diff options
Diffstat (limited to 'drivers/net')
-rw-r--r-- | drivers/net/dc2114x.c | 4 | ||||
-rw-r--r-- | drivers/net/eepro100.c | 4 | ||||
-rw-r--r-- | drivers/net/macb.c | 4 | ||||
-rw-r--r-- | drivers/net/ne2000.c | 7 | ||||
-rw-r--r-- | drivers/net/pcnet.c | 4 | ||||
-rw-r--r-- | drivers/net/rtl8139.c | 4 | ||||
-rw-r--r-- | drivers/net/rtl8169.c | 103 | ||||
-rw-r--r-- | drivers/net/sk98lin/Makefile | 2 | ||||
-rw-r--r-- | drivers/net/tsec.c | 12 | ||||
-rw-r--r-- | drivers/net/tsi108_eth.c | 4 | ||||
-rw-r--r-- | drivers/net/uli526x.c | 6 |
11 files changed, 77 insertions, 77 deletions
diff --git a/drivers/net/dc2114x.c b/drivers/net/dc2114x.c index d5275dc..7238922 100644 --- a/drivers/net/dc2114x.c +++ b/drivers/net/dc2114x.c @@ -332,7 +332,7 @@ static int dc21x4x_init(struct eth_device* dev, bd_t* bis) if ((INL(dev, DE4X5_STS) & (STS_TS | STS_RS)) != 0) { printf("Error: Cannot reset ethernet controller.\n"); - return 0; + return -1; } #ifdef CONFIG_TULIP_SELECT_MEDIA @@ -382,7 +382,7 @@ static int dc21x4x_init(struct eth_device* dev, bd_t* bis) send_setup_frame(dev, bis); - return 1; + return 0; } static int dc21x4x_send(struct eth_device* dev, volatile void *packet, int length) diff --git a/drivers/net/eepro100.c b/drivers/net/eepro100.c index 738146e..96ed271 100644 --- a/drivers/net/eepro100.c +++ b/drivers/net/eepro100.c @@ -485,7 +485,7 @@ int eepro100_initialize (bd_t * bis) static int eepro100_init (struct eth_device *dev, bd_t * bis) { - int i, status = 0; + int i, status = -1; int tx_cur; struct descriptor *ias_cmd, *cfg_cmd; @@ -598,7 +598,7 @@ static int eepro100_init (struct eth_device *dev, bd_t * bis) goto Done; } - status = 1; + status = 0; Done: return status; diff --git a/drivers/net/macb.c b/drivers/net/macb.c index 95cdc49..6657d22 100644 --- a/drivers/net/macb.c +++ b/drivers/net/macb.c @@ -423,12 +423,12 @@ static int macb_init(struct eth_device *netdev, bd_t *bd) #endif if (!macb_phy_init(macb)) - return 0; + return -1; /* Enable TX and RX */ macb_writel(macb, NCR, MACB_BIT(TE) | MACB_BIT(RE)); - return 1; + return 0; } static void macb_halt(struct eth_device *netdev) diff --git a/drivers/net/ne2000.c b/drivers/net/ne2000.c index c978d62..b100657 100644 --- a/drivers/net/ne2000.c +++ b/drivers/net/ne2000.c @@ -839,7 +839,7 @@ void uboot_push_packet_len(int len) { } dp83902a_recv(&pbuf[0], len); - /*Just pass it to the upper layer*/ + /* Just pass it to the upper layer */ NetReceive(&pbuf[0], len); } @@ -902,7 +902,6 @@ int eth_init(bd_t *bd) { } void eth_halt() { - PRINTK("### eth_halt\n"); if(initialized) dp83902a_stop(); @@ -910,8 +909,8 @@ void eth_halt() { } int eth_rx() { -dp83902a_poll(); -return 1; + dp83902a_poll(); + return 1; } int eth_send(volatile void *packet, int length) { diff --git a/drivers/net/pcnet.c b/drivers/net/pcnet.c index 2af0e8f..4e270c9 100644 --- a/drivers/net/pcnet.c +++ b/drivers/net/pcnet.c @@ -402,7 +402,7 @@ static int pcnet_init(struct eth_device* dev, bd_t *bis) if (i <= 