summaryrefslogtreecommitdiff
path: root/drivers
diff options
context:
space:
mode:
Diffstat (limited to 'drivers')
-rw-r--r--drivers/net/ne2000.c213
-rw-r--r--drivers/net/ne2000.h316
-rw-r--r--drivers/net/ne2000_base.h282
3 files changed, 456 insertions, 355 deletions
diff --git a/drivers/net/ne2000.c b/drivers/net/ne2000.c
index b100657..4928014 100644
--- a/drivers/net/ne2000.c
+++ b/drivers/net/ne2000.c
@@ -82,25 +82,11 @@ Add SNMP
#ifdef CONFIG_DRIVER_NE2000
-/* wor around udelay resetting OCR */
-static void my_udelay(long us) {
- long tmo;
-
- tmo = get_timer (0) + us * CFG_HZ / 1000000; /* will this be much greater than 0 ? */
- while (get_timer (0) < tmo);
-}
-
-#define mdelay(n) my_udelay((n)*1000)
-
+#define mdelay(n) udelay((n)*1000)
/* forward definition of function used for the uboot interface */
void uboot_push_packet_len(int len);
void uboot_push_tx_done(int key, int val);
-/* timeout for tx/rx in s */
-#define TOUT 5
-
-#define ETHER_ADDR_LEN 6
-
/*
------------------------------------------------------------------------
Debugging details
@@ -118,18 +104,18 @@ void uboot_push_tx_done(int key, int val);
#if DEBUG & 1
#define DEBUG_FUNCTION() do { printf("%s\n", __FUNCTION__); } while (0)
#define DEBUG_LINE() do { printf("%d\n", __LINE__); } while (0)
+#define PRINTK(args...) printf(args)
#else
#define DEBUG_FUNCTION() do {} while(0)
#define DEBUG_LINE() do {} while(0)
+#define PRINTK(args...)
#endif
-#include "ne2000.h"
+/* NE2000 base header file */
+#include "ne2000_base.h"
-#if DEBUG & 1
-#define PRINTK(args...) printf(args)
-#else
-#define PRINTK(args...)
-#endif
+/* Basic NE2000 chip support */
+#include "ne2000.h"
static dp83902a_priv_data_t nic; /* just one instance of the card supported */
@@ -137,8 +123,7 @@ static bool
dp83902a_init(void)
{
dp83902a_priv_data_t *dp = &nic;
- cyg_uint8* base;
- int i;
+ u8* base;
DEBUG_FUNCTION();
@@ -147,6 +132,7 @@ dp83902a_init(void)
DEBUG_LINE();
+#if defined(NE2000_BASIC_INIT)
/* Prepare ESA */
DP_OUT(base, DP_CR, DP_CR_NODMA | DP_CR_PAGE1); /* Select page 1 */
/* Use the address from the serial EEPROM */
@@ -163,6 +149,7 @@ dp83902a_init(void)
dp->esa[4],
dp->esa[5] );
+#endif /* NE2000_BASIC_INIT */
return true;
}
@@ -170,7 +157,7 @@ static void
dp83902a_stop(void)
{
dp83902a_priv_data_t *dp = &nic;
- cyg_uint8 *base = dp->base;
+ u8 *base = dp->base;
DEBUG_FUNCTION();
@@ -188,10 +175,10 @@ dp83902a_stop(void)
the hardware ready to send/receive packets.
*/
static void
-dp83902a_start(unsigned char * enaddr)
+dp83902a_start(u8 * enaddr)
{
dp83902a_priv_data_t *dp = &nic;
- cyg_uint8 *base = dp->base;
+ u8 *base = dp->base;
int i;
DEBUG_FUNCTION();
@@ -206,15 +193,20 @@ dp83902a_start(unsigned char * enaddr)
dp->tx1 = dp->tx2 = 0;
dp->tx_next = dp->tx_buf1;
dp->tx_started = false;
+ dp->running = true;
DP_OUT(base, DP_PSTART, dp->rx_buf_start); /* Receive ring start page */
DP_OUT(base, DP_BNDRY, dp->rx_buf_end-1); /* Receive ring boundary */
DP_OUT(base, DP_PSTOP, dp->rx_buf_end); /* Receive ring end page */
dp->rx_next = dp->rx_buf_start-1;
+ dp->running = true;
DP_OUT(base, DP_ISR, 0xFF); /* Clear any pending interrupts */
DP_OUT(base, DP_IMR, DP_IMR_All); /* Enable all interrupts */
DP_OUT(base, DP_CR, DP_CR_NODMA | DP_CR_PAGE1 | DP_CR_STOP); /* Select page 1 */
DP_OUT(base, DP_P1_CURP, dp->rx_buf_start); /* Current page - next free page for Rx */
+ dp->running = true;
for (i = 0; i < ETHER_ADDR_LEN; i++) {
+ /* FIXME */
+ //*((vu_short*)( base + ((DP_P1_PAR0 + i) * 2) + 0x1400)) = enaddr[i];
DP_OUT(base, DP_P1_PAR0+i, enaddr[i]);
}
/* Enable and start device */
@@ -222,6 +214,7 @@ dp83902a_start(unsigned char * enaddr)
DP_OUT(base, DP_TCR, DP_TCR_NORMAL); /* Normal transmit operations */
DP_OUT(base, DP_RCR, DP_RCR_AB); /* Accept broadcast, no errors, no multicast */
dp->running = true;
+
}
/*
@@ -234,7 +227,7 @@ static void
dp83902a_start_xmit(int start_page, int len)
{
dp83902a_priv_data_t *dp = (dp83902a_priv_data_t *) &nic;
- cyg_uint8 *base = dp->base;
+ u8 *base = dp->base;
DEBUG_FUNCTION();
@@ -259,10 +252,10 @@ dp83902a_start_xmit(int start_page, int len)
that there is free buffer space (dp->tx_next).
