diff options
Diffstat (limited to 'drivers')
| -rw-r--r-- | drivers/mmc/imx_esdhc.c | 56 |
1 files changed, 42 insertions, 14 deletions
diff --git a/drivers/mmc/imx_esdhc.c b/drivers/mmc/imx_esdhc.c index a5345cb..d086949 100644 --- a/drivers/mmc/imx_esdhc.c +++ b/drivers/mmc/imx_esdhc.c @@ -325,6 +325,11 @@ void set_sysctl(struct mmc *mmc, uint clock) pre_div >>= 1; div -= 1; + /* for USDHC, pre_div requires another shift in DDR mode */ + if (cfg->is_usdhc && (mmc->bus_width == EMMC_MODE_4BIT_DDR || + mmc->bus_width == EMMC_MODE_8BIT_DDR)) + pre_div >>= 1; + clk = (pre_div << 8) | (div << 4); #ifndef CONFIG_IMX_ESDHC_V1 @@ -353,6 +358,16 @@ static void esdhc_dll_setup(struct mmc *mmc) struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; struct fsl_esdhc *regs = (struct fsl_esdhc *)cfg->esdhc_base; uint dll_control; + u32 target_delay = ESDHC_DLL_TARGET_DEFAULT_VAL; + +/* For DDR mode operation, provide target delay parameter for each SD port. + * Use cfg->esdhc_base to distinguish the SD port #. The delay for each port + * is dependent on trace lengths for that particular port. If the following + * CONFIG is not defined, then the default target delay value will be used. + */ +#ifdef CONFIG_GET_DDR_TARGET_DELAY + target_delay = get_ddr_delay(cfg); +#endif /* For i.MX50 TO1, need to force slave override mode */ if (get_board_rev() == (0x50000 | CHIP_REV_1_0) || @@ -367,6 +382,11 @@ static void esdhc_dll_setup(struct mmc *mmc) writel(dll_control, ®s->dllctrl); } else { + + /* on USDHC, enable DLL only for clock > 25 MHz */ + if (cfg->is_usdhc && mmc->clock <= 25000000) + return; + /* Disable auto clock gating for PERCLK, HCLK, and IPGCLK */ writel(readl(®s->sysctl) | 0x7, ®s->sysctl); /* Stop SDCLK while delay line is calibrated */ @@ -375,16 +395,29 @@ static void esdhc_dll_setup(struct mmc *mmc) /* Reset DLL */ writel(readl(®s->dllctrl) | 0x2, ®s->dllctrl); + dll_control = 0; + /* Enable DLL */ - writel(readl(®s->dllctrl) | 0x1, ®s->dllctrl); + if (cfg->is_usdhc) + dll_control |= 0x01000001; + else + dll_control |= 0x00000001; - dll_control = readl(®s->dllctrl); + writel(dll_control, ®s->dllctrl); /* Set target delay */ - dll_control &= ~ESDHC_DLLCTRL_TARGET_MASK; - dll_control |= (ESDHC_DLL_TARGET_DEFAULT_VAL << - ESDHC_DLLCTRL_TARGET_SHIFT); - writel(dll_control, ®s->dllctrl); + if (cfg->is_usdhc) { + dll_control &= ~USDHC_DLLCTRL_TARGET_MASK; + dll_control |= (((target_delay & USDHC_DLL_LOW_MASK) << + USDHC_DLLCTRL_TARGET_LOW_SHIFT) | + ((target_delay >> USDHC_DLL_HIGH_SHIFT) << + USDHC_DLLCTRL_TARGET_HIGH_SHIFT)); + writel(dll_control, ®s->dllctrl); + } else { + dll_control &= ~ESDHC_DLLCTRL_TARGET_MASK; + dll_control |= (target_delay << ESDHC_DLLCTRL_TARGET_SHIFT); + writel(dll_control, ®s->dllctrl); + } /* Wait for slave lock */ while ((readl(®s->dllstatus) & ESDHC_DLLSTS_SLV_LOCK_MASK) != @@ -478,7 +511,7 @@ int fsl_esdhc_initialize(bd_t *bis, struct fsl_esdhc_cfg *cfg) { struct fsl_esdhc *regs; struct mmc *mmc; - u32 ver, caps; + u32 caps; if (!cfg) return -1; @@ -497,9 +530,7 @@ int fsl_esdhc_initialize(bd_t *bis, struct fsl_esdhc_cfg *cfg) enable_usdhc(); #endif - ver = (readl(®s->hostver) & ESDHC_HOSTVER_VVN_MASK) - >> ESDHC_HOSTVER_VVN_SHIFT; - if (SDHC_IS_USDHC(ver)) + if (cfg->is_usdhc) sprintf(mmc->name, "FSL_USDHC"); caps = readl(®s->hostcapblt); @@ -517,7 +548,7 @@ int fsl_esdhc_initialize(bd_t *bis, struct fsl_esdhc_cfg *cfg) * it is to be used in SDR mode only. Use eSDHC for DDR mode. */ #ifndef CONFIG_MX50_ENABLE_USDHC_SDR - if (ver >= ESDHC_HOSTVER_DDR_SUPPORT) + if (cfg->is_usdhc) mmc->host_caps |= EMMC_MODE_4BIT_DDR; #ifdef CONFIG_EMMC_DDR_PORT_DETECT @@ -525,9 +556,6 @@ int fsl_esdhc_initialize(bd_t *bis, struct fsl_esdhc_cfg *cfg) mmc->host_caps |= EMMC_MODE_4BIT_DDR; #endif - if (SDHC_IS_USDHC(ver)) - mmc->host_caps |= EMMC_MODE_4BIT_DDR; - #endif /* #ifndef CONFIG_MX50_ENABLE_USDHC_SDR */ mmc->f_min = 400000; |