summaryrefslogtreecommitdiff
path: root/drivers/ns8382x.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/ns8382x.c')
-rw-r--r--drivers/ns8382x.c863
1 files changed, 863 insertions, 0 deletions
diff --git a/drivers/ns8382x.c b/drivers/ns8382x.c
new file mode 100644
index 0000000..978080e
--- /dev/null
+++ b/drivers/ns8382x.c
@@ -0,0 +1,863 @@
+/*
+ ns8382x.c: A U-Boot driver for the NatSemi DP8382[01].
+ ported by: Mark A. Rakes (mark_rakes@vivato.net)
+
+ Adapted from:
+ 1. an Etherboot driver for DP8381[56] written by:
+ Copyright (C) 2001 Entity Cyber, Inc.
+
+ This development of this Etherboot driver was funded by
+ Sicom Systems: http://www.sicompos.com/
+
+ Author: Marty Connor (mdc@thinguin.org)
+ Adapted from a Linux driver which was written by Donald Becker
+
+ This software may be used and distributed according to the terms
+ of the GNU Public License (GPL), incorporated herein by reference.
+
+ 2. A Linux driver by Donald Becker, ns820.c:
+ Written/copyright 1999-2002 by Donald Becker.
+
+ This software may be used and distributed according to the terms of
+ the GNU General Public License (GPL), incorporated herein by reference.
+ Drivers based on or derived from this code fall under the GPL and must
+ retain the authorship, copyright and license notice. This file is not
+ a complete program and may only be used when the entire operating
+ system is licensed under the GPL. License for under other terms may be
+ available. Contact the original author for details.
+
+ The original author may be reached as becker@scyld.com, or at
+ Scyld Computing Corporation
+ 410 Severn Ave., Suite 210
+ Annapolis MD 21403
+
+ Support information and updates available at
+ http://www.scyld.com/network/netsemi.html
+
+ Datasheets available from:
+ http://www.national.com/pf/DP/DP83820.html
+ http://www.national.com/pf/DP/DP83821.html
+*/
+
+/* Revision History
+ * October 2002 mar 1.0
+ * Initial U-Boot Release.
+ * Tested with Netgear GA622T (83820)
+ * and SMC9452TX (83821)
+ * NOTE: custom boards with these chips may (likely) require
+ * a programmed EEPROM device (if present) in order to work
+ * correctly.
+*/
+
+/* Includes */
+#include <common.h>
+#include <malloc.h>
+#include <net.h>
+#include <asm/io.h>
+#include <pci.h>
+
+#if (CONFIG_COMMANDS & CFG_CMD_NET) && defined(CONFIG_NET_MULTI) && \
+ defined(CONFIG_NS8382X)
+
+/* defines */
+#define DSIZE 0x00000FFF
+#define ETH_ALEN 6
+#define CRC_SIZE 4
+#define TOUT_LOOP 500000
+#define TX_BUF_SIZE 1536
+#define RX_BUF_SIZE 1536
+#define NUM_RX_DESC 4 /* Number of Rx descriptor registers. */
+
+enum register_offsets {
+ ChipCmd = 0x00,
+ ChipConfig = 0x04,
+ EECtrl = 0x08,
+ IntrMask = 0x14,
+ IntrEnable = 0x18,
+ TxRingPtr = 0x20,
+ TxRingPtrHi = 0x24,
+ TxConfig = 0x28,
+ RxRingPtr = 0x30,
+ RxRingPtrHi = 0x34,
+ RxConfig = 0x38,
+ PriQueue = 0x3C,
+ RxFilterAddr = 0x48,
+ RxFilterData = 0x4C,
+ ClkRun = 0xCC,
+ PCIPM = 0x44,
+};
+
+enum ChipCmdBits {
+ ChipReset = 0x100,