*/
static void
-dp83902a_send(unsigned char *data, int total_len, unsigned long key)
+dp83902a_send(u8 *data, int total_len, u32 key)
{
struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic;
- cyg_uint8 *base = dp->base;
+ u8 *base = dp->base;
int len, start_page, pkt_len, i, isr;
#if DEBUG & 4
int dx;
@@ -296,7 +289,7 @@ dp83902a_send(unsigned char *data, int total_len, unsigned long key)
/* but the code is extended a bit to do what Hitachi's monitor */
/* does (i.e., also read data). */
- cyg_uint16 tmp;
+ u16 tmp;
int len = 1;
DP_OUT(base, DP_RSAL, 0x100-len);
@@ -322,7 +315,7 @@ dp83902a_send(unsigned char *data, int total_len, unsigned long key)
/* Put data into buffer */
#if DEBUG & 4
- printf(" sg buf %08lx len %08x\n ", (unsigned long) data, len);
+ printf(" sg buf %08lx len %08x\n ", (u32)data, len);
dx = 0;
#endif
while (len > 0) {
@@ -330,6 +323,7 @@ dp83902a_send(unsigned char *data, int total_len, unsigned long key)
printf(" %02x", *data);
if (0 == (++dx % 16)) printf("\n ");
#endif
+
DP_OUT_DATA(dp->data, *data++);
len--;
}
@@ -358,6 +352,7 @@ dp83902a_send(unsigned char *data, int total_len, unsigned long key)
do {
DP_IN(base, DP_ISR, isr);
} while ((isr & DP_ISR_RDC) == 0);
+
/* Then disable DMA */
DP_OUT(base, DP_CR, DP_CR_PAGE0 | DP_CR_NODMA | DP_CR_START);
@@ -383,9 +378,9 @@ static void
dp83902a_RxEvent(void)
{
struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic;
- cyg_uint8 *base = dp->base;
- unsigned char rsr;
- unsigned char rcv_hdr[4];
+ u8 *base = dp->base;
+ u8 rsr;
+ u8 rcv_hdr[4];
int i, len, pkt, cur;
DEBUG_FUNCTION();
@@ -423,6 +418,7 @@ dp83902a_RxEvent(void)
CYGACC_CALL_IF_DELAY_US(10);
#endif
+ /* read header (get data size)*/
for (i = 0; i < sizeof(rcv_hdr);) {
DP_IN_DATA(dp->data, rcv_hdr[i++]);
}
@@ -432,7 +428,10 @@ dp83902a_RxEvent(void)
rcv_hdr[0], rcv_hdr[1], rcv_hdr[2], rcv_hdr[3]);
#endif
len = ((rcv_hdr[3] << 8) | rcv_hdr[2]) - sizeof(rcv_hdr);
+
+ /* data read */
uboot_push_packet_len(len);
+
if (rcv_hdr[1] == dp->rx_buf_start)
DP_OUT(base, DP_BNDRY, dp->rx_buf_end-1);
else
@@ -448,12 +447,12 @@ dp83902a_RxEvent(void)
efficient processing in the upper layers of the stack.
*/
static void
-dp83902a_recv(unsigned char *data, int len)
+dp83902a_recv(u8 *data, int len)
{
struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic;
- cyg_uint8 *base = dp->base;
+ u8 *base = dp->base;
int i, mlen;
- cyg_uint8 saved_char = 0;
+ u8 saved_char = 0;
bool saved;
#if DEBUG & 4
int dx;
@@ -482,7 +481,7 @@ dp83902a_recv(unsigned char *data, int len)
if (data) {
mlen = len;
#if DEBUG & 4
- printf(" sg buf %08lx len %08x \n", (unsigned long) data, mlen);
+ printf(" sg buf %08lx len %08x \n", (u32) data, mlen);
dx = 0;
#endif
while (0 < mlen) {
@@ -495,7 +494,7 @@ dp83902a_recv(unsigned char *data, int len)
}
{
- cyg_uint8 tmp;
+ u8 tmp;
DP_IN_DATA(dp->data, tmp);
#if DEBUG & 4
printf(" %02x", tmp);
@@ -516,9 +515,9 @@ static void
dp83902a_TxEvent(void)
{
struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic;
- cyg_uint8 *base = dp->base;
- unsigned char tsr;
- unsigned long key;
+ u8 *base = dp->base;
+ u8 tsr;
+ u32 key;
DEBUG_FUNCTION();
@@ -551,8 +550,8 @@ static void
dp83902a_ClearCounters(void)
{
struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic;
- cyg_uint8 *base = dp->base;
- cyg_uint8 cnt1, cnt2, cnt3;
+ u8 *base = dp->base;
+ u8 cnt1, cnt2, cnt3;
DP_IN(base, DP_FER, cnt1);
DP_IN(base, DP_CER, cnt2);
@@ -566,8 +565,8 @@ static void
dp83902a_Overflow(void)
{
struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *)&nic;
- cyg_uint8 *base = dp->base;
- cyg_uint8 isr;
+ u8 *base = dp->base;
+ u8 isr;
/* Issue a stop command and wait 1.6ms for it to complete. */
DP_OUT(base, DP_CR, DP_CR_STOP | DP_CR_NODMA);
@@ -603,8 +602,8 @@ static void
dp83902a_poll(void)
{
struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic;
- cyg_uint8 *base = dp->base;
- unsigned char isr;
+ u8 *base = dp->base;
+ u8 isr;
DP_OUT(base, DP_CR, DP_CR_NODMA | DP_CR_PAGE0 | DP_CR_START);
DP_IN(base, DP_ISR, isr);
