diff options
Diffstat (limited to 'drivers')
-rw-r--r-- | drivers/mmc/sunxi_mmc.c | 27 | ||||
-rw-r--r-- | drivers/mtd/spi/Kconfig | 12 | ||||
-rw-r--r-- | drivers/mtd/spi/Makefile | 1 | ||||
-rw-r--r-- | drivers/mtd/spi/sunxi_spi_spl.c | 283 | ||||
-rw-r--r-- | drivers/net/Kconfig | 9 | ||||
-rw-r--r-- | drivers/net/Makefile | 1 | ||||
-rw-r--r-- | drivers/net/sun8i_emac.c | 789 |
7 files changed, 1100 insertions, 22 deletions
diff --git a/drivers/mmc/sunxi_mmc.c b/drivers/mmc/sunxi_mmc.c index ce2dc4a..5d8abdc 100644 --- a/drivers/mmc/sunxi_mmc.c +++ b/drivers/mmc/sunxi_mmc.c @@ -269,18 +269,18 @@ static int mmc_trans_data_by_cpu(struct mmc *mmc, struct mmc_data *data) unsigned i; unsigned *buff = (unsigned int *)(reading ? data->dest : data->src); unsigned byte_cnt = data->blocksize * data->blocks; - unsigned timeout_msecs = byte_cnt >> 8; - if (timeout_msecs < 2000) - timeout_msecs = 2000; + unsigned timeout_usecs = (byte_cnt >> 8) * 1000; + if (timeout_usecs < 2000000) + timeout_usecs = 2000000; /* Always read / write data through the CPU */ setbits_le32(&mmchost->reg->gctrl, SUNXI_MMC_GCTRL_ACCESS_BY_AHB); for (i = 0; i < (byte_cnt >> 2); i++) { while (readl(&mmchost->reg->status) & status_bit) { - if (!timeout_msecs--) + if (!timeout_usecs--) return -1; - udelay(1000); + udelay(1); } if (reading) @@ -445,23 +445,6 @@ static int sunxi_mmc_getcd(struct mmc *mmc) return !gpio_get_value(cd_pin); } -int sunxi_mmc_has_egon_boot_signature(struct mmc *mmc) -{ - char *buf = malloc(512); - int valid_signature = 0; - - if (buf == NULL) - panic("Failed to allocate memory\n"); - - if (mmc_getcd(mmc) && mmc_init(mmc) == 0 && - mmc->block_dev.block_read(&mmc->block_dev, 16, 1, buf) == 1 && - strncmp(&buf[4], "eGON.BT0", 8) == 0) - valid_signature = 1; - - free(buf); - return valid_signature; -} - static const struct mmc_ops sunxi_mmc_ops = { .send_cmd = sunxi_mmc_send_cmd, .set_ios = sunxi_mmc_set_ios, diff --git a/drivers/mtd/spi/Kconfig b/drivers/mtd/spi/Kconfig index 3f7433c..1f23c8e 100644 --- a/drivers/mtd/spi/Kconfig +++ b/drivers/mtd/spi/Kconfig @@ -128,4 +128,16 @@ config SPI_FLASH_MTD If unsure, say N +if SPL + +config SPL_SPI_SUNXI + bool "Support for SPI Flash on Allwinner SoCs in SPL" + depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUN8I_H3 || MACH_SUN50I + ---help--- + Enable support for SPI Flash. This option allows SPL to read from + sunxi SPI Flash. It uses the same method as the boot ROM, so does + not need any extra configuration. + +endif + endmenu # menu "SPI Flash Support" diff --git a/drivers/mtd/spi/Makefile b/drivers/mtd/spi/Makefile index c665836..6f47a66 100644 --- a/drivers/mtd/spi/Makefile +++ b/drivers/mtd/spi/Makefile @@ -10,6 +10,7 @@ obj-$(CONFIG_DM_SPI_FLASH) += sf-uclass.o ifdef CONFIG_SPL_BUILD obj-$(CONFIG_SPL_SPI_LOAD) += spi_spl_load.o obj-$(CONFIG_SPL_SPI_BOOT) += fsl_espi_spl.o +obj-$(CONFIG_SPL_SPI_SUNXI) += sunxi_spi_spl.o endif obj-$(CONFIG_SPI_FLASH) += sf_probe.o spi_flash.o sf_params.o sf.o diff --git a/drivers/mtd/spi/sunxi_spi_spl.c b/drivers/mtd/spi/sunxi_spi_spl.c new file mode 100644 index 0000000..e3ded5b --- /dev/null +++ b/drivers/mtd/spi/sunxi_spi_spl.c @@ -0,0 +1,283 @@ +/* + * Copyright (C) 2016 Siarhei Siamashka <siarhei.siamashka@gmail.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <spl.h> +#include <asm/gpio.h> +#include <asm/io.h> + +#ifdef CONFIG_SPL_OS_BOOT +#error CONFIG_SPL_OS_BOOT is not supported yet +#endif + +/* + * This is a very simple U-Boot image loading implementation, trying to + * replicate what the boot ROM is doing when loading the SPL. Because we + * know the exact pins where the SPI Flash is connected and also know + * that the Read Data Bytes (03h) command is supported, the hardware + * configuration is very simple and we don't need the extra flexibility + * of the SPI framework. Moreover, we rely on the default settings of + * the SPI controler hardware registers and only adjust what needs to + * be changed. This is good for the code size and this implementation + * adds less than 400 bytes to the