+ RxReset = 0x20,
+ TxReset = 0x10,
+ RxOff = 0x08,
+ RxOn = 0x04,
+ TxOff = 0x02,
+ TxOn = 0x01
+};
+
+enum ChipConfigBits {
+ LinkSts = 0x80000000,
+ GigSpeed = 0x40000000,
+ HundSpeed = 0x20000000,
+ FullDuplex = 0x10000000,
+ TBIEn = 0x01000000,
+ Mode1000 = 0x00400000,
+ T64En = 0x00004000,
+ D64En = 0x00001000,
+ M64En = 0x00000800,
+ PhyRst = 0x00000400,
+ PhyDis = 0x00000200,
+ ExtStEn = 0x00000100,
+ BEMode = 0x00000001,
+};
+#define SpeedStatus_Polarity ( GigSpeed | HundSpeed | FullDuplex)
+
+enum TxConfig_bits {
+ TxDrthMask = 0x000000ff,
+ TxFlthMask = 0x0000ff00,
+ TxMxdmaMask = 0x00700000,
+ TxMxdma_8 = 0x00100000,
+ TxMxdma_16 = 0x00200000,
+ TxMxdma_32 = 0x00300000,
+ TxMxdma_64 = 0x00400000,
+ TxMxdma_128 = 0x00500000,
+ TxMxdma_256 = 0x00600000,
+ TxMxdma_512 = 0x00700000,
+ TxMxdma_1024 = 0x00000000,
+ TxCollRetry = 0x00800000,
+ TxAutoPad = 0x10000000,
+ TxMacLoop = 0x20000000,
+ TxHeartIgn = 0x40000000,
+ TxCarrierIgn = 0x80000000
+};
+
+enum RxConfig_bits {
+ RxDrthMask = 0x0000003e,
+ RxMxdmaMask = 0x00700000,
+ RxMxdma_8 = 0x00100000,
+ RxMxdma_16 = 0x00200000,
+ RxMxdma_32 = 0x00300000,
+ RxMxdma_64 = 0x00400000,
+ RxMxdma_128 = 0x00500000,
+ RxMxdma_256 = 0x00600000,
+ RxMxdma_512 = 0x00700000,
+ RxMxdma_1024 = 0x00000000,
+ RxAcceptLenErr = 0x04000000,
+ RxAcceptLong = 0x08000000,
+ RxAcceptTx = 0x10000000,
+ RxStripCRC = 0x20000000,
+ RxAcceptRunt = 0x40000000,
+ RxAcceptErr = 0x80000000,
+};
+
+/* Bits in the RxMode register. */
+enum rx_mode_bits {
+ RxFilterEnable = 0x80000000,
+ AcceptAllBroadcast = 0x40000000,
+ AcceptAllMulticast = 0x20000000,
+ AcceptAllUnicast = 0x10000000,
+ AcceptPerfectMatch = 0x08000000,
+};
+
+typedef struct _BufferDesc {
+ u32 link;
+ u32 bufptr;
+ vu_long cmdsts;
+ u32 extsts; /*not used here */
+} BufferDesc;
+
+/* Bits in network_desc.status */
+enum desc_status_bits {
+ DescOwn = 0x80000000, DescMore = 0x40000000, DescIntr = 0x20000000,
+ DescNoCRC = 0x10000000, DescPktOK = 0x08000000,
+ DescSizeMask = 0xfff,
+
+ DescTxAbort = 0x04000000, DescTxFIFO = 0x02000000,
+ DescTxCarrier = 0x01000000, DescTxDefer = 0x00800000,
+ DescTxExcDefer = 0x00400000, DescTxOOWCol = 0x00200000,
+ DescTxExcColl = 0x00100000, DescTxCollCount = 0x000f0000,
+
+ DescRxAbort = 0x04000000, DescRxOver = 0x02000000,
+ DescRxDest = 0x01800000, DescRxLong = 0x00400000,
+ DescRxRunt = 0x00200000, DescRxInvalid = 0x00100000,
+ DescRxCRC = 0x00080000, DescRxAlign = 0x00040000,
+ DescRxLoop = 0x00020000, DesRxColl = 0x00010000,
+};
+
+/* Bits in MEAR */
+enum mii_reg_bits {
+ MDIO_ShiftClk = 0x0040,
+ MDIO_EnbOutput = 0x0020,
+ MDIO_Data = 0x0010,
+};
+
+/* PHY Register offsets. */
+enum phy_reg_offsets {
+ BMCR = 0x00,
+ BMSR = 0x01,
+ PHYIDR1 = 0x02,
+ PHYIDR2 = 0x03,
+ ANAR = 0x04,
+ KTCR = 0x09,
+};
+
+/* basic mode control register bits */
+enum bmcr_bits {
+ Bmcr_Reset = 0x8000,
+ Bmcr_Loop = 0x4000,
+ Bmcr_Speed0 = 0x2000,
+ Bmcr_AutoNegEn = 0x1000, /*if set ignores Duplex, Speed[01] */