@@ -642,13 +641,13 @@ dp83902a_poll(void)
/* find prom (taken from pc_net_cs.c from Linux) */
#include "8390.h"
-
+/*
typedef struct hw_info_t {
u_int offset;
u_char a0, a1, a2;
u_int flags;
} hw_info_t;
-
+*/
#define DELAY_OUTPUT 0x01
#define HAS_MISC_REG 0x02
#define USE_BIG_BUF 0x04
@@ -731,102 +730,17 @@ static hw_info_t hw_info[] = {
static hw_info_t default_info = { 0, 0, 0, 0, 0 };
-unsigned char dev_addr[6];
+u8 dev_addr[6];
#define PCNET_CMD 0x00
#define PCNET_DATAPORT 0x10 /* NatSemi-defined port window offset. */
#define PCNET_RESET 0x1f /* Issue a read to reset, a write to clear. */
#define PCNET_MISC 0x18 /* For IBM CCAE and Socket EA cards */
-unsigned long nic_base;
-
-static void pcnet_reset_8390(void)
-{
- int i, r;
-
- PRINTK("nic base is %lx\n", nic_base);
-
- n2k_outb(E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD);
- PRINTK("cmd (at %lx) is %x\n", nic_base+ E8390_CMD, n2k_inb(E8390_CMD));
- n2k_outb(E8390_NODMA+E8390_PAGE1+E8390_STOP, E8390_CMD);
- PRINTK("cmd (at %lx) is %x\n", nic_base+ E8390_CMD, n2k_inb(E8390_CMD));
- n2k_outb(E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD);
- PRINTK("cmd (at %lx) is %x\n", nic_base+ E8390_CMD, n2k_inb(E8390_CMD));
- n2k_outb(E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD);
-
- n2k_outb(n2k_inb(PCNET_RESET), PCNET_RESET);
-
- for (i = 0; i < 100; i++) {
- if ((r = (n2k_inb(EN0_ISR) & ENISR_RESET)) != 0)
- break;
- PRINTK("got %x in reset\n", r);
- my_udelay(100);
- }
- n2k_outb(ENISR_RESET, EN0_ISR); /* Ack intr. */
-
- if (i == 100)
- printf("pcnet_reset_8390() did not complete.\n");
-} /* pcnet_reset_8390 */
-
-static hw_info_t * get_prom(void ) {
- unsigned char prom[32];
- int i, j;
- struct {
- u_char value, offset;
- } program_seq[] = {
- {E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD}, /* Select page 0*/
- {0x48, EN0_DCFG}, /* Set byte-wide (0x48) access. */
- {0x00, EN0_RCNTLO}, /* Clear the count regs. */
- {0x00, EN0_RCNTHI},
- {0x00, EN0_IMR}, /* Mask completion irq. */
- {0xFF, EN0_ISR},
- {E8390_RXOFF, EN0_RXCR}, /* 0x20 Set to monitor */
- {E8390_TXOFF, EN0_TXCR}, /* 0x02 and loopback mode. */
- {32, EN0_RCNTLO},
- {0x00, EN0_RCNTHI},
- {0x00, EN0_RSARLO}, /* DMA starting at 0x0000. */
- {0x00, EN0_RSARHI},
- {E8390_RREAD+E8390_START, E8390_CMD},
- };
-
- PRINTK("trying to get MAC via prom reading\n");
-
- pcnet_reset_8390();
-
- mdelay(10);
-
- for (i = 0; i < sizeof(program_seq)/sizeof(program_seq[0]); i++)
- n2k_outb(program_seq[i].value, program_seq[i].offset);
-
- PRINTK("PROM:");
- for (i = 0; i < 32; i++) {
- prom[i] = n2k_inb(PCNET_DATAPORT);
- PRINTK(" %02x", prom[i]);
- }
- PRINTK("\n");
- for (i = 0; i < NR_INFO; i++) {
- if ((prom[0] == hw_info[i].a0) &&
- (prom[2] == hw_info[i].a1) &&
- (prom[4] == hw_info[i].a2)) {
- PRINTK("matched board %d\n", i);
- break;
- }
- }
- if ((i < NR_INFO) || ((prom[28] == 0x57) && (prom[30] == 0x57))) {
- for (j = 0; j < 6; j++)
- dev_addr[j] = prom[j<<1];
- PRINTK("on exit i is %d/%ld\n", i, NR_INFO);
- PRINTK("MAC address is %02x:%02x:%02x:%02x:%02x:%02x\n",
- dev_addr[0],dev_addr[1],dev_addr[2],dev_addr[3],dev_addr[4],dev_addr[5]);
- return (i < NR_INFO) ? hw_info+i : &default_info;
- }
- return NULL;
-}
+u32 nic_base;
/* U-boot specific routines */
-
-
-static unsigned char *pbuf = NULL;
+static u8 *pbuf = NULL;
static int pkey = -1;
static int initialized=0;
@@ -839,7 +753,7 @@ void uboot_push_packet_len(int len) {
}
dp83902a_recv(&pbuf[0], len);
- /* Just pass it to the upper layer */
+ /*Just pass it to the upper layer*/
NetReceive(&pbuf[0], len);
}
@@ -864,7 +778,7 @@ int eth_init(bd_t *bd) {
#ifdef CONFIG_DRIVER_NE2000_CCR
{
- volatile unsigned char *p = (volatile unsigned char *) CONFIG_DRIVER_NE2000_CCR;
+ vu_char *p = (vu_char *) CONFIG_DRIVER_NE2000_CCR;
PRINTK("CCR before is %x\n", *p);
*p = CONFIG_DRIVER_NE2000_VAL;
@@ -873,9 +787,9 @@ int eth_init(bd_t *bd) {
#endif
nic_base = CONFIG_DRIVER_NE2000_BASE;
- nic.base = (cyg_uint8 *) CONFIG_DRIVER_NE2000_BASE;
