diff options
Diffstat (limited to 'drivers')
| -rw-r--r-- | drivers/gpio/Kconfig | 7 | ||||
| -rw-r--r-- | drivers/gpio/Makefile | 1 | ||||
| -rw-r--r-- | drivers/gpio/lpc32xx_gpio.c | 293 | ||||
| -rw-r--r-- | drivers/hwmon/Makefile | 1 | ||||
| -rw-r--r-- | drivers/hwmon/ds620.c | 65 | ||||
| -rw-r--r-- | drivers/i2c/Makefile | 1 | ||||
| -rw-r--r-- | drivers/i2c/lpc32xx_i2c.c | 249 | ||||
| -rw-r--r-- | drivers/mtd/nand/Makefile | 1 | ||||
| -rw-r--r-- | drivers/mtd/nand/lpc32xx_nand_mlc.c | 764 | ||||
| -rw-r--r-- | drivers/net/Makefile | 1 | ||||
| -rw-r--r-- | drivers/net/lpc32xx_eth.c | 637 | ||||
| -rw-r--r-- | drivers/spi/Makefile | 1 | ||||
| -rw-r--r-- | drivers/spi/lpc32xx_ssp.c | 144 |
13 files changed, 2165 insertions, 0 deletions
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig index b609e73..7b5178a 100644 --- a/drivers/gpio/Kconfig +++ b/drivers/gpio/Kconfig @@ -7,3 +7,10 @@ config DM_GPIO the GPIO uclass. Drivers provide methods to query the particular GPIOs that they provide. The uclass interface is defined in include/asm-generic/gpio.h. + +config LPC32XX_GPIO + bool "LPC32XX GPIO driver" + depends on DM + default n + help + Support for the LPC32XX GPIO driver. diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile index fe9a3b2..85f71c5 100644 --- a/drivers/gpio/Makefile +++ b/drivers/gpio/Makefile @@ -41,3 +41,4 @@ obj-$(CONFIG_ADI_GPIO2) += adi_gpio2.o obj-$(CONFIG_TCA642X) += tca642x.o oby-$(CONFIG_SX151X) += sx151x.o obj-$(CONFIG_SUNXI_GPIO) += sunxi_gpio.o +obj-$(CONFIG_LPC32XX_GPIO) += lpc32xx_gpio.o diff --git a/drivers/gpio/lpc32xx_gpio.c b/drivers/gpio/lpc32xx_gpio.c new file mode 100644 index 0000000..96b3125 --- /dev/null +++ b/drivers/gpio/lpc32xx_gpio.c @@ -0,0 +1,293 @@ +/* + * LPC32xxGPIO driver + * + * (C) Copyright 2014 DENX Software Engineering GmbH + * Written-by: Albert ARIBAUD <albert.aribaud@3adev.fr> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <asm/io.h> +#include <asm/arch-lpc32xx/cpu.h> +#include <asm/arch-lpc32xx/gpio.h> +#include <asm-generic/gpio.h> +#include <dm.h> + +/** + * LPC32xx GPIOs work in banks but are non-homogeneous: + * - each bank holds a different number of GPIOs + * - some GPIOs are input/ouput, some input only, some output only; + * - some GPIOs have different meanings as an input and as an output; + * - some GPIOs are controlled on a given port and bit index, but + * read on another one. +* + * In order to keep this code simple, GPIOS are considered here as + * homogeneous and linear, from 0 to 127. + * + * ** WARNING #1 ** + * + * Client code is responsible for properly using valid GPIO numbers, + * including cases where a single physical GPIO has differing numbers + * for setting its direction, reading it and/or writing to it. + * + * ** WARNING #2 ** + * + * Please read NOTE in description of lpc32xx_gpio_get_function(). + */ + +#define LPC32XX_GPIOS 128 + +struct lpc32xx_gpio_platdata { + struct gpio_regs *regs; + /* GPIO FUNCTION: SEE WARNING #2 */ + signed char function[LPC32XX_GPIOS]; +}; + +/** + * We have 4 GPIO ports of 32 bits each + */ + +#define MAX_GPIO 128 + +#define GPIO_TO_PORT(gpio) ((gpio / 32) & 3) +#define GPIO_TO_RANK(gpio) (gpio % 32) +#define GPIO_TO_MASK(gpio) (1 << (gpio % 32)) + +/** + * Configure a GPIO number 'offset' as input + */ + +static int lpc32xx_gpio_direction_input(struct udevice *dev, unsigned offset) +{ + int port, mask; + struct lpc32xx_gpio_platdata *gpio_platdata = dev_get_platdata(dev); + struct gpio_regs *regs = gpio_platdata->regs; + + port = GPIO_TO_PORT(offset); + mask = GPIO_TO_MASK(offset); + + switch (port) { + case 0: + writel(mask, ®s->p0_dir_clr); + break; + case 1: + writel(mask, ®s->p1_dir_clr); + break; + case 2: + /* ports 2 and 3 share a common direction */ + case 3: + writel(mask, ®s->p2_p3_dir_clr); + break; + default: + return -1; + } + + /* GPIO FUNCTION: SEE WARNING #2 */ + gpio_platdata->function[offset] = GPIOF_INPUT; + + return 0; +} + +/** + * Get the value of a GPIO + */ + +static int lpc32xx_gpio_get_value(struct udevice *dev, unsigned offset) +{ + int port, rank, mask, value; + struct lpc32xx_gpio_platdata *gpio_platdata = dev_get_platdata(dev); + struct gpio_regs *regs = gpio_platdata->regs; + + port = GPIO_TO_PORT(offset); + + switch (port) { + case 0: + value = readl(®s->p0_inp_state); + break; + case 1: + value = readl(®s->p1_inp_state); + break; + case 2: + value = readl(®s->p2_inp_state); + break; + case 3: + value = readl(®s->p3_inp_state); + break; + default: + return -1; + } + + rank = GPIO_TO_RANK(offset); + mask = GPIO_TO_MASK(offset); + + return (value & mask) >> rank; +} + +/** + * Set a GPIO + */ + +static int gpio_set(struct udevice *dev, unsigned gpio) +{ + int port, mask; + struct lpc32xx_gpio_platdata *gpio_platdata = dev_get_platdata(dev); + struct gpio_regs *regs = gpio_platdata->regs; + + port = GPIO_TO_PORT(gpio); + mask = GPIO_TO_MASK(gpio); + + switch (port) { + case 0: + writel(mask, ®s->p0_outp_set); + break; + case 1: + writel(mask, ®s->p1_outp_set); + break; + case 2: + writel(mask, ®s->p2_outp_set); + break; + case 3: + writel(mask, ®s->p3_outp_set); + break; + default: + return -1; + } + return 0; +} + +/** + * Clear a GPIO + */ + +static int gpio_clr(struct udevice *dev, unsigned gpio) +{ + int port, mask; + struct lpc32xx_gpio_platdata *gpio_platdata = dev_get_platdata(dev); + struct gpio_regs *regs = gpio_platdata->regs; + + port = GPIO_TO_PORT(gpio); + mask = GPIO_TO_MASK(gpio); + + switch (port) { + case 0: + writel(mask, ®s->p0_outp_clr); + break; + case 1: + writel(mask, ®s->p1_outp_clr); + break; + case 2: + writel(mask, ®s->p2_outp_clr); + break; + case 3: + writel(mask, ®s->p3_outp_clr); + break; + default: + return -1; + } + return 0; +} + +/** + * Set the value of a GPIO + */ + +static int lpc32xx_gpio_set_value(struct udevice *dev, unsigned offset, + int value) +{ + if (value) + return gpio_set(dev, offset); + else + return gpio_clr(dev, offset); +} + +/** + * Configure a GPIO number 'offset' as output with given initial value. + */ + +static int lpc32xx_gpio_direction_output(struct udevice *dev, unsigned offset, + int value) +{ + int port, mask; + struct lpc32xx_gpio_platdata *gpio_platdata = dev_get_platdata(dev); + struct gpio_regs *regs = gpio_platdata->regs; + + port = GPIO_TO_PORT(offset); + mask = GPIO_TO_MASK(offset); + + switch (port) { + case 0: + writel(mask, ®s->p0_dir_set); + break; + case 1: + writel(mask, ®s->p1_dir_set); + break; + case 2: + /* ports 2 and 3 share a common direction */ + case 3: + writel(mask, ®s->p2_p3_dir_set); + break; + default: + return -1; + } + + /* GPIO FUNCTION: SEE WARNING #2 */ + gpio_platdata->function[offset] = GPIOF_OUTPUT; + + return lpc32xx_gpio_set_value(dev, offset, value); +} + +/** + * GPIO functions are supposed to be computed from their current + * configuration, but that's way too complicated in LPC32XX. A simpler + * approach is used, where the GPIO functions are cached in an array. + * When the GPIO is in use, its function is either "input" or "output" + * depending on its direction, otherwise its function is "unknown". + * + * ** NOTE ** + * + * THIS APPROACH WAS CHOSEN DU TO THE COMPLEX NATURE OF THE LPC32XX + * GPIOS; DO NOT TAKE THIS AS AN EXAMPLE FOR NEW CODE. + */ + +static int lpc32xx_gpio_get_function(struct udevice *dev, unsigned offset) +{ + struct lpc32xx_gpio_platdata *gpio_platdata = dev_get_platdata(dev); + return gpio_platdata->function[offset]; +} + +static const struct dm_gpio_ops gpio_lpc32xx_ops = { + .direction_input = lpc32xx_gpio_direction_input, + .direction_output = lpc32xx_gpio_direction_output, + .get_value = lpc32xx_gpio_get_value, + .set_value = lpc32xx_gpio_set_value, + .get_function = lpc32xx_gpio_get_function, +}; + +static int lpc32xx_gpio_probe(struct udevice *dev) +{ + struct lpc32xx_gpio_platdata *gpio_platdata = dev_get_platdata(dev); + struct gpio_dev_priv *uc_priv = dev->uclass_priv; + + if (dev->of_offset == -1) { + /* Tell the uclass how many GPIOs we have */ + uc_priv->gpio_count = LPC32XX_GPIOS; + } + + /* set base address for GPIO registers */ + gpio_platdata->regs = (struct gpio_regs *)GPIO_BASE; + + /* all GPIO functions are unknown until requested */ + /* GPIO FUNCTION: SEE WARNING #2 */ + memset(gpio_platdata->function, GPIOF_UNKNOWN, + sizeof(gpio_platdata->function)); + + return 0; +} + +U_BOOT_DRIVER(gpio_lpc32xx) = { + .name = "gpio_lpc32xx", + .id = UCLASS_GPIO, + .ops = &gpio_lpc32xx_ops, + .probe = lpc32xx_gpio_probe, + .priv_auto_alloc_size = sizeof(struct lpc32xx_gpio_platdata), +}; diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile index 25b8e8a..b4fb057 100644 --- a/drivers/hwmon/Makefile +++ b/drivers/hwmon/Makefile @@ -15,6 +15,7 @@ obj-$(CONFIG_DTT_ADT7460) += adt7460.o obj-$(CONFIG_DTT_DS1621) += ds1621.o obj-$(CONFIG_DTT_DS1722) += ds1722.o obj-$(CONFIG_DTT_DS1775) += ds1775.o +obj-$(CONFIG_DTT_DS620) += ds620.o obj-$(CONFIG_DTT_LM63) += lm63.o obj-$(CONFIG_DTT_LM73) += lm73.o obj-$(CONFIG_DTT_LM75) += lm75.o diff --git a/drivers/hwmon/ds620.c b/drivers/hwmon/ds620.c new file mode 100644 index 0000000..1ecc3da --- /dev/null +++ b/drivers/hwmon/ds620.c @@ -0,0 +1,65 @@ +/* + * DS620 DTT support + * + * (C) Copyright 2014 3ADEV <http://www.3adev.com> + * Written-by: Albert ARIBAUD <albert.aribaud@3adev.fr> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* + * Dallas Semiconductor's DS1621/1631 Digital Thermometer and Thermostat. + */ + +#include <common.h> +#include <i2c.h> +#include <dtt.h> + +/* + * Device code + */ +#define DTT_I2C_DEV_CODE 0x48 +#define DTT_START_CONVERT 0x51 +#define DTT_TEMP 0xAA +#define DTT_CONFIG 0xAC + +/* + * Config register MSB bits + */ +#define DTT_CONFIG_1SHOT 0x01 +#define DTT_CONFIG_AUTOC 0x02 +#define DTT_CONFIG_R0 0x04 /* always 1 */ +#define DTT_CONFIG_R1 0x08 /* always 1 */ +#define DTT_CONFIG_TLF 0x10 +#define DTT_CONFIG_THF 0x20 +#define DTT_CONFIG_NVB 0x40 +#define DTT_CONFIG_DONE 0x80 + +#define CHIP(sensor) (DTT_I2C_DEV_CODE + (sensor & 0x07)) + +int dtt_init_one(int sensor) +{ + uint8_t config = DTT_CONFIG_1SHOT + | DTT_CONFIG_R0 + | DTT_CONFIG_R1; + return i2c_write(CHIP(sensor), DTT_CONFIG, 1, &config, 1); +} + +int dtt_get_temp(int sensor) +{ + uint8_t status; + uint8_t temp[2]; + + /* Start a conversion, may take up to 1 second. */ + i2c_write(CHIP(sensor), DTT_START_CONVERT, 1, NULL, 0); + do { + if (i2c_read(CHIP(sensor), DTT_CONFIG, 1, &status, 1)) + /* bail out if I2C error */ + status |= DTT_CONFIG_DONE; + } while (!(status & DTT_CONFIG_DONE)); + if (i2c_read(CHIP(sensor), DTT_TEMP, 1, temp, 2)) + /* bail out if I2C error */ + return -274; /* below absolute zero == error */ + + return ((int16_t)(temp[1] | (temp[0] << 8))) >> 7; +} diff --git a/drivers/i2c/Makefile b/drivers/i2c/Makefile index 774bc94..26ea854 100644 --- a/drivers/i2c/Makefile +++ b/drivers/i2c/Makefile @@ -20,6 +20,7 @@ obj-$(CONFIG_SYS_I2C_FSL) += fsl_i2c.o obj-$(CONFIG_SYS_I2C_FTI2C010) += fti2c010.o obj-$(CONFIG_SYS_I2C_IHS) += ihs_i2c.o obj-$(CONFIG_SYS_I2C_KONA) += kona_i2c.o +obj-$(CONFIG_SYS_I2C_LPC32XX) += lpc32xx_i2c.o obj-$(CONFIG_SYS_I2C_MVTWSI) += mvtwsi.o obj-$(CONFIG_SYS_I2C_MXC) += mxc_i2c.o obj-$(CONFIG_SYS_I2C_MXS) += mxs_i2c.o diff --git a/drivers/i2c/lpc32xx_i2c.c b/drivers/i2c/lpc32xx_i2c.c new file mode 100644 index 0000000..78d26e4 --- /dev/null +++ b/drivers/i2c/lpc32xx_i2c.c @@ -0,0 +1,249 @@ +/* + * LPC32xx I2C interface driver + * + * (C) Copyright 2014 DENX Software Engineering GmbH + * Written-by: Albert ARIBAUD - 3ADEV <albert.aribaud@3adev.fr> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/io.h> +#include <i2c.h> +#include <asm/errno.h> +#include <asm/arch/clk.h> + +/* + * Provide default speed and slave if target did not + */ + +#if !defined(CONFIG_SYS_I2C_LPC32XX_SPEED) +#define CONFIG_SYS_I2C_LPC32XX_SPEED 350000 +#endif + +#if !defined(CONFIG_SYS_I2C_LPC32XX_SLAVE) +#define CONFIG_SYS_I2C_LPC32XX_SLAVE 0 +#endif + +/* i2c register set */ +struct lpc32xx_i2c_registers { + union { + u32 rx; + u32 tx; + }; + u32 stat; + u32 ctrl; + u32 clk_hi; + u32 clk_lo; + u32 adr; + u32 rxfl; + u32 txfl; + u32 rxb; + u32 txb; + u32 stx; + u32 stxfl; +}; + +/* TX register fields */ +#define LPC32XX_I2C_TX_START 0x00000100 +#define LPC32XX_I2C_TX_STOP 0x00000200 + +/* Control register values */ +#define LPC32XX_I2C_SOFT_RESET 0x00000100 + +/* Status register values */ +#define LPC32XX_I2C_STAT_TFF 0x00000400 +#define LPC32XX_I2C_STAT_RFE 0x00000200 +#define LPC32XX_I2C_STAT_DRMI 0x00000008 +#define LPC32XX_I2C_STAT_NAI 0x00000004 +#define LPC32XX_I2C_STAT_TDI 0x00000001 + +static struct lpc32xx_i2c_registers *lpc32xx_i2c[] = { + (struct lpc32xx_i2c_registers *)I2C1_BASE, + (struct lpc32xx_i2c_registers *)I2C2_BASE +}; + +/* Set I2C bus speed */ +static unsigned int lpc32xx_i2c_set_bus_speed(struct i2c_adapter *adap, + unsigned int speed) +{ + int half_period; + + if (speed == 0) + return -EINVAL; + + half_period = (105000000 / speed) / 2; + + if ((half_period > 255) || (half_period < 0)) + return -EINVAL; + + writel(half_period, &lpc32xx_i2c[adap->hwadapnr]->clk_hi); + writel(half_period, &lpc32xx_i2c[adap->hwadapnr]->clk_lo); + return 0; +} + +/* I2C init called by cmd_i2c when doing 'i2c reset'. */ +static void _i2c_init(struct i2c_adapter *adap, + int requested_speed, int slaveadd) +{ + struct lpc32xx_i2c_registers *i2c = lpc32xx_i2c[adap->hwadapnr]; + + /* soft reset (auto-clears) */ + writel(LPC32XX_I2C_SOFT_RESET, &i2c->ctrl); + /* set HI and LO periods for about 350 kHz */ + lpc32xx_i2c_set_bus_speed(adap, requested_speed); +} + +/* I2C probe called by cmd_i2c when doing 'i2c probe'. */ +static int lpc32xx_i2c_probe(struct i2c_adapter *adap, u8 dev) +{ + struct lpc32xx_i2c_registers *i2c = lpc32xx_i2c[adap->hwadapnr]; + int stat; + + /* Soft-reset the controller */ + writel(LPC32XX_I2C_SOFT_RESET, &i2c->ctrl); + while (readl(&i2c->ctrl) & LPC32XX_I2C_SOFT_RESET) + ; + /* Addre slave for write with start before and stop after */ + writel((dev<<1) | LPC32XX_I2C_TX_START | LPC32XX_I2C_TX_STOP, + &i2c->tx); + /* wait for end of transation */ + while (!((stat = readl(&i2c->stat)) & LPC32XX_I2C_STAT_TDI)) + ; + /* was there no acknowledge? */ + return (stat & LPC32XX_I2C_STAT_NAI) ? -1 : 0; +} + +/* + * I2C read called by cmd_i2c when doing 'i2c read' and by cmd_eeprom.c + * Begin write, send address byte(s), begin read, receive data bytes, end. + */ +static int lpc32xx_i2c_read(struct i2c_adapter *adap, u8 dev, uint addr, + int alen, u8 *data, int length) +{ + struct lpc32xx_i2c_registers *i2c = lpc32xx_i2c[adap->hwadapnr]; + int stat, wlen; + + /* Soft-reset the controller */ + writel(LPC32XX_I2C_SOFT_RESET, &i2c->ctrl); + while (readl(&i2c->ctrl) & LPC32XX_I2C_SOFT_RESET) + ; + /* do we need to write an address at all? */ + if (alen) { + /* Address slave in write mode */ + writel((dev<<1) | LPC32XX_I2C_TX_START, &i2c->tx); + /* write address bytes */ + while (alen--) { + /* compute address byte + stop for the last one */ + int a = (addr >> (8 * alen)) & 0xff; + if (!alen) + a |= LPC32XX_I2C_TX_STOP; + /* Send address byte */ + writel(a, &i2c->tx); + } + /* wait for end of transation */ + while (!((stat = readl(&i2c->stat)) & LPC32XX_I2C_STAT_TDI)) + ; + /* clear end-of-transaction flag */ + writel(1, &i2c->stat); + } + /* do we have to read data at all? */ + if (length) { + /* Address slave in read mode */ + writel(1 | (dev<<1) | LPC32XX_I2C_TX_START, &i2c->tx); + wlen = length; + /* get data */ + while (length | wlen) { + /* read status for TFF and RFE */ + stat = readl(&i2c->stat); + /* must we, can we write a trigger byte? */ + if ((wlen > 0) + & (!(stat & LPC32XX_I2C_STAT_TFF))) { + wlen--; + /* write trigger byte + stop if last */ + writel(wlen ? 0 : + LPC32XX_I2C_TX_STOP, &i2c->tx); + } + /* must we, can we read a data byte? */ + if ((length > 0) + & (!(stat & LPC32XX_I2C_STAT_RFE))) { + length--; + /* read byte */ + *(data++) = readl(&i2c->rx); + } + } + } + /* wait for end of transation */ + while (!((stat = readl(&i2c->stat)) & LPC32XX_I2C_STAT_TDI)) + ; + /* clear end-of-transaction flag */ + writel(1, &i2c->stat); + /* success */ + return 0; +} + +/* + * I2C write called by cmd_i2c when doing 'i2c write' and by cmd_eeprom.c + * Begin write, send address byte(s), send data bytes, end. + */ +static int lpc32xx_i2c_write(struct i2c_adapter *adap, u8 dev, uint addr, + int alen, u8 *data, int length) +{ + struct lpc32xx_i2c_registers *i2c = lpc32xx_i2c[adap->hwadapnr]; + int stat; + + /* Soft-reset the controller */ + writel(LPC32XX_I2C_SOFT_RESET, &i2c->ctrl); + while (readl(&i2c->ctrl) & LPC32XX_I2C_SOFT_RESET) + ; + /* do we need to write anything at all? */ + if (alen | length) + /* Address slave in write mode */ + writel((dev<<1) | LPC32XX_I2C_TX_START, &i2c->tx); + /* write address bytes */ + while (alen) { + /* wait for transmit fifo not full */ + stat = readl(&i2c->stat); + if (!