SPL. + * + * There are two variants of the SPI controller in Allwinner SoCs: + * A10/A13/A20 (sun4i variant) and everything else (sun6i variant). + * Both of them are supported. + * + * The pin mixing part is SoC specific and only A10/A13/A20/H3/A64 are + * supported at the moment. + */ + +/*****************************************************************************/ +/* SUN4I variant of the SPI controller */ +/*****************************************************************************/ + +#define SUN4I_SPI0_CCTL (0x01C05000 + 0x1C) +#define SUN4I_SPI0_CTL (0x01C05000 + 0x08) +#define SUN4I_SPI0_RX (0x01C05000 + 0x00) +#define SUN4I_SPI0_TX (0x01C05000 + 0x04) +#define SUN4I_SPI0_FIFO_STA (0x01C05000 + 0x28) +#define SUN4I_SPI0_BC (0x01C05000 + 0x20) +#define SUN4I_SPI0_TC (0x01C05000 + 0x24) + +#define SUN4I_CTL_ENABLE BIT(0) +#define SUN4I_CTL_MASTER BIT(1) +#define SUN4I_CTL_TF_RST BIT(8) +#define SUN4I_CTL_RF_RST BIT(9) +#define SUN4I_CTL_XCH BIT(10) + +/*****************************************************************************/ +/* SUN6I variant of the SPI controller */ +/*****************************************************************************/ + +#define SUN6I_SPI0_CCTL (0x01C68000 + 0x24) +#define SUN6I_SPI0_GCR (0x01C68000 + 0x04) +#define SUN6I_SPI0_TCR (0x01C68000 + 0x08) +#define SUN6I_SPI0_FIFO_STA (0x01C68000 + 0x1C) +#define SUN6I_SPI0_MBC (0x01C68000 + 0x30) +#define SUN6I_SPI0_MTC (0x01C68000 + 0x34) +#define SUN6I_SPI0_BCC (0x01C68000 + 0x38) +#define SUN6I_SPI0_TXD (0x01C68000 + 0x200) +#define SUN6I_SPI0_RXD (0x01C68000 + 0x300) + +#define SUN6I_CTL_ENABLE BIT(0) +#define SUN6I_CTL_MASTER BIT(1) +#define SUN6I_CTL_SRST BIT(31) +#define SUN6I_TCR_XCH BIT(31) + +/*****************************************************************************/ + +#define CCM_AHB_GATING0 (0x01C20000 + 0x60) +#define CCM_SPI0_CLK (0x01C20000 + 0xA0) +#define SUN6I_BUS_SOFT_RST_REG0 (0x01C20000 + 0x2C0) + +#define AHB_RESET_SPI0_SHIFT 20 +#define AHB_GATE_OFFSET_SPI0 20 + +#define SPI0_CLK_DIV_BY_2 0x1000 +#define SPI0_CLK_DIV_BY_4 0x1001 + +/*****************************************************************************/ + +/* + * Allwinner A10/A20 SoCs were using pins PC0,PC1,PC2,PC23 for booting + * from SPI Flash, everything else is using pins PC0,PC1,PC2,PC3. + */ +static void spi0_pinmux_setup(unsigned int pin_function) +{ + unsigned int pin; + + for (pin = SUNXI_GPC(0); pin <= SUNXI_GPC(2); pin++) + sunxi_gpio_set_cfgpin(pin, pin_function); + + if (IS_ENABLED(CONFIG_MACH_SUN4I) || IS_ENABLED(CONFIG_MACH_SUN7I)) + sunxi_gpio_set_cfgpin(SUNXI_GPC(23), pin_function); + else + sunxi_gpio_set_cfgpin(SUNXI_GPC(3), pin_function); +} + +/* + * Setup 6 MHz from OSC24M (because the BROM is doing the same). + */ +static void spi0_enable_clock(void) +{ + /* Deassert SPI0 reset on SUN6I */ + if (IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I)) + setbits_le32(SUN6I_BUS_SOFT_RST_REG0, + (1 << AHB_RESET_SPI0_SHIFT)); + + /* Open the SPI0 gate */ + setbits_le32(CCM_AHB_GATING0, (1 << AHB_GATE_OFFSET_SPI0)); + + /* Divide by 4 */ + writel(SPI0_CLK_DIV_BY_4, IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I) ? + SUN6I_SPI0_CCTL : SUN4I_SPI0_CCTL); + /* 24MHz from OSC24M */ + writel((1 << 31), CCM_SPI0_CLK); + + if (IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I)) { + /* Enable SPI in the master mode and do a soft reset */ + setbits_le32(SUN6I_SPI0_GCR, SUN6I_CTL_MASTER | + SUN6I_CTL_ENABLE | + SUN6I_CTL_SRST); + /* Wait for completion */ + while (readl(SUN6I_SPI0_GCR) & SUN6I_CTL_SRST) + ; + } else { + /* Enable SPI in the master mode and reset FIFO */ + setbits_le32(SUN4I_SPI0_CTL, SUN4I_CTL_MASTER | + SUN4I_CTL_ENABLE | + SUN4I_CTL_TF_RST | + SUN4I_CTL_RF_RST); + } +} + +static void spi0_disable_clock(void) +{ + /* Disable the SPI0 controller */ + if (IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I)) + clrbits_le32(SUN6I_SPI0_GCR, SUN6I_CTL_MASTER | + SUN6I_CTL_ENABLE); + else + clrbits_le32(SUN4I_SPI0_CTL, SUN4I_CTL_MASTER | + SUN4I_CTL_ENABLE); + + /* Disable