diff options
Diffstat (limited to 'include/configs/BC3450.h')
| -rw-r--r-- | include/configs/BC3450.h | 104 |
1 files changed, 52 insertions, 52 deletions
diff --git a/include/configs/BC3450.h b/include/configs/BC3450.h index a79de40..5b54f30 100644 --- a/include/configs/BC3450.h +++ b/include/configs/BC3450.h @@ -42,21 +42,21 @@ #define CONFIG_MPC5200 1 /* (more precisely a MPC5200 CPU) */ #define CONFIG_TQM5200 1 /* ... on a TQM5200 module */ -#define CONFIG_BC3450 1 /* ... on a BC3450 mainboard */ -#define CONFIG_BC3450_PS2 1 /* + a PS/2 converter onboard */ -#define CONFIG_BC3450_IDE 1 /* + IDE drives (Compact Flash) */ +#define CONFIG_BC3450 1 /* ... on a BC3450 mainboard */ +#define CONFIG_BC3450_PS2 1 /* + a PS/2 converter onboard */ +#define CONFIG_BC3450_IDE 1 /* + IDE drives (Compact Flash) */ #define CONFIG_BC3450_USB 1 /* + USB support */ # define CONFIG_FAT 1 /* + FAT support */ # define CONFIG_EXT2 1 /* + EXT2 support */ #undef CONFIG_BC3450_BUZZER /* + Buzzer onboard */ #undef CONFIG_BC3450_CAN /* + CAN transceiver */ #undef CONFIG_BC3450_DS1340 /* + a RTC DS1340 onboard */ -#undef CONFIG_BC3450_DS3231 /* + a RTC DS3231 onboard tbd */ -#undef CONFIG_BC3450_AC97 /* + AC97 on PSC2, tbd */ +#undef CONFIG_BC3450_DS3231 /* + a RTC DS3231 onboard tbd */ +#undef CONFIG_BC3450_AC97 /* + AC97 on PSC2, tbd */ #define CONFIG_BC3450_FP 1 /* + enable FP O/P */ #undef CONFIG_BC3450_CRT /* + enable CRT O/P (Debug only!) */ -#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ +#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ @@ -91,7 +91,7 @@ */ # define CONFIG_PCI 1 # define CONFIG_PCI_PNP 1 -/* #define CONFIG_PCI_SCAN_SHOW 1 */ +/* #define CONFIG_PCI_SCAN_SHOW 1 */ #define CONFIG_PCI_MEM_BUS 0x40000000 #define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS @@ -103,7 +103,7 @@ #define CONFIG_NET_MULTI 1 /*#define CONFIG_EEPRO100 XXX - FIXME: conflicts when CONFIG_MII is enabled */ -#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ +#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ #define CONFIG_NS8382X 1 #ifdef CONFIG_PCI @@ -132,15 +132,15 @@ # define ADD_BMP_CMD 0 #endif -/* - * Partitions +/* + * Partitions */ #define CONFIG_MAC_PARTITION #define CONFIG_DOS_PARTITION #define CONFIG_ISO_PARTITION -/* - * USB +/* + * USB */ #ifdef CONFIG_BC3450_USB # define CONFIG_USB_OHCI @@ -150,8 +150,8 @@ # define ADD_USB_CMD 0 #endif /* CONFIG_BC3450_USB */ -/* - * POST support +/* + * POST support */ #define CONFIG_POST (CFG_POST_MEMORY | \ CFG_POST_CPU | \ @@ -165,8 +165,8 @@ # define CFG_CMD_POST_DIAG 0 #endif /* CONFIG_POST */ -/* - * IDE +/* + * IDE */ #ifdef CONFIG_BC3450_IDE # define ADD_IDE_CMD CFG_CMD_IDE @@ -219,7 +219,7 @@ /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ #include <cmd_confdefs.h> -#define CONFIG_TIMESTAMP /* display image timestamps */ +#define CONFIG_TIMESTAMP /* display image timestamps */ #if (TEXT_BASE == 0xFC000000) /* Boot low */ # define CFG_LOWBOOT 1 @@ -242,14 +242,14 @@ "ipaddr=192.168.1.10\0" \ "serverip=192.168.1.3\0" \ "netmask=255.255.255.0\0" \ - "hostname=bc3450\0" \ + "hostname=bc3450\0" \ "rootpath=/opt/eldk/ppc_6xx\0" \ - "kernel_addr=fc0a0000\0" \ - "ramdisk_addr=fc1c0000\0" \ + "kernel_addr=fc0a0000\0" \ + "ramdisk_addr=fc1c0000\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=$(serverip):$(rootpath)\0" \ - "ideargs=setenv bootargs root=/dev/hda2 ro\0" \ + "ideargs=setenv bootargs root=/dev/hda2 ro\0" \ "addip=setenv bootargs $(bootargs) " \ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \ ":$(hostname):$(netdev):off panic=1\0" \ @@ -260,10 +260,10 @@ "flash_nfs=run nfsargs addip addcons; bootm $(kernel_addr)\0" \ "net_nfs=tftp 200000 $(bootfile); " \ "run nfsargs addip addcons; bootm\0" \ - "ide_nfs=run nfsargs addip addcons; " \ - "disk 200000 