(stat & LPC32XX_I2C_STAT_TFF)) { + alen--; + int a = (addr >> (8 * alen)) & 0xff; + if (!(alen | length)) + a |= LPC32XX_I2C_TX_STOP; + /* Send address byte */ + writel(a, &i2c->tx); + } + } + while (length) { + /* wait for transmit fifo not full */ + stat = readl(&i2c->stat); + if (!(stat & LPC32XX_I2C_STAT_TFF)) { + /* compute data byte, add stop if length==0 */ + length--; + int d = *(data++); + if (!length) + d |= LPC32XX_I2C_TX_STOP; + /* Send data byte */ + writel(d, &i2c->tx); + } + } + /* wait for end of transation */ + while (!((stat = readl(&i2c->stat)) & LPC32XX_I2C_STAT_TDI)) + ; + /* clear end-of-transaction flag */ + writel(1, &i2c->stat); + return 0; +} + +U_BOOT_I2C_ADAP_COMPLETE(lpc32xx_0, _i2c_init, lpc32xx_i2c_probe, + lpc32xx_i2c_read, lpc32xx_i2c_write, + lpc32xx_i2c_set_bus_speed, + CONFIG_SYS_I2C_LPC32XX_SPEED, + CONFIG_SYS_I2C_LPC32XX_SLAVE, + 0) + +U_BOOT_I2C_ADAP_COMPLETE(lpc32xx_1, _i2c_init, lpc32xx_i2c_probe, + lpc32xx_i2c_read, lpc32xx_i2c_write, + lpc32xx_i2c_set_bus_speed, + CONFIG_SYS_I2C_LPC32XX_SPEED, + CONFIG_SYS_I2C_LPC32XX_SLAVE, + 1) diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile index 1f02bfc..347ea62 100644 --- a/drivers/mtd/nand/Makefile +++ b/drivers/mtd/nand/Makefile @@ -52,6 +52,7 @@ obj-$(CONFIG_NAND_JZ4740) += jz4740_nand.o obj-$(CONFIG_NAND_KB9202) += kb9202_nand.o obj-$(CONFIG_NAND_KIRKWOOD) += kirkwood_nand.o obj-$(CONFIG_NAND_KMETER1) += kmeter1_nand.o +obj-$(CONFIG_NAND_LPC32XX_MLC) += lpc32xx_nand_mlc.o obj-$(CONFIG_NAND_MPC5121_NFC) += mpc5121_nfc.o obj-$(CONFIG_NAND_VF610_NFC) += vf610_nfc.o obj-$(CONFIG_NAND_MXC) += mxc_nand.o diff --git a/drivers/mtd/nand/lpc32xx_nand_mlc.c b/drivers/mtd/nand/lpc32xx_nand_mlc.c new file mode 100644 index 0000000..8156fe9 --- /dev/null +++ b/drivers/mtd/nand/lpc32xx_nand_mlc.c @@ -0,0 +1,764 @@ +/* + * LPC32xx MLC NAND flash controller driver + * + * (C) Copyright 2014 3ADEV <http://3adev.com> + * Written by Albert ARIBAUD <albert.aribaud@3adev.fr> + * + * SPDX-License-Identifier: GPL-2.0+ + * + * NOTE: + * + * The MLC NAND flash controller provides hardware Reed-Solomon ECC + * covering in- and out-of-band data together. Therefore, in- and out- + * of-band data must be written together in order to have a valid ECC. + * + * Consequently, pages with meaningful in-band data are written with + * blank (all-ones) out-of-band data and a valid ECC, and any later + * out-of-band data write will void the ECC. + * + * Therefore, code which reads such late-written out-of-band data + * should not rely on the ECC validity. + */ + +#include <common.h> +#include <nand.h> +#include <asm/errno.h> +#include <asm/io.h> +#include <nand.h> +#include <asm/arch/clk.h> +#include <asm/arch/sys_proto.h> + +/* + * MLC NAND controller registers. + */ +struct lpc32xx_nand_mlc_registers { + u8 buff[32768]; /* controller's serial data buffer */ + u8 data[32768]; /* NAND's raw data buffer */ + u32 cmd; + u32 addr; + u32 ecc_enc_reg; + u32 ecc_dec_reg; + u32 ecc_auto_enc_reg; + u32 ecc_auto_dec_reg; + u32 rpr; + u32 wpr; + u32 rubp; + u32 robp; + u32 sw_wp_add_low; + u32 sw_wp_add_hig; + u32 icr; + u32 time_reg; + u32 irq_mr; + u32 irq_sr; + u32 lock_pr; + u32 isr; + u32 ceh; +}; + +/* LOCK_PR register defines */ +#define LOCK_PR_UNLOCK_KEY 0x0000A25E /* Magic unlock value */ + +/* ICR defines */ +#define ICR_LARGE_BLOCKS 0x00000004 /* configure for 2KB blocks */ +#define ICR_ADDR4 0x00000002 /* configure for 4-word addrs */ + +/* CEH defines */ +#define CEH_NORMAL_CE 0x00000001 /* do not force CE ON */ + +/* ISR register defines */ +#define ISR_NAND_READY 0x00000001 +#define ISR_CONTROLLER_READY 0x00000002 +#define ISR_ECC_READY 0x00000004 +#define ISR_DECODER_ERRORS(s) ((((s) >> 4) & 3)+1) +#define ISR_DECODER_FAILURE 0x00000040 +#define ISR_DECODER_ERROR 0x00000008 + +/* time-out for NAND chip / controller loops, in us */ +#define LPC32X_NAND_TIMEOUT 5000 + +/* + * There is a single instance of the NAND MLC controller + */ + +static struct lpc32xx_nand_mlc_registers __iomem *lpc32xx_nand_mlc_registers + = (struct lpc32xx_nand_mlc_registers __iomem *)MLC_NAND_BASE; + +#define clkdiv(v, w, o) (((1+(clk/v)) & w) << o) + +/** + * OOB data in each small page are 6 'free' then 10 ECC bytes. + * To make things easier, when reading large pages, the four pages' + * 'free' OOB bytes are grouped in the first 24 bytes of the OOB buffer, + * while the the four ECC bytes are groupe in its last 40 bytes. + * + * The struct below represents how free vs ecc oob bytes are stored + * in the buffer. + * + * Note: the OOB bytes contain the bad block marker at offsets 0 and 1. + */ + +struct lpc32xx_oob { + struct { + uint8_t free_oob_bytes[6]; + } free[4]; + struct { + uint8_t ecc_oob_bytes[10]; + } ecc[4]; +}; + +/* + * Initialize the controller + */ + +static void lpc32xx_nand_init(void) +{ + unsigned int clk; + + /* Configure controller for no software write protection, x8 bus + width, large block device, and 4 address words */ + + /* unlock controller registers with magic key */ + writel(LOCK_PR_UNLOCK_KEY, + &lpc32xx_nand_mlc_registers->lock_pr); + + /* enable large blocks and large NANDs */ + writel(ICR_LARGE_BLOCKS | ICR_ADDR4, + &lpc32xx_nand_mlc_registers->icr); + + /* Make sure MLC interrupts are disabled */ + writel(0, &lpc32xx_nand_mlc_registers->irq_mr); + + /* Normal chip enable operation */ + writel(CEH_NORMAL_CE, + &lpc32xx_nand_mlc_registers->ceh); + + /* Setup NAND timing */ + clk = get_hclk_clk_rate(); + + writel( + clkdiv(CONFIG_LPC32XX_NAND_MLC_TCEA_DELAY, 0x03, 24) | + clkdiv(CONFIG_LPC32XX_NAND_MLC_BUSY_DELAY, 0x1F, 19) | + clkdiv(CONFIG_LPC32XX_NAND_MLC_NAND_TA, 0x07, 16) | + clkdiv(CONFIG_LPC32XX_NAND_MLC_RD_HIGH, 0x0F, 12) | + clkdiv(CONFIG_LPC32XX_NAND_MLC_RD_LOW, 0x0F, 8) | + clkdiv(CONFIG_LPC32XX_NAND_MLC_WR_HIGH, 0x0F, 4) | + clkdiv(CONFIG_LPC32XX_NAND_MLC_WR_LOW, 0x0F, 0), + &lpc32xx_nand_mlc_registers->time_reg); +} + +#if !defined(CONFIG_SPL_BUILD) + +/** + * lpc32xx_cmd_ctrl - write command to either cmd or data register + */ + +static void lpc32xx_cmd_ctrl(struct mtd_info *mtd, int cmd, + unsigned int ctrl) +{ + if (cmd == NAND_CMD_NONE) + return; + + if (ctrl & NAND_CLE) + writeb(cmd & 0Xff, &lpc32xx_nand_mlc_registers->cmd); + else if (ctrl & NAND_ALE) + writeb(cmd & 0Xff, &lpc32xx_nand_mlc_registers->addr); +} + +/** + * lpc32xx_read_byte - read a byte from the NAND + * @mtd: MTD device structure + */ + +static uint8_t lpc32xx_read_byte(struct mtd_info *mtd) +{ + return readb(&lpc32xx_nand_mlc_registers->data); +} + +/** + * lpc32xx_dev_ready - test if NAND device (actually controller) is ready + * @mtd: MTD device structure + * @mode: mode to set the ECC HW to. + */ + +static int lpc32xx_dev_ready(struct mtd_info *mtd) +{ + /* means *controller* ready for us */ + int status = readl(&lpc32xx_nand_mlc_registers->isr); + return status & ISR_CONTROLLER_READY; +} + +/** + * ECC layout -- this is needed whatever ECC mode we are using. + * In a 2KB (4*512B) page, R/S codes occupy 40 (4*10) bytes. + * To make U-Boot's life easier, we pack 'useable' OOB at the + * front and R/S ECC at the back. + */ + +static struct nand_ecclayout lpc32xx_largepage_ecclayout = { + .eccbytes = 40, + .eccpos = {24, 25, 26, 27, 28, 29, 30, 31, 32, 33, + 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, + 44, 45, 46, 47, 48, 48, 50, 51, 52, 53, + 54, 55, 56, 57, 58, 59, 60, 61, 62, 63, + }, + .oobfree = { + /* bytes 0 and 1 are used for the bad block marker */ + { + .offset = 2, + .length = 22 + }, + } +}; + +/** + * lpc32xx_read_page_hwecc - read in- and out-of-band data with ECC + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: buffer to store read data + * @oob_required: caller requires OOB data read to chip->oob_poi + * @page: page number to read + * + * Use large block Auto Decode Read Mode(1) as described