+ nic.base = (u8 *) CONFIG_DRIVER_NE2000_BASE;
- r = get_prom();
+ r = get_prom(dev_addr);
if (!r)
return -1;
@@ -886,22 +800,23 @@ int eth_init(bd_t *bd) {
PRINTK("Set environment from HW MAC addr = \"%s\"\n", ethaddr);
setenv ("ethaddr", ethaddr);
-
-#define DP_DATA 0x10
nic.data = nic.base + DP_DATA;
- nic.tx_buf1 = 0x40;
- nic.tx_buf2 = 0x48;
- nic.rx_buf_start = 0x50;
- nic.rx_buf_end = 0x80;
+ nic.tx_buf1 = START_PG;
+ nic.tx_buf2 = START_PG2;
+ nic.rx_buf_start = RX_START;
+ nic.rx_buf_end = RX_END;
if (dp83902a_init() == false)
return -1;
+
dp83902a_start(dev_addr);
initialized=1;
+
return 0;
}
void eth_halt() {
+
PRINTK("### eth_halt\n");
if(initialized)
dp83902a_stop();
@@ -920,7 +835,7 @@ int eth_send(volatile void *packet, int length) {
pkey = -1;
- dp83902a_send((unsigned char *) packet, length, 666);
+ dp83902a_send((u8 *) packet, length, 666);
tmo = get_timer (0) + TOUT * CFG_HZ;
while(1) {
dp83902a_poll();
diff --git a/drivers/net/ne2000.h b/drivers/net/ne2000.h
index c13d9f0..06e9a28 100644
--- a/drivers/net/ne2000.h
+++ b/drivers/net/ne2000.h
@@ -71,209 +71,113 @@ are GPL, so this is, of course, GPL.
*/
/*
- ------------------------------------------------------------------------
- Macros for accessing DP registers
- These can be overridden by the platform header
-*/
-
-#define DP_IN(_b_, _o_, _d_) (_d_) = *( (volatile unsigned char *) ((_b_)+(_o_)))
-#define DP_OUT(_b_, _o_, _d_) *( (volatile unsigned char *) ((_b_)+(_o_))) = (_d_)
-
-#define DP_IN_DATA(_b_, _d_) (_d_) = *( (volatile unsigned char *) ((_b_)))
-#define DP_OUT_DATA(_b_, _d_) *( (volatile unsigned char *) ((_b_))) = (_d_)
-
-
-/* here is all the data */
-
-#define cyg_uint8 unsigned char
-#define cyg_uint16 unsigned short
-#define bool int
-
-#define false 0
-#define true 1
-
-#define CYGHWR_NS_DP83902A_PLF_BROKEN_TX_DMA 1
-#define CYGACC_CALL_IF_DELAY_US(X) my_udelay(X)
-
-typedef struct dp83902a_priv_data {
- cyg_uint8* base;
- cyg_uint8* data;
- cyg_uint8* reset;
- int tx_next; /* First free Tx page */
- int tx_int; /* Expecting interrupt from this buffer */
- int rx_next; /* First free Rx page */
- int tx1, tx2; /* Page numbers for Tx buffers */
- unsigned long tx1_key, tx2_key; /* Used to ack when packet sent */
- int tx1_len, tx2_len;
- bool tx_started, running, hardwired_esa;
- cyg_uint8 esa[6];
- void* plf_priv;
-
- /* Buffer allocation */
- int tx_buf1, tx_buf2;
- int rx_buf_start, rx_buf_end;
-} dp83902a_priv_data_t;
-
-/*
- ------------------------------------------------------------------------
- Some forward declarations
-*/
-static void dp83902a_poll(void);
-
-/* ------------------------------------------------------------------------ */
-/* Register offsets */
-
-#define DP_CR 0x00
-#define DP_CLDA0 0x01
-#define DP_PSTART 0x01 /* write */
-#define DP_CLDA1 0x02
-#define DP_PSTOP 0x02 /* write */
-#define DP_BNDRY 0x03
-#define DP_TSR 0x04
-#define DP_TPSR 0x04 /* write */
-#define DP_NCR 0x05
-#define DP_TBCL 0x05 /* write */
-#define DP_FIFO 0x06
-#define DP_TBCH 0x06 /* write */
-#define DP_ISR 0x07
-#define DP_CRDA0 0x08
-#define DP_RSAL 0x08 /* write */
-#define DP_CRDA1 0x09
-#define DP_RSAH 0x09 /* write */
-#define DP_RBCL 0x0a /* write */
-#define DP_RBCH 0x0b /* write */
-#define DP_RSR 0x0c
-#define DP_RCR 0x0c /* write */
-#define DP_FER 0x0d
-#define DP_TCR 0x0d /* write */
-#define DP_CER 0x0e
-#define DP_DCR 0x0e /* write */
-#define DP_MISSED 0x0f
-#define DP_IMR 0x0f /* write */
-#define DP_DATAPORT 0x10 /* "eprom" data port */
-
-#define DP_P1_CR 0x00
-#define DP_P1_PAR0 0x01
-#define DP_P1_PAR1 0x02
-#define DP_P1_PAR2 0x03
-#define DP_P1_PAR3 0x04
-#define DP_P1_PAR4 0x05
-#define DP_P1_PAR5 0x06
-#define DP_P1_CURP 0x07
-#define DP_P1_MAR0 0x08
-#define DP_P1_MAR1 0x09
-#define DP_P1_MAR2 0x0a
-#define DP_P1_MAR3 0x0b
-#define DP_P1_MAR4 0x0c
-#define DP_P1_MAR5 0x0d
-#define DP_P1_MAR6 0x0e
-#define DP_P1_MAR7 0x0f
-
-#define DP_P2_CR 0x00
-#define DP_P2_PSTART 0x01
-#define DP_P2_CLDA0 0x01 /* write */
-#define DP_P2_PSTOP 0x02
-#define DP_P2_CLDA1 0x02 /* write */
