diff options
Diffstat (limited to 'drivers/usb/host')
| -rw-r--r-- | drivers/usb/host/ehci-omap.c | 209 |
1 files changed, 154 insertions, 55 deletions
diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c index 93d3bb7..00f787f 100644 --- a/drivers/usb/host/ehci-omap.c +++ b/drivers/usb/host/ehci-omap.c @@ -27,14 +27,78 @@ */ #include <common.h> #include <usb.h> +#include <usb/ulpi.h> +#include <errno.h> #include <asm/io.h> #include <asm/gpio.h> -#include <asm/arch/clocks.h> -#include <asm/arch/clocks_omap3.h> -#include <asm/arch/ehci_omap3.h> -#include <asm/arch/sys_proto.h> +#include <asm/arch/ehci.h> +#include <asm/ehci-omap.h> #include "ehci-core.h" +static struct omap_uhh *const uhh = (struct omap_uhh *)OMAP_UHH_BASE; +static struct omap_usbtll *const usbtll = (struct omap_usbtll *)OMAP_USBTLL_BASE; +static struct omap_ehci *const ehci = (struct omap_ehci *)OMAP_EHCI_BASE; + +static int omap_uhh_reset(void) +{ + unsigned long init = get_timer(0); + + /* perform UHH soft reset, and wait until reset is complete */ + writel(OMAP_UHH_SYSCONFIG_SOFTRESET, &uhh->sysc); + + /* Wait for UHH reset to complete */ + while (!(readl(&uhh->syss) & OMAP_UHH_SYSSTATUS_EHCI_RESETDONE)) + if (get_timer(init) > CONFIG_SYS_HZ) { + debug("OMAP UHH error: timeout resetting ehci\n"); + return -EL3RST; + } + + return 0; +} + +static int omap_ehci_tll_reset(void) +{ + unsigned long init = get_timer(0); + + /* perform TLL soft reset, and wait until reset is complete */ + writel(OMAP_USBTLL_SYSCONFIG_SOFTRESET, &usbtll->sysc); + + /* Wait for TLL reset to complete */ + while (!(readl(&usbtll->syss) & OMAP_USBTLL_SYSSTATUS_RESETDONE)) + if (get_timer(init) > CONFIG_SYS_HZ) { + debug("OMAP EHCI error: timeout resetting TLL\n"); + return -EL3RST; + } + + return 0; +} + +static void omap_usbhs_hsic_init(int port) +{ + unsigned int reg; + + /* Enable channels now */ + reg = readl(&usbtll->channel_conf + port); + + setbits_le32(®, (OMAP_TLL_CHANNEL_CONF_CHANMODE_TRANSPARENT_UTMI + | OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF + | OMAP_TLL_CHANNEL_CONF_DRVVBUS + | OMAP_TLL_CHANNEL_CONF_CHRGVBUS + | OMAP_TLL_CHANNEL_CONF_CHANEN)); + + writel(reg, &usbtll->channel_conf + port); +} + +static void omap_ehci_soft_phy_reset(int port) +{ + struct ulpi_viewport ulpi_vp; + + ulpi_vp.viewport_addr = (u32)&ehci->insreg05_utmi_ulpi; + ulpi_vp.port_num = port; + + ulpi_reset(&ulpi_vp); +} + inline int __board_usb_init(void) { return 0; @@ -72,31 +136,31 @@ static inline void omap_ehci_phy_reset(int on, int delay) #endif /* Reset is needed otherwise the kernel-driver will throw an error. */ -int ehci_hcd_stop(void) +int omap_ehci_hcd_stop(void) { - debug("Resetting OMAP3 EHCI\n"); + debug("Resetting OMAP EHCI\n"); omap_ehci_phy_reset(1, 0); - writel(OMAP_UHH_SYSCONFIG_SOFTRESET, - OMAP3_UHH_BASE + OMAP_UHH_SYSCONFIG); - /* disable USB clocks */ - struct prcm *prcm_base = (struct prcm *)PRCM_BASE; - sr32(&prcm_base->iclken_usbhost, 0, 1, 0); - sr32(&prcm_base->fclken_usbhost, 0, 2, 0); - sr32(&prcm_base->iclken3_core, 2, 1, 0); - sr32(&prcm_base->fclken3_core, 2, 1, 0); + + if (omap_uhh_reset() < 0) + return -1; + + if (omap_ehci_tll_reset() < 0) + return -1; + return 0; } /* - * Initialize the OMAP3 EHCI controller and PHY. - * Based on "drivers/usb/host/ehci-omap.c" from Linux 2.6.37. + * Initialize the OMAP EHCI controller and PHY. + * Based on "drivers/usb/host/ehci-omap.c" from Linux 3.1 * See there for additional Copyrights. */ -int ehci_hcd_init(void) +int omap_ehci_hcd_init(struct omap_usbhs_board_data *usbhs_pdata) { int ret; + unsigned int i, reg = 0, rev = 0; - debug("Initializing OMAP3 EHCI\n"); + debug("Initializing OMAP EHCI\n"); ret = board_usb_init(); if (ret < 0) @@ -105,52 +169,87 @@ int ehci_hcd_init(void) /* Put the PHY in RESET */ omap_ehci_phy_reset(1, 10); - struct prcm *prcm_base = (struct prcm *)PRCM_BASE; - /* Enable USBHOST_L3_ICLK (USBHOST_MICLK) */ - sr32(&prcm_base->iclken_usbhost, 