in User Manual + * section 8.6.2.1. + * + * The initial Read Mode and Read Start commands are sent by the caller. + * + * ECC will be false if out-of-band data has been updated since in-band + * data was initially written. + */ + +static int lpc32xx_read_page_hwecc(struct mtd_info *mtd, + struct nand_chip *chip, uint8_t *buf, int oob_required, + int page) +{ + unsigned int i, status, timeout, err, max_bitflips = 0; + struct lpc32xx_oob *oob = (struct lpc32xx_oob *)chip->oob_poi; + + /* go through all four small pages */ + for (i = 0; i < 4; i++) { + /* start auto decode (reads 528 NAND bytes) */ + writel(0, &lpc32xx_nand_mlc_registers->ecc_auto_dec_reg); + /* wait for controller to return to ready state */ + for (timeout = LPC32X_NAND_TIMEOUT; timeout; timeout--) { + status = readl(&lpc32xx_nand_mlc_registers->isr); + if (status & ISR_CONTROLLER_READY) + break; + udelay(1); + } + /* if decoder failed, return failure */ + if (status & ISR_DECODER_FAILURE) + return -1; + /* keep count of maximum bitflips performed */ + if (status & ISR_DECODER_ERROR) { + err = ISR_DECODER_ERRORS(status); + if (err > max_bitflips) + max_bitflips = err; + } + /* copy first 512 bytes into buffer */ + memcpy(buf+512*i, lpc32xx_nand_mlc_registers->buff, 512); + /* copy next 6 bytes at front of OOB buffer */ + memcpy(&oob->free[i], lpc32xx_nand_mlc_registers->buff, 6); + /* copy last 10 bytes (R/S ECC) at back of OOB buffer */ + memcpy(&oob->ecc[i], lpc32xx_nand_mlc_registers->buff, 10); + } + return max_bitflips; +} + +/** + * lpc32xx_read_page_raw - read raw (in-band, out-of-band and ECC) data + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: buffer to store read data + * @oob_required: caller requires OOB data read to chip->oob_poi + * @page: page number to read + * + * Read NAND directly; can read pages with invalid ECC. + */ + +static int lpc32xx_read_page_raw(struct mtd_info *mtd, + struct nand_chip *chip, uint8_t *buf, int oob_required, + int page) +{ + unsigned int i, status, timeout; + struct lpc32xx_oob *oob = (struct lpc32xx_oob *)chip->oob_poi; + + /* when we get here we've already had the Read Mode(1) */ + + /* go through all four small pages */ + for (i = 0; i < 4; i++) { + /* wait for NAND to return to ready state */ + for (timeout = LPC32X_NAND_TIMEOUT; timeout; timeout--) { + status = readl(&lpc32xx_nand_mlc_registers->isr); + if (status & ISR_NAND_READY) + break; + udelay(1); + } + /* if NAND stalled, return failure */ + if (!(status & ISR_NAND_READY)) + return -1; + /* copy first 512 bytes into buffer */ + memcpy(buf+512*i, lpc32xx_nand_mlc_registers->data, 512); + /* copy next 6 bytes at front of OOB buffer */ + memcpy(&oob->free[i], lpc32xx_nand_mlc_registers->data, 6); + /* copy last 10 bytes (R/S ECC) at back of OOB buffer */ + memcpy(&oob->ecc[i], lpc32xx_nand_mlc_registers->data, 10); + } + return 0; +} + +/** + * lpc32xx_read_oob - read out-of-band data + * @mtd: mtd info structure + * @chip: nand chip info structure + * @page: page number to read + * + * Read out-of-band data. User Manual section 8.6.4 suggests using Read + * Mode(3) which the controller will turn into a Read Mode(1) internally + * but nand_base.c will turn Mode(3) into Mode(0), so let's use Mode(0) + * directly. + * + * ECC covers in- and out-of-band data and was written when out-of-band + * data was blank. Therefore, if the out-of-band being read here is not + * blank, then the ECC will be false and the read will return bitflips, + * even in case of ECC failure where we will return 5 bitflips. The + * caller should be prepared to handle this. + */ + +static int lpc32xx_read_oob(struct mtd_info *mtd, struct nand_chip *chip, + int page) +{ + unsigned int i, status, timeout, err, max_bitflips = 0; + struct lpc32xx_oob *oob = (struct lpc32xx_oob *)chip->oob_poi; + + /* No command was sent before calling read_oob() so send one */ + + chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page); + + /* go through all four small pages */ + for (i = 0; i < 4; i++) { + /* start auto decode (reads 528 NAND bytes) */ + writel(0, &lpc32xx_nand_mlc_registers->ecc_auto_dec_reg); + /* wait for controller to return to ready state */ + for (timeout = LPC32X_NAND_TIMEOUT; timeout; timeout--) { + status = readl(&lpc32xx_nand_mlc_registers->isr); + if (status & ISR_CONTROLLER_READY) + break; + udelay(1); + } + /* if decoder failure, count 'one too many' bitflips */ + if (status & ISR_DECODER_FAILURE) + max_bitflips = 5; + /* keep count of maximum bitflips performed */ + if (status & ISR_DECODER_ERROR) { + err = ISR_DECODER_ERRORS(status); + if (err > max_bitflips) + max_bitflips = err; + } + /* set read pointer to OOB area */ + writel(0, &lpc32xx_nand_mlc_registers->robp); + /* copy next 6 bytes at front of OOB buffer */ + memcpy(&oob->free[i], lpc32xx_nand_mlc_registers->buff, 6); + /* copy next 10 bytes (R/S ECC) at back of OOB buffer */ + memcpy(&oob->ecc[i], lpc32xx_nand_mlc_registers->buff, 10); + } + return max_bitflips; +} + +/** + * lpc32xx_write_page_hwecc - write in- and out-of-band data with ECC + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: data buffer + * @oob_required: must write chip->oob_poi to OOB + * + * Use large block Auto Encode as per User Manual section 8.6.4. + * + * The initial Write Serial Input and final Auto Program commands are + * sent by the caller. + */ + +static int lpc32xx_write_page_hwecc(struct mtd_info *mtd, + struct nand_chip *chip, const uint8_t *buf, int oob_required) +{ + unsigned int i, status, timeout; + struct lpc32xx_oob *oob = (struct lpc32xx_oob *)chip->oob_poi; + + /* when we get here we've already had the SEQIN */ + for (i = 0; i < 4; i++) { + /* start encode (expects 518 writes to buff) */ + writel(0, &lpc32xx_nand_mlc_registers->ecc_enc_reg); + /* copy first 512 bytes from buffer */ + memcpy(&lpc32xx_nand_mlc_registers->buff, buf+512*i, 512); + /* copy next 6 bytes from OOB buffer -- excluding ECC */ + memcpy(&lpc32xx_nand_mlc_registers->buff, &oob->free[i], 6); + /* wait for ECC to return to ready state */ + for (timeout = LPC32X_NAND_TIMEOUT; timeout; timeout--) { + status = readl(&lpc32xx_nand_mlc_registers->isr); + if (status & ISR_ECC_READY) + break; + udelay(1); + } + /* if ECC stalled, return failure */ + if (!(status & ISR_ECC_READY)) + return -1; + /* Trigger auto encode (writes 528 bytes to NAND) */ + writel(0, &lpc32xx_nand_mlc_registers->ecc_auto_enc_reg); + /* wait for controller to return to ready state */ + for (timeout = LPC32X_NAND_TIMEOUT; timeout; timeout--) { + status = readl(&lpc32xx_nand_mlc_registers->isr); + if (status & ISR_CONTROLLER_READY) + break; + udelay(1); + } + /* if controller stalled, return error */ + if (!(status & ISR_CONTROLLER_READY)) + return -1; + } + return 0; +} + +/** + * lpc32xx_write_page_raw - write raw (in-band, out-of-band and ECC) data + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: buffer to store read data + * @oob_required: caller requires OOB data read to chip->oob_poi + * @page: page number to read + * + * Use large block write but without encode. + * + * The initial Write Serial Input and final Auto Program commands are + * sent by the caller. + * + * This function will write the full out-of-band data, including the + * ECC area. Therefore, it can write pages with valid *or* invalid ECC. + */ + +static int lpc32xx_write_page_raw(struct mtd_info *mtd, + struct nand_chip *chip, const uint8_t *buf, int oob_required) +{ + unsigned int i; + struct lpc32xx_oob *oob = (struct lpc32xx_oob *)chip->oob_poi; + + /* when we get here we've already had the Read Mode(1) */ + for (i = 0; i < 4; i++) { + /* copy first 512 bytes from buffer */ + memcpy(lpc32xx_nand_mlc_registers->buff, buf+512*i, 512); + /* copy next 6 bytes into OOB buffer -- excluding ECC */ + memcpy(lpc32xx_nand_mlc_registers->buff, &oob->free[i], 6); + /* copy next 10 bytes into OOB buffer -- that is 'ECC' */ + memcpy(lpc32xx_nand_mlc_registers->buff, &oob->ecc[i], 10); + } + return 0; +} + +/** + * lpc32xx_write_oob - write out-of-band data + * @mtd: mtd info structure + * @chip: nand chip info structure + * @page: page number to read + * + * Since ECC covers in- and out-of-band data, writing out-of-band data + * with ECC will render the page ECC wrong -- or, if the page was blank, + * then it will produce a good ECC but a later in-band data write will + * render it wrong. + * + * Therefore, do not compute or write any ECC, and always return success. + * + * This implies that we do four writes, since non-ECC out-of-band data + * are not contiguous in a large page. + */ + +static int lpc32xx_write_oob(struct mtd_info *mtd, struct nand_chip *chip, + int page) +{ + /* update oob on all 4 subpages in sequence */ + unsigned int i, status, timeout; + struct lpc32xx_oob *oob = (struct lpc32xx_oob *)chip->oob_poi; + + for (i = 0; i < 4; i++) { + /* start data input */ + chip->cmdfunc(mtd, NAND_CMD_SEQIN, 0x200+0x210*i, page); + /* copy 6 non-ECC out-of-band bytes directly into NAND */ + memcpy(lpc32xx_nand_mlc_registers->data, &oob->free[i], 6); + /* program page */ + chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); + /* wait for NAND to return to ready state */ + for (timeout = LPC32X_NAND_TIMEOUT; timeout; timeout--) { + status = readl(&lpc32xx_nand_mlc_registers->isr); + if (status & ISR_NAND_READY) + break; + udelay(1); + } + /* if NAND stalled, return error */ + if (!