-#define DP_P2_RNPP 0x03
-#define DP_P2_TPSR 0x04
-#define DP_P2_LNPP 0x05
-#define DP_P2_ACH 0x06
-#define DP_P2_ACL 0x07
-#define DP_P2_RCR 0x0c
-#define DP_P2_TCR 0x0d
-#define DP_P2_DCR 0x0e
-#define DP_P2_IMR 0x0f
-
-/* Command register - common to all pages */
-
-#define DP_CR_STOP 0x01 /* Stop: software reset */
-#define DP_CR_START 0x02 /* Start: initialize device */
-#define DP_CR_TXPKT 0x04 /* Transmit packet */
-#define DP_CR_RDMA 0x08 /* Read DMA (recv data from device) */
-#define DP_CR_WDMA 0x10 /* Write DMA (send data to device) */
-#define DP_CR_SEND 0x18 /* Send packet */
-#define DP_CR_NODMA 0x20 /* Remote (or no) DMA */
-#define DP_CR_PAGE0 0x00 /* Page select */
-#define DP_CR_PAGE1 0x40
-#define DP_CR_PAGE2 0x80
-#define DP_CR_PAGEMSK 0x3F /* Used to mask out page bits */
-
-/* Data configuration register */
-
-#define DP_DCR_WTS 0x01 /* 1=16 bit word transfers */
-#define DP_DCR_BOS 0x02 /* 1=Little Endian */
-#define DP_DCR_LAS 0x04 /* 1=Single 32 bit DMA mode */
-#define DP_DCR_LS 0x08 /* 1=normal mode, 0=loopback */
-#define DP_DCR_ARM 0x10 /* 0=no send command (program I/O) */
-#define DP_DCR_FIFO_1 0x00 /* FIFO threshold */
-#define DP_DCR_FIFO_2 0x20
-#define DP_DCR_FIFO_4 0x40
-#define DP_DCR_FIFO_6 0x60
-
-#define DP_DCR_INIT (DP_DCR_LS|DP_DCR_FIFO_4)
-
-/* Interrupt status register */
-
-#define DP_ISR_RxP 0x01 /* Packet received */
-#define DP_ISR_TxP 0x02 /* Packet transmitted */
-#define DP_ISR_RxE 0x04 /* Receive error */
-#define DP_ISR_TxE 0x08 /* Transmit error */
-#define DP_ISR_OFLW 0x10 /* Receive overflow */
-#define DP_ISR_CNT 0x20 /* Tally counters need emptying */
-#define DP_ISR_RDC 0x40 /* Remote DMA complete */
-#define DP_ISR_RESET 0x80 /* Device has reset (shutdown, error) */
-
-/* Interrupt mask register */
-
-#define DP_IMR_RxP 0x01 /* Packet received */
-#define DP_IMR_TxP 0x02 /* Packet transmitted */
-#define DP_IMR_RxE 0x04 /* Receive error */
-#define DP_IMR_TxE 0x08 /* Transmit error */
-#define DP_IMR_OFLW 0x10 /* Receive overflow */
-#define DP_IMR_CNT 0x20 /* Tall counters need emptying */
-#define DP_IMR_RDC 0x40 /* Remote DMA complete */
-
-#define DP_IMR_All 0x3F /* Everything but remote DMA */
-
-/* Receiver control register */
-
-#define DP_RCR_SEP 0x01 /* Save bad(error) packets */
-#define DP_RCR_AR 0x02 /* Accept runt packets */
-#define DP_RCR_AB 0x04 /* Accept broadcast packets */
-#define DP_RCR_AM 0x08 /* Accept multicast packets */
-#define DP_RCR_PROM 0x10 /* Promiscuous mode */
-#define DP_RCR_MON 0x20 /* Monitor mode - 1=accept no packets */
-
-/* Receiver status register */
-
-#define DP_RSR_RxP 0x01 /* Packet received */
-#define DP_RSR_CRC 0x02 /* CRC error */
-#define DP_RSR_FRAME 0x04 /* Framing error */
-#define DP_RSR_FO 0x08 /* FIFO overrun */
-#define DP_RSR_MISS 0x10 /* Missed packet */
-#define DP_RSR_PHY 0x20 /* 0=pad match, 1=mad match */
-#define DP_RSR_DIS 0x40 /* Receiver disabled */
-#define DP_RSR_DFR 0x80 /* Receiver processing deferred */
-
-/* Transmitter control register */
-
-#define DP_TCR_NOCRC 0x01 /* 1=inhibit CRC */
-#define DP_TCR_NORMAL 0x00 /* Normal transmitter operation */
-#define DP_TCR_LOCAL 0x02 /* Internal NIC loopback */
-#define DP_TCR_INLOOP 0x04 /* Full internal loopback */
-#define DP_TCR_OUTLOOP 0x08 /* External loopback */
-#define DP_TCR_ATD 0x10 /* Auto transmit disable */
-#define DP_TCR_OFFSET 0x20 /* Collision offset adjust */
-
-/* Transmit status register */
-
-#define DP_TSR_TxP 0x01 /* Packet transmitted */
-#define DP_TSR_COL 0x04 /* Collision (at least one) */
-#define DP_TSR_ABT 0x08 /* Aborted because of too many collisions */
-#define DP_TSR_CRS 0x10 /* Lost carrier */
-#define DP_TSR_FU 0x20 /* FIFO underrun */
-#define DP_TSR_CDH 0x40 /* Collision Detect Heartbeat */
-#define DP_TSR_OWC 0x80 /* Collision outside normal window */
-
-#define IEEE_8023_MAX_FRAME 1518 /* Largest possible ethernet frame */
-#define IEEE_8023_MIN_FRAME 64 /* Smallest possible ethernet frame */
+ * NE2000 support header file.
