diff options
Diffstat (limited to 'include/configs/APC405.h')
| -rw-r--r-- | include/configs/APC405.h | 424 |
1 files changed, 0 insertions, 424 deletions
diff --git a/include/configs/APC405.h b/include/configs/APC405.h deleted file mode 100644 index 2678f50..0000000 --- a/include/configs/APC405.h +++ /dev/null @@ -1,424 +0,0 @@ -/* - * (C) Copyright 2005-2008 - * Matthias Fuchs, esd gmbh germany, matthias.fuchs@esd-electronics.com - * - * (C) Copyright 2001-2004 - * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ -#define CONFIG_405GP 1 /* This is a PPC405 CPU */ -#define CONFIG_APCG405 1 /* ...on a APC405 board */ - -#define CONFIG_SYS_TEXT_BASE 0xFFF80000 - -#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ -#define CONFIG_BOARD_EARLY_INIT_R 1 -#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ - -#define CONFIG_SYS_CLK_FREQ 33333400 /* external frequency to pll */ - -#define CONFIG_BOARD_TYPES 1 /* support board types */ - -#define CONFIG_BAUDRATE 115200 -#define CONFIG_BOOTDELAY 1 /* autoboot after 3 seconds */ -#define CONFIG_BOOTCOUNT_LIMIT 1 - -#undef CONFIG_BOOTARGS - -#define CONFIG_SYS_USB_LOAD_COMMAND "fatload usb 0 200000 pImage;" \ - "fatload usb 0 300000 pImage.initrd" -#define CONFIG_SYS_USB_SELF_COMMAND "usb start;run usb_load;usb stop;" \ - "run ramargs addip addcon usbargs;" \ - "bootm 200000 300000" -#define CONFIG_SYS_USB_ARGS "setenv bootargs $(bootargs) usbboot=1" -#define CONFIG_SYS_BOOTLIMIT "3" -#define CONFIG_SYS_ALT_BOOTCOMMAND "run usb_self;reset" - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "hostname=abg405\0" \ - "bd_type=abg405\0" \ - "serial#=AA0000\0" \ - "kernel_addr=fe000000\0" \ - "ramdisk_addr=fe100000\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$(serverip):$(rootpath)\0" \ - "addip=setenv bootargs $(bootargs) " \ - "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \ - ":$(hostname)::off panic=1\0" \ - "addcon=setenv bootargs $(bootargs) console=ttyS0,$(baudrate)" \ - " $(optargs)\0" \ - "flash_self=run ramargs addip addcon;" \ - "bootm $(kernel_addr) $(ramdisk_addr)\0" \ - "net_nfs=tftp 200000 $(img);run nfsargs addip addcon;" \ - "bootm\0" \ - "rootpath=/tftpboot/abg405/target_root\0" \ - "img=/tftpboot/abg405/pImage\0" \ - "load=tftp 100000 /tftpboot/abg405/u-boot.bin\0" \ - "update=protect off fff80000 ffffffff;era fff80000 ffffffff;" \ - "cp.b 100000 fff80000 80000\0" \ - "ipaddr=10.0.111.111\0" \ - "netmask=255.255.0.0\0" \ - "serverip=10.0.0.190\0" \ - "splashimage=ffe80000\0" \ - "usb_load="CONFIG_SYS_USB_LOAD_COMMAND"\0" \ - "usb_self="CONFIG_SYS_USB_SELF_COMMAND"\0" \ - "usbargs="CONFIG_SYS_USB_ARGS"\0" \ - "bootlimit="CONFIG_SYS_BOOTLIMIT"\0" \ - "altbootcmd="CONFIG_SYS_ALT_BOOTCOMMAND"\0" \ - "" -#define CONFIG_BOOTCOMMAND "run flash_self;reset" - -#define CONFIG_ETHADDR 00:02:27:8e:00:00 - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#undef CONFIG_HAS_ETH1 - -#define CONFIG_PPC4xx_EMAC -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 0 /* PHY address */ -#define CONFIG_LXT971_NO_SLEEP 1 -#define CONFIG_RESET_PHY_R 1 /* use reset_phy() */ - -#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IDE -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_SOURCE -#define CONFIG_CMD_USB - -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION - -#define CONFIG_SUPPORT_VFAT - -#define CONFIG_AUTO_UPDATE 1 /* autoupdate via CF or USB */ - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/ -#define CONFIG_SYS_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */ - -#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */ - -#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CONFIG_CONS_INDEX 1 /* Use UART0 */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_serial_clock() - -#define CONFIG_SYS_EXT_SERIAL_CLOCK 14745600 /* use external serial clock */ - -/* The following table includes the supported baudrates */ -#define CONFIG_SYS_BAUDRATE_TABLE \ - { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ - 57600, 115200, 230400, 460800, 921600 } - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ - -/* Only interrupt boot if space is pressed */ -/* If a long serial cable is connected but */ -/* other end is dead, garbage will be read */ -#define CONFIG_AUTOBOOT_KEYED 1 -#define CONFIG_AUTOBOOT_PROMPT \ - "Press SPACE to abort autoboot in %d seconds\n", bootdelay -#undef