(status & ISR_NAND_READY)) + return -1; + } + return 0; +} + +/** + * lpc32xx_waitfunc - wait until a command is done + * @mtd: MTD device structure + * @chip: NAND chip structure + * + * Wait for controller and FLASH to both be ready. + */ + +static int lpc32xx_waitfunc(struct mtd_info *mtd, struct nand_chip *chip) +{ + int status; + unsigned int timeout; + /* wait until both controller and NAND are ready */ + for (timeout = LPC32X_NAND_TIMEOUT; timeout; timeout--) { + status = readl(&lpc32xx_nand_mlc_registers->isr); + if ((status & (ISR_CONTROLLER_READY || ISR_NAND_READY)) + == (ISR_CONTROLLER_READY || ISR_NAND_READY)) + break; + udelay(1); + } + /* if controller or NAND stalled, return error */ + if ((status & (ISR_CONTROLLER_READY || ISR_NAND_READY)) + != (ISR_CONTROLLER_READY || ISR_NAND_READY)) + return -1; + /* write NAND status command */ + writel(NAND_CMD_STATUS, &lpc32xx_nand_mlc_registers->cmd); + /* read back status and return it */ + return readb(&lpc32xx_nand_mlc_registers->data); +} + +/* + * We are self-initializing, so we need our own chip struct + */ + +static struct nand_chip lpc32xx_chip; + +/* + * Initialize the controller + */ + +void board_nand_init(void) +{ + /* we have only one device anyway */ + struct mtd_info *mtd = &nand_info[0]; + /* chip is struct nand_chip, and is now provided by the driver. */ + mtd->priv = &lpc32xx_chip; + /* to store return status in case we need to print it */ + int ret; + + /* Set all BOARDSPECIFIC (actually core-specific) fields */ + + lpc32xx_chip.IO_ADDR_R = &lpc32xx_nand_mlc_registers->buff; + lpc32xx_chip.IO_ADDR_W = &lpc32xx_nand_mlc_registers->buff; + lpc32xx_chip.cmd_ctrl = lpc32xx_cmd_ctrl; + /* do not set init_size: nand_base.c will read sizes from chip */ + lpc32xx_chip.dev_ready = lpc32xx_dev_ready; + /* do not set setup_read_retry: this is NAND-chip-specific */ + /* do not set chip_delay: we have dev_ready defined. */ + lpc32xx_chip.options |= NAND_NO_SUBPAGE_WRITE; + + /* Set needed ECC fields */ + + lpc32xx_chip.ecc.mode = NAND_ECC_HW; + lpc32xx_chip.ecc.layout = &lpc32xx_largepage_ecclayout; + lpc32xx_chip.ecc.size = 512; + lpc32xx_chip.ecc.bytes = 10; + lpc32xx_chip.ecc.strength = 4; + lpc32xx_chip.ecc.read_page = lpc32xx_read_page_hwecc; + lpc32xx_chip.ecc.read_page_raw = lpc32xx_read_page_raw; + lpc32xx_chip.ecc.write_page = lpc32xx_write_page_hwecc; + lpc32xx_chip.ecc.write_page_raw = lpc32xx_write_page_raw; + lpc32xx_chip.ecc.read_oob = lpc32xx_read_oob; + lpc32xx_chip.ecc.write_oob = lpc32xx_write_oob; + lpc32xx_chip.waitfunc = lpc32xx_waitfunc; + + lpc32xx_chip.read_byte = lpc32xx_read_byte; /* FIXME: NEEDED? */ + + /* BBT options: read from last two pages */ + lpc32xx_chip.bbt_options |= NAND_BBT_USE_FLASH | NAND_BBT_LASTBLOCK + | NAND_BBT_SCANLASTPAGE | NAND_BBT_SCAN2NDPAGE + | NAND_BBT_WRITE; + + /* Initialize NAND interface */ + lpc32xx_nand_init(); + + /* identify chip */ + ret = nand_scan_ident(mtd, CONFIG_SYS_MAX_NAND_CHIPS, NULL); + if (ret) { + error("nand_scan_ident returned %i", ret); + return; + } + + /* finish scanning the chip */ + ret = nand_scan_tail(mtd); + if (ret) { + error("nand_scan_tail returned %i", ret); + return; + } + + /* chip is good, register it */ + ret = nand_register(0); + if (ret) + error("nand_register returned %i", ret); +} + +#else /* defined(CONFIG_SPL_BUILD) */ + +void nand_init(void) +{ + /* enable NAND controller */ + lpc32xx_mlc_nand_init(); + /* initialize NAND controller */ + lpc32xx_nand_init(); +} + +void nand_deselect(void) +{ + /* nothing to do, but SPL requires this function */ +} + +static int read_single_page(uint8_t *dest, int page, + struct lpc32xx_oob *oob) +{ + int status, i, timeout, err, max_bitflips = 0; + + /* enter read mode */ + writel(NAND_CMD_READ0, &lpc32xx_nand_mlc_registers->cmd); + /* send column (lsb then MSB) and page (lsb to MSB) */ + writel(0, &lpc32xx_nand_mlc_registers->addr); + writel(0, &lpc32xx_nand_mlc_registers->addr); + writel(page & 0xff, &lpc32xx_nand_mlc_registers->addr); + writel((page>>8) & 0xff, &lpc32xx_nand_mlc_registers->addr); + writel((page>>16) & 0xff, &lpc32xx_nand_mlc_registers->addr); + /* start reading */ + writel(NAND_CMD_READSTART, &lpc32xx_nand_mlc_registers->cmd); + + /* large page auto decode read */ + for (i = 0; i < 4; i++) { + /* start auto decode (reads 528 NAND bytes) */ + writel(0, &lpc32xx_nand_mlc_registers->ecc_auto_dec_reg); + /* wait for controller to return to ready state */ + for (timeout = LPC32X_NAND_TIMEOUT; timeout; timeout--) { + status = readl(&lpc32xx_nand_mlc_registers->isr); + if (status & ISR_CONTROLLER_READY) + break; + udelay(1); + } + /* if controller stalled, return error */ + if (!(status & ISR_CONTROLLER_READY)) + return -1; + /* if decoder failure, return error */ + if (status & ISR_DECODER_FAILURE) + return -1; + /* keep count of maximum bitflips performed */ + if (status & ISR_DECODER_ERROR) { + err = ISR_DECODER_ERRORS(status); + if (err > max_bitflips) + max_bitflips = err; + } + /* copy first 512 bytes into buffer */ + memcpy(dest+i*512, lpc32xx_nand_mlc_registers->buff, 512); + /* copy next 6 bytes bytes into OOB buffer */ + memcpy(&oob->free[i], lpc32xx_nand_mlc_registers->buff, 6); + } + return max_bitflips; +} + +/* + * Load U-Boot signed image. + * This loads an image from NAND, skipping bad blocks. + * A block is declared bad if at least one of its readable pages has + * a bad block marker in its OOB at position 0. + * If all pages ion a block are unreadable, the block is considered + * bad (i.e., assumed not to be part of the image) and skipped. + * + * IMPORTANT NOTE: + * + * If the first block of the image is fully unreadable, it will be + * ignored and skipped as if it had been marked bad. If it was not + * actually marked bad at the time of writing the image, the resulting + * image loaded will lack a header and magic number. It could thus be + * considered as a raw, headerless, image and SPL might erroneously + * jump into it. + * + * In order to avoid this risk, LPC32XX-based boards which use this + * driver MUST define CONFIG_SPL_PANIC_ON_RAW_IMAGE. + */ + +#define BYTES_PER_PAGE 2048 +#define PAGES_PER_BLOCK 64 +#define BYTES_PER_BLOCK (BYTES_PER_PAGE * PAGES_PER_BLOCK) +#define PAGES_PER_CHIP_MAX 524288 + +int nand_spl_load_image(uint32_t offs, unsigned int size, void *dst) +{ + int bytes_left = size; + int pages_left = DIV_ROUND_UP(size, BYTES_PER_PAGE); + int blocks_left = DIV_ROUND_UP(size, BYTES_PER_BLOCK); + int block = 0; + int page = offs / BYTES_PER_PAGE; + /* perform reads block by block */ + while (blocks_left) { + /* compute first page number to read */ + void *block_page_dst = dst; + /* read at most one block, possibly less */ + int block_bytes_left = bytes_left; + if (block_bytes_left > BYTES_PER_BLOCK) + block_bytes_left = BYTES_PER_BLOCK; + /* keep track of good, failed, and "bad" pages */ + int block_pages_good = 0; + int block_pages_bad = 0; + int block_pages_err = 0; + /* we shall read a full block of pages, maybe less */ + int block_pages_left = pages_left; + if (block_pages_left > PAGES_PER_BLOCK) + block_pages_left = PAGES_PER_BLOCK; + int block_pages = block_pages_left; + int block_page = page; + /* while pages are left and the block is not known as bad */ + while ((block_pages > 0) && (block_pages_bad == 0)) { + /* we will read OOB, too, for bad block markers */ + struct lpc32xx_oob oob; + /* read page */ + int res = read_single_page(block_page_dst, block_page, + &oob); + /* count readable pages */ + if (res >= 0) { + /* this page is good */ + block_pages_good++; + /* this page is bad */ + if ((oob.free[0].free_oob_bytes[0] != 0xff) + | (oob.free[0].free_oob_bytes[1] != 0xff)) + block_pages_bad++; + } else + /* count errors */ + block_pages_err++; + /* we're done with this page */ + block_page++; + block_page_dst += BYTES_PER_PAGE; + if (block_pages) + block_pages--; + } + /* a fully unreadable block is considered bad */ + if (block_pages_good == 0) + block_pages_bad = block_pages_err; + /* errors are fatal only in good blocks */ + if ((block_pages_err > 0) && (block_pages_bad == 0)) + return -1; + /* we keep reads only of good blocks */ + if (block_pages_bad == 0) { + dst += block_bytes_left; + bytes_left -= block_bytes_left; + pages_left -= block_pages_left; + blocks_left--; + } + /* good or bad, we're done with this block */ + block++; + page += PAGES_PER_BLOCK; + } + + /* report success */ + return 0; +} + +#endif /* CONFIG_SPL_BUILD */ diff --git a/drivers/net/Makefile b/drivers/net/Makefile index 3ff86b7..5a5269a 100644 --- a/drivers/net/Makefile +++ b/drivers/net/Makefile @@ -35,6 +35,7 @@ obj-$(CONFIG_GRETH) += greth.o obj-$(CONFIG_DRIVER_TI_KEYSTONE_NET) += keystone_net.o obj-$(CONFIG_KS8851_MLL) += ks8851_mll.o obj-$(CONFIG_LAN91C96) += lan91c96.o +obj-$(CONFIG_LPC32XX_ETH) += lpc32xx_eth.o obj-$(CONFIG_MACB) += macb.o obj-$(CONFIG_MCFFEC) += mcffec.o mcfmii.o obj-$(CONFIG_MPC5xxx_FEC) += mpc5xxx_fec.o diff --git a/drivers/net/lpc32xx_eth.c b/drivers/net/lpc32xx_eth.c new file mode 100644 index 0000000..fcadf0c --- /dev/null +++ b/drivers/net/lpc32xx_eth.c @@ -0,0 +1,637 @@ +/* + * LPC32xx Ethernet MAC interface driver + * + * (C) Copyright 2014 DENX Software Engineering GmbH + * Written-by: Albert ARIBAUD - 3ADEV <albert.aribaud@3adev.fr> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <net.h> +#include <malloc.h> +#include <miiphy.h> +#include <asm/io.h> +#include <asm/errno.h> +#include <asm/types.h> +#include <asm/system.h> +#include <asm/byteorder.h> +#include <asm/arch/cpu.h> +#include <asm/arch/config.h> + +/* + * Notes: + * + * 1. Unless specified otherwise, all references to tables or paragraphs + * are to UM10326, "LPC32x0 and LPC32x0/01 User manual". + * + * 2. Only bitfield masks/values which are actually used by the driver + * are defined. + */ + +/* a single RX descriptor. The controller has an array of these */ +struct lpc32xx_eth_rxdesc { + u32 packet; /* Receive packet pointer */ + u32 control; /* Descriptor command status */ +}; + +#define LPC32XX_ETH_RX_DESC_SIZE (sizeof(struct lpc32xx_eth_rxdesc)) + +/* RX control bitfields/masks (see Table 330) */ +#define LPC32XX_ETH_RX_CTRL_SIZE_MASK 0x000007FF +#define LPC32XX_ETH_RX_CTRL_UNUSED 0x7FFFF800 +#define LPC32XX_ETH_RX_CTRL_INTERRUPT 0x80000000 + +/* a single RX status. The controller has an array of these */ +struct lpc32xx_eth_rxstat { + u32 statusinfo; /* Transmit Descriptor status */ + u32 statushashcrc; /* Transmit Descriptor CRCs */ +}; + +#define LPC32XX_ETH_RX_STAT_SIZE (sizeof(struct lpc32xx_eth_rxstat)) + +/* RX statusinfo bitfields/masks (see Table 333) */ +#define RX_STAT_RXSIZE 0x000007FF +/* Helper: OR of all errors except RANGE */ +#define RX_STAT_ERRORS 0x1B800000 + +/* a single TX descriptor. The controller has an array of these */ +struct lpc32xx_eth_txdesc { + u32 packet; /* Transmit packet pointer */ + u32 control; /* Descriptor control */ +}; + +#define LPC32XX_ETH_TX_DESC_SIZE (sizeof(struct lpc32xx_eth_txdesc)) + +/* TX control bitfields/masks (see Table 335) */ +#define TX_CTRL_TXSIZE 0x000007FF +#define TX_CTRL_LAST 0x40000000 + +/* a single TX status. The controller has an array of these */ +struct lpc32xx_eth_txstat { + u32 statusinfo; /* Transmit Descriptor status */ +}; + +#define LPC32XX_ETH_TX_STAT_SIZE (sizeof(struct lpc32xx_eth_txstat)) + +/* Ethernet MAC interface registers (see Table 283) */ +struct lpc32xx_eth_registers { + /* MAC registers - 0x3106_0000 to 0x3106_01FC */ + u32 mac1; /* MAC configuration register 1 */ + u32 mac2; /* MAC configuration register 2 */ + u32 ipgt; /* Back-to-back Inter-Packet Gap reg. */ + u32 ipgr; /* Non-back-to-back IPG register */ + u32 clrt; /* Collision Window / Retry register */ + u32 maxf; /* Maximum Frame register */ + u32 supp; /* Phy Support register */ + u32 test; + u32 mcfg; /* MII management configuration reg. */ + u32 mcmd; /* MII management command register */ + u32 madr; /* MII management address register */ + u32 mwtd; /* MII management wite data register */ + u32 mrdd; /* MII management read data register */ + u32 mind; /* MII management indicators register */ + u32 reserved1[2]; + u32 sa0; /* Station address register 0 */ + u32 sa1; /* Station address register 1 */ + u32 sa2; /* Station address register 2 */ + u32 reserved2[45]; + /* Control registers */ + u32 command; + u32 status; + u32 rxdescriptor; + u32 rxstatus; + u32 rxdescriptornumber; /* actually, number MINUS ONE */ + u32 rxproduceindex; /* head of rx desc fifo */ + u32 rxconsumeindex; /* tail of rx desc fifo */ + u32 txdescriptor; + u32 txstatus; + u32 txdescriptornumber; /* actually, number MINUS ONE */ + u32 txproduceindex; /* head of rx desc fifo */ + u32 txconsumeindex; /* tail of rx desc fifo */ + u32 reserved3[10]; + u32 tsv0; /* Transmit status vector register 0 */ + u32 tsv1; /* Transmit status vector register 1 */ + u32 rsv; /* Receive status vector register */ + u32 reserved4[3]; + u32 flowcontrolcounter; + u32 flowcontrolstatus; + u32 reserved5[34]; + /* RX filter registers - 0x3106_0200 to 0x3106_0FDC */ + u32 rxfilterctrl; + u32 rxfilterwolstatus; + u32 rxfilterwolclear; + u32 reserved6; + u32 hashfilterl; + u32 hashfilterh; + u32 reserved7[882]; + /* Module control registers - 0x3106_0FE0 to 0x3106_0FF8 */ + u32 intstatus; /* Interrupt status register */ + u32 intenable; + u32 intclear; + u32 intset; + u32 reserved8; + u32 powerdown; + u32 reserved9; +}; + +/* MAC1 register bitfields/masks and offsets (see Table 283) */ +#define MAC1_RECV_ENABLE 0x00000001 +#define MAC1_PASS_ALL_RX_FRAMES 0x00000002 +#define MAC1_SOFT_RESET 0x00008000 +/* Helper: general reset */ +#define MAC1_RESETS 0x0000CF00 + +/* MAC2 register bitfields/masks and offsets (see Table 284) */ +#define MAC2_FULL_DUPLEX 0x00000001 +#define MAC2_CRC_ENABLE 0x00000010 +#define MAC2_PAD_CRC_ENABLE 0x00000020 + +/* SUPP register bitfields/masks and offsets (see Table 290) */ +#define SUPP_SPEED 0x00000100 + +/* MCFG register bitfields/masks and offsets (see Table 292) */ +#define MCFG_CLOCK_SELECT_MASK 0x0000001C +/* divide clock by 28 (see Table 293) */ +#define MCFG_CLOCK_SELECT_DIV28 0x0000001C + +/* MADR register bitfields/masks and offsets (see Table 295) */ +#define MADR_REG_MASK 0x0000001F +#define MADR_PHY_MASK 0x00001F00 +#define MADR_REG_OFFSET 0 +#define MADR_PHY_OFFSET 8 + +/* MIND register bitfields/masks (see Table 298) */ +#define MIND_BUSY 0x00000001 + +/* COMMAND register bitfields/masks and offsets (see Table 283) */ +#define COMMAND_RXENABLE 0x00000001 +#define COMMAND_TXENABLE 0x00000002 +#define COMMAND_PASSRUNTFRAME 0x00000040 +#define COMMAND_FULL_DUPLEX 0x00000400 +/* Helper: general reset */ +#define COMMAND_RESETS 0x0000001C + +/* STATUS register bitfields/masks and offsets (see Table 283) */ +#define STATUS_RXSTATUS 0x00000001 +#define STATUS_TXSTATUS 0x00000002 + +/* RXFILTERCTRL register bitfields/masks (see Table 319) */ +#define RXFILTERCTRL_ACCEPTBROADCAST 0x00000002 +#define RXFILTERCTRL_ACCEPTPERFECT 0x00000020 + +/* Buffers and descriptors */ + +#define ATTRS(n) __aligned(n) + +#define TX_BUF_COUNT 4 +#define RX_BUF_COUNT 4 + +struct lpc32xx_eth_buffers { + ATTRS(4) struct lpc32xx_eth_txdesc tx_desc[TX_BUF_COUNT]; + ATTRS(4) struct lpc32xx_eth_txstat tx_stat[TX_BUF_COUNT]; + ATTRS(PKTALIGN) u8 tx_buf[TX_BUF_COUNT*PKTSIZE_ALIGN]; + ATTRS(4) struct