+ Bmcr_RstAutoNeg = 0x0200,
+ Bmcr_Duplex = 0x0100,
+ Bmcr_Speed1 = 0x0040,
+ Bmcr_Force10H = 0x0000,
+ Bmcr_Force10F = 0x0100,
+ Bmcr_Force100H = 0x2000,
+ Bmcr_Force100F = 0x2100,
+ Bmcr_Force1000H = 0x0040,
+ Bmcr_Force1000F = 0x0140,
+};
+
+/* auto negotiation advertisement register */
+enum anar_bits {
+ anar_adv_100F = 0x0100,
+ anar_adv_100H = 0x0080,
+ anar_adv_10F = 0x0040,
+ anar_adv_10H = 0x0020,
+ anar_ieee_8023 = 0x0001,
+};
+
+/* 1K-base T control register */
+enum ktcr_bits {
+ ktcr_adv_1000H = 0x0100,
+ ktcr_adv_1000F = 0x0200,
+};
+
+/* Globals */
+static u32 SavedClkRun;
+static unsigned int cur_rx;
+static unsigned int rx_config;
+static unsigned int tx_config;
+
+/* Note: transmit and receive buffers and descriptors must be
+ long long word aligned */
+static BufferDesc txd __attribute__ ((aligned(8)));
+static BufferDesc rxd[NUM_RX_DESC] __attribute__ ((aligned(8)));
+static unsigned char txb[TX_BUF_SIZE] __attribute__ ((aligned(8)));
+static unsigned char rxb[NUM_RX_DESC * RX_BUF_SIZE]
+ __attribute__ ((aligned(8)));
+
+/* Function Prototypes */
+static int mdio_read(struct eth_device *dev, int phy_id, int addr);
+static void mdio_write(struct eth_device *dev, int phy_id, int addr, int value);
+static void mdio_sync(struct eth_device *dev, u32 offset);
+static int ns8382x_init(struct eth_device *dev, bd_t * bis);
+static void ns8382x_reset(struct eth_device *dev);
+static void ns8382x_init_rxfilter(struct eth_device *dev);
+static void ns8382x_init_txd(struct eth_device *dev);
+static void ns8382x_init_rxd(struct eth_device *dev);
+static void ns8382x_set_rx_mode(struct eth_device *dev);
+static void ns8382x_check_duplex(struct eth_device *dev);
+static int ns8382x_send(struct eth_device *dev, volatile void *packet,
+ int length);
+static int ns8382x_poll(struct eth_device *dev);
+static void ns8382x_disable(struct eth_device *dev);
+
+static struct pci_device_id supported[] = {
+ {PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_8382x},
+ {}
+};
+
+#define bus_to_phys(a) pci_mem_to_phys((pci_dev_t)dev->priv, a)
+#define phys_to_bus(a) pci_phys_to_mem((pci_dev_t)dev->priv, a)
+
+static inline int
+INW(struct eth_device *dev, u_long addr)
+{
+ return le16_to_cpu(*(vu_short *) (addr + dev->iobase));
+}
+
+static int
+INL(struct eth_device *dev, u_long addr)
+{
+ return le32_to_cpu(*(vu_long *) (addr + dev->iobase));
+}
+
+static inline void
+OUTW(struct eth_device *dev, int command, u_long addr)
+{
+ *(vu_short *) ((addr + dev->iobase)) = cpu_to_le16(command);
+}
+
+static inline void
+OUTL(struct eth_device *dev, int command, u_long addr)
+{
+ *(vu_long *) ((addr + dev->iobase)) = cpu_to_le32(command);
+}
+
+/* Function: ns8382x_initialize
+ * Description: Retrieves the MAC address of the card, and sets up some
+ * globals required by other routines, and initializes the NIC, making it
+ * ready to send and receive packets.
+ * Side effects: initializes ns8382xs, ready to recieve packets.
