diff options
Diffstat (limited to 'drivers/usb')
-rw-r--r-- | drivers/usb/host/ehci-mx6.c | 131 |
1 files changed, 91 insertions, 40 deletions
diff --git a/drivers/usb/host/ehci-mx6.c b/drivers/usb/host/ehci-mx6.c index 4d7da52..c0a557b 100644 --- a/drivers/usb/host/ehci-mx6.c +++ b/drivers/usb/host/ehci-mx6.c @@ -35,6 +35,7 @@ #define USBPHY_CTRL_CLKGATE 0x40000000 #define USBPHY_CTRL_ENUTMILEVEL3 0x00008000 #define USBPHY_CTRL_ENUTMILEVEL2 0x00004000 +#define USBPHY_CTRL_OTG_ID 0x08000000 #define ANADIG_USB2_CHRG_DETECT_EN_B 0x00100000 #define ANADIG_USB2_CHRG_DETECT_CHK_CHRG_B 0x00080000 @@ -49,52 +50,84 @@ #define UCTRL_OVER_CUR_DIS (1 << 7) /* Disable OTG Overcurrent Detection */ /* USBCMD */ -#define UH1_USBCMD_OFFSET 0x140 #define UCMD_RUN_STOP (1 << 0) /* controller run/stop */ #define UCMD_RESET (1 << 1) /* controller reset */ -static void usbh1_internal_phy_clock_gate(int on) +static const unsigned phy_bases[] = { + USB_PHY0_BASE_ADDR, + USB_PHY1_BASE_ADDR, +}; + +static void usb_internal_phy_clock_gate(int index, int on) { - void __iomem *phy_reg = (void __iomem *)USB_PHY1_BASE_ADDR; + void __iomem *phy_reg; + + if (index >= ARRAY_SIZE(phy_bases)) + return; + phy_reg = (void __iomem *)phy_bases[index]; phy_reg += on ? USBPHY_CTRL_CLR : USBPHY_CTRL_SET; __raw_writel(USBPHY_CTRL_CLKGATE, phy_reg); } -static void usbh1_power_config(void) +static void usb_power_config(int index) { struct anatop_regs __iomem *anatop = (struct anatop_regs __iomem *)ANATOP_BASE_ADDR; + void __iomem *chrg_detect; + void __iomem *pll_480_ctrl_clr; + void __iomem *pll_480_ctrl_set; + + switch (index) { + case 0: + chrg_detect = &anatop->usb1_chrg_detect; + pll_480_ctrl_clr = &anatop->usb1_pll_480_ctrl_clr; + pll_480_ctrl_set = &anatop->usb1_pll_480_ctrl_set; + break; + case 1: + chrg_detect = &anatop->usb2_chrg_detect; + pll_480_ctrl_clr = &anatop->usb2_pll_480_ctrl_clr; + pll_480_ctrl_set = &anatop->usb2_pll_480_ctrl_set; + break; + default: + return; + } /* - * Some phy and power's special controls for host1 + * Some phy and power's special controls * 1. The external charger detector needs to be disabled * or the signal at DP will be poor - * 2. The PLL's power and output to usb for host 1 + * 2. The PLL's power and output to usb * is totally controlled by IC, so the Software only needs * to enable them at initializtion. */ __raw_writel(ANADIG_USB2_CHRG_DETECT_EN_B | ANADIG_USB2_CHRG_DETECT_CHK_CHRG_B, - &anatop->usb2_chrg_detect); + chrg_detect); __raw_writel(ANADIG_USB2_PLL_480_CTRL_BYPASS, - &anatop->usb2_pll_480_ctrl_clr); + pll_480_ctrl_clr); __raw_writel(ANADIG_USB2_PLL_480_CTRL_ENABLE | ANADIG_USB2_PLL_480_CTRL_POWER | ANADIG_USB2_PLL_480_CTRL_EN_USB_CLKS, - &anatop->usb2_pll_480_ctrl_set); + pll_480_ctrl_set); } -static int usbh1_phy_enable(void) +/* Return 0 : host node, <>0 : device mode */ +static int usb_phy_enable(int index, struct usb_ehci *ehci) { - void __iomem *phy_reg = (void __iomem *)USB_PHY1_BASE_ADDR; - void __iomem *phy_ctrl = (void __iomem *)(phy_reg + USBPHY_CTRL); - void __iomem *usb_cmd = (void __iomem *)(USBOH3_USB_BASE_ADDR + - USB_H1REGS_OFFSET + - UH1_USBCMD_OFFSET); + void __iomem *phy_reg; + void __iomem *phy_ctrl; + void __iomem *usb_cmd; u32 val; + if (index >= ARRAY_SIZE(phy_bases)) + return 0; + + phy_reg = (void __iomem *)phy_bases[index]; + phy_ctrl = (void __iomem *)(phy_reg + USBPHY_CTRL); + usb_cmd = (void __iomem *)&ehci->usbcmd; + /* Stop then Reset */ val = __raw_readl(usb_cmd); val &= ~UCMD_RUN_STOP; @@ -123,31 +156,41 @@ static int usbh1_phy_enable(void) /* Power up the PHY */ __raw_writel(0, phy_reg + USBPHY_PWD); /* enable FS/LS device */ - val = __raw_readl(phy_reg + USBPHY_CTRL); + val = __raw_readl(phy_ctrl); val |= (USBPHY_CTRL_ENUTMILEVEL2 | USBPHY_CTRL_ENUTMILEVEL3); - __raw_writel(val, phy_reg + USBPHY_CTRL); + __raw_writel(val, phy_ctrl); - return 0; + return val & USBPHY_CTRL_OTG_ID; } -static void usbh1_oc_config(void) +/* Base address for this IP block is 0x02184800 */ +struct usbnc_regs { + u32 ctrl[4]; /* otg/host1-3 */ + u32 uh2_hsic_ctrl; + u32 uh3_hsic_ctrl; + u32 otg_phy_ctrl_0; + u32 uh1_phy_ctrl_0; +}; + +static void usb_oc_config(int index) { - void __iomem *usb_base = (void __iomem *)USBOH3_USB_BASE_ADDR; - void __iomem *usbother_base = usb_base + USB_OTHERREGS_OFFSET; + struct usbnc_regs *usbnc = (struct usbnc_regs *)(USBOH3_USB_BASE_ADDR + + USB_OTHERREGS_OFFSET); + void __iomem *ctrl = (void __iomem *)(&usbnc->ctrl[index]); u32 val; - val = __raw_readl(usbother_base + USB_H1_CTRL_OFFSET); + val = __raw_readl(ctrl); #if CONFIG_MACH_TYPE == MACH_TYPE_MX6Q_ARM2 /* mx6qarm2 seems to required a different setting*/ val &= ~UCTRL_OVER_CUR_POL; #else val |= UCTRL_OVER_CUR_POL; #endif - __raw_writel(val, usbother_base + USB_H1_CTRL_OFFSET); + __raw_writel(val, ctrl); - val = __raw_readl(usbother_base + USB_H1_CTRL_OFFSET); + val = __raw_readl(ctrl); val |= UCTRL_OVER_CUR_DIS; - __raw_writel(val, usbother_base + USB_H1_CTRL_OFFSET); + __raw_writel(val, ctrl); } int __weak board_ehci_hcd_init(int port) @@ -155,34 +198,42 @@ int __weak board_ehci_hcd_init(int port) return 0; } +int __weak board_ehci_power(int port, int on) +{ + return 0; +} + int ehci_hcd_init(int index, enum usb_init_type init, struct ehci_hccr **hccr, struct ehci_hcor **hcor) { - struct usb_ehci *ehci; + enum usb_init_type type; + struct usb_ehci *ehci = (struct usb_ehci *)(USBOH3_USB_BASE_ADDR + + (0x200 * index)); + if (index > 3) + return -EINVAL; enable_usboh3_clk(1); mdelay(1); /* Do board specific initialization */ - board_ehci_hcd_init(CONFIG_MXC_USB_PORT); - -#if CONFIG_MXC_USB_PORT == 1 - /* USB Host 1 */ - usbh1_power_config(); - usbh1_oc_config(); - usbh1_internal_phy_clock_gate(1); - usbh1_phy_enable(); -#else -#error "MXC USB port not yet supported" -#endif + board_ehci_hcd_init(index); + + usb_power_config(index); + usb_oc_config(index); + usb_internal_phy_clock_gate(index, 1); + type = usb_phy_enable(index, ehci) ? USB_INIT_DEVICE : USB_INIT_HOST; - ehci = (struct usb_ehci *)(USBOH3_USB_BASE_ADDR + - (0x200 * CONFIG_MXC_USB_PORT)); *hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength); *hcor = (struct ehci_hcor *)((uint32_t)*hccr + HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase))); - setbits_le32(&ehci->usbmode, CM_HOST); + if ((type == init) || (type == USB_INIT_DEVICE)) + board_ehci_power(index, (type == USB_INIT_DEVICE) ? 0 : 1); + if (type != init) + return -ENODEV; + if (type == USB_INIT_DEVICE) + return 0; + setbits_le32(&ehci->usbmode, CM_HOST); __raw_writel(CONFIG_MXC_USB_PORTSC, &ehci->portsc); setbits_le32(&ehci->portsc, USB_EN); |