lpc32xx_eth_rxdesc rx_desc[RX_BUF_COUNT]; + ATTRS(8) struct lpc32xx_eth_rxstat rx_stat[RX_BUF_COUNT]; + ATTRS(PKTALIGN) u8 rx_buf[RX_BUF_COUNT*PKTSIZE_ALIGN]; +}; + +/* port device data struct */ +struct lpc32xx_eth_device { + struct eth_device dev; + struct lpc32xx_eth_registers *regs; + struct lpc32xx_eth_buffers *bufs; +}; + +#define LPC32XX_ETH_DEVICE_SIZE (sizeof(struct lpc32xx_eth_device)) + +/* generic macros */ +#define to_lpc32xx_eth(_d) container_of(_d, struct lpc32xx_eth_device, dev) + +/* timeout for MII polling */ +#define MII_TIMEOUT 10000000 + +/* limits for PHY and register addresses */ +#define MII_MAX_REG (MADR_REG_MASK >> MADR_REG_OFFSET) + +#define MII_MAX_PHY (MADR_PHY_MASK >> MADR_PHY_OFFSET) + +DECLARE_GLOBAL_DATA_PTR; + +#if defined(CONFIG_PHYLIB) || defined(CONFIG_MII) || defined(CONFIG_CMD_MII) +/* + * mii_reg_read - miiphy_read callback function. + * + * Returns 16bit phy register value, or 0xffff on error + */ +static int mii_reg_read(const char *devname, u8 phy_adr, u8 reg_ofs, u16 *data) +{ + struct eth_device *dev = eth_get_dev_by_name(devname); + struct lpc32xx_eth_device *dlpc32xx_eth = to_lpc32xx_eth(dev); + struct lpc32xx_eth_registers *regs = dlpc32xx_eth->regs; + u32 mind_reg; + u32 timeout; + + /* check parameters */ + if (phy_adr > MII_MAX_PHY) { + printf("%s:%u: Invalid PHY address %d\n", + __func__, __LINE__, phy_adr); + return -EFAULT; + } + if (reg_ofs > MII_MAX_REG) { + printf("%s:%u: Invalid register offset %d\n", + __func__, __LINE__, reg_ofs); + return -EFAULT; + } + + /* write the phy and reg addressse into the MII address reg */ + writel((phy_adr << MADR_PHY_OFFSET) | (reg_ofs << MADR_REG_OFFSET), + ®s->madr); + + /* write 1 to the MII command register to cause a read */ + writel(1, ®s->mcmd); + + /* wait till the MII is not busy */ + timeout = MII_TIMEOUT; + do { + /* read MII indicators register */ + mind_reg = readl(®s->mind); + if (--timeout == 0) + break; + } while (mind_reg & MIND_BUSY); + + /* write 0 to the MII command register to finish the read */ + writel(0, ®s->mcmd); + + if (timeout == 0) { + printf("%s:%u: MII busy timeout\n", __func__, __LINE__); + return -EFAULT; + } + + *data = (u16) readl(®s->mrdd); + + debug("%s:(adr %d, off %d) => %04x\n", __func__, phy_adr, + reg_ofs, *data); + + return 0; +} + +/* + * mii_reg_write - imiiphy_write callback function. + * + * Returns 0 if write succeed, -EINVAL on bad parameters + * -ETIME on timeout + */ +static int mii_reg_write(const char *devname, u8 phy_adr, u8 reg_ofs, u16 data) +{ + struct eth_device *dev = eth_get_dev_by_name(devname); + struct lpc32xx_eth_device *dlpc32xx_eth = to_lpc32xx_eth(dev); + struct lpc32xx_eth_registers *regs = dlpc32xx_eth->regs; + u32 mind_reg; + u32 timeout; + + /* check parameters */ + if (phy_adr > MII_MAX_PHY) { + printf("%s:%u: Invalid PHY address %d\n", + __func__, __LINE__, phy_adr); + return -EFAULT; + } + if (reg_ofs > MII_MAX_REG) { + printf("%s:%u: Invalid register offset %d\n", + __func__, __LINE__, reg_ofs); + return -EFAULT; + } + + /* wait till the MII is not busy */ + timeout = MII_TIMEOUT; + do { + /* read MII indicators register */ + mind_reg = readl(®s->mind); + if (--timeout == 0) + break; + } while (mind_reg & MIND_BUSY); + + if (timeout == 0) { + printf("%s:%u: MII busy timeout\n", __func__, + __LINE__); + return -EFAULT; + } + + /* write the phy and reg addressse into the MII address reg */ + writel((phy_adr << MADR_PHY_OFFSET) | (reg_ofs << MADR_REG_OFFSET), + ®s->madr); + + /* write data to the MII write register */ + writel(data, ®s->mwtd); + + /*debug("%s:(adr %d, off %d) <= %04x\n", __func__, phy_adr, + reg_ofs, data);*/ + + return 0; +} +#endif + +#if defined(CONFIG_PHYLIB) +int lpc32xx_eth_phy_read(struct mii_dev *bus, int phy_addr, int dev_addr, + int reg_addr) +{ + u16 data; + int ret; + ret = mii_reg_read(bus->name, phy_addr, reg_addr, &data); + if (ret) + return ret; + return data; +} + +int lpc32xx_eth_phy_write(struct mii_dev *bus, int phy_addr, int dev_addr, + int reg_addr, u16 data) +{ + return mii_reg_write(bus->name, phy_addr, reg_addr, data); +} +#endif + +/* + * Locate buffers in SRAM at 0x00001000 to avoid cache issues and + * maximize throughput. + */ + +#define LPC32XX_ETH_BUFS 0x00001000 + +static struct lpc32xx_eth_device lpc32xx_eth = { + .regs = (struct lpc32xx_eth_registers *)LPC32XX_ETH_BASE, + .bufs = (struct lpc32xx_eth_buffers *)LPC32XX_ETH_BUFS +}; + +#define TX_TIMEOUT 10000 + +static int lpc32xx_eth_send(struct eth_device *dev, void *dataptr, int datasize) +{ + struct lpc32xx_eth_device *lpc32xx_eth_device = + container_of(dev, struct lpc32xx_eth_device, dev); + struct lpc32xx_eth_registers *regs = lpc32xx_eth_device->regs; + struct lpc32xx_eth_buffers *bufs = lpc32xx_eth_device->bufs; + int timeout, tx_index; + + /* time out if transmit descriptor array remains full too long */ + timeout = TX_TIMEOUT; + while ((readl(®s->status) & STATUS_TXSTATUS) && + (readl(®s->txconsumeindex) + == readl(®s->txproduceindex))) { + if (timeout-- == 0) + return -1; + } + + /* determine next transmit packet index to use */ + tx_index = readl(®s->txproduceindex); + + /* set up transmit packet */ + writel((u32)dataptr, &bufs->tx_desc[tx_index].packet); + writel(TX_CTRL_LAST | ((datasize - 1) & TX_CTRL_TXSIZE), + &bufs->tx_desc[tx_index].control); + writel(0, &bufs->tx_stat[tx_index].statusinfo); + + /* pass transmit packet to DMA engine */ + tx_index = (tx_index + 1) % TX_BUF_COUNT; + writel(tx_index, ®s->txproduceindex); + + /* transmission succeeded */ + return 0; +} + +#define RX_TIMEOUT 1000000 + +static int lpc32xx_eth_recv(struct eth_device *dev) +{ + struct lpc32xx_eth_device *lpc32xx_eth_device = + container_of(dev, struct lpc32xx_eth_device, dev); + struct lpc32xx_eth_registers *regs = lpc32xx_eth_device->regs; + struct lpc32xx_eth_buffers *bufs = lpc32xx_eth_device->bufs; + int timeout, rx_index; + + /* time out if receive descriptor array remains empty too long */ + timeout = RX_TIMEOUT; + while (readl(®s->rxproduceindex) == readl(®s->rxconsumeindex)) { + if (timeout-- == 0) + return -1; + } + + /* determine next receive packet index to use */ + rx_index = readl(®s->rxconsumeindex); + + /* if data was valid, pass it on */ + if (!(bufs->rx_stat[rx_index].statusinfo & RX_STAT_ERRORS)) + NetReceive(&(bufs->rx_buf[rx_index*PKTSIZE_ALIGN]), + (bufs->rx_stat[rx_index].statusinfo + & RX_STAT_RXSIZE) + 1); + + /* pass receive slot back to DMA engine */ + rx_index = (rx_index + 1) % RX_BUF_COUNT; + writel(rx_index, ®s->rxconsumeindex); + + /* reception successful */ + return 0; +} + +static int lpc32xx_eth_write_hwaddr(struct eth_device *dev) +{ + struct lpc32xx_eth_device *lpc32xx_eth_device = + container_of(dev, struct lpc32xx_eth_device, dev); + struct lpc32xx_eth_registers *regs = lpc32xx_eth_device->regs; + + /* Save station address */ + writel((unsigned long) (dev->enetaddr[0] | + (dev->enetaddr[1] << 8)), ®s->sa2); + writel((unsigned long) (dev->enetaddr[2] | + (dev->enetaddr[3] << 8)), ®s->sa1); + writel((unsigned long) (dev->enetaddr[4] | + (dev->enetaddr[5] << 8)), ®s->sa0); + + return 0; +} + +static int lpc32xx_eth_init(struct eth_device *dev) +{ + struct lpc32xx_eth_device *lpc32xx_eth_device = + container_of(dev, struct lpc32xx_eth_device, dev); + struct lpc32xx_eth_registers *regs = lpc32xx_eth_device->regs; + struct lpc32xx_eth_buffers *bufs = lpc32xx_eth_device->bufs; + int index; + + /* Release SOFT reset to let MII talk to PHY */ + clrbits_le32(®s->mac1, MAC1_SOFT_RESET); + + /* Configure Full/Half Duplex mode */ + if (miiphy_duplex(dev->name, CONFIG_PHY_ADDR) == FULL) { + setbits_le32(®s->mac2, MAC2_FULL_DUPLEX); + setbits_le32(®s->command, COMMAND_FULL_DUPLEX); + writel(0x15, ®s->ipgt); + } else { + writel(0x12, ®s->ipgt); + } + + /* Configure 100MBit/10MBit mode */ + if (miiphy_speed(dev->name, CONFIG_PHY_ADDR) == _100BASET) + writel(SUPP_SPEED, ®s->supp); + else + writel(0, ®s->supp); + + /* Initial MAC initialization */ + writel(MAC1_PASS_ALL_RX_FRAMES, ®s->mac1); + writel(MAC2_PAD_CRC_ENABLE | MAC2_CRC_ENABLE, ®s->mac2); + writel(PKTSIZE_ALIGN, ®s->maxf); + + /* Retries: 15 (0xF). Collision window: 57 (0x37). */ + writel(0x370F, ®s->clrt); + + /* Set IP gap pt 2 to default 0x12 but pt 1 to