+ * Returns: int: number of cards found
+ */
+
+int
+ns8382x_initialize(bd_t * bis)
+{
+ pci_dev_t devno;
+ int card_number = 0;
+ struct eth_device *dev;
+ u32 iobase, status;
+ int i, idx = 0;
+ u32 phyAddress;
+ u32 tmp;
+ u32 chip_config;
+
+ while (1) { /* Find PCI device(s) */
+ if ((devno = pci_find_devices(supported, idx++)) < 0)
+ break;
+
+ pci_read_config_dword(devno, PCI_BASE_ADDRESS_0, &iobase);
+ iobase &= ~0x3; /* 1: unused and 0:I/O Space Indicator */
+
+#ifdef NS8382X_DEBUG
+ printf("ns8382x: NatSemi dp8382x @ 0x%x\n", iobase);
+#endif
+
+ pci_write_config_dword(devno, PCI_COMMAND,
+ PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
+
+ /* Check if I/O accesses and Bus Mastering are enabled. */
+ pci_read_config_dword(devno, PCI_COMMAND, &status);
+ if (!(status & PCI_COMMAND_MEMORY)) {
+ printf("Error: Can not enable MEM access.\n");
+ continue;
+ } else if (!(status & PCI_COMMAND_MASTER)) {
+ printf("Error: Can not enable Bus Mastering.\n");
+ continue;
+ }
+
+ dev = (struct eth_device *) malloc(sizeof *dev);
+
+ sprintf(dev->name, "dp8382x#%d", card_number);
+ dev->iobase = bus_to_phys(iobase);
+ dev->priv = (void *) devno;
+ dev->init = ns8382x_init;
+ dev->halt = ns8382x_disable;
+ dev->send = ns8382x_send;
+ dev->recv = ns8382x_poll;
+
+ /* ns8382x has a non-standard PM control register
+ * in PCI config space. Some boards apparently need
+ * to be brought to D0 in this manner. */
+ pci_read_config_dword(devno, PCIPM, &tmp);
+ if (tmp & (0x03 | 0x100)) { /* D0 state, disable PME assertion */
+ u32 newtmp = tmp & ~(0x03 | 0x100);
+ pci_write_config_dword(devno, PCIPM, newtmp);
+ }
+
+ /* get MAC address */
+ for (i = 0; i < 3; i++) {
+ u32 data;
+ char *mac = &dev->enetaddr[i * 2];
+
+ OUTL(dev, i * 2, RxFilterAddr);
+ data = INL(dev, RxFilterData);
+ *mac++ = data;
+ *mac++ = data >> 8;
+ }
+ /* get PHY address, can't be zero */
+ for (phyAddress = 1; phyAddress < 32; phyAddress++) {
+ u32 rev, phy1;
+
+ phy1 = mdio_read(dev, phyAddress, PHYIDR1);
+ if (phy1 == 0x2000) { /*check for 83861/91 */
+ rev = mdio_read(dev, phyAddress, PHYIDR2);
+ if ((rev & ~(0x000f)) == 0x00005c50 ||
+ (rev & ~(0x000f)) == 0x00005c60) {
+#ifdef NS8382X_DEBUG
+ printf("phy rev is %x\n", rev);
+ printf("phy address is %x\n",
+ phyAddress);
+#endif
+ break;
+ }
+ }
+ }
+
+ /* set phy to autonegotiate && advertise everything */
+ mdio_write(dev, phyAddress, KTCR,
+ (ktcr_adv_1000H | ktcr_adv_1000F));
+ mdio_write(dev, phyAddress, ANAR,
+ (anar_adv_100F | anar_adv_100H | anar_adv_10H |
+ anar_adv_10F | anar_ieee_8023));
+ mdio_write(dev, phyAddress, BMCR, 0x0); /*restore */
+ mdio_write(dev, phyAddress, BMCR,
+ (Bmcr_AutoNegEn | Bmcr_RstAutoNeg));
+ /* Reset the chip to erase any previous misconfiguration. */
+ OUTL(dev, (ChipReset), ChipCmd);
+
+ chip_config = INL(dev, ChipConfig);
+ /* reset the phy */
+ OUTL(dev, (chip_config | PhyRst), ChipConfig);
+ /* power up and initialize transceiver */
+ OUTL(dev, (chip_config & ~(PhyDis)), ChipConfig);
+
+ mdio_sync(dev, EECtrl);
+#ifdef NS8382X_DEBUG
+ {
+ u32 chpcfg =
+ INL(dev, ChipConfig) ^ SpeedStatus_Polarity;
+
+ printf("%s: Transceiver 10%s %s duplex.\n", dev->name,
+ (chpcfg & GigSpeed) ? "00" : (chpcfg & HundSpeed)
+ ? "0" : "",
+ chpcfg & FullDuplex ? "full" : "half");
+ printf("%s: %02x:%02x:%02x:%02x:%02x:%02x\n", dev->name,
+ dev->enetaddr[0], dev->enetaddr[1],
+ dev->enetaddr[2], dev->enetaddr[3],
+ dev->enetaddr[4], dev->enetaddr[5]);
+ }
+#endif
+ /* Disable PME:
+ * The PME bit is initialized from the EEPROM contents.