0) { printf("%s: TIMEOUT: controller init failed\n", dev->name); pcnet_reset (dev); - return 0; + return -1; } /* @@ -410,7 +410,7 @@ static int pcnet_init(struct eth_device* dev, bd_t *bis) */ pcnet_write_csr (dev, 0, 0x0002); - return 1; + return 0; } static int pcnet_send(struct eth_device* dev, volatile void *packet, int pkt_len) diff --git a/drivers/net/rtl8139.c b/drivers/net/rtl8139.c index 2367180..4c24805 100644 --- a/drivers/net/rtl8139.c +++ b/drivers/net/rtl8139.c @@ -273,10 +273,10 @@ static int rtl8139_probe(struct eth_device *dev, bd_t *bis) if (inb(ioaddr + MediaStatus) & MSRLinkFail) { printf("Cable not connected or other link failure\n"); - return(0); + return -1 ; } - return 1; + return 0; } /* Serial EEPROM section. */ diff --git a/drivers/net/rtl8169.c b/drivers/net/rtl8169.c index 63ea2cc..57ccbd9 100644 --- a/drivers/net/rtl8169.c +++ b/drivers/net/rtl8169.c @@ -48,7 +48,10 @@ * * Indent Options: indent -kr -i8 ***************************************************************************/ - +/* + * 26 August 2006 Mihai Georgian <u-boot@linuxnotincluded.org.uk> + * Modified to use le32_to_cpu and cpu_to_le32 properly + */ #include <common.h> #include <malloc.h> #include <net.h> @@ -68,12 +71,7 @@ static u32 ioaddr; /* Condensed operations for readability. */ -#define virt_to_le32desc(addr) cpu_to_le32(virt_to_bus(addr)) -#define le32desc_to_virt(addr) bus_to_virt(le32_to_cpu(addr)) - #define currticks() get_timer(0) -#define bus_to_phys(a) pci_mem_to_phys((pci_dev_t)dev->priv, a) -#define phys_to_bus(a) pci_phys_to_mem((pci_dev_t)dev->priv, a) /* media options */ #define MAX_UNITS 8 @@ -102,7 +100,7 @@ static int media[MAX_UNITS] = { -1, -1, -1, -1, -1, -1, -1, -1 }; #define RTL_MIN_IO_SIZE 0x80 #define TX_TIMEOUT (6*HZ) -/* write/read MMIO register */ +/* write/read MMIO register. Notice: {read,write}[wl] do the necessary swapping */ #define RTL_W8(reg, val8) writeb ((val8), ioaddr + (reg)) #define RTL_W16(reg, val16) writew ((val16), ioaddr + (reg)) #define RTL_W32(reg, val32) writel ((val32), ioaddr + (reg)) @@ -218,7 +216,7 @@ enum RTL8169_register_content { PHY_Enable_Auto_Nego = 0x1000, /* PHY_STAT_REG = 1; */ - PHY_Auto_Neco_Comp = 0x0020, + PHY_Auto_Nego_Comp = 0x0020, /* PHY_AUTO_NEGO_REG = 4; */ PHY_Cap_10_Half = 0x0020, @@ -413,23 +411,23 @@ static int rtl_recv(struct eth_device *dev) ioaddr = dev->iobase; cur_rx = tpc->cur_rx; - if ((tpc->RxDescArray[cur_rx].status & OWNbit) == 0) { - if (!(tpc->RxDescArray[cur_rx].status & RxRES)) { + if ((le32_to_cpu(tpc->RxDescArray[cur_rx].status) & OWNbit) == 0) { + if (!