CONFIG_AUTOBOOT_DELAY_STR -#define CONFIG_AUTOBOOT_STOP_STR " " - -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - -#define CONFIG_SYS_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */ - -/* - * PCI stuff - */ -#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ -#define PCI_HOST_FORCE 1 /* configure as pci host */ -#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ - -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ -#define CONFIG_PCI_PNP /* do pci plug-and-play */ - /* resource configuration */ - -#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ -#define CONFIG_PCI_SKIP_HOST_BRIDGE 1 -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ -#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */ -#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/ -#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CONFIG_SYS_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */ -#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */ -#define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ -#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ - -/* - * IDE/ATA stuff - */ -#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ -#undef CONFIG_IDE_LED /* no led for ide supported */ -#define CONFIG_IDE_RESET 1 /* reset for ide supported */ - -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */ -#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS) /* max. 1 drives per IDE bus */ - -#define CONFIG_SYS_ATA_BASE_ADDR 0xF0100000 -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 - -#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ -#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register access */ -#define CONFIG_SYS_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */ - -/* - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_MONITOR_BASE 0xFFF80000 -#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (2*1024*1024) /* Reserve 2MB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Init. Memory map for Linux */ - -/* - * FLASH organization - */ -#define CONFIG_SYS_FLASH_BASE 0xFE000000 -#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max num of sects on one chip */ -#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 2 -#define CONFIG_SYS_FLASH_QUIET_TEST 1 -#define CONFIG_SYS_FLASH_INCREMENT 0x01000000 -#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware protection */ -#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { \ - {0xfe000000, 0x500000}, \ - {0xffe80000, 0x180000} \ - } -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -#define CONFIG_SYS_FLASH_BANKS_LIST { \ - CONFIG_SYS_FLASH_BASE, \ - CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_INCREMENT \ - } -#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ - -/* - * Environment Variable setup - */ -#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ -#define CONFIG_ENV_OFFSET 0x000 /* environment starts at the */ - /* beginning of the EEPROM */ -#define CONFIG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars*/ -#define CONFIG_ENV_OVERWRITE 1 /* allow overwriting vendor vars */ - -#define CONFIG_SYS_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */ -#define CONFIG_SYS_NVRAM_SIZE 242 /* NVRAM size */ - -/* - * I2C EEPROM (CAT24WC16) for environment - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_PPC4XX -#define CONFIG_SYS_I2C_PPC4XX_CH0 -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F - -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ -/* mask of address bits that overflow into the "EEPROM chip address" */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */ - /* 16 byte page write mode using*/ - /* last 4 bits of the address */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ - -/* - * External Bus Controller (EBC) Setup - */ -#define FLASH0_BA (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_INCREMENT) /* FLASH 0 BA */ -#define FLASH1_BA CONFIG_SYS_FLASH_BASE /* FLASH 1 Base Address */ -#define CAN_BA 0xF0000000 /* CAN Base Address */ -#define DUART0_BA 0xF0000400 /* DUART Base Address */ -#define DUART1_BA 0xF0000408 /* DUART Base Address */ -#define RTC_BA 0xF0000500 /* RTC Base Address */ -#define PS2_BA 0xF0000600 /* PS/2 Base Address */ -#define CF_BA 0xF0100000 /* CompactFlash Base Address */ -#define FPGA_BA 0xF0100100 /* FPGA internal Base Address */ -#define FUJI_BA 0xF0100200 /* Fuji