diff options
Diffstat (limited to 'include/configs/ASH405.h')
| -rw-r--r-- | include/configs/ASH405.h | 224 |
1 files changed, 112 insertions, 112 deletions
diff --git a/include/configs/ASH405.h b/include/configs/ASH405.h index 3868997..7ed01d1 100644 --- a/include/configs/ASH405.h +++ b/include/configs/ASH405.h @@ -34,13 +34,13 @@ */ #define CONFIG_405EP 1 /* This is a PPC405 CPU */ -#define CONFIG_4xx 1 /* ...member of PPC4xx family */ -#define CONFIG_ASH405 1 /* ...on a ASH405 board */ +#define CONFIG_4xx 1 /* ...member of PPC4xx family */ +#define CONFIG_ASH405 1 /* ...on a ASH405 board */ -#define CONFIG_BOARD_PRE_INIT 1 /* call board_pre_init() */ -#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ +#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ +#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ -#define CONFIG_SYS_CLK_FREQ 33333334 /* external frequency to pll */ +#define CONFIG_SYS_CLK_FREQ 33333334 /* external frequency to pll */ #define CONFIG_BAUDRATE 9600 #define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ @@ -60,7 +60,7 @@ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 0 /* PHY address */ +#define CONFIG_PHY_ADDR 0 /* PHY address */ #define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \ CFG_CMD_DHCP | \ @@ -71,17 +71,17 @@ CFG_CMD_I2C | \ CFG_CMD_MII | \ CFG_CMD_PING | \ - CFG_CMD_EEPROM ) + CFG_CMD_EEPROM ) /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ #include <cmd_confdefs.h> -#undef CONFIG_WATCHDOG /* watchdog disabled */ +#undef CONFIG_WATCHDOG /* watchdog disabled */ -#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/ -#define CFG_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */ +#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/ +#define CFG_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */ -#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ +#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ /* * Miscellaneous configurable options @@ -91,45 +91,45 @@ #undef CFG_HUSH_PARSER /* use "hush" command parser */ #ifdef CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " +#define CFG_PROMPT_HUSH_PS2 "> " #endif #if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ #define CFG_MAXARGS 16 /* max number of command args */ #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */ +#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */ -#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ +#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ #define CFG_MEMTEST_START 0x0400000 /* memtest works on */ #define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ -#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */ -#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */ -#define CFG_BASE_BAUD 691200 -#undef CONFIG_UART1_CONSOLE /* define for uart1 as console */ +#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */ +#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */ +#define CFG_BASE_BAUD 691200 +#undef CONFIG_UART1_CONSOLE /* define for uart1 as console */ /* The following table includes the supported baudrates */ -#define CFG_BAUDRATE_TABLE \ +#define CFG_BAUDRATE_TABLE \ { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ 57600, 115200, 230400, 460800, 921600 } #define CFG_LOAD_ADDR 0x100000 /* default load address */ #define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ +#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ -#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */ +#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */ /*----------------------------------------------------------------------- * NAND-FLASH stuff @@ -142,14 +142,14 @@ #define ADDR_PAGE 2 #define ADDR_COLUMN_PAGE 3 -#define NAND_ChipID_UNKNOWN 0x00 +#define NAND_ChipID_UNKNOWN 0x00 #define NAND_MAX_FLOORS 1 #define NAND_MAX_CHIPS 1 -#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */ -#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */ -#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */ -#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */ +#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */ +#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */ +#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */ +#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */ #define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0) #define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0) @@ -168,26 +168,26 @@ * PCI stuff *----------------------------------------------------------------------- */ -#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ -#define PCI_HOST_FORCE 1 /* configure as pci host */ -#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ - -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_HOST PCI_HOST_HOST /* select pci host function */ -#undef CONFIG_PCI_PNP /* do pci plug-and-play */ - /* resource configuration */ - -#undef CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ - -#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ -#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */ -#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/ -#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */ -#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */ -#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ -#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ +#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ +#define PCI_HOST_FORCE 1 /* configure as pci host */ +#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ + +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_HOST PCI_HOST_HOST /* select pci host function */ +#undef CONFIG_PCI_PNP /* do pci plug-and-play */ + /* resource configuration */ + +#undef CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ + +#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ +#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */ +#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/ +#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */ +#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */ +#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ +#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */ +#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ +#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ /*----------------------------------------------------------------------- * Start addresses for the final memory configuration @@ -215,34 +215,34 @@ #define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ #define CFG_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */ -#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */ -#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */ -#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */ +#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */ +#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */ +#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */ /* * The following defines are added for buggy IOP480 byte interface. * All other boards should use the standard values (CPCI405 etc.) */ -#define CFG_FLASH_READ0 0x0000 /* 0 is standard */ -#define CFG_FLASH_READ1 0x0001 /* 1 is standard */ -#define CFG_FLASH_READ2 0x0002 /* 2 is standard */ +#define CFG_FLASH_READ0 0x0000 /* 0 is standard */ +#define CFG_FLASH_READ1 0x0001 /* 1 is standard */ +#define CFG_FLASH_READ2 0x0002 /* 2 is standard */ -#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ #if 0 /* test-only */ -#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */ -#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */ +#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */ +#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */ #endif /*----------------------------------------------------------------------- * Environment Variable setup */ -#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ -#define CFG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */ -#define CFG_ENV_SIZE 0x700 /* 2048 bytes may be used for env vars*/ +#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ +#define CFG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */ +#define CFG_ENV_SIZE 0x700 /* 2048 bytes may be used for env vars*/ /* total size of a CAT24WC16 is 2048 bytes */ #define CFG_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */ -#define CFG_NVRAM_SIZE 242 /* NVRAM size */ +#define CFG_NVRAM_SIZE 242 /* NVRAM size */ /*----------------------------------------------------------------------- * I2C EEPROM (CAT24WC16) for environment @@ -252,20 +252,20 @@ #define CFG_I2C_SLAVE 0x7F #define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ -#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ -/* mask of address bits that overflow into the "EEPROM chip address" */ +#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ +/* mask of address bits that overflow into the "EEPROM chip address" */ #define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07 #define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */ /* 16 byte page write mode using*/ - /* last 4 bits of the address */ + /* last 4 bits of the address */ #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ #define CFG_EEPROM_PAGE_WRITE_ENABLE /*----------------------------------------------------------------------- * Cache Configuration */ -#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */ - /* have only 8kB, 16kB is save here */ +#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */ + /* have only 8kB, 16kB is save here */ #define CFG_CACHELINE_SIZE 32 /* ... */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ @@ -283,49 +283,49 @@ * External Bus Controller (EBC) Setup */ -/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */ -#define CFG_EBC_PB0AP 0x92015480 -/*#define CFG_EBC_PB0AP 0x08055880 /XXX* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */ -#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */ +/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */ +#define CFG_EBC_PB0AP 0x92015480 +/*#define CFG_EBC_PB0AP 0x08055880 /XXX* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */ +#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */ -/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */ -#define CFG_EBC_PB1AP 0x92015480 -#define CFG_EBC_PB1CR 0xF4018000 /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit */ +/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */ +#define CFG_EBC_PB1AP 0x92015480 +#define CFG_EBC_PB1CR 0xF4018000 /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit */ -/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization */ -#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ -#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */ +/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization */ +#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ +#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */ -/* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization */ -#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ -#define CFG_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */ +/* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization */ +#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ +#define CFG_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */ -#define CAN_BA 0xF0000000 /* CAN Base Address */ -#define DUART0_BA 0xF0000400 /* DUART Base Address */ -#define DUART1_BA 0xF0000408 /* DUART Base Address */ -#define DUART2_BA 0xF0000410 /* DUART Base Address */ -#define DUART3_BA 0xF0000418 /* DUART Base Address */ -#define RTC_BA 0xF0000500 /* RTC Base Address */ -#define CFG_NAND_BASE 0xF4000000 +#define CAN_BA 0xF0000000 /* CAN Base Address */ +#define DUART0_BA 0xF0000400 /* DUART Base Address */ +#define DUART1_BA 0xF0000408 /* DUART Base Address */ +#define DUART2_BA 0xF0000410 /* DUART Base Address */ +#define DUART3_BA 0xF0000418 /* DUART Base Address */ +#define RTC_BA 0xF0000500 /* RTC Base Address */ +#define CFG_NAND_BASE 0xF4000000 /*----------------------------------------------------------------------- * FPGA stuff */ -#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */ -#define CFG_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/ +#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */ +#define CFG_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/ /* FPGA program pin configuration */ -#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */ -#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */ -#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */ -#define CFG_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */ -#define CFG_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */ +#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */ +#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */ +#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */ +#define CFG_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */ +#define CFG_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */ /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in data cache) */ /* use on chip memory ( OCM ) for temperary stack until sdram is tested */ -#define CFG_TEMP_STACK_OCM 1 +#define CFG_TEMP_STACK_OCM 1 /* On Chip Memory location */ #define CFG_OCM_DATA_ADDR 0xF8000000 @@ -335,13 +335,13 @@ #define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET /*----------------------------------------------------------------------- * Definitions for GPIO setup (PPC405EP specific) * - * GPIO0[0] - External Bus Controller BLAST output - * GPIO0[1-9] - Instruction trace outputs -> GPIO + * GPIO0[0] - External Bus Controller BLAST output + * GPIO0[1-9] - Instruction trace outputs -> GPIO * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs @@ -349,15 +349,15 @@ * GPIO0[28-29] - UART1 data signal input/output * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs */ -#define CFG_GPIO0_OSRH 0x40000550 -#define CFG_GPIO0_OSRL 0x00000110 -#define CFG_GPIO0_ISR1H 0x00000000 -#define CFG_GPIO0_ISR1L 0x15555445 -#define CFG_GPIO0_TSRH 0x00000000 -#define CFG_GPIO0_TSRL 0x00000000 -#define CFG_GPIO0_TCR 0xF7FE0014 +#define CFG_GPIO0_OSRH 0x40000550 +#define CFG_GPIO0_OSRL 0x00000110 +#define CFG_GPIO0_ISR1H 0x00000000 +#define CFG_GPIO0_ISR1L 0x15555445 +#define CFG_GPIO0_TSRH 0x00000000 +#define CFG_GPIO0_TSRL 0x00000000 +#define CFG_GPIO0_TCR 0xF7FE0014 -#define CFG_DUART_RST (0x80000000 >> 14) +#define CFG_DUART_RST (0x80000000 >> 14) /* * Internal Definitions @@ -372,16 +372,16 @@ * This value will be set if iic boot eprom is disabled. */ #if 0 -#define PLLMR0_DEFAULT PLLMR0_266_133_66_33 -#define PLLMR1_DEFAULT PLLMR1_266_133_66_33 +#define PLLMR0_DEFAULT PLLMR0_266_133_66_33 +#define PLLMR1_DEFAULT PLLMR1_266_133_66_33 #endif #if 1 -#define PLLMR0_DEFAULT PLLMR0_200_100_50_33 -#define PLLMR1_DEFAULT PLLMR1_200_100_50_33 +#define PLLMR0_DEFAULT PLLMR0_200_100_50_33 +#define PLLMR1_DEFAULT PLLMR1_200_100_50_33 #endif #if 0 -#define PLLMR0_DEFAULT PLLMR0_133_66_66_33 -#define PLLMR1_DEFAULT PLLMR1_133_66_66_33 +#define PLLMR0_DEFAULT PLLMR0_133_66_66_33 +#define PLLMR1_DEFAULT PLLMR1_133_66_66_33 #endif #endif /* __CONFIG_H */ |