(le32_to_cpu(tpc->RxDescArray[cur_rx].status) & RxRES)) { unsigned char rxdata[RX_BUF_LEN]; - length = (int) (tpc->RxDescArray[cur_rx]. - status & 0x00001FFF) - 4; + length = (int) (le32_to_cpu(tpc->RxDescArray[cur_rx]. + status) & 0x00001FFF) - 4; memcpy(rxdata, tpc->RxBufferRing[cur_rx], length); NetReceive(rxdata, length); if (cur_rx == NUM_RX_DESC - 1) tpc->RxDescArray[cur_rx].status = - (OWNbit | EORbit) + RX_BUF_SIZE; + cpu_to_le32((OWNbit | EORbit) + RX_BUF_SIZE); else tpc->RxDescArray[cur_rx].status = - OWNbit + RX_BUF_SIZE; + cpu_to_le32(OWNbit + RX_BUF_SIZE); tpc->RxDescArray[cur_rx].buf_addr = - virt_to_bus(tpc->RxBufferRing[cur_rx]); + cpu_to_le32(tpc->RxBufferRing[cur_rx]); } else { puts("Error Rx"); } @@ -454,6 +452,7 @@ static int rtl_send(struct eth_device *dev, volatile void *packet, int length) u8 *ptxb; int entry = tpc->cur_tx % NUM_TX_DESC; u32 len = length; + int ret; #ifdef DEBUG_RTL8169_TX int stime = currticks(); @@ -470,34 +469,38 @@ static int rtl_send(struct eth_device *dev, volatile void *packet, int length) while (len < ETH_ZLEN) ptxb[len++] = '\0'; - tpc->TxDescArray[entry].buf_addr = virt_to_bus(ptxb); + tpc->TxDescArray[entry].buf_addr = cpu_to_le32(ptxb); if (entry != (NUM_TX_DESC - 1)) { tpc->TxDescArray[entry].status = - (OWNbit | FSbit | LSbit) | ((len > ETH_ZLEN) ? - len : ETH_ZLEN); + cpu_to_le32((OWNbit | FSbit | LSbit) | + ((len > ETH_ZLEN) ? len : ETH_ZLEN)); } else { tpc->TxDescArray[entry].status = - (OWNbit | EORbit | FSbit | LSbit) | - ((len > ETH_ZLEN) ? length : ETH_ZLEN); + cpu_to_le32((OWNbit | EORbit | FSbit | LSbit) | + ((len > ETH_ZLEN) ? len : ETH_ZLEN)); } RTL_W8(TxPoll, 0x40); /* set polling bit */ tpc->cur_tx++; to = currticks() + TX_TIMEOUT; - while ((tpc->TxDescArray[entry].status & OWNbit) && (currticks() < to)); /* wait */ + while ((le32_to_cpu(tpc->TxDescArray[entry].status) & OWNbit) + && (currticks() < to)); /* wait */ if (currticks() >= to) { #ifdef DEBUG_RTL8169_TX puts ("tx timeout/error\n"); printf ("%s elapsed time : %d\n", __FUNCTION__, currticks()-stime); #endif - return 0; + ret = 0; } else { #ifdef DEBUG_RTL8169_TX puts("tx done\n"); #endif - return length; + ret = length; } + /* Delay to make net console (nc) work properly */ + udelay(20); + return ret; } static void rtl8169_set_rx_mode(struct eth_device *dev) @@ -564,8 +567,8 @@ static void rtl8169_hw_start(struct eth_device *dev) tpc->cur_rx = 0; - RTL_W32(TxDescStartAddr, virt_to_le32desc(tpc->TxDescArray)); - RTL_W32(RxDescStartAddr, virt_to_le32desc(tpc->RxDescArray)); + RTL_W32(TxDescStartAddr, tpc->TxDescArray); + RTL_W32(RxDescStartAddr, tpc->RxDescArray); RTL_W8(Cfg9346, Cfg9346_Lock); udelay(10); @@ -603,13 +606,14 @@ static void rtl8169_init_ring(struct eth_device *dev) for (i = 0; i < NUM_RX_DESC; i++) { if (i == (NUM_RX_DESC - 1)) tpc->RxDescArray[i].status = - (OWNbit | EORbit) + RX_BUF_SIZE; + cpu_to_le32((OWNbit | EORbit) + RX_BUF_SIZE); else - tpc->RxDescArray[i].status = OWNbit + RX_BUF_SIZE; + tpc->RxDescArray[i].status = + cpu_to_le32(OWNbit + RX_BUF_SIZE); tpc->RxBufferRing[i] = &rxb[i * RX_BUF_SIZE]; tpc->RxDescArray[i].buf_addr = - virt_to_bus(tpc->RxBufferRing[i]); + cpu_to_le32(tpc->RxBufferRing[i]); } #ifdef DEBUG_RTL8169 @@ -620,11 +624,9 @@ static void rtl8169_init_ring(struct eth_device *dev) /************************************************************************** RESET - Finish setting