diff options
Diffstat (limited to 'drivers/net/npe/include/IxEthMii.h')
| -rw-r--r-- | drivers/net/npe/include/IxEthMii.h | 270 |
1 files changed, 270 insertions, 0 deletions
diff --git a/drivers/net/npe/include/IxEthMii.h b/drivers/net/npe/include/IxEthMii.h new file mode 100644 index 0000000..397253a --- /dev/null +++ b/drivers/net/npe/include/IxEthMii.h @@ -0,0 +1,270 @@ +/** + * @file IxEthMii.h + * + * @brief this file contains the public API of @ref IxEthMii component + * + * Design notes : + * The main intent of this API is to inplement MII high level fonctionalitoes + * to support the codelets provided with the IXP400 software releases. It + * superceedes previous interfaces provided with @ref IxEThAcc component. + * + * This API has been tested with the PHYs provided with the + * IXP400 development platforms. It may not work for specific Ethernet PHYs + * used on specific boards. + * + * This source code detects and interface the LXT972, LXT973 and KS6995 + * Ethernet PHYs. + * + * This source code should be considered as an example which may need + * to be adapted for different hardware implementations. + * + * It is strongly recommended to use public domain and GPL utilities + * like libmii, mii-diag for MII interface support. + * + * + * + * @par + * IXP400 SW Release version 2.0 + * + * -- Copyright Notice -- + * + * @par + * Copyright 2001-2005, Intel Corporation. + * All rights reserved. + * + * @par + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * 3. Neither the name of the Intel Corporation nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * @par + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS ``AS IS'' + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY + * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF + * SUCH DAMAGE. + * + * @par + * -- End of Copyright Notice -- + */ + +#ifndef IxEthMii_H +#define IxEthMii_H + +#include <IxTypes.h> + +/** + * @defgroup IxEthMii IXP400 Ethernet Phy Access (IxEthMii) API + * + * @brief ethMii is a library that does provides access to the + * Ethernet PHYs + * + *@{ + */ + +/** + * @ingroup IxEthMii + * + * @fn ixEthMiiPhyScan(BOOL phyPresent[], UINT32 maxPhyCount) + * + * @brief Scan the MDIO bus for PHYs + * This function scans PHY addresses 0 through 31, and sets phyPresent[n] to + * TRUE if a phy is discovered at address n. + * + * - Reentrant - no + * - ISR Callable - no + * + * @pre The MAC on Ethernet Port 2 (NPE C) must be initialised, and generating the MDIO clock. + * + * @param phyPresent BOOL [in] - boolean array of IXP425_ETH_ACC_MII_MAX_ADDR entries + * @param maxPhyCount UINT32 [in] - number of PHYs to search for (the scan will stop when + * the indicated number of PHYs is found). + * + * @return IX_STATUS + * - IX_ETH_ACC_SUCCESS + * - IX_ETH_ACC_FAIL : invalid arguments. + * + * <hr> + */ +PUBLIC IX_STATUS ixEthMiiPhyScan(BOOL phyPresent[], UINT32 maxPhyCount); + +/** + * @ingroup IxEthMii + * + * @fn ixEthMiiPhyConfig(UINT32 phyAddr, + BOOL speed100, + BOOL fullDuplex, + BOOL autonegotiate) + * + * + * @brief Configure a PHY + * Configure a PHY's speed, duplex and autonegotiation status + * + * - Reentrant - no + * - ISR Callable - no + * + * @pre The MAC on Ethernet Port 2 (NPE C) must be initialised, and generating the MDIO clock. + * + * @param phyAddr UINT32 [in] + * @param speed100 BOOL [in] - set to TRUE for 100Mbit/s operation, FALSE for 10Mbit/s + * @param fullDuplex BOOL [in] - set to TRUE for Full Duplex, FALSE for Half Duplex + * @param