+ * Created by Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+ */
+
+#ifndef __DRIVERS_NE2000_H__
+#define __DRIVERS_NE2000_H__
+
+/* Enable NE2000 basic init function */
+#define NE2000_BASIC_INIT
+
+#define DP_DATA 0x10
+#define START_PG 0x50 /* First page of TX buffer */
+#define STOP_PG 0x80 /* Last page +1 of RX ring */
+
+#define RX_START 0x50
+#define RX_END 0x80
+
+#define DP_IN(_b_, _o_, _d_) (_d_) = *( (vu_char *) ((_b_)+(_o_)))
+#define DP_OUT(_b_, _o_, _d_) *( (vu_char *) ((_b_)+(_o_))) = (_d_)
+#define DP_IN_DATA(_b_, _d_) (_d_) = *( (vu_char *) ((_b_)))
+#define DP_OUT_DATA(_b_, _d_) *( (vu_char *) ((_b_))) = (_d_)
+
+static void pcnet_reset_8390(void)
+{
+ int i, r;
+
+ PRINTK("nic base is %lx\n", nic_base);
+
+ n2k_outb(E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD);
+ PRINTK("cmd (at %lx) is %x\n", nic_base+ E8390_CMD, n2k_inb(E8390_CMD));
+ n2k_outb(E8390_NODMA+E8390_PAGE1+E8390_STOP, E8390_CMD);
+ PRINTK("cmd (at %lx) is %x\n", nic_base+ E8390_CMD, n2k_inb(E8390_CMD));
+ n2k_outb(E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD);
+ PRINTK("cmd (at %lx) is %x\n", nic_base+ E8390_CMD, n2k_inb(E8390_CMD));
+ n2k_outb(E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD);
+
+ n2k_outb(n2k_inb(PCNET_RESET), PCNET_RESET);
+
+ for (i = 0; i < 100; i++) {
+ if ((r = (n2k_inb(EN0_ISR) & ENISR_RESET)) != 0)
+ break;
+ PRINTK("got %x in reset\n", r);
+ udelay(100);
+ }
+ n2k_outb(ENISR_RESET, EN0_ISR); /* Ack intr. */
+
+ if (i == 100)
+ printf("pcnet_reset_8390() did not complete.\n");
+} /* pcnet_reset_8390 */
+
+int get_prom(u8* mac_addr)
+{
+ u8 prom[32];
+ int i, j;
+ struct {
+ u_char value, offset;
+ } program_seq[] = {
+ {E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD}, /* Select page 0*/
+ {0x48, EN0_DCFG}, /* Set byte-wide (0x48) access. */
+ {0x00, EN0_RCNTLO}, /* Clear the count regs. */
+ {0x00, EN0_RCNTHI},
+ {0x00, EN0_IMR}, /* Mask completion irq. */
+ {0xFF, EN0_ISR},
+ {E8390_RXOFF, EN0_RXCR}, /* 0x20 Set to monitor */
+ {E8390_TXOFF, EN0_TXCR}, /* 0x02 and loopback mode. */
+ {32, EN0_RCNTLO},
+ {0x00, EN0_RCNTHI},
+ {0x00, EN0_RSARLO}, /* DMA starting at 0x0000. */
+ {0x00, EN0_RSARHI},
+ {E8390_RREAD+E8390_START, E8390_CMD},
+ };
+
+ PRINTK("trying to get MAC via prom reading\n");
+
+ pcnet_reset_8390();
+
+ mdelay(10);
+
+ for (i = 0; i < sizeof(program_seq)/sizeof(program_seq[0]); i++)
+ n2k_outb(program_seq[i].value, program_seq[i].offset);
+
+ PRINTK("PROM:");
+ for (i = 0; i < 32; i++) {
+ prom[i] = n2k_inb(PCNET_DATAPORT);
+ PRINTK(" %02x", prom[i]);
+ }
+ PRINTK("\n");
+ for (i = 0; i < NR_INFO; i++) {
+ if ((prom[0] == hw_info[i].a0) &&
+ (prom[2] == hw_info[i].a1) &&
+ (prom[4] == hw_info[i].a2)) {
+ PRINTK("matched board %d\n", i);
+ break;
+ }
+ }
+ if ((i < NR_INFO) || ((prom[28] == 0x57) && (prom[30] == 0x57))) {
+ PRINTK("on exit i is %d/%ld\n", i, NR_INFO);
+ PRINTK("MAC address is ");
+ for (j = 0; j < 6; j++){
+ mac_addr[j] = prom[j<<1];
+ PRINTK("%02x:",mac_addr[i]);
+ }
+ PRINTK("\n");
+ return (i < NR_INFO) ? i : 0;
+ }
+ return NULL;
+}
+
+
+#endif /* __DRIVERS_NE2000_H__ */
diff --git a/drivers/net/ne2000_base.h b/drivers/net/ne2000_base.h
new file mode 100644
index 0000000..1badf62
--- /dev/null
+++ b/drivers/net/ne2000_base.h
@@ -0,0 +1,282 @@
+/*
+Ported to U-Boot by Christian Pellegrin <chri@ascensit.com>
+
+Based on sources from the Linux kernel (pcnet_cs.c, 8390.h) and
+eCOS(if_dp83902a.c, if_dp83902a.h). Both of these 2 wonderful world
+are GPL, so this is, of course, GPL.
+
+
+==========================================================================
+
+ dev/dp83902a.h
+
+ National Semiconductor DP83902a ethernet chip
+
+==========================================================================
+####ECOSGPLCOPYRIGHTBEGIN####
+ -------------------------------------------
+ This file is part of eCos, the Embedded Configurable Operating System.