the SPI0 clock */ + writel(0, CCM_SPI0_CLK); + + /* Close the SPI0 gate */ + clrbits_le32(CCM_AHB_GATING0, (1 << AHB_GATE_OFFSET_SPI0)); + + /* Assert SPI0 reset on SUN6I */ + if (IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I)) + clrbits_le32(SUN6I_BUS_SOFT_RST_REG0, + (1 << AHB_RESET_SPI0_SHIFT)); +} + +static int spi0_init(void) +{ + unsigned int pin_function = SUNXI_GPC_SPI0; + if (IS_ENABLED(CONFIG_MACH_SUN50I)) + pin_function = SUN50I_GPC_SPI0; + + spi0_pinmux_setup(pin_function); + spi0_enable_clock(); +} + +static void spi0_deinit(void) +{ + /* New SoCs can disable pins, older could only set them as input */ + unsigned int pin_function = SUNXI_GPIO_INPUT; + if (IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I)) + pin_function = SUNXI_GPIO_DISABLE; + + spi0_disable_clock(); + spi0_pinmux_setup(pin_function); +} + +/*****************************************************************************/ + +#define SPI_READ_MAX_SIZE 60 /* FIFO size, minus 4 bytes of the header */ + +static void sunxi_spi0_read_data(u8 *buf, u32 addr, u32 bufsize, + u32 spi_ctl_reg, + u32 spi_ctl_xch_bitmask, + u32 spi_fifo_reg, + u32 spi_tx_reg, + u32 spi_rx_reg, + u32 spi_bc_reg, + u32 spi_tc_reg, + u32 spi_bcc_reg) +{ + writel(4 + bufsize, spi_bc_reg); /* Burst counter (total bytes) */ + writel(4, spi_tc_reg); /* Transfer counter (bytes to send) */ + if (spi_bcc_reg) + writel(4, spi_bcc_reg); /* SUN6I also needs this */ + + /* Send the Read Data Bytes (03h) command header */ + writeb(0x03, spi_tx_reg); + writeb((u8)(addr >> 16), spi_tx_reg); + writeb((u8)(addr >> 8), spi_tx_reg); + writeb((u8)(addr), spi_tx_reg); + + /* Start the data transfer */ + setbits_le32(spi_ctl_reg, spi_ctl_xch_bitmask); + + /* Wait until everything is received in the RX FIFO */ + while ((readl(spi_fifo_reg) & 0x7F) < 4 + bufsize) + ; + + /* Skip 4 bytes */ + readl(spi_rx_reg); + + /* Read the data */ + while (bufsize-- > 0) + *buf++ = readb(spi_rx_reg); + + /* tSHSL time is up to 100 ns in various SPI flash datasheets */ + udelay(1); +} + +static void spi0_read_data(void *buf, u32 addr, u32 len) +{ + u8 *buf8 = buf; + u32 chunk_len; + + while (len > 0) { + chunk_len = len; + if (chunk_len > SPI_READ_MAX_SIZE) + chunk_len = SPI_READ_MAX_SIZE; + + if (IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I)) { + sunxi_spi0_read_data(buf8, addr, chunk_len, + SUN6I_SPI0_TCR, + SUN6I_TCR_XCH, + SUN6I_SPI0_FIFO_STA, + SUN6I_SPI0_TXD, + SUN6I_SPI0_RXD, + SUN6I_SPI0_MBC, + SUN6I_SPI0_MTC, + SUN6I_SPI0_BCC); + } else { + sunxi_spi0_read_data(buf8, addr, chunk_len, + SUN4I_SPI0_CTL, + SUN4I_CTL_XCH, + SUN4I_SPI0_FIFO_STA, + SUN4I_SPI0_TX, + SUN4I_SPI0_RX, + SUN4I_SPI0_BC, + SUN4I_SPI0_TC, + 0); + } + + len -= chunk_len; + buf8 += chunk_len; + addr += chunk_len; + } +} + +/*****************************************************************************/ + +int spl_spi_load_image(void) +{ + int err; + struct image_header *header; + header = (struct image_header *)(CONFIG_SYS_TEXT_BASE); + + spi0_init(); + + spi0_read_data((void *)header, CONFIG_SYS_SPI_U_BOOT_OFFS, 0x40); + err = spl_parse_image_header(header); + if (err) + return err; + + spi0_read_data((void *)spl_image.load_addr, CONFIG_SYS_SPI_U_BOOT_OFFS, + spl_image.size); + + spi0_deinit(); + return 0; +} diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index c1cb689..88d8e83 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -152,6 +152,15 @@ config RTL8169 This driver supports Realtek 8169 series gigabit ethernet family of PCI/PCIe chipsets/adapters. +config SUN8I_EMAC + bool "Allwinner Sun8i Ethernet MAC support" + depends on DM_ETH + select PHYLIB + help + This driver supports the Allwinner based SUN8I/SUN50I Ethernet MAC. + It can be found in H3/A64/A83T based SoCs and compatible with both + External and Internal PHY's. + config XILINX_AXIEMAC depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP) select PHYLIB diff --git a/drivers/net/Makefile b/drivers/net/Makefile index 5702592..a448526 100644 --- a/drivers/net/Makefile +++ b/drivers/net/Makefile @@ -24,6 +24,7 @@ obj-$(CONFIG_E1000) += e1000.o obj-$(CONFIG_E1000_SPI) += e1000_spi.o obj-$(CONFIG_EEPRO100) += eepro100.o obj-$(CONFIG_SUNXI_EMAC) += sunxi_emac.o +obj-$(CONFIG_SUN8I_EMAC) += sun8i_emac.o obj-$(CONFIG_ENC28J60) += enc28j60.o obj-$(CONFIG_EP93XX) += ep93xx_eth.o obj-$(CONFIG_ETHOC) += ethoc.o diff --git a/drivers/net/sun8i_emac.c b/drivers/net/sun8i_emac.c new file mode 100644 index 0000000..4bed50d --- /dev/null +++ b/drivers/net/sun8i_emac.c @@ -0,0 +1,789 @@ +/* + * (C) Copyright 2016 + * Author: Amit Singh Tomar, amittomer25@gmail.com + * + * SPDX-License-Identifier: GPL-2.0+ + * + * Ethernet driver for H3/A64/A83T based SoC's + * + * It is derived from the work done by + * LABBE Corentin & Chen-Yu Tsai for Linux, THANKS! + * +*/ + +#include <asm/io.h> +#include <asm/arch/clock.h> +#include <asm/arch/gpio.h> +#include <common.h> +#include <dm.h> +#include <fdt_support.h> +#include <linux/err.h> +#include <malloc.h> +#include <miiphy.h> +#include <net.h> + +#define SCTL_EMAC_TX_CLK_SRC_MII BIT(0) +#define SCTL_EMAC_EPIT_MII BIT(2) +#define SCTL_EMAC_CLK_SEL BIT(18) /* 25 Mhz */ + +#define MDIO_CMD_MII_BUSY BIT(0) +#define MDIO_CMD_MII_WRITE BIT(1) + +#define MDIO_CMD_MII_PHY_REG_ADDR_MASK 0x000001f0 +#define MDIO_CMD_MII_PHY_REG_ADDR_SHIFT 4 +#define MDIO_CMD_MII_PHY_ADDR_MASK 0x0001f000 +#define MDIO_CMD_MII_PHY_ADDR_SHIFT 12 + +#define CONFIG_TX_DESCR_NUM 32 +#define CONFIG_RX_DESCR_NUM 32 +#define CONFIG_ETH_BUFSIZE 2024 + +#define TX_TOTAL_BUFSIZE (CONFIG_ETH_BUFSIZE * CONFIG_TX_DESCR_NUM) +#define RX_TOTAL_BUFSIZE (CONFIG_ETH_BUFSIZE * CONFIG_RX_DESCR_NUM) + +#define H3_EPHY_DEFAULT_VALUE 0x58000 +#define H3_EPHY_DEFAULT_MASK GENMASK(31, 15) +#define H3_EPHY_ADDR_SHIFT 20 +#define REG_PHY_ADDR_MASK GENMASK(4, 0) +#define H3_EPHY_LED_POL BIT(17) /* 1: active low, 0: active high */ +#define H3_EPHY_SHUTDOWN BIT(16) /* 1: shutdown, 0: power up */ +#define H3_EPHY_SELECT BIT(15) /* 1: internal PHY, 0: external PHY */ + +#define SC_RMII_EN BIT(13) +#define SC_EPIT BIT(2) /* 1: RGMII, 0: MII */ +#define SC_ETCS_MASK GENMASK(1, 0) +#define SC_ETCS_EXT_GMII 0x1 +#define SC_ETCS_INT_GMII 0x2 + +#define CONFIG_MDIO_TIMEOUT (3 * CONFIG_SYS_HZ) + +#define AHB_GATE_OFFSET_EPHY 0 + +#if defined(CONFIG_MACH_SUN8I_H3) +#define SUN8I_GPD8_GMAC 2 +#else +#define SUN8I_GPD8_GMAC 4 +#endif + +/* H3/A64 EMAC Register's offset */ +#define EMAC_CTL0 0x00 +#define EMAC_CTL1 0x04 +#define EMAC_INT_STA 0x08 +#define EMAC_INT_EN 0x0c +#define EMAC_TX_CTL0 0x10 +#define EMAC_TX_CTL1 0x14 +#define EMAC_TX_FLOW_CTL 0x1c +#define EMAC_TX_DMA_DESC 0x20 +#define EMAC_RX_CTL0 0x24 +#define EMAC_RX_CTL1 0x28 +#define EMAC_RX_DMA_DESC 0x34 +#define EMAC_MII_CMD 0x48 +#define EMAC_MII_DATA 0x4c +#define EMAC_ADDR0_HIGH 0x50 +#define EMAC_ADDR0_LOW 0x54 +#define EMAC_TX_DMA_STA 0xb0 +#define EMAC_TX_CUR_DESC 0xb4 +#define EMAC_TX_CUR_BUF 0xb8 +#define EMAC_RX_DMA_STA 0xc0 +#define EMAC_RX_CUR_DESC 0xc4 + +DECLARE_GLOBAL_DATA_PTR; + +enum emac_variant { + A83T_EMAC = 1, + H3_EMAC, + A64_EMAC, +}; + +struct emac_dma_desc { + u32 status; + u32 st; + u32 buf_addr; + u32 next; +} __aligned(ARCH_DMA_MINALIGN); + +struct emac_eth_dev { + struct emac_dma_desc rx_chain[CONFIG_TX_DESCR_NUM]; + struct emac_dma_desc tx_chain[CONFIG_RX_DESCR_NUM]; + char rxbuffer[RX_TOTAL_BUFSIZE] __aligned(ARCH_DMA_MINALIGN); + char txbuffer[TX_TOTAL_BUFSIZE] __aligned(ARCH_DMA_MINALIGN); + + u32 interface; + u32 phyaddr; + u32 link; + u32 speed; + u32 duplex; + u32 phy_configured; + u32 tx_currdescnum; + u32 rx_currdescnum; + u32 addr; + u32 tx_slot; + bool use_internal_phy; + + enum emac_variant variant; + void *mac_reg; + phys_addr_t sysctl_reg; + struct phy_device *phydev; + struct mii_dev *bus; +}; + +static int sun8i_mdio_read(struct mii_dev *bus, int addr, int devad, int reg) +{ + struct emac_eth_dev *priv = bus->priv; + ulong start; + u32 miiaddr = 0; + int timeout = CONFIG_MDIO_TIMEOUT; + + miiaddr &= ~MDIO_CMD_MII_WRITE; + miiaddr &= ~MDIO_CMD_MII_PHY_REG_ADDR_MASK; + miiaddr |= (reg << MDIO_CMD_MII_PHY_REG_ADDR_SHIFT) & + MDIO_CMD_MII_PHY_REG_ADDR_MASK; + + miiaddr &= ~MDIO_CMD_MII_PHY_ADDR_MASK; + + miiaddr |= (addr << MDIO_CMD_MII_PHY_ADDR_SHIFT) & + MDIO_CMD_MII_PHY_ADDR_MASK; + + miiaddr |= MDIO_CMD_MII_BUSY; + + writel(miiaddr, priv->mac_reg + EMAC_MII_CMD); + + start = get_timer(0); + while (get_timer(start) < timeout) { + if (!