0, 1, 1); - /* - * Enable USBHOST_48M_FCLK (USBHOST_FCLK1) - * and USBHOST_120M_FCLK (USBHOST_FCLK2) - */ - sr32(&prcm_base->fclken_usbhost, 0, 2, 3); - /* Enable USBTTL_ICLK */ - sr32(&prcm_base->iclken3_core, 2, 1, 1); - /* Enable USBTTL_FCLK */ - sr32(&prcm_base->fclken3_core, 2, 1, 1); - debug("USB clocks enabled\n"); + ret = omap_uhh_reset(); + if (ret < 0) + return ret; - /* perform TLL soft reset, and wait until reset is complete */ - writel(OMAP_USBTLL_SYSCONFIG_SOFTRESET, - OMAP3_USBTLL_BASE + OMAP_USBTLL_SYSCONFIG); - /* Wait for TLL reset to complete */ - while (!(readl(OMAP3_USBTLL_BASE + OMAP_USBTLL_SYSSTATUS) - & OMAP_USBTLL_SYSSTATUS_RESETDONE)) - ; - debug("TLL reset done\n"); + ret = omap_ehci_tll_reset(); + if (ret) + return ret; writel(OMAP_USBTLL_SYSCONFIG_ENAWAKEUP | OMAP_USBTLL_SYSCONFIG_SIDLEMODE | - OMAP_USBTLL_SYSCONFIG_CACTIVITY, - OMAP3_USBTLL_BASE + OMAP_USBTLL_SYSCONFIG); + OMAP_USBTLL_SYSCONFIG_CACTIVITY, &usbtll->sysc); /* Put UHH in NoIdle/NoStandby mode */ - writel(OMAP_UHH_SYSCONFIG_ENAWAKEUP - | OMAP_UHH_SYSCONFIG_SIDLEMODE - | OMAP_UHH_SYSCONFIG_CACTIVITY - | OMAP_UHH_SYSCONFIG_MIDLEMODE, - OMAP3_UHH_BASE + OMAP_UHH_SYSCONFIG); - - /* setup burst configurations */ - writel(OMAP_UHH_HOSTCONFIG_INCR4_BURST_EN - | OMAP_UHH_HOSTCONFIG_INCR8_BURST_EN - | OMAP_UHH_HOSTCONFIG_INCR16_BURST_EN, - OMAP3_UHH_BASE + OMAP_UHH_HOSTCONFIG); + writel(OMAP_UHH_SYSCONFIG_VAL, &uhh->sysc); + + /* setup ULPI bypass and burst configurations */ + clrsetbits_le32(®, OMAP_UHH_HOSTCONFIG_INCRX_ALIGN_EN, + (OMAP_UHH_HOSTCONFIG_INCR4_BURST_EN | + OMAP_UHH_HOSTCONFIG_INCR8_BURST_EN | + OMAP_UHH_HOSTCONFIG_INCR16_BURST_EN)); + + rev = readl(&uhh->rev); + if (rev == OMAP_USBHS_REV1) { + if (is_ehci_phy_mode(usbhs_pdata->port_mode[0])) + clrbits_le32(®, OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS); + else + setbits_le32(®, OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS); + + if (is_ehci_phy_mode(usbhs_pdata->port_mode[1])) + clrbits_le32(®, OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS); + else + setbits_le32(®, OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS); + + if (is_ehci_phy_mode(usbhs_pdata->port_mode[2])) + clrbits_le32(®, OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS); + else + setbits_le32(®, OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS); + } else if (rev == OMAP_USBHS_REV2) { + clrsetbits_le32(®, (OMAP_P1_MODE_CLEAR | OMAP_P2_MODE_CLEAR), + OMAP4_UHH_HOSTCONFIG_APP_START_CLK); + + /* Clear port mode fields for PHY mode*/ + + if (is_ehci_hsic_mode(usbhs_pdata->port_mode[0])) + setbits_le32(®, OMAP_P1_MODE_HSIC); + + if (is_ehci_hsic_mode(usbhs_pdata->port_mode[1])) + setbits_le32(®, OMAP_P2_MODE_HSIC); + + if (is_ehci_hsic_mode(usbhs_pdata->port_mode[2])) + setbits_le32(®, OMAP_P3_MODE_HSIC); + } + + debug("OMAP UHH_REVISION 0x%x\n", rev); + writel(reg, &uhh->hostconfig); + + for (i = 0; i < OMAP_HS_USB_PORTS; i++) + if (is_ehci_hsic_mode(usbhs_pdata->port_mode[i])) + omap_usbhs_hsic_init(i); omap_ehci_phy_reset(0, 10); - hccr = (struct ehci_hccr *)(OMAP3_EHCI_BASE); - hcor = (struct ehci_hcor *)(OMAP3_EHCI_BASE + 0x10); + /* + * An undocumented "feature" in the OMAP3 EHCI controller, + * causes suspended ports to be taken out of suspend when + * the USBCMD.Run/Stop bit is cleared (for example when + * we do ehci_bus_suspend). + * This breaks suspend-resume if the root-hub is allowed + * to suspend. Writing 1 to this undocumented register bit + * disables this feature and restores normal behavior. + */ + writel(EHCI_INSNREG04_DISABLE_UNSUSPEND, &ehci->insreg04); + + for (i = 0; i < OMAP_HS_USB_PORTS; i++) + if (is_ehci_phy_mode(usbhs_pdata->port_mode[i])) + omap_ehci_soft_phy_reset(i); + + dcache_disable(); + hccr = (struct ehci_hccr *)(OMAP_EHCI_BASE); + hcor = (struct ehci_hcor *)(OMAP_EHCI_BASE + 0x10); - debug("OMAP3 EHCI init done\n"); + debug("OMAP EHCI init done\n"); return 0; } |