+ Copyright (C) 1998, 1999, 2000, 2001, 2002 Red Hat, Inc.
+
+ eCos is free software; you can redistribute it and/or modify it under
+ the terms of the GNU General Public License as published by the Free
+ Software Foundation; either version 2 or (at your option) any later version.
+
+ eCos is distributed in the hope that it will be useful, but WITHOUT ANY
+ WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ for more details.
+
+ You should have received a copy of the GNU General Public License along
+ with eCos; if not, write to the Free Software Foundation, Inc.,
+ 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
+
+ As a special exception, if other files instantiate templates or use macros
+ or inline functions from this file, or you compile this file and link it
+ with other works to produce a work based on this file, this file does not
+ by itself cause the resulting work to be covered by the GNU General Public
+ License. However the source code for this file must still be made available
+ in accordance with section (3) of the GNU General Public License.
+
+ This exception does not invalidate any other reasons why a work based on
+ this file might be covered by the GNU General Public License.
+
+ Alternative licenses for eCos may be arranged by contacting Red Hat, Inc.
+ at http://sources.redhat.com/ecos/ecos-license/
+ -------------------------------------------
+####ECOSGPLCOPYRIGHTEND####
+####BSDCOPYRIGHTBEGIN####
+
+ -------------------------------------------
+
+ Portions of this software may have been derived from OpenBSD or other sources,
+ and are covered by the appropriate copyright disclaimers included herein.
+
+ -------------------------------------------
+
+####BSDCOPYRIGHTEND####
+==========================================================================
+#####DESCRIPTIONBEGIN####
+
+ Author(s): gthomas
+ Contributors: gthomas, jskov
+ Date: 2001-06-13
+ Purpose:
+ Description:
+
+####DESCRIPTIONEND####
+
+==========================================================================
+
+*/
+
+/*
+ ------------------------------------------------------------------------
+ Macros for accessing DP registers
+ These can be overridden by the platform header
+*/
+
+#define bool int
+
+#define false 0
+#define true 1
+
+/* timeout for tx/rx in s */
+#define TOUT 5
+/* Ether MAC address size */
+#define ETHER_ADDR_LEN 6
+
+
+#define CYGHWR_NS_DP83902A_PLF_BROKEN_TX_DMA 1
+#define CYGACC_CALL_IF_DELAY_US(X) udelay(X)
+
+/* H/W infomation struct */
+typedef struct hw_info_t {
+ u32 offset;
+ u8 a0, a1, a2;
+ u32 flags;
+} hw_info_t;
+
+typedef struct dp83902a_priv_data {
+ u8* base;
+ u8* data;
+ u8* reset;
+ int tx_next; /* First free Tx page */
+ int tx_int; /* Expecting interrupt from this buffer */
+ int rx_next; /* First free Rx page */
+ int tx1, tx2; /* Page numbers for Tx buffers */
+ u32 tx1_key, tx2_key; /* Used to ack when packet sent */
+ int tx1_len, tx2_len;
+ bool tx_started, running, hardwired_esa;
+ u8 esa[6];
+ void* plf_priv;
+
+ /* Buffer allocation */
+ int tx_buf1, tx_buf2;
+ int rx_buf_start, rx_buf_end;
+} dp83902a_priv_data_t;
+
+/*
+ ------------------------------------------------------------------------
+ Some forward declarations
+*/
+int get_prom( u8* mac_addr);
+static void dp83902a_poll(void);
+
+/* ------------------------------------------------------------------------ */
+/* Register offsets */
+
+#define DP_CR 0x00
+#define DP_CLDA0 0x01
+#define DP_PSTART 0x01 /* write */
+#define DP_CLDA1 0x02
+#define DP_PSTOP 0x02 /* write */
+#define DP_BNDRY 0x03
+#define DP_TSR 0x04
+#define DP_TPSR 0x04 /* write */
+#define DP_NCR 0x05
+#define DP_TBCL 0x05 /* write */
+#define DP_FIFO 0x06
+#define DP_TBCH 0x06 /* write */
+#define DP_ISR 0x07
+#define DP_CRDA0 0x08
+#define DP_RSAL 0x08 /* write */
+#define DP_CRDA1 0x09
+#define DP_RSAH 0x09 /* write */
+#define DP_RBCL 0x0a /* write */
+#define DP_RBCH 0x0b /* write */
+#define DP_RSR 0x0c
+#define DP_RCR 0x0c /* write */
+#define DP_FER 0x0d
+#define DP_TCR 0x0d /* write */
+#define DP_CER 0x0e
+#define DP_DCR 0x0e /* write */
+#define DP_MISSED 0x0f
+#define DP_IMR 0x0f /* write */
+#define DP_DATAPORT 0x10 /* "eprom" data port */
+
+#define DP_P1_CR 0x00
+#define DP_P1_PAR0 0x01
+#define DP_P1_PAR1 0x02
+#define DP_P1_PAR2 0x03
+#define DP_P1_PAR3 0x04
+#define DP_P1_PAR4 0x05
+#define DP_P1_PAR5 0x06