(readl(priv->mac_reg + EMAC_MII_CMD) & MDIO_CMD_MII_BUSY)) + return readl(priv->mac_reg + EMAC_MII_DATA); + udelay(10); + }; + + return -1; +} + +static int sun8i_mdio_write(struct mii_dev *bus, int addr, int devad, int reg, + u16 val) +{ + struct emac_eth_dev *priv = bus->priv; + ulong start; + u32 miiaddr = 0; + int ret = -1, timeout = CONFIG_MDIO_TIMEOUT; + + miiaddr &= ~MDIO_CMD_MII_PHY_REG_ADDR_MASK; + miiaddr |= (reg << MDIO_CMD_MII_PHY_REG_ADDR_SHIFT) & + MDIO_CMD_MII_PHY_REG_ADDR_MASK; + + miiaddr &= ~MDIO_CMD_MII_PHY_ADDR_MASK; + miiaddr |= (addr << MDIO_CMD_MII_PHY_ADDR_SHIFT) & + MDIO_CMD_MII_PHY_ADDR_MASK; + + miiaddr |= MDIO_CMD_MII_WRITE; + miiaddr |= MDIO_CMD_MII_BUSY; + + writel(miiaddr, priv->mac_reg + EMAC_MII_CMD); + writel(val, priv->mac_reg + EMAC_MII_DATA); + + start = get_timer(0); + while (get_timer(start) < timeout) { + if (!(readl(priv->mac_reg + EMAC_MII_CMD) & + MDIO_CMD_MII_BUSY)) { + ret = 0; + break; + } + udelay(10); + }; + + return ret; +} + +static int _sun8i_write_hwaddr(struct emac_eth_dev *priv, u8 *mac_id) +{ + u32 macid_lo, macid_hi; + + macid_lo = mac_id[0] + (mac_id[1] << 8) + (mac_id[2] << 16) + + (mac_id[3] << 24); + macid_hi = mac_id[4] + (mac_id[5] << 8); + + writel(macid_hi, priv->mac_reg + EMAC_ADDR0_HIGH); + writel(macid_lo, priv->mac_reg + EMAC_ADDR0_LOW); + + return 0; +} + +static void sun8i_adjust_link(struct emac_eth_dev *priv, + struct phy_device *phydev) +{ + u32 v; + + v = readl(priv->mac_reg + EMAC_CTL0); + + if (phydev->duplex) + v |= BIT(0); + else + v &= ~BIT(0); + + v &= ~0x0C; + + switch (phydev->speed) { + case 1000: + break; + case 100: + v |= BIT(2); + v |= BIT(3); + break; + case 10: + v |= BIT(3); + break; + } + writel(v, priv->mac_reg + EMAC_CTL0); +} + +static int sun8i_emac_set_syscon_ephy(struct emac_eth_dev *priv, u32 *reg) +{ + if (priv->use_internal_phy) { + /* H3 based SoC's that has an Internal 100MBit PHY + * needs to be configured and powered up before use + */ + *reg &= ~H3_EPHY_DEFAULT_MASK; + *reg |= H3_EPHY_DEFAULT_VALUE; + *reg |= priv->phyaddr << H3_EPHY_ADDR_SHIFT; + *reg &= ~H3_EPHY_SHUTDOWN; + *reg |= H3_EPHY_SELECT; + } else + /* This is to select External Gigabit PHY on + * the boards with H3 SoC. + */ + *reg &= ~H3_EPHY_SELECT; + + return 0; +} + +static int sun8i_emac_set_syscon(struct emac_eth_dev *priv) +{ + int ret; + u32 reg; + + reg = readl(priv->sysctl_reg); + + if (priv->variant == H3_EMAC) { + ret = sun8i_emac_set_syscon_ephy(priv, ®); + if (ret) + return ret; + } + + reg &= ~(SC_ETCS_MASK | SC_EPIT); + if (priv->variant == H3_EMAC || priv->variant == A64_EMAC) + reg &= ~SC_RMII_EN; + + switch (priv->interface) { + case PHY_INTERFACE_MODE_MII: + /* default */ + break; + case PHY_INTERFACE_MODE_RGMII: + reg |= SC_EPIT | SC_ETCS_INT_GMII; + break; + case PHY_INTERFACE_MODE_RMII: + if (priv->variant == H3_EMAC || + priv->variant == A64_EMAC) { + reg |= SC_RMII_EN | SC_ETCS_EXT_GMII; + break; + } + /* RMII not supported on A83T */ + default: + debug("%s: Invalid PHY interface\n", __func__); + return -EINVAL; + } + + writel(reg, priv->sysctl_reg); + + return 0; +} + +static int sun8i_phy_init(struct emac_eth_dev *priv, void *dev) +{ + struct phy_device *phydev; + + phydev = phy_connect(priv->bus, priv->phyaddr, dev, priv->interface); + if (!phydev) + return -ENODEV; + + phy_connect_dev(phydev, dev); + + priv->phydev = phydev; + phy_config(priv->phydev); + + return 0; +} + +static void rx_descs_init(struct emac_eth_dev *priv) +{ + struct emac_dma_desc *desc_table_p = &priv->rx_chain[0]; + char *rxbuffs = &priv->rxbuffer[0]; + struct emac_dma_desc *desc_p; + u32 idx; + + /* flush Rx buffers */ + flush_dcache_range((uintptr_t)rxbuffs, (ulong)rxbuffs + + RX_TOTAL_BUFSIZE); + + for (idx = 0; idx < CONFIG_RX_DESCR_NUM; idx++) { + desc_p = &desc_table_p[idx]; + desc_p->buf_addr = (uintptr_t)&rxbuffs[idx * CONFIG_ETH_BUFSIZE] + ; + desc_p->next = (uintptr_t)&desc_table_p[idx + 1]; + desc_p->st |= CONFIG_ETH_BUFSIZE; + desc_p->status = BIT(31); + } + + /* Correcting the last pointer of the chain */ + desc_p->next = (uintptr_t)&desc_table_p[0]; + + flush_dcache_range((uintptr_t)priv->rx_chain, + (uintptr_t)priv->rx_chain + + sizeof(priv->rx_chain)); + + writel((uintptr_t)&desc_table_p[0], (priv->mac_reg + EMAC_RX_DMA_DESC)); + priv->rx_currdescnum = 0; +} + +static void tx_descs_init(struct emac_eth_dev *priv) +{ + struct emac_dma_desc *desc_table_p = &priv->tx_chain[0]; + char *txbuffs = &priv->txbuffer[0]; + struct emac_dma_desc *desc_p; + u32 idx; + + for (idx = 0; idx < CONFIG_TX_DESCR_NUM; idx++) { + desc_p = &desc_table_p[idx]; + desc_p->buf_addr = (uintptr_t)&txbuffs[idx * CONFIG_ETH_BUFSIZE] + ; + desc_p->next = (uintptr_t)&desc_table_p[idx + 1]; + desc_p->status = (1 << 31); + desc_p->st = 0; + } + + /* Correcting the last pointer of the chain */ + desc_p->next = (uintptr_t)&desc_table_p[0]; + + /* Flush all Tx buffer descriptors */ + flush_dcache_range((uintptr_t)priv->tx_chain, + (uintptr_t)priv->tx_chain + + sizeof(priv->tx_chain)); + + writel((uintptr_t)&desc_table_p[0], priv->mac_reg + EMAC_TX_DMA_DESC); + priv->tx_currdescnum = 0; +} + +static int _sun8i_emac_eth_init(struct emac_eth_dev *priv, u8 *enetaddr) +{ + u32 reg, v; + int timeout = 100; + + reg = readl((priv->mac_reg + EMAC_CTL1)); + + if (!(reg & 0x1)) { + /* Soft reset MAC */ + setbits_le32((priv->mac_reg + EMAC_CTL1), 0x1); + do { + reg = readl(priv->mac_reg + EMAC_CTL1); + } while ((reg & 0x01) != 0 && (--timeout)); + if (!timeout) { + printf("%s: Timeout\n", __func__); + return -1; + } + } + + /* Rewrite mac address after reset */ + _sun8i_write_hwaddr(priv, enetaddr); + + v = readl(priv->mac_reg + EMAC_TX_CTL1); + /* TX_MD Transmission starts after a full frame located in TX DMA FIFO*/ + v |= BIT(1); + writel(v, priv->mac_reg + EMAC_TX_CTL1); + + v = readl(priv->mac_reg + EMAC_RX_CTL1); + /* RX_MD RX DMA reads data from RX DMA FIFO to host memory after a + * complete frame has been written to RX DMA FIFO + */ + v |= BIT(1); + writel(v, priv->mac_reg + EMAC_RX_CTL1); + + /* DMA */ + writel(8 << 24, priv->mac_reg + EMAC_CTL1); + + /* Initialize rx/tx descriptors */ + rx_descs_init(priv); + tx_descs_init(priv); + + /* PHY Start Up */ + genphy_parse_link(priv->phydev); + + sun8i_adjust_link(priv, priv->phydev); + + /* Start RX DMA */ + v = readl(priv->mac_reg + EMAC_RX_CTL1); + v |= BIT(30); + writel(v, priv->mac_reg + EMAC_RX_CTL1); + /* Start TX DMA */ + v = readl(priv->mac_reg + EMAC_TX_CTL1); + v |= BIT(30); + writel(v, priv->mac_reg + EMAC_TX_CTL1); + + /* Enable RX/TX */ + setbits_le32(priv->mac_reg + EMAC_RX_CTL0, BIT(31)); + setbits_le32(priv->mac_reg + EMAC_TX_CTL0, BIT(31)); + + return 0; +} + +static int parse_phy_pins(struct udevice *dev) +{ + int offset; + const char *pin_name; + int drive, pull, i; + + offset = fdtdec_lookup_phandle(gd->fdt_blob, dev->of_offset, + "pinctrl-0"); + if (offset < 0) { + printf("WARNING: emac: cannot find pinctrl-0 node\n"); + return offset; + } + + drive = fdt_getprop_u32_default_node(gd->fdt_blob, offset, 0, + "allwinner,drive", 4); + pull = fdt_getprop_u32_default_node(gd->fdt_blob, offset, 0, + "allwinner,pull", 0); + for (i = 0; ; i++) { + int pin; + + if (fdt_get_string_index(gd->fdt_blob, offset, + "allwinner,pins", i, &pin_name)) + break; + if (pin_name[0] != 'P') + continue; + pin = (pin_name[1] - 'A') << 5; + if (pin >= 26 << 5) + continue; + pin += simple_strtol(&pin_name[2], NULL, 10); + + sunxi_gpio_set_cfgpin(pin, SUN8I_GPD8_GMAC); + sunxi_gpio_set_drv(pin, drive); + sunxi_gpio_set_pull(pin, pull); + } + + if (!i) { + printf("WARNING: emac: cannot find allwinner,pins property\n"); + return -2; + } + + return 0; +} + +static int _sun8i_eth_recv(struct emac_eth_dev *priv, uchar **packetp) +{ + u32 status, desc_num = priv->rx_currdescnum; + struct emac_dma_desc *desc_p = &priv->rx_chain[desc_num]; + int length = -EAGAIN; + int good_packet = 1; + uintptr_t desc_start = (uintptr_t)desc_p; + uintptr_t desc_end = desc_start + + roundup(sizeof(*desc_p), ARCH_DMA_MINALIGN); + + ulong data_start = (uintptr_t)desc_p->buf_addr; + ulong data_end; + + /* Invalidate entire buffer descriptor */ + invalidate_dcache_range(desc_start, desc_end); + + status = desc_p->status; + + /* Check for DMA own bit */ + if (!