+ * PCI cards probably have PME disabled, but motherboard
+ * implementations may have PME set to enable WakeOnLan.
+ * With PME set the chip will scan incoming packets but
+ * nothing will be written to memory. */
+ SavedClkRun = INL(dev, ClkRun);
+ OUTL(dev, SavedClkRun & ~0x100, ClkRun);
+
+ eth_register(dev);
+
+ card_number++;
+
+ pci_write_config_byte(devno, PCI_LATENCY_TIMER, 0x60);
+
+ udelay(10 * 1000);
+ }
+ return card_number;
+}
+
+/* MII transceiver control section.
+ Read and write MII registers using software-generated serial MDIO
+ protocol. See the MII specifications or DP83840A data sheet for details.
+
+ The maximum data clock rate is 2.5 Mhz. To meet minimum timing we
+ must flush writes to the PCI bus with a PCI read. */
+#define mdio_delay(mdio_addr) INL(dev, mdio_addr)
+
+#define MDIO_EnbIn (0)
+#define MDIO_WRITE0 (MDIO_EnbOutput)
+#define MDIO_WRITE1 (MDIO_Data | MDIO_EnbOutput)
+
+/* Generate the preamble required for initial synchronization and
+ a few older transceivers. */
+static void
+mdio_sync(struct eth_device *dev, u32 offset)
+{
+ int bits = 32;
+
+ /* Establish sync by sending at least 32 logic ones. */
+ while (--bits >= 0) {
+ OUTL(dev, MDIO_WRITE1, offset);
+ mdio_delay(offset);
+ OUTL(dev, MDIO_WRITE1 | MDIO_ShiftClk, offset);
+ mdio_delay(offset);
+ }
+}
+
+static int
+mdio_read(struct eth_device *dev, int phy_id, int addr)
+{
+ int mii_cmd = (0xf6 << 10) | (phy_id << 5) | addr;
+ int i, retval = 0;
+
+ /* Shift the read command bits out. */
+ for (i = 15; i >= 0; i--) {
+ int dataval = (mii_cmd & (1 << i)) ? MDIO_WRITE1 : MDIO_WRITE0;
+
+ OUTL(dev, dataval, EECtrl);
+ mdio_delay(EECtrl);
+ OUTL(dev, dataval | MDIO_ShiftClk, EECtrl);
+ mdio_delay(EECtrl);
+ }
+ /* Read the two transition, 16 data, and wire-idle bits. */
+ for (i = 19; i > 0; i--) {
+ OUTL(dev, MDIO_EnbIn, EECtrl);
+ mdio_delay(EECtrl);
+ retval =
+ (retval << 1) | ((INL(dev, EECtrl) & MDIO_Data) ? 1 : 0);
+ OUTL(dev, MDIO_EnbIn | MDIO_ShiftClk, EECtrl);
+ mdio_delay(EECtrl);
+ }
+ return (retval >> 1) & 0xffff;
+}
+
+static void
+mdio_write(struct eth_device *dev, int phy_id, int addr, int value)
+{
+ int mii_cmd = (0x5002 << 16) | (phy_id << 23) | (addr << 18) | value;
+ int i;
+
+ /* Shift the command bits out. */
+ for (i = 31; i >= 0; i--) {
+ int dataval = (mii_cmd & (1 << i)) ? MDIO_WRITE1 : MDIO_WRITE0;
+
+ OUTL(dev, dataval, EECtrl);
+ mdio_delay(EECtrl);
+ OUTL(dev, dataval | MDIO_ShiftClk, EECtrl);
+ mdio_delay(EECtrl);
+ }
+ /* Clear out extra bits. */
+ for (i = 2; i > 0; i--) {
+ OUTL(dev, MDIO_EnbIn, EECtrl);
+ mdio_delay(EECtrl);
+ OUTL(dev, MDIO_EnbIn | MDIO_ShiftClk, EECtrl);
+ mdio_delay(EECtrl);
+ }
+ return;
+}
+
+/* Function: ns8382x_init
+ * Description: resets the ethernet controller chip and configures
+ * registers and data structures required for sending and receiving packets.
+ * Arguments: struct eth_device *dev: NIC data structure
+ * returns: int.