+#define DP_P1_CURP 0x07
+#define DP_P1_MAR0 0x08
+#define DP_P1_MAR1 0x09
+#define DP_P1_MAR2 0x0a
+#define DP_P1_MAR3 0x0b
+#define DP_P1_MAR4 0x0c
+#define DP_P1_MAR5 0x0d
+#define DP_P1_MAR6 0x0e
+#define DP_P1_MAR7 0x0f
+
+#define DP_P2_CR 0x00
+#define DP_P2_PSTART 0x01
+#define DP_P2_CLDA0 0x01 /* write */
+#define DP_P2_PSTOP 0x02
+#define DP_P2_CLDA1 0x02 /* write */
+#define DP_P2_RNPP 0x03
+#define DP_P2_TPSR 0x04
+#define DP_P2_LNPP 0x05
+#define DP_P2_ACH 0x06
+#define DP_P2_ACL 0x07
+#define DP_P2_RCR 0x0c
+#define DP_P2_TCR 0x0d
+#define DP_P2_DCR 0x0e
+#define DP_P2_IMR 0x0f
+
+/* Command register - common to all pages */
+
+#define DP_CR_STOP 0x01 /* Stop: software reset */
+#define DP_CR_START 0x02 /* Start: initialize device */
+#define DP_CR_TXPKT 0x04 /* Transmit packet */
+#define DP_CR_RDMA 0x08 /* Read DMA (recv data from device) */
+#define DP_CR_WDMA 0x10 /* Write DMA (send data to device) */
+#define DP_CR_SEND 0x18 /* Send packet */
+#define DP_CR_NODMA 0x20 /* Remote (or no) DMA */
+#define DP_CR_PAGE0 0x00 /* Page select */
+#define DP_CR_PAGE1 0x40
+#define DP_CR_PAGE2 0x80
+#define DP_CR_PAGEMSK 0x3F /* Used to mask out page bits */
+
+/* Data configuration register */
+
+#define DP_DCR_WTS 0x01 /* 1=16 bit word transfers */
+#define DP_DCR_BOS 0x02 /* 1=Little Endian */
+#define DP_DCR_LAS 0x04 /* 1=Single 32 bit DMA mode */
+#define DP_DCR_LS 0x08 /* 1=normal mode, 0=loopback */
+#define DP_DCR_ARM 0x10 /* 0=no send command (program I/O) */
+#define DP_DCR_FIFO_1 0x00 /* FIFO threshold */
+#define DP_DCR_FIFO_2 0x20
+#define DP_DCR_FIFO_4 0x40
+#define DP_DCR_FIFO_6 0x60
+
+#define DP_DCR_INIT (DP_DCR_LS|DP_DCR_FIFO_4)
+
+/* Interrupt status register */
+
+#define DP_ISR_RxP 0x01 /* Packet received */
+#define DP_ISR_TxP 0x02 /* Packet transmitted */
+#define DP_ISR_RxE 0x04 /* Receive error */
+#define DP_ISR_TxE 0x08 /* Transmit error */
+#define DP_ISR_OFLW 0x10 /* Receive overflow */
+#define DP_ISR_CNT 0x20 /* Tally counters need emptying */
+#define DP_ISR_RDC 0x40 /* Remote DMA complete */
+#define DP_ISR_RESET 0x80 /* Device has reset (shutdown, error) */
+
+/* Interrupt mask register */
+
+#define DP_IMR_RxP 0x01 /* Packet received */
+#define DP_IMR_TxP 0x02 /* Packet transmitted */
+#define DP_IMR_RxE 0x04 /* Receive error */
+#define DP_IMR_TxE 0x08 /* Transmit error */
+#define DP_IMR_OFLW 0x10 /* Receive overflow */
+#define DP_IMR_CNT 0x20 /* Tall counters need emptying */
+#define DP_IMR_RDC 0x40 /* Remote DMA complete */
+
+#define DP_IMR_All 0x3F /* Everything but remote DMA */
+
+/* Receiver control register */
+
+#define DP_RCR_SEP 0x01 /* Save bad(error) packets */
+#define DP_RCR_AR 0x02 /* Accept runt packets */
+#define DP_RCR_AB 0x04 /* Accept broadcast packets */
+#define DP_RCR_AM 0x08 /* Accept multicast packets */
+#define DP_RCR_PROM 0x10 /* Promiscuous mode */
+#define DP_RCR_MON 0x20 /* Monitor mode - 1=accept no packets */
+
+/* Receiver status register */
+
+#define DP_RSR_RxP 0x01 /* Packet received */
+#define DP_RSR_CRC 0x02 /* CRC error */
+#define DP_RSR_FRAME 0x04 /* Framing error */
+#define DP_RSR_FO 0x08 /* FIFO overrun */
+#define DP_RSR_MISS 0x10 /* Missed packet */
+#define DP_RSR_PHY 0x20 /* 0=pad match, 1=mad match */
+#define DP_RSR_DIS 0x40 /* Receiver disabled */
+#define DP_RSR_DFR 0x80 /* Receiver processing deferred */
+
+/* Transmitter control register */
+
+#define DP_TCR_NOCRC 0x01 /* 1=inhibit CRC */
+#define DP_TCR_NORMAL 0x00 /* Normal transmitter operation */
+#define DP_TCR_LOCAL 0x02 /* Internal NIC loopback */
+#define DP_TCR_INLOOP 0x04 /* Full internal loopback */
+#define DP_TCR_OUTLOOP 0x08 /* External loopback */
+#define DP_TCR_ATD 0x10 /* Auto transmit disable */
+#define DP_TCR_OFFSET 0x20 /* Collision offset adjust */
+
+/* Transmit status register */
+
+#define DP_TSR_TxP 0x01 /* Packet transmitted */
+#define DP_TSR_COL 0x04 /* Collision (at least one) */
+#define DP_TSR_ABT 0x08 /* Aborted because of too many collisions */
+#define DP_TSR_CRS 0x10 /* Lost carrier */
+#define DP_TSR_FU 0x20 /* FIFO underrun */
+#define DP_TSR_CDH 0x40 /* Collision Detect Heartbeat */
+#define DP_TSR_OWC 0x80 /* Collision outside normal window */
+
+#define IEEE_8023_MAX_FRAME 1518 /* Largest possible ethernet frame */
+#define IEEE_8023_MIN_FRAME 64 /* Smallest possible ethernet frame */