(status & BIT(31))) { + length = (desc_p->status >> 16) & 0x3FFF; + + if (length < 0x40) { + good_packet = 0; + debug("RX: Bad Packet (runt)\n"); + } + + data_end = data_start + length; + /* Invalidate received data */ + invalidate_dcache_range(rounddown(data_start, + ARCH_DMA_MINALIGN), + roundup(data_end, + ARCH_DMA_MINALIGN)); + if (good_packet) { + if (length > CONFIG_ETH_BUFSIZE) { + printf("Received packet is too big (len=%d)\n", + length); + return -EMSGSIZE; + } + *packetp = (uchar *)(ulong)desc_p->buf_addr; + return length; + } + } + + return length; +} + +static int _sun8i_emac_eth_send(struct emac_eth_dev *priv, void *packet, + int len) +{ + u32 v, desc_num = priv->tx_currdescnum; + struct emac_dma_desc *desc_p = &priv->tx_chain[desc_num]; + uintptr_t desc_start = (uintptr_t)desc_p; + uintptr_t desc_end = desc_start + + roundup(sizeof(*desc_p), ARCH_DMA_MINALIGN); + + uintptr_t data_start = (uintptr_t)desc_p->buf_addr; + uintptr_t data_end = data_start + + roundup(len, ARCH_DMA_MINALIGN); + + /* Invalidate entire buffer descriptor */ + invalidate_dcache_range(desc_start, desc_end); + + desc_p->st = len; + /* Mandatory undocumented bit */ + desc_p->st |= BIT(24); + + memcpy((void *)data_start, packet, len); + + /* Flush data to be sent */ + flush_dcache_range(data_start, data_end); + + /* frame end */ + desc_p->st |= BIT(30); + desc_p->st |= BIT(31); + + /*frame begin */ + desc_p->st |= BIT(29); + desc_p->status = BIT(31); + + /*Descriptors st and status field has changed, so FLUSH it */ + flush_dcache_range(desc_start, desc_end); + + /* Move to next Descriptor and wrap around */ + if (++desc_num >= CONFIG_TX_DESCR_NUM) + desc_num = 0; + priv->tx_currdescnum = desc_num; + + /* Start the DMA */ + v = readl(priv->mac_reg + EMAC_TX_CTL1); + v |= BIT(31);/* mandatory */ + v |= BIT(30);/* mandatory */ + writel(v, priv->mac_reg + EMAC_TX_CTL1); + + return 0; +} + +static int sun8i_eth_write_hwaddr(struct udevice *dev) +{ + struct eth_pdata *pdata = dev_get_platdata(dev); + struct emac_eth_dev *priv = dev_get_priv(dev); + + return _sun8i_write_hwaddr(priv, pdata->enetaddr); +} + +static void sun8i_emac_board_setup(struct emac_eth_dev *priv) +{ + struct sunxi_ccm_reg *ccm = (struct sunxi_ccm_reg *)SUNXI_CCM_BASE; + + if (priv->use_internal_phy) { + /* Set clock gating for ephy */ + setbits_le32(&ccm->bus_gate4, BIT(AHB_GATE_OFFSET_EPHY)); + + /* Set Tx clock source as MII with rate 25 MZ */ + setbits_le32(priv->sysctl_reg, SCTL_EMAC_TX_CLK_SRC_MII | + SCTL_EMAC_EPIT_MII | SCTL_EMAC_CLK_SEL); + /* Deassert EPHY */ + setbits_le32(&ccm->ahb_reset2_cfg, BIT(AHB_RESET_OFFSET_EPHY)); + } + + /* Set clock gating for emac */ + setbits_le32(&ccm->ahb_gate0, BIT(AHB_GATE_OFFSET_GMAC)); + + /* Set EMAC clock */ + setbits_le32(&ccm->axi_gate, (BIT(1) | BIT(0))); + + /* De-assert EMAC */ + setbits_le32(&ccm->ahb_reset0_cfg, BIT(AHB_RESET_OFFSET_GMAC)); +} + +static int sun8i_mdio_init(const char *name, struct emac_eth_dev *priv) +{ + struct mii_dev *bus = mdio_alloc(); + + if (!bus) { + debug("Failed to allocate MDIO bus\n"); + return -ENOMEM; + } + + bus->read = sun8i_mdio_read; + bus->write = sun8i_mdio_write; + snprintf(bus->name, sizeof(bus->name), name); + bus->priv = (void *)priv; + + return mdio_register(bus); +} + +static int sun8i_emac_eth_start(struct udevice *dev) +{ + struct eth_pdata *pdata = dev_get_platdata(dev); + + return _sun8i_emac_eth_init(dev->priv, pdata->enetaddr); +} + +static int sun8i_emac_eth_send(struct udevice *dev, void *packet, int length) +{ + struct emac_eth_dev *priv = dev_get_priv(dev); + + return _sun8i_emac_eth_send(priv, packet, length); +} + +static int sun8i_emac_eth_recv(struct udevice *dev, int flags, uchar **packetp) +{ + struct emac_eth_dev *priv = dev_get_priv(dev); + + return _sun8i_eth_recv(priv, packetp); +} + +static int _sun8i_free_pkt(struct emac_eth_dev *priv) +{ + u32 desc_num = priv->rx_currdescnum; + struct emac_dma_desc *desc_p = &priv->rx_chain[desc_num]; + uintptr_t desc_start = (uintptr_t)desc_p; + uintptr_t desc_end = desc_start + + roundup(sizeof(u32), ARCH_DMA_MINALIGN); + + /* Make the current descriptor valid again */ + desc_p->status |= BIT(31); + + /* Flush Status field of descriptor */ + flush_dcache_range(desc_start, desc_end); + + /* Move to next desc and wrap-around condition. */ + if (++desc_num >= CONFIG_RX_DESCR_NUM) + desc_num = 0; + priv->rx_currdescnum = desc_num; + + return 0; +} + +static int sun8i_eth_free_pkt(struct udevice *dev, uchar *packet, + int length) +{ + struct emac_eth_dev *priv = dev_get_priv(dev); + + return _sun8i_free_pkt(priv); +} + +static void sun8i_emac_eth_stop(struct udevice *dev) +{ + struct emac_eth_dev *priv = dev_get_priv(dev); + + /* Stop Rx/Tx transmitter */ + clrbits_le32(priv->mac_reg + EMAC_RX_CTL0, BIT(31)); + clrbits_le32(priv->mac_reg + EMAC_TX_CTL0, BIT(31)); + + /* Stop TX DMA */ + clrbits_le32(priv->mac_reg + EMAC_TX_CTL1, BIT(30)); + + phy_shutdown(priv->phydev); +} + +static int sun8i_emac_eth_probe(struct udevice *dev) +{ + struct eth_pdata *pdata = dev_get_platdata(dev); + struct emac_eth_dev *priv = dev_get_priv(dev); + + priv->mac_reg = (void *)pdata->iobase; + + sun8i_emac_board_setup(priv); + + sun8i_mdio_init(dev->name, priv); + priv->bus = miiphy_get_dev_by_name(dev->name); + + sun8i_emac_set_syscon(priv); + + return sun8i_phy_init(priv, dev); +} + +static const struct eth_ops sun8i_emac_eth_ops = { + .start = sun8i_emac_eth_start, + .write_hwaddr = sun8i_eth_write_hwaddr, + .send = sun8i_emac_eth_send, + .recv = sun8i_emac_eth_recv, + .free_pkt = sun8i_eth_free_pkt, + .stop = sun8i_emac_eth_stop, +}; + +static int sun8i_emac_eth_ofdata_to_platdata(struct udevice *dev) +{ + struct eth_pdata *pdata = dev_get_platdata(dev); + struct emac_eth_dev *priv = dev_get_priv(dev); + const char *phy_mode; + int offset = 0; + + pdata->iobase = dev_get_addr_name(dev, "emac"); + priv->sysctl_reg = dev_get_addr_name(dev, "syscon"); + + pdata->phy_interface = -1; + priv->phyaddr = -1; + priv->use_internal_phy = false; + + offset = fdtdec_lookup_phandle(gd->fdt_blob, dev->of_offset, + "phy"); + if (offset > 0) + priv->phyaddr = fdtdec_get_int(gd->fdt_blob, offset, "reg", + -1); + + phy_mode = fdt_getprop(gd->fdt_blob, dev->of_offset, "phy-mode", NULL); + + if (phy_mode) + pdata->phy_interface = phy_get_interface_by_name(phy_mode); + printf("phy interface%d\n", pdata->phy_interface); + + if (pdata->phy_interface == -1) { + debug("%s: Invalid PHY interface '%s'\n", __func__, phy_mode); + return -EINVAL; + } + + priv->variant = dev_get_driver_data(dev); + + if (!priv->variant) { + printf("%s: Missing variant '%s'\n", __func__, + (char *)priv->variant); + return -EINVAL; + } + + if (priv->variant == H3_EMAC) { + if (fdt_getprop(gd->fdt_blob, dev->of_offset, + "allwinner,use-internal-phy", NULL)) + priv->use_internal_phy = true; + } + + priv->interface = pdata->phy_interface; + + if (!priv->use_internal_phy) + parse_phy_pins(dev); + + return 0; +} + +static const struct udevice_id sun8i_emac_eth_ids[] = { + {.compatible = "allwinner,sun8i-h3-emac", .data = (uintptr_t)H3_EMAC }, + {.compatible = "allwinner,sun50i-a64-emac", + .data = (uintptr_t)A64_EMAC }, + {.compatible = "allwinner,sun8i-a83t-emac", + .data = (uintptr_t)A83T_EMAC }, + { } +}; + +U_BOOT_DRIVER(eth_sun8i_emac) = { + .name = "eth_sun8i_emac", + .id = UCLASS_ETH, + .of_match = sun8i_emac_eth_ids, + .ofdata_to_platdata = sun8i_emac_eth_ofdata_to_platdata, + .probe = sun8i_emac_eth_probe, + .ops = &sun8i_emac_eth_ops, + .priv_auto_alloc_size = sizeof(struct emac_eth_dev), + .platdata_auto_alloc_size = sizeof(struct eth_pdata), + .flags = DM_FLAG_ALLOC_PRIV_DMA, +}; |