diff options
Diffstat (limited to 'drivers/net')
| -rw-r--r-- | drivers/net/bfin_mac.c | 284 | ||||
| -rw-r--r-- | drivers/net/bfin_mac.h | 25 |
2 files changed, 134 insertions, 175 deletions
diff --git a/drivers/net/bfin_mac.c b/drivers/net/bfin_mac.c index a620fcc..a622ca1 100644 --- a/drivers/net/bfin_mac.c +++ b/drivers/net/bfin_mac.c @@ -12,6 +12,8 @@ #include <netdev.h> #include <command.h> #include <malloc.h> +#include <miiphy.h> +#include <linux/mii.h> #include <asm/blackfin.h> #include <asm/mach-common/bits/dma.h> @@ -43,8 +45,6 @@ ADI_ETHER_BUFFER *rxbuf[PKTBUFSRX]; static u16 txIdx; /* index of the current RX buffer */ static u16 rxIdx; /* index of the current TX buffer */ -u16 PHYregs[NO_PHY_REGS]; /* u16 PHYADDR; */ - /* DMAx_CONFIG values at DMA Restart */ const ADI_DMA_CONFIG_REG rxdmacfg = { .b_DMA_EN = 1, /* enabled */ @@ -70,10 +70,38 @@ const ADI_DMA_CONFIG_REG txdmacfg = { .b_FLOW = 7 /* large desc flow */ }; +static int bfin_miiphy_wait(void) +{ + /* poll the STABUSY bit */ + while (bfin_read_EMAC_STAADD() & STABUSY) + continue; + return 0; +} + +static int bfin_miiphy_read(char *devname, uchar addr, uchar reg, ushort *val) +{ + if (bfin_miiphy_wait()) + return 1; + bfin_write_EMAC_STAADD(SET_PHYAD(addr) | SET_REGAD(reg) | STABUSY); + if (bfin_miiphy_wait()) + return 1; + *val = bfin_read_EMAC_STADAT(); + return 0; +} + +static int bfin_miiphy_write(char *devname, uchar addr, uchar reg, ushort val) +{ + if (bfin_miiphy_wait()) + return 1; + bfin_write_EMAC_STADAT(val); + bfin_write_EMAC_STAADD(SET_PHYAD(addr) | SET_REGAD(reg) | STAOP | STABUSY); + return 0; +} + int bfin_EMAC_initialize(bd_t *bis) { struct eth_device *dev; - dev = (struct eth_device *)malloc(sizeof(*dev)); + dev = malloc(sizeof(*dev)); if (dev == NULL) hang(); @@ -89,6 +117,10 @@ int bfin_EMAC_initialize(bd_t *bis) eth_register(dev); +#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII) + miiphy_register(dev->name, bfin_miiphy_read, bfin_miiphy_write); +#endif + return 0; } @@ -182,6 +214,100 @@ static int bfin_EMAC_recv(struct eth_device *dev) * *************************************************************/ +/* MDC = SCLK / MDC_freq / 2 - 1 */ +#define MDC_FREQ_TO_DIV(mdc_freq) (get_sclk() / (mdc_freq) / 2 - 1) + +static int bfin_miiphy_init(struct eth_device *dev, int *opmode) +{ + u16 phydat; + size_t count; + + /* Enable PHY output */ + *pVR_CTL |= CLKBUFOE; + + /* Set all the pins to peripheral mode */ +#ifdef CONFIG_BFIN_MAC_RMII + /* grab RMII pins */ +# if defined(__ADSPBF51x__) + *pPORTF_MUX = (*pPORTF_MUX & \ + ~(PORT_x_MUX_3_MASK | PORT_x_MUX_4_MASK | PORT_x_MUX_5_MASK)) | \ + PORT_x_MUX_3_FUNC_1 | PORT_x_MUX_4_FUNC_1 | PORT_x_MUX_5_FUNC_1; + *pPORTF_FER |= PF8 | PF9 | PF10 | PF11 | PF12 | PF13 | PF14 | PF15; + *pPORTG_MUX = (*pPORTG_MUX & ~PORT_x_MUX_0_MASK) | PORT_x_MUX_0_FUNC_1; + *pPORTG_FER |= PG0 | PG1 | PG2; +# elif defined(__ADSPBF52x__) + *pPORTG_MUX = (*pPORTG_MUX & ~PORT_x_MUX_6_MASK) | PORT_x_MUX_6_FUNC_2; + *pPORTG_FER |= PG14 | PG15; + *pPORTH_MUX = (*pPORTH_MUX & ~(PORT_x_MUX_0_MASK | PORT_x_MUX_1_MASK)) | \ + PORT_x_MUX_0_FUNC_2 | PORT_x_MUX_1_FUNC_2; + *pPORTH_FER |= PH0 | PH1 | PH2 | PH3 | PH4 | PH5 | PH6 | PH7 | PH8; +# else + *pPORTH_FER |= PH0 | PH1 | PH4 | PH5 | PH6 | PH8 | PH9 | PH14 | PH15; +# endif +#else + /* grab MII & RMII pins */ +# if defined(__ADSPBF51x__) + *pPORTF_MUX = (*pPORTF_MUX & \ + ~(PORT_x_MUX_0_MASK | PORT_x_MUX_1_MASK | PORT_x_MUX_3_MASK | PORT_x_MUX_4_MASK | PORT_x_MUX_5_MASK)) | \ + PORT_x_MUX_0_FUNC_1 | PORT_x_MUX_1_FUNC_1 | PORT_x_MUX_3_FUNC_1 | PORT_x_MUX_4_FUNC_1 | PORT_x_MUX_5_FUNC_1; + *pPORTF_FER |= PF0 | PF1 | PF2 | PF3 | PF4 | PF5 | PF6 | PF8 | PF9 | PF10 | PF11 | PF12 | PF13 | PF14 | PF15; + *pPORTG_MUX = (*pPORTG_MUX & ~PORT_x_MUX_0_MASK) | PORT_x_MUX_0_FUNC_1; + *pPORTG_FER |= PG0 | PG1 | PG2; +# elif defined(__ADSPBF52x__) + *pPORTG_MUX = (*pPORTG_MUX & ~PORT_x_MUX_6_MASK) | PORT_x_MUX_6_FUNC_2; + *pPORTG_FER |= PG14 | PG15; + *pPORTH_MUX = PORT_x_MUX_0_FUNC_2 | PORT_x_MUX_1_FUNC_2 | PORT_x_MUX_2_FUNC_2; + *pPORTH_FER = -1; /* all pins */ +# else + *pPORTH_FER = -1; /* all pins */ +# endif +#endif + + /* Odd word alignment for Receive Frame DMA word */ + /* Configure checksum support and rcve frame word alignment */ + bfin_write_EMAC_SYSCTL(RXDWA | RXCKS | SET_MDCDIV(MDC_FREQ_TO_DIV(2500000))); + + /* turn on auto-negotiation and wait for link to come up */ + bfin_miiphy_write(dev->name, PHYADDR, MII_BMCR, BMCR_ANENABLE); + count = 0; + while (1) { + ++count; + if (bfin_miiphy_read(dev->name, PHYADDR, MII_BMSR, &phydat)) + return -1; + if (phydat & BMSR_LSTATUS) + break; + if (count > 30000) { + printf("%s: link down, check cable\n", dev->name); + return -1; + } + udelay(100); + } + + /* see what kind of link we have */ + if (bfin_miiphy_read(dev->name, PHYADDR, MII_LPA, &phydat)) + return -1; + if (phydat & LPA_DUPLEX) + *opmode = FDMODE; + else + *opmode = 0; + + bfin_write_EMAC_MMC_CTL(RSTC | CROLL); + + /* Initialize the TX DMA channel registers */ + *pDMA2_X_COUNT = 0; + *pDMA2_X_MODIFY = 4; + *pDMA2_Y_COUNT = 0; + *pDMA2_Y_MODIFY = 0; + + /* Initialize the RX DMA channel registers */ + *pDMA1_X_COUNT = 0; + *pDMA1_X_MODIFY = 4; + *pDMA1_Y_COUNT = 0; + *pDMA1_Y_MODIFY = 0; + + return 0; +} + static int bfin_EMAC_init(struct eth_device *dev, bd_t *bd) { u32 opmode; @@ -192,14 +318,14 @@ static int bfin_EMAC_init(struct eth_device *dev, bd_t *bd) txIdx = 0; rxIdx = 0; -/* Initialize System Register */ - if (SetupSystemRegs(&dat) < 0) + /* Initialize System Register */ + if (bfin_miiphy_init(dev, &dat) < 0) return -1; -/* Initialize EMAC address */ + /* Initialize EMAC address */ bfin_EMAC_setup_addr(bd); -/* Initialize TX and RX buffer */ + /* Initialize TX and RX buffer */ for (i = 0; i < PKTBUFSRX; i++) { rxbuf[i] = SetupRxBuffer(i); if (i > 0) { @@ -226,7 +352,7 @@ static int bfin_EMAC_init(struct eth_device *dev, bd_t *bd) *pDMA1_CONFIG = *((u16 *) (void *)&rxbuf[0]->Dma[0].CONFIG); /* Wait MII done */ - PollMdcDone(); + bfin_miiphy_wait(); /* We enable only RX here */ /* ASTP : Enable Automatic Pad Stripping @@ -271,148 +397,6 @@ void bfin_EMAC_setup_addr(bd_t *bd) bd->bi_enetaddr[5] << 8; } -static void PollMdcDone(void) -{ - /* poll the STABUSY bit */ - while (*pEMAC_STAADD & STABUSY) ; -} - -static void WrPHYReg(u16 PHYAddr, u16 RegAddr, u16 Data) -{ - PollMdcDone(); - - *pEMAC_STADAT = Data; - - *pEMAC_STAADD = SET_PHYAD(PHYAddr) | SET_REGAD(RegAddr) | - STAOP | STAIE | STABUSY; -} - -/********************************************************************************* - * Read an off-chip register in a PHY through the MDC/MDIO port * - *********************************************************************************/ -static u16 RdPHYReg(u16 PHYAddr, u16 RegAddr) -{ - u16 Data; - - PollMdcDone(); - - *pEMAC_STAADD = SET_PHYAD(PHYAddr) | SET_REGAD(RegAddr) | - STAIE | STABUSY; - - PollMdcDone(); - - Data = (u16) * pEMAC_STADAT; - - PHYregs[RegAddr] = Data; /* save shadow copy */ - - return Data; -} - -#if 0 /* dead code ? */ -static void SoftResetPHY(void) -{ - u16 phydat; - /* set the reset bit */ - WrPHYReg(PHYADDR, PHY_MODECTL, PHY_RESET); - /* and clear it again */ - WrPHYReg(PHYADDR, PHY_MODECTL, 0x0000); - do { - /* poll until reset is complete */ - phydat = RdPHYReg(PHYADDR, PHY_MODECTL); - } while ((phydat & PHY_RESET) != 0); -} -#endif - -/* MDC = SCLK / MDC_freq / 2 - 1 */ -#define MDC_FREQ_TO_DIV(mdc_freq) (get_sclk() / (mdc_freq) / 2 - 1) - -static int SetupSystemRegs(int *opmode) -{ - u16 phydat; - int count = 0; - /* Enable PHY output */ - *pVR_CTL |= CLKBUFOE; - /* Set all the pins to peripheral mode */ - -#ifdef CONFIG_BFIN_MAC_RMII - /* grab RMII pins */ -# if defined(__ADSPBF51x__) - *pPORTF_MUX = (*pPORTF_MUX & \ - ~(PORT_x_MUX_3_MASK | PORT_x_MUX_4_MASK | PORT_x_MUX_5_MASK)) | \ - PORT_x_MUX_3_FUNC_1 | PORT_x_MUX_4_FUNC_1 | PORT_x_MUX_5_FUNC_1; - *pPORTF_FER |= PF8 | PF9 | PF10 | PF11 | PF12 | PF13 | PF14 | PF15; - *pPORTG_MUX = (*pPORTG_MUX & ~PORT_x_MUX_0_MASK) | PORT_x_MUX_0_FUNC_1; - *pPORTG_FER |= PG0 | PG1 | PG2; -# elif defined(__ADSPBF52x__) - *pPORTG_MUX = (*pPORTG_MUX & ~PORT_x_MUX_6_MASK) | PORT_x_MUX_6_FUNC_2; - *pPORTG_FER |= PG14 | PG15; - *pPORTH_MUX = (*pPORTH_MUX & ~(PORT_x_MUX_0_MASK | PORT_x_MUX_1_MASK)) | \ - PORT_x_MUX_0_FUNC_2 | PORT_x_MUX_1_FUNC_2; - *pPORTH_FER |= PH0 | PH1 | PH2 | PH3 | PH4 | PH5 | PH6 | PH7 | PH8; -# else - *pPORTH_FER |= PH0 | PH1 | PH4 | PH5 | PH6 | PH8 | PH9 | PH14 | PH15; -# endif -#else - /* grab MII & RMII pins */ -# if defined(__ADSPBF51x__) - *pPORTF_MUX = (*pPORTF_MUX & \ - ~(PORT_x_MUX_0_MASK | PORT_x_MUX_1_MASK | PORT_x_MUX_3_MASK | PORT_x_MUX_4_MASK | PORT_x_MUX_5_MASK)) | \ - PORT_x_MUX_0_FUNC_1 | PORT_x_MUX_1_FUNC_1 | PORT_x_MUX_3_FUNC_1 | PORT_x_MUX_4_FUNC_1 | PORT_x_MUX_5_FUNC_1; - *pPORTF_FER |= PF0 | PF1 | PF2 | PF3 | PF4 | PF5 | PF6 | PF8 | PF9 | PF10 | PF11 | PF12 | PF13 | PF14 | PF15; - *pPORTG_MUX = (*pPORTG_MUX & ~PORT_x_MUX_0_MASK) | PORT_x_MUX_0_FUNC_1; - *pPORTG_FER |= PG0 | PG1 | PG2; -# elif defined(__ADSPBF52x__) - *pPORTG_MUX = (*pPORTG_MUX & ~PORT_x_MUX_6_MASK) | PORT_x_MUX_6_FUNC_2; - *pPORTG_FER |= PG14 | PG15; - *pPORTH_MUX = PORT_x_MUX_0_FUNC_2 | PORT_x_MUX_1_FUNC_2 | PORT_x_MUX_2_FUNC_2; - *pPORTH_FER = -1; /* all pins */ -# else - *pPORTH_FER = -1; /* all pins */ -# endif -#endif - - /* Odd word alignment for Receive Frame DMA word */ - /* Configure checksum support and rcve frame word alignment */ - *pEMAC_SYSCTL = RXDWA | RXCKS | SET_MDCDIV(MDC_FREQ_TO_DIV(2500000)); - /* auto negotiation on */ - /* full duplex */ - /* 100 Mbps */ - phydat = PHY_ANEG_EN | PHY_DUPLEX | PHY_SPD_SET; - WrPHYReg(PHYADDR, PHY_MODECTL, phydat); - do { - udelay(1000); - phydat = RdPHYReg(PHYADDR, PHY_MODESTAT); - if (count > 3000) { - printf - ("Link is down, please check your network connection\n"); - return -1; - } - count++; - } while (!(phydat & 0x0004)); - - phydat = RdPHYReg(PHYADDR, PHY_ANLPAR); - - if ((phydat & 0x0100) || (phydat & 0x0040)) - *opmode = FDMODE; - else - *opmode = 0; - - *pEMAC_MMC_CTL = RSTC | CROLL; - - /* Initialize the TX DMA channel registers */ - *pDMA2_X_COUNT = 0; - *pDMA2_X_MODIFY = 4; - *pDMA2_Y_COUNT = 0; - *pDMA2_Y_MODIFY = 0; - - /* Initialize the RX DMA channel registers */ - *pDMA1_X_COUNT = 0; - *pDMA1_X_MODIFY = 4; - *pDMA1_Y_COUNT = 0; - *pDMA1_Y_MODIFY = 0; - return 0; -} - ADI_ETHER_BUFFER *SetupRxBuffer(int no) { ADI_ETHER_FRAME_BUFFER *frmbuf; diff --git a/drivers/net/bfin_mac.h b/drivers/net/bfin_mac.h index c8a94d0..c41b4d4 100644 --- a/drivers/net/bfin_mac.h +++ b/drivers/net/bfin_mac.h @@ -10,28 +10,8 @@ #define __BFIN_MAC_H__ #define PHYADDR 0x01 -#define NO_PHY_REGS 0x20 - -#define DEFAULT_PHY_PHYID1 0x0007 -#define DEFAULT_PHY_PHYID2 0xC0A3 -#define PHY_MODECTL 0x00 -#define PHY_MODESTAT 0x01 -#define PHY_PHYID1 0x02 -#define PHY_PHYID2 0x03 -#define PHY_ANAR 0x04 -#define PHY_ANLPAR 0x05 -#define PHY_ANER 0x06 - -#define PHY_RESET 0x8000 -#define PHY_ANEG_EN 0x1000 -#define PHY_DUPLEX 0x0100 -#define PHY_SPD_SET 0x2000 - #define RECV_BUFSIZE (0x614) -typedef volatile u32 reg32; -typedef volatile u16 reg16; - typedef struct ADI_DMA_CONFIG_REG { u16 b_DMA_EN:1; /* 0 Enabled */ u16 b_WNR:1; /* 1 Direction */ @@ -79,11 +59,6 @@ static void bfin_EMAC_halt(struct eth_device *dev); static int bfin_EMAC_send(struct eth_device *dev, volatile void *packet, int length); static int bfin_EMAC_recv(struct eth_device *dev); -static void PollMdcDone(void); -static void WrPHYReg(u16 PHYAddr, u16 RegAddr, u16 Data); -static u16 RdPHYReg(u16 PHYAddr, u16 RegAddr); -static int SetupSystemRegs(int *opmode); - static void bfin_EMAC_setup_addr(bd_t *bd); #endif |