autonegotiate BOOL [in] - set to TRUE to enable autonegotiation + * + * @return IX_STATUS + * - IX_SUCCESS + * - IX_FAIL : invalid arguments. + * + * <hr> + */ +PUBLIC IX_STATUS ixEthMiiPhyConfig(UINT32 phyAddr, + BOOL speed100, + BOOL fullDuplex, + BOOL autonegotiate); + +/** + * @ingroup IxEthMii + * + * @fn ixEthMiiPhyLoopbackEnable(UINT32 phyAddr) + * + * + * @brief Enable PHY Loopback in a specific Eth MII port + * + * @note When PHY Loopback is enabled, frames sent out to the PHY from the + * IXP400 will be looped back to the IXP400. They will not be transmitted out + * on the wire. + * + * - Reentrant - no + * - ISR Callable - no + * + * @param phyAddr UINT32 [in] - the address of the Ethernet PHY (0-31) + * + * @return IX_STATUS + * - IX_SUCCESS + * - IX_FAIL : invalid arguments. + * <hr> + */ +PUBLIC IX_STATUS +ixEthMiiPhyLoopbackEnable (UINT32 phyAddr); + +/** + * @ingroup IxEthMii + * + * @fn ixEthMiiPhyLoopbackDisable(UINT32 phyAddr) + * + * + * @brief Disable PHY Loopback in a specific Eth MII port + * + * - Reentrant - no + * - ISR Callable - no + * + * @param phyAddr UINT32 [in] - the address of the Ethernet PHY (0-31) + * + * @return IX_STATUS + * - IX_SUCCESS + * - IX_FAIL : invalid arguments. + * <hr> + */ +PUBLIC IX_STATUS +ixEthMiiPhyLoopbackDisable (UINT32 phyAddr); + +/** + * @ingroup IxEthMii + * + * @fn ixEthMiiPhyReset(UINT32 phyAddr) + * + * @brief Reset a PHY + * Reset a PHY + * + * - Reentrant - no + * - ISR Callable - no + * + * @pre The MAC on Ethernet Port 2 (NPE C) must be initialised, and generating the MDIO clock. + * + * @param phyAddr UINT32 [in] - the address of the Ethernet PHY (0-31) + * + * @return IX_STATUS + * - IX_SUCCESS + * - IX_FAIL : invalid arguments. + * + * <hr> + */ +PUBLIC IX_STATUS ixEthMiiPhyReset(UINT32 phyAddr); + + +/** + * @ingroup IxEthMii + * + * @fn ixEthMiiLinkStatus(UINT32 phyAddr, + BOOL *linkUp, + BOOL *speed100, + BOOL *fullDuplex, + BOOL *autoneg) + * + * @brief Retrieve the current status of a PHY + * Retrieve the link, speed, duplex and autonegotiation status of a PHY + * + * - Reentrant - no + * - ISR Callable - no + * + * @pre The MAC on Ethernet Port 2 (NPE C) must be initialised, and generating the MDIO clock. + * + * @param phyAddr UINT32 [in] - the address of the Ethernet PHY (0-31) + * @param linkUp BOOL [out] - set to TRUE if the link is up + * @param speed100 BOOL [out] - set to TRUE indicates 100Mbit/s, FALSE indicates 10Mbit/s + * @param fullDuplex BOOL [out] - set to TRUE indicates Full Duplex, FALSE indicates Half Duplex + * @param autoneg BOOL [out] - set to TRUE indicates autonegotiation is enabled, FALSE indicates autonegotiation is disabled + * + * @return IX_STATUS + * - IX_SUCCESS + * - IX_FAIL : invalid arguments. + * + * <hr> + */ +PUBLIC IX_STATUS ixEthMiiLinkStatus(UINT32 phyAddr, + BOOL *linkUp, + BOOL *speed100, + BOOL *fullDuplex, + BOOL *autoneg); + +/** + * @ingroup IxEthMii + * + * @fn ixEthMiiPhyShow (UINT32 phyAddr) + * + * + * @brief Display information on a specified PHY + * Display link status, speed, duplex and Auto Negotiation status + * + * - Reentrant - no + * - ISR Callable - no + * + * @pre The MAC on Ethernet Port 2 (NPE C) must be initialised, and generating the MDIO clock. + * + * @param phyAddr UINT32 [in] - the address of the Ethernet PHY (0-31) + * + * @return IX_STATUS + * - IX_SUCCESS + * - IX_FAIL : invalid arguments. + * + * <hr> + */ +PUBLIC IX_STATUS ixEthMiiPhyShow (UINT32 phyAddr); + +#endif /* ndef IxEthMii_H */ +/** + *@} + */ |