 0x1e /* FPGA Mode Reg */ -#define CFG_FPGA_MODE_CF_RESET 0x0001 +#define CFG_FPGA_MODE_CF_RESET 0x0001 #define CFG_FPGA_MODE_DUART_RESET 0x0002 #define CFG_FPGA_MODE_ENABLE_OUTPUT 0x0004 /* only set on CPCI-405 Ver 3 */ #define CFG_FPGA_MODE_TS_IRQ_ENABLE 0x0100 #define CFG_FPGA_MODE_TS_IRQ_CLEAR 0x1000 -#define CFG_FPGA_MODE_TS_CLEAR 0x2000 +#define CFG_FPGA_MODE_TS_CLEAR 0x2000 /* FPGA Status Reg */ -#define CFG_FPGA_STATUS_DIP0 0x0001 -#define CFG_FPGA_STATUS_DIP1 0x0002 -#define CFG_FPGA_STATUS_DIP2 0x0004 -#define CFG_FPGA_STATUS_FLASH 0x0008 -#define CFG_FPGA_STATUS_TS_IRQ 0x1000 +#define CFG_FPGA_STATUS_DIP0 0x0001 +#define CFG_FPGA_STATUS_DIP1 0x0002 +#define CFG_FPGA_STATUS_DIP2 0x0004 +#define CFG_FPGA_STATUS_FLASH 0x0008 +#define CFG_FPGA_STATUS_TS_IRQ 0x1000 -#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */ -#define CFG_FPGA_MAX_SIZE 32*1024 /* 32kByte is enough for XC2S15 */ +#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */ +#define CFG_FPGA_MAX_SIZE 32*1024 /* 32kByte is enough for XC2S15 */ /* FPGA program pin configuration */ -#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */ -#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */ -#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */ -#define CFG_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */ -#define CFG_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */ +#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */ +#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */ +#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */ +#define CFG_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */ +#define CFG_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */ /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in data cache) */ -#define CFG_INIT_DCACHE_CS 7 /* use cs # 7 for data cache memory */ +#define CFG_INIT_DCACHE_CS 7 /* use cs # 7 for data cache memory */ -#define CFG_INIT_RAM_ADDR 0x40000000 /* use data cache */ -#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */ +#define CFG_INIT_RAM_ADDR 0x40000000 /* use data cache */ +#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */ #define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET /* |