internal Base Address */ -#define PCMCIA1_BA 0x20000000 /* PCMCIA Slot 1 Base Address */ -#define PCMCIA2_BA 0x28000000 /* PCMCIA Slot 2 Base Address */ -#define VGA_BA 0xF1000000 /* Epson VGA Base Address */ - -#define CONFIG_SYS_FPGA_BASE_ADDR FPGA_BA /* FPGA internal Base Address */ - -/* Memory Bank 0 (Flash Bank 0) initialization */ -#define CONFIG_SYS_EBC_PB0AP 0x92015480 -#define CONFIG_SYS_EBC_PB0CR FLASH0_BA | 0x9A000 /* BAS=0xFF0,BS=16MB,BU=R/W,BW=16bit*/ -#define CONFIG_SYS_EBC_PB0AP_HWREV8 CONFIG_SYS_EBC_PB0AP -#define CONFIG_SYS_EBC_PB0CR_HWREV8 FLASH1_BA | 0xBA000 /* BS=32MB */ - -/* Memory Bank 1 (Flash Bank 1) initialization */ -#define CONFIG_SYS_EBC_PB1AP 0x92015480 -#define CONFIG_SYS_EBC_PB1CR FLASH1_BA | 0x9A000 /* BAS=0xFE0,BS=16MB,BU=R/W,BW=16bit*/ - -/* Memory Bank 2 (CAN0, 1, RTC, Duart) initialization */ -#define CONFIG_SYS_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ -#define CONFIG_SYS_EBC_PB2CR CAN_BA | 0x18000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */ - -/* Memory Bank 3 (CompactFlash IDE, FPGA internal) initialization */ -#define CONFIG_SYS_EBC_PB3AP 0x010059C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ -#define CONFIG_SYS_EBC_PB3CR CF_BA | 0x1A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */ - -/* Memory Bank 4 (PCMCIA Slot 1) initialization */ -#define CONFIG_SYS_EBC_PB4AP 0x050007C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ -#define CONFIG_SYS_EBC_PB4CR PCMCIA1_BA | 0xFA000 /*BAS=0x200,BS=128MB,BU=R/W,BW=16bit*/ - -/* Memory Bank 5 (Epson VGA) initialization */ -#define CONFIG_SYS_EBC_PB5AP 0x03805380 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=0 */ -#define CONFIG_SYS_EBC_PB5CR VGA_BA | 0x5A000 /* BAS=0xF10,BS=4MB,BU=R/W,BW=16bit */ - -/* Memory Bank 6 (PCMCIA Slot 2) initialization */ -#define CONFIG_SYS_EBC_PB6AP 0x050007C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ -#define CONFIG_SYS_EBC_PB6CR PCMCIA2_BA | 0xFA000 /*BAS=0x280,BS=128MB,BU=R/W,BW=16bit*/ - -/* - * FPGA stuff - */ - -/* FPGA internal regs */ -#define CONFIG_SYS_FPGA_CTRL 0x008 -#define CONFIG_SYS_FPGA_CTRL2 0x00a - -/* FPGA Control Reg */ -#define CONFIG_SYS_FPGA_CTRL_CF_RESET 0x0001 -#define CONFIG_SYS_FPGA_CTRL_WDI 0x0002 -#define CONFIG_SYS_FPGA_CTRL_PS2_RESET 0x0020 - -#define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */ -#define CONFIG_SYS_FPGA_MAX_SIZE 80*1024 /* 80kByte is enough for XC2S50 */ - -/* FPGA program pin configuration */ -#define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */ -#define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */ -#define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */ -#define CONFIG_SYS_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */ -#define CONFIG_SYS_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */ - -/* - * LCD Setup - */ -#define CONFIG_SYS_LCD_BIG_MEM (VGA_BA + 0x200000) /* S1D13806 Mem Base */ -#define CONFIG_SYS_LCD_BIG_REG VGA_BA /* S1D13806 Reg Base */ - -#define CONFIG_LCD_BIG 2 /* Epson S1D13806 used */ - -/* Image information... */ -#define CONFIG_LCD_USED CONFIG_LCD_BIG - -#define CONFIG_SYS_LCD_MEM CONFIG_SYS_LCD_BIG_MEM -#define CONFIG_SYS_LCD_REG CONFIG_SYS_LCD_BIG_REG - -#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (1 << 20) - -/* - * Definitions for initial stack pointer and data area (in data cache) - */ - -/* use on chip memory ( OCM ) for temperary stack until sdram is tested */ -#define CONFIG_SYS_TEMP_STACK_OCM 1 - -/* On Chip Memory location */ -#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 -#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 - -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */ -#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -/* reserve some memory for BOOT limit info */ -#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 16) - -#ifdef CONFIG_BOOTCOUNT_LIMIT /* reserve 2 word for bootcount limit */ -#define CONFIG_SYS_BOOTCOUNT_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 8) -#endif - -/* - * PCI OHCI controller - */ -#define CONFIG_USB_OHCI_NEW 1 -#define CONFIG_PCI_OHCI 1 -#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1 -#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 -#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci" -#define CONFIG_USB_STORAGE 1 -#define CONFIG_SYS_USB_OHCI_BOARD_INIT 1 - -#endif /* __CONFIG_H */ |