up the ethernet interface ***************************************************************************/ -static void rtl_reset(struct eth_device *dev, bd_t *bis) +static int rtl_reset(struct eth_device *dev, bd_t *bis) { int i; - u8 diff; - u32 TxPhyAddr, RxPhyAddr; #ifdef DEBUG_RTL8169 int stime = currticks(); @@ -632,25 +634,14 @@ static void rtl_reset(struct eth_device *dev, bd_t *bis) #endif tpc->TxDescArrays = tx_ring; - if (tpc->TxDescArrays == 0) - puts("Allot Error"); /* Tx Desscriptor needs 256 bytes alignment; */ - TxPhyAddr = virt_to_bus(tpc->TxDescArrays); - diff = 256 - (TxPhyAddr - ((TxPhyAddr >> 8) << 8)); - TxPhyAddr += diff; - tpc->TxDescArray = (struct TxDesc *) (tpc->TxDescArrays + diff); + tpc->TxDescArray = (struct TxDesc *) ((unsigned long)(tpc->TxDescArrays + + 255) & ~255); tpc->RxDescArrays = rx_ring; /* Rx Desscriptor needs 256 bytes alignment; */ - RxPhyAddr = virt_to_bus(tpc->RxDescArrays); - diff = 256 - (RxPhyAddr - ((RxPhyAddr >> 8) << 8)); - RxPhyAddr += diff; - tpc->RxDescArray = (struct RxDesc *) (tpc->RxDescArrays + diff); - - if (tpc->TxDescArrays == NULL || tpc->RxDescArrays == NULL) { - puts("Allocate RxDescArray or TxDescArray failed\n"); - return; - } + tpc->RxDescArray = (struct RxDesc *) ((unsigned long)(tpc->RxDescArrays + + 255) & ~255); rtl8169_init_ring(dev); rtl8169_hw_start(dev); @@ -669,6 +660,7 @@ static void rtl_reset(struct eth_device *dev, bd_t *bis) #ifdef DEBUG_RTL8169 printf ("%s elapsed time : %d\n", __FUNCTION__, currticks()-stime); #endif + return 0; } /************************************************************************** @@ -733,7 +725,7 @@ static int rtl_init(struct eth_device *dev, bd_t *bis) /* Get MAC address. FIXME: read EEPROM */ for (i = 0; i < MAC_ADDR_LEN; i++) - dev->enetaddr[i] = RTL_R8(MAC0 + i); + bis->bi_enetaddr[i] = dev->enetaddr[i] = RTL_R8(MAC0 + i); #ifdef DEBUG_RTL8169 printf("MAC Address"); @@ -808,7 +800,7 @@ static int rtl_init(struct eth_device *dev, bd_t *bis) /* wait for auto-negotiation process */ for (i = 10000; i > 0; i--) { /* check if auto-negotiation complete */ - if (mdio_read(PHY_STAT_REG) & PHY_Auto_Neco_Comp) { + if (mdio_read(PHY_STAT_REG) & PHY_Auto_Nego_Comp) { udelay(100); option = RTL_R8(PHYstatus); if (option & _1000bpsF) { @@ -818,13 +810,12 @@ static int rtl_init(struct eth_device *dev, bd_t *bis) #endif } else { #ifdef DEBUG_RTL8169 - printf - ("%s: %sMbps %s-duplex operation.\n", - dev->name, - (option & _100bps) ? "100" : - "10", - (option & FullDup) ? "Full" : - "Half"); + printf("%s: %sMbps %s-duplex operation.