+ */
+
+static int
+ns8382x_init(struct eth_device *dev, bd_t * bis)
+{
+ u32 config;
+
+ ns8382x_reset(dev);
+
+ /* Disable PME:
+ * The PME bit is initialized from the EEPROM contents.
+ * PCI cards probably have PME disabled, but motherboard
+ * implementations may have PME set to enable WakeOnLan.
+ * With PME set the chip will scan incoming packets but
+ * nothing will be written to memory. */
+ OUTL(dev, SavedClkRun & ~0x100, ClkRun);
+
+ ns8382x_init_rxfilter(dev);
+ ns8382x_init_txd(dev);
+ ns8382x_init_rxd(dev);
+
+ /*set up ChipConfig */
+ config = INL(dev, ChipConfig);
+ /*turn off 64 bit ops && Ten-bit interface
+ * && big-endian mode && extended status */
+ config &= ~(TBIEn | Mode1000 | T64En | D64En | M64En | BEMode | PhyDis | ExtStEn);
+ OUTL(dev, config, ChipConfig);
+
+ /* Configure the PCI bus bursts and FIFO thresholds. */
+ tx_config = TxCarrierIgn | TxHeartIgn | TxAutoPad
+ | TxCollRetry | TxMxdma_1024 | (0x1002);
+ rx_config = RxMxdma_1024 | 0x20;
+#ifdef NS8382X_DEBUG
+ printf("%s: Setting TxConfig Register %#08X\n", dev->name, tx_config);
+ printf("%s: Setting RxConfig Register %#08X\n", dev->name, rx_config);
+#endif
+ OUTL(dev, tx_config, TxConfig);
+ OUTL(dev, rx_config, RxConfig);
+
+ /*turn off priority queueing */
+ OUTL(dev, 0x0, PriQueue);
+
+ ns8382x_check_duplex(dev);
+ ns8382x_set_rx_mode(dev);
+
+ OUTL(dev, (RxOn | TxOn), ChipCmd);
+ return 1;
+}
+
+/* Function: ns8382x_reset
+ * Description: soft resets the controller chip
+ * Arguments: struct eth_device *dev: NIC data structure
+ * Returns: void.
+ */
+static void
+ns8382x_reset(struct eth_device *dev)
+{
+ OUTL(dev, ChipReset, ChipCmd);
+ while (INL(dev, ChipCmd))
+ /*wait until done */ ;
+ OUTL(dev, 0, IntrMask);
+ OUTL(dev, 0, IntrEnable);
+}
+
+/* Function: ns8382x_init_rxfilter
+ * Description: sets receive filter address to our MAC address
+ * Arguments: struct eth_device *dev: NIC data structure
+ * returns: void.
+ */
+
+static void
+ns8382x_init_rxfilter(struct eth_device *dev)
+{
+ int i;
+
+ for (i = 0; i < ETH_ALEN; i += 2) {
+ OUTL(dev, i, RxFilterAddr);
+ OUTW(dev, dev->enetaddr[i] + (dev->enetaddr[i + 1] << 8),
+ RxFilterData);
+ }
+}
+
+/* Function: ns8382x_init_txd
+ * Description: initializes the Tx descriptor
+ * Arguments: struct eth_device *dev: NIC data structure
+ * returns: void.
+ */
+
+static void
+ns8382x_init_txd(struct eth_device *dev)
+{
+ txd.link = (u32) 0;
+ txd.bufptr = cpu_to_le32((u32) & txb[0]);
+ txd.cmdsts = (u32) 0;
+ txd.extsts = (u32) 0;
+
+ OUTL(dev, 0x0, TxRingPtrHi);
+ OUTL(dev, phys_to_bus((u32)&txd), TxRingPtr);
+#ifdef NS8382X_DEBUG
+ printf("ns8382x_init_txd: TX descriptor register loaded with: %#08X (&txd: %p)\n",
+ INL(dev, TxRingPtr), &txd);
+#endif
+}
+
+/* Function: ns8382x_init_rxd
+ * Description: initializes the Rx descriptor ring
+ * Arguments: struct eth_device *dev: NIC data structure
+ * Returns: void.