non-default 0 */ + writel(0x0012, ®s->ipgr); + + /* pass runt (smaller than 64 bytes) frames */ + writel(COMMAND_PASSRUNTFRAME, ®s->command); + + /* Save station address */ + writel((unsigned long) (dev->enetaddr[0] | + (dev->enetaddr[1] << 8)), ®s->sa2); + writel((unsigned long) (dev->enetaddr[2] | + (dev->enetaddr[3] << 8)), ®s->sa1); + writel((unsigned long) (dev->enetaddr[4] | + (dev->enetaddr[5] << 8)), ®s->sa0); + + /* set up transmit buffers */ + for (index = 0; index < TX_BUF_COUNT; index++) { + bufs->tx_desc[index].control = 0; + bufs->tx_stat[index].statusinfo = 0; + } + writel((u32)(&bufs->tx_desc), (u32 *)®s->txdescriptor); + writel((u32)(&bufs->tx_stat), ®s->txstatus); + writel(TX_BUF_COUNT-1, ®s->txdescriptornumber); + + /* set up receive buffers */ + for (index = 0; index < RX_BUF_COUNT; index++) { + bufs->rx_desc[index].packet = + (u32) (bufs->rx_buf+index*PKTSIZE_ALIGN); + bufs->rx_desc[index].control = PKTSIZE_ALIGN - 1; + bufs->rx_stat[index].statusinfo = 0; + bufs->rx_stat[index].statushashcrc = 0; + } + writel((u32)(&bufs->rx_desc), ®s->rxdescriptor); + writel((u32)(&bufs->rx_stat), ®s->rxstatus); + writel(RX_BUF_COUNT-1, ®s->rxdescriptornumber); + + /* Enable broadcast and matching address packets */ + writel(RXFILTERCTRL_ACCEPTBROADCAST | + RXFILTERCTRL_ACCEPTPERFECT, ®s->rxfilterctrl); + + /* Clear and disable interrupts */ + writel(0xFFFF, ®s->intclear); + writel(0, ®s->intenable); + + /* Enable receive and transmit mode of MAC ethernet core */ + setbits_le32(®s->command, COMMAND_RXENABLE | COMMAND_TXENABLE); + setbits_le32(®s->mac1, MAC1_RECV_ENABLE); + + /* + * Perform a 'dummy' first send to work around Ethernet.1 + * erratum (see ES_LPC3250 rev. 9 dated 1 June 2011). + * Use zeroed "index" variable as the dummy. + */ + + index = 0; + lpc32xx_eth_send(dev, &index, 4); + + return 0; +} + +static int lpc32xx_eth_halt(struct eth_device *dev) +{ + struct lpc32xx_eth_device *lpc32xx_eth_device = + container_of(dev, struct lpc32xx_eth_device, dev); + struct lpc32xx_eth_registers *regs = lpc32xx_eth_device->regs; + + /* Reset all MAC logic */ + writel(MAC1_RESETS, ®s->mac1); + writel(COMMAND_RESETS, ®s->command); + /* Let reset condition settle */ + udelay(2000); + + return 0; +} + +#if defined(CONFIG_PHYLIB) +int lpc32xx_eth_phylib_init(struct eth_device *dev, int phyid) +{ + struct mii_dev *bus; + struct phy_device *phydev; + int ret; + + bus = mdio_alloc(); + if (!bus) { + printf("mdio_alloc failed\n"); + return -ENOMEM; + } + bus->read = lpc32xx_eth_phy_read; + bus->write = lpc32xx_eth_phy_write; + sprintf(bus->name, dev->name); + + ret = mdio_register(bus); + if (ret) { + printf("mdio_register failed\n"); + free(bus); + return -ENOMEM; + } + + phydev = phy_connect(bus, phyid, dev, PHY_INTERFACE_MODE_MII); + if (!phydev) { + printf("phy_connect failed\n"); + return -ENODEV; + } + + phy_config(phydev); + phy_startup(phydev); + + return 0; +} +#endif + +int lpc32xx_eth_initialize(bd_t *bis) +{ + struct eth_device *dev = &lpc32xx_eth.dev; + struct lpc32xx_eth_registers *regs = lpc32xx_eth.regs; + + /* + * Set RMII management clock rate. With HCLK at 104 MHz and + * a divider of 28, this will be 3.72 MHz. + */ + + writel(MCFG_CLOCK_SELECT_DIV28, ®s->mcfg); + + /* Reset all MAC logic */ + writel(MAC1_RESETS, ®s->mac1); + writel(COMMAND_RESETS, ®s->command); + + /* wait 10 ms for the whole I/F to reset */ + udelay(10000); + + /* must be less than sizeof(dev->name) */ + strcpy(dev->name, "eth0"); + + dev->init = (void *)lpc32xx_eth_init; + dev->halt = (void *)lpc32xx_eth_halt; + dev->send = (void *)lpc32xx_eth_send; + dev->recv = (void *)lpc32xx_eth_recv; + dev->write_hwaddr = (void *)lpc32xx_eth_write_hwaddr; + + /* Release SOFT reset to let MII talk to PHY */ + clrbits_le32(®s->mac1, MAC1_SOFT_RESET); + + /* register driver before talking to phy */ + eth_register(dev); + +#if defined(CONFIG_PHYLIB) + lpc32xx_eth_phylib_init(dev, 0); +#elif defined(CONFIG_MII) || defined(CONFIG_CMD_MII) + miiphy_register(dev->name, mii_reg_read, mii_reg_write); +#endif + + return 0; +} diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index edbd520..ce6f1cc 100644 --- a/drivers/spi/Makefile +++ b/drivers/spi/Makefile @@ -32,6 +32,7 @@ obj-$(CONFIG_EXYNOS_SPI) += exynos_spi.o obj-$(CONFIG_FTSSP010_SPI) += ftssp010_spi.o obj-$(CONFIG_ICH_SPI) += ich.o obj-$(CONFIG_KIRKWOOD_SPI) += kirkwood_spi.o +obj-$(CONFIG_LPC32XX_SSP) += lpc32xx_ssp.o obj-$(CONFIG_MPC52XX_SPI) += mpc52xx_spi.o obj-$(CONFIG_MPC8XXX_SPI) += mpc8xxx_spi.o obj-$(CONFIG_MXC_SPI) += mxc_spi.o diff --git a/drivers/spi/lpc32xx_ssp.c b/drivers/spi/lpc32xx_ssp.c new file mode 100644 index 0000000..c5b766c --- /dev/null +++ b/drivers/spi/lpc32xx_ssp.c @@ -0,0 +1,144 @@ +/* + * LPC32xx SSP interface (SPI mode) + * + * (C) Copyright 2014 DENX Software Engineering GmbH + * Written-by: Albert ARIBAUD <albert.aribaud@3adev.fr> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <linux/compat.h> +#include <asm/io.h> +#include <malloc.h> +#include <spi.h> +#include <asm/arch/clk.h> + +/* SSP chip registers */ +struct ssp_regs { + u32 cr0; + u32 cr1; + u32 data; + u32 sr; + u32 cpsr; + u32 imsc; + u32 ris; + u32 mis; + u32 icr; + u32 dmacr; +}; + +/* CR1 register defines */ +#define SSP_CR1_SSP_ENABLE 0x0002 + +/* SR register defines */ +#define SSP_SR_TNF 0x0002 +/* SSP status RX FIFO not empty bit */ +#define SSP_SR_RNE 0x0004 + +/* lpc32xx spi slave */ +struct lpc32xx_spi_slave { + struct spi_slave slave; + struct ssp_regs *regs; +}; + +static inline struct lpc32xx_spi_slave *to_lpc32xx_spi_slave( + struct spi_slave *slave) +{ + return container_of(slave, struct lpc32xx_spi_slave, slave); +} + +/* spi_init is called during boot when CONFIG_CMD_SPI is defined */ +void spi_init(void) +{ + /* + * nothing to do: clocking was enabled in lpc32xx_ssp_enable() + * and configuration will be done in spi_setup_slave() + */ +} + +/* the following is called in sequence by do_spi_xfer() */ + +struct spi_slave *spi_setup_slave(uint bus, uint cs, uint max_hz, uint mode) +{ + struct lpc32xx_spi_slave *lslave; + + /* we only set up SSP0 for now, so ignore bus */ + + if (mode & SPI_3WIRE) { + error("3-wire mode not supported"); + return NULL; + } + + if (mode & SPI_SLAVE) { + error("slave mode not supported\n"); + return NULL; + } + + if (mode & SPI_PREAMBLE) { + error("preamble byte skipping not supported\n"); + return NULL; + } + + lslave = spi_alloc_slave(struct lpc32xx_spi_slave, bus, cs); + if (!lslave) { + printf("SPI_error: Fail to allocate lpc32xx_spi_slave\n"); + return NULL; + } + + lslave->regs = (struct ssp_regs *)SSP0_BASE; + + /* + * 8 bit frame, SPI fmt, 500kbps -> clock divider is 26. + * Set SCR to 0 and CPSDVSR to 26. + */ + + writel(0x7, &lslave->regs->cr0); /* 8-bit chunks, SPI, 1 clk/bit */ + writel(26, &lslave->regs->cpsr); /* SSP clock = HCLK/26 = 500kbps */ + writel(0, &lslave->regs->imsc); /* do not raise any interrupts */ + writel(0, &lslave->regs->icr); /* clear any pending interrupt */ + writel(0, &lslave->regs->dmacr); /* do not do DMAs */ + writel(SSP_CR1_SSP_ENABLE, &lslave->regs->cr1); /* enable SSP0 */ + return &lslave->slave; +} + +void spi_free_slave(struct spi_slave *slave) +{ + struct lpc32xx_spi_slave *lslave = to_lpc32xx_spi_slave(slave); + + debug("(lpc32xx) spi_free_slave: 0x%08x\n", (u32)lslave); + free(lslave); +} + +int spi_claim_bus(struct spi_slave *slave) +{ + /* only one bus and slave so far, always available */ + return 0; +} + +int spi_xfer(struct spi_slave *slave, unsigned int bitlen, + const void *dout, void *din, unsigned long flags) +{ + struct lpc32xx_spi_slave *lslave = to_lpc32xx_spi_slave(slave); + int bytelen = bitlen >> 3; + int idx_out = 0; + int idx_in = 0; + int start_time; + + start_time = get_timer(0); + while ((idx_out < bytelen) || (idx_in < bytelen)) { + int status = readl(&lslave->regs->sr); + if ((idx_out < bytelen) && (status & SSP_SR_TNF)) + writel(((u8 *)dout)[idx_out++], &lslave->regs->data); + if ((idx_in < bytelen) && (status & status & SSP_SR_RNE)) + ((u8 *)din)[idx_in++] = readl(&lslave->regs->data); + if (get_timer(start_time) >= CONFIG_LPC32XX_SSP_TIMEOUT) + return -1; + } + return 0; +} + +void spi_release_bus(struct spi_slave *slave) +{ + /* do nothing */ +} |