\n", + dev->name, + (option & _100bps) ? "100" : + "10", + (option & FullDup) ? "Full" : + "Half"); #endif } break; @@ -869,7 +860,7 @@ int rtl8169_initialize(bd_t *bis) sprintf (dev->name, "RTL8169#%d", card_number); dev->priv = (void *) devno; - dev->iobase = (int)bus_to_phys(iobase); + dev->iobase = (int)pci_mem_to_phys(devno, iobase); dev->init = rtl_reset; dev->halt = rtl_halt; diff --git a/drivers/net/sk98lin/Makefile b/drivers/net/sk98lin/Makefile index a7d4a3b..8b83fae 100644 --- a/drivers/net/sk98lin/Makefile +++ b/drivers/net/sk98lin/Makefile @@ -20,7 +20,7 @@ # Foundation, Inc., 59 Temple Place, Suite 330, Boston, # MA 02111-1307 USA # -# File: drivers/sk98lin/Makefile +# File: drivers/net/sk98lin/Makefile # # Makefile for the SysKonnect SK-98xx device driver. # diff --git a/drivers/net/tsec.c b/drivers/net/tsec.c index ca6284b..25392f6 100644 --- a/drivers/net/tsec.c +++ b/drivers/net/tsec.c @@ -232,7 +232,7 @@ int tsec_init(struct eth_device *dev, bd_t * bd) startup_tsec(dev); /* If there's no link, fail */ - return priv->link; + return (priv->link ? 0 : -1); } @@ -674,6 +674,15 @@ uint mii_cis8204_setmode(uint mii_reg, struct tsec_private * priv) return MIIM_CIS8204_EPHYCON_INIT; } +uint mii_m88e1111s_setmode(uint mii_reg, struct tsec_private *priv) +{ + uint mii_data = read_phy_reg(priv, mii_reg); + + if (priv->flags & TSEC_REDUCED) + mii_data = (mii_data & 0xfff0) | 0x000b; + return mii_data; +} + /* Initialized required registers to appropriate values, zeroing * those we don't care about (unless zero is bad, in which case, * choose a more appropriate value) @@ -1034,6 +1043,7 @@ struct phy_info phy_info_M88E1111S = { (struct phy_cmd[]){ /* config */ /* Reset and configure the PHY */ {MIIM_CONTROL, MIIM_CONTROL_RESET, NULL}, + {0x1b, 0x848f, &mii_m88e1111s_setmode}, {0x14, 0x0cd2, NULL}, /* Delay RGMII TX and RX */ {MIIM_GBIT_CONTROL, MIIM_GBIT_CONTROL_INIT, NULL}, {MIIM_ANAR, MIIM_ANAR_INIT, NULL}, diff --git a/drivers/net/tsi108_eth.c b/drivers/net/tsi108_eth.c index 524e9da..a09115e 100644 --- a/drivers/net/tsi108_eth.c +++ b/drivers/net/tsi108_eth.c @@ -792,7 +792,7 @@ static int tsi108_eth_probe (struct eth_device *dev, bd_t * bis) (dev->enetaddr[0] << 16); if (marvell_88e_phy_config(dev, &speed, &duplex) == 0) - return 0; + return -1; value = MAC_CONFIG_2_PREAMBLE_LENGTH(7) | MAC_CONFIG_2_PAD_CRC | @@ -864,7 +864,7 @@ static int tsi108_eth_probe (struct eth_device *dev, bd_t * bis) /* enable TX queue */ reg_TX_CONTROL(base) = TX_CONTROL_GO | 0x01; - return 1; + return 0; } /* diff --git a/drivers/net/uli526x.c b/drivers/net/uli526x.c index 1267c57..8460f69 100644 --- a/drivers/net/uli526x.c +++ b/drivers/net/uli526x.c @@ -279,12 +279,12 @@ static int uli526x_init_one(struct eth_device *dev, bd_t *bis) db->desc_pool_ptr = (uchar *)&desc_pool_array[0]; db->desc_pool_dma_ptr = (dma_addr_t)&desc_pool_array[0]; if (db->desc_pool_ptr == NULL) - return 0; + return -1; db->buf_pool_ptr = &buf_pool[0]; db->buf_pool_dma_ptr = (dma_addr_t)&buf_pool[0]; if (db->buf_pool_ptr == NULL) - return 0; + return -1; db->first_tx_desc = (struct tx_desc *) db->desc_pool_ptr; db->first_tx_desc_dma = db->desc_pool_dma_ptr; @@ -331,7 +331,7 @@ static int uli526x_init_one(struct eth_device *dev, bd_t *bis) db->cr6_data |= ULI526X_TXTH_256; db->cr0_data = CR0_DEFAULT; uli526x_init(dev); - return 1; + return 0; } static void uli526x_disable(struct eth_device *dev) |