+ */
+
+static void
+ns8382x_init_rxd(struct eth_device *dev)
+{
+ int i;
+
+ OUTL(dev, 0x0, RxRingPtrHi);
+
+ cur_rx = 0;
+ for (i = 0; i < NUM_RX_DESC; i++) {
+ rxd[i].link =
+ cpu_to_le32((i + 1 <
+ NUM_RX_DESC) ? (u32) & rxd[i +
+ 1] : (u32) &
+ rxd[0]);
+ rxd[i].extsts = cpu_to_le32((u32) 0x0);
+ rxd[i].cmdsts = cpu_to_le32((u32) RX_BUF_SIZE);
+ rxd[i].bufptr = cpu_to_le32((u32) & rxb[i * RX_BUF_SIZE]);
+#ifdef NS8382X_DEBUG
+ printf
+ ("ns8382x_init_rxd: rxd[%d]=%p link=%X cmdsts=%X bufptr=%X\n",
+ i, &rxd[i], le32_to_cpu(rxd[i].link),
+ le32_to_cpu(rxd[i].cmdsts), le32_to_cpu(rxd[i].bufptr));
+#endif
+ }
+ OUTL(dev, phys_to_bus((u32) & rxd), RxRingPtr);
+
+#ifdef NS8382X_DEBUG
+ printf("ns8382x_init_rxd: RX descriptor register loaded with: %X\n",
+ INL(dev, RxRingPtr));
+#endif
+}
+
+/* Function: ns8382x_set_rx_mode
+ * Description:
+ * sets the receive mode to accept all broadcast packets and packets
+ * with our MAC address, and reject all multicast packets.
+ * Arguments: struct eth_device *dev: NIC data structure
+ * Returns: void.
+ */
+
+static void
+ns8382x_set_rx_mode(struct eth_device *dev)
+{
+ u32 rx_mode = 0x0;
+ /*spec says RxFilterEnable has to be 0 for rest of
+ * this stuff to be properly configured. Linux driver
+ * seems to support this*/
+/* OUTL(dev, rx_mode, RxFilterAddr);*/
+ rx_mode = (RxFilterEnable | AcceptAllBroadcast | AcceptPerfectMatch);
+ OUTL(dev, rx_mode, RxFilterAddr);
+ printf("ns8382x_set_rx_mode: set to %X\n", rx_mode);
+ /*now we turn RxFilterEnable back on */
+ /*rx_mode |= RxFilterEnable;
+ OUTL(dev, rx_mode, RxFilterAddr);*/
+}
+
+static void
+ns8382x_check_duplex(struct eth_device *dev)
+{
+ int gig = 0;
+ int hun = 0;
+ int duplex = 0;
+ int config = (INL(dev, ChipConfig) ^ SpeedStatus_Polarity);
+
+ duplex = (config & FullDuplex) ? 1 : 0;
+ gig = (config & GigSpeed) ? 1 : 0;
+ hun = (config & HundSpeed) ? 1 : 0;
+#ifdef NS8382X_DEBUG
+ printf("%s: Setting 10%s %s-duplex based on negotiated link"
+ " capability.\n", dev->name, (gig) ? "00" : (hun) ? "0" : "",
+ duplex ? "full" : "half");
+#endif
+ if (duplex) {
+ rx_config |= RxAcceptTx;
+ tx_config |= (TxCarrierIgn | TxHeartIgn);
+ } else {
+ rx_config &= ~RxAcceptTx;
+ tx_config &= ~(TxCarrierIgn | TxHeartIgn);
+ }
+#ifdef NS8382X_DEBUG
+ printf("%s: Resetting TxConfig Register %#08X\n", dev->name, tx_config);
+ printf("%s: Resetting RxConfig Register %#08X\n", dev->name, rx_config);
+#endif
+ OUTL(dev, tx_config, TxConfig);
+ OUTL(dev, rx_config, RxConfig);
+
+ /*if speed is 10 or 100, remove MODE1000,
+ * if it's 1000, then set it */
+ config = INL(dev, ChipConfig);
+ if (gig)
+ config |= Mode1000;
+ else
+ config &= ~Mode1000;
+
+#ifdef NS8382X_DEBUG
+ printf("%s: %setting Mode1000\n", dev->name, (gig) ? "S" : "Uns");
+#endif
+ OUTL(dev, config, ChipConfig);
+}
+
+/* Function: ns8382x_send
+ * Description: transmits a packet and waits for completion or timeout.
+ * Returns: void. */
+static int
+ns8382x_send(struct eth_device *dev, volatile void *packet, int length)
+{
+ u32 i, status = 0;
+ u32 tx_stat = 0;
+
+ /* Stop the transmitter */
+ OUTL(dev, TxOff, ChipCmd);
+#ifdef NS8382X_DEBUG
+ printf("ns8382x_send: sending %d bytes\n", (int)length);
+#endif
+
+ /* set the transmit buffer descriptor and enable Transmit State Machine */
+ txd.link = cpu_to_le32(0x0);
+ txd.bufptr = cpu_to_le32(phys_to_bus((u32)packet));
+ txd.extsts = cpu_to_le32(0x0);
+ txd.cmdsts = cpu_to_le32(DescOwn | length);
+
+ /* load Transmit Descriptor Register */
+ OUTL(dev, phys_to_bus((u32) & txd), TxRingPtr);
+#ifdef NS8382X_DEBUG
+ printf("ns8382x_send: TX descriptor register loaded with: %#08X\n",
+ INL(dev, TxRingPtr));
+ printf("\ttxd.link:%X\tbufp:%X\texsts:%X\tcmdsts:%X\n",
+ le32_to_cpu(txd.link), le32_to_cpu(txd.bufptr),
+ le32_to_cpu(txd.extsts), le32_to_cpu(txd.cmdsts));
+#endif
+ /* restart the transmitter */
+ OUTL(dev, TxOn, ChipCmd);
+
+ for (i = 0; ((vu_long)tx_stat = le32_to_cpu(txd.cmdsts)) & DescOwn; i++) {
+ if (i >= TOUT_LOOP) {
+ printf ("%s: tx error buffer not ready: txd.cmdsts %#X\n",
+ dev->name, tx_stat);
+ goto Done;
+ }
+ }
+
+ if (!(tx_stat & DescPktOK)) {
+ printf("ns8382x_send: Transmit error, Tx status %X.\n", tx_stat);
+ goto Done;
+ }
+#ifdef NS8382X_DEBUG
+ printf("ns8382x_send: tx_stat: %#08X\n", tx_stat);
+#endif
+
+ status = 1;
+ Done:
+ return status;
+}
+
+/* Function: ns8382x_poll
+ * Description: checks for a received packet and returns it if found.
+ * Arguments: struct eth_device *dev: NIC data structure
+ * Returns: 1 if packet was received.
+ * 0 if no packet was received.
+ * Side effects:
+ * Returns (copies) the packet to the array dev->packet.
+ * Returns the length of the packet.
+ */
+
+static int
+ns8382x_poll(struct eth_device *dev)
+{
+ int retstat = 0;
+ int length = 0;
+ vu_long rx_status = le32_to_cpu(rxd[cur_rx].cmdsts);
+
+ if (!(rx_status & (u32) DescOwn))
+ return retstat;
+#ifdef NS8382X_DEBUG
+ printf("ns8382x_poll: got a packet: cur_rx:%u, status:%lx\n",
+ cur_rx, rx_status);
+#endif
+ length = (rx_status & DSIZE) - CRC_SIZE;
+
+ if ((rx_status & (DescMore | DescPktOK | DescRxLong)) != DescPktOK) {
+ /* corrupted packet received */
+ printf("ns8382x_poll: Corrupted packet, status:%lx\n", rx_status);
+ retstat = 0;
+ } else {
+ /* give packet to higher level routine */
+ NetReceive((rxb + cur_rx * RX_BUF_SIZE), length);
+ retstat = 1;
+ }
+
+ /* return the descriptor and buffer to receive ring */
+ rxd[cur_rx].cmdsts = cpu_to_le32(RX_BUF_SIZE);
+ rxd[cur_rx].bufptr = cpu_to_le32((u32) & rxb[cur_rx * RX_BUF_SIZE]);
+
+ if (++cur_rx == NUM_RX_DESC)
+ cur_rx = 0;
+
+ /* re-enable the potentially idle receive state machine */
+ OUTL(dev, RxOn, ChipCmd);
+
+ return retstat;
+}
+
+/* Function: ns8382x_disable
+ * Description: Turns off interrupts and stops Tx and Rx engines
+ * Arguments: struct eth_device *dev: NIC data structure
+ * Returns: void.
+ */
+
+static void
+ns8382x_disable(struct eth_device *dev)
+{
+ /* Disable interrupts using the mask. */
+ OUTL(dev, 0, IntrMask);
+ OUTL(dev, 0, IntrEnable);
+
+ /* Stop the chip's Tx and Rx processes. */
+ OUTL(dev, (RxOff | TxOff), ChipCmd);
+
+ /* Restore PME enable bit */
+ OUTL(dev, SavedClkRun, ClkRun);
+}
+
+#endif