0:1; bootm\0" \ - "ide_ide=run ideargs addip addcons; " \ - "disk 200000 0:1; bootm\0" \ + "ide_nfs=run nfsargs addip addcons; " \ + "disk 200000 0:1; bootm\0" \ + "ide_ide=run ideargs addip addcons; " \ + "disk 200000 0:1; bootm\0" \ "usb_self=run usbload; run ramargs addip addcons; " \ "bootm 200000 400000\0" \ "usbload=usb reset; usb scan; usbboot 200000 0:1; " \ @@ -288,7 +288,7 @@ * PCI Bus clocking configuration * * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if - * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet + * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet * hasn't been tested with a IPB Bus Clock of 66 MHz. */ #if defined(CFG_IPBSPEED_133) @@ -314,9 +314,9 @@ #define CFG_I2C_SLAVE 0x7F /* - * EEPROM configuration for I²C EEPROM M24C32 + * EEPROM configuration for I²C EEPROM M24C32 * M24C64 should work also. For other EEPROMs config should be verified. - * + * * The TQM5200 module may hold an EEPROM at address 0x50. */ #define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x (TQM) */ @@ -376,7 +376,7 @@ #define CFG_ENV_SIZE 0x10000 #define CFG_ENV_SECT_SIZE 0x20000 #define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) /* * Memory map @@ -419,25 +419,25 @@ /* * GPIO configuration on BC3450 * - * PSC1: UART1 (Service-UART) [0x xxxxxxx4] - * PSC2: UART2 [0x xxxxxx4x] - * or: AC/97 if CONFIG_BC3450_AC97 [0x xxxxxx2x] - * PSC3: USB2 [0x xxxxx1xx] - * USB: UART4(ext.)/UART5(int.) [0x xxxx2xxx] - * (this has to match - * CONFIG_USB_CONFIG which is - * used by usb_ohci.c to set - * the USB ports) - * Eth: 10/100Mbit Ethernet [0x xxx0xxxx] - * (this is reset to '5' - * in FEC driver: fec.c) - * PSC6: UART6 (int. to PS/2 contr.) [0x xx5xxxxx] - * ATA/CS: ??? [0x x1xxxxxx] - * FIXME! UM Fig 2-10 suggests [0x x0xxxxxx] + * PSC1: UART1 (Service-UART) [0x xxxxxxx4] + * PSC2: UART2 [0x xxxxxx4x] + * or: AC/97 if CONFIG_BC3450_AC97 [0x xxxxxx2x] + * PSC3: USB2 [0x xxxxx1xx] + * USB: UART4(ext.)/UART5(int.) [0x xxxx2xxx] + * (this has to match + * CONFIG_USB_CONFIG which is + * used by usb_ohci.c to set + * the USB ports) + * Eth: 10/100Mbit Ethernet [0x xxx0xxxx] + * (this is reset to '5' + * in FEC driver: fec.c) + * PSC6: UART6 (int. to PS/2 contr.) [0x xx5xxxxx] + * ATA/CS: ??? [0x x1xxxxxx] + * FIXME! UM Fig 2-10 suggests [0x x0xxxxxx] * CS1: Use Pin gpio_wkup_6 as second - * SDRAM chip select (mem_cs1) + * SDRAM chip select (mem_cs1) * Timer: CAN2 / SPI - * I2C: CAN1 / I²C2 [0x bxxxxxxx] + * I2C: CAN1 / I²C2 [0x bxxxxxxx] */ #ifdef CONFIG_BC3450_AC97 # define CFG_GPS_PORT_CONFIG 0xb1502124 @@ -465,7 +465,7 @@ #define CFG_MEMTEST_START 0x00100000 /* memtest works on */ #define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ -#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CFG_LOAD_ADDR 0x100000 /* default load address */ #define CFG_HZ 1000 /* dec freq: 1ms ticks */ @@ -489,7 +489,7 @@ #define CFG_BOOTCS_START CFG_FLASH_BASE #define CFG_BOOTCS_SIZE CFG_FLASH_SIZE #ifdef CFG_PCISPEED_66 -# define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */ +# define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */ #else # define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */ #endif @@ -533,17 +533,17 @@ * USB stuff */ #define CONFIG_USB_CLOCK 0x0001BBBB -#define CONFIG_USB_CONFIG 0x00002000 /* we're using Port 2 */ +#define CONFIG_USB_CONFIG 0x00002000 /* we're using Port 2 */ /* * IDE/ATA stuff Supports IDE harddisk */ #undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ +#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ +#undef CONFIG_IDE_LED /* LED for ide not supported */ -#define CONFIG_IDE_RESET /* reset for ide supported */ +#define CONFIG_IDE_RESET /* reset for ide supported */ #define CONFIG_IDE_PREINIT #define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */ |