diff options
Diffstat (limited to 'drivers/mtd')
| -rw-r--r-- | drivers/mtd/nand/atmel_nand.c | 208 | ||||
| -rw-r--r-- | drivers/mtd/nand/ndfc.c | 13 | ||||
| -rw-r--r-- | drivers/mtd/nand/omap_elm.c | 6 | ||||
| -rw-r--r-- | drivers/mtd/nand/omap_gpmc.c | 572 | ||||
| -rw-r--r-- | drivers/mtd/spi/sf_ops.c | 8 | ||||
| -rw-r--r-- | drivers/mtd/spi/sf_params.c | 5 | ||||
| -rw-r--r-- | drivers/mtd/spi/sf_probe.c | 19 |
7 files changed, 419 insertions, 412 deletions
diff --git a/drivers/mtd/nand/atmel_nand.c b/drivers/mtd/nand/atmel_nand.c index 05ddfbb..e1fc48f 100644 --- a/drivers/mtd/nand/atmel_nand.c +++ b/drivers/mtd/nand/atmel_nand.c @@ -31,6 +31,10 @@ #ifdef CONFIG_ATMEL_NAND_HW_PMECC +#ifdef CONFIG_SPL_BUILD +#undef CONFIG_SYS_NAND_ONFI_DETECTION +#endif + struct atmel_nand_host { struct pmecc_regs __iomem *pmecc; struct pmecc_errloc_regs __iomem *pmerrloc; @@ -1169,6 +1173,209 @@ static int at91_nand_ready(struct mtd_info *mtd) } #endif +#ifdef CONFIG_SPL_BUILD +/* The following code is for SPL */ +static nand_info_t mtd; +static struct nand_chip nand_chip; + +static int nand_command(int block, int page, uint32_t offs, u8 cmd) +{ + struct nand_chip *this = mtd.priv; + int page_addr = page + block * CONFIG_SYS_NAND_PAGE_COUNT; + void (*hwctrl)(struct mtd_info *mtd, int cmd, + unsigned int ctrl) = this->cmd_ctrl; + + while (this->dev_ready(&mtd)) + ; + + if (cmd == NAND_CMD_READOOB) { + offs += CONFIG_SYS_NAND_PAGE_SIZE; + cmd = NAND_CMD_READ0; + } + + hwctrl(&mtd, cmd, NAND_CTRL_CLE | NAND_CTRL_CHANGE); + + if (this->options & NAND_BUSWIDTH_16) + offs >>= 1; + + hwctrl(&mtd, offs & 0xff, NAND_CTRL_ALE | NAND_CTRL_CHANGE); + hwctrl(&mtd, (offs >> 8) & 0xff, NAND_CTRL_ALE); + hwctrl(&mtd, (page_addr & 0xff), NAND_CTRL_ALE); + hwctrl(&mtd, ((page_addr >> 8) & 0xff), NAND_CTRL_ALE); +#ifdef CONFIG_SYS_NAND_5_ADDR_CYCLE + hwctrl(&mtd, (page_addr >> 16) & 0x0f, NAND_CTRL_ALE); +#endif + hwctrl(&mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE); + + hwctrl(&mtd, NAND_CMD_READSTART, NAND_CTRL_CLE | NAND_CTRL_CHANGE); + hwctrl(&mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE); + + while (this->dev_ready(&mtd)) + ; + + return 0; +} + +static int nand_is_bad_block(int block) +{ + struct nand_chip *this = mtd.priv; + + nand_command(block, 0, CONFIG_SYS_NAND_BAD_BLOCK_POS, NAND_CMD_READOOB); + + if (this->options & NAND_BUSWIDTH_16) { + if (readw(this->IO_ADDR_R) != 0xffff) + return 1; + } else { + if (readb(this->IO_ADDR_R) != 0xff) + return 1; + } + + return 0; +} + +#ifdef CONFIG_SPL_NAND_ECC +static int nand_ecc_pos[] = CONFIG_SYS_NAND_ECCPOS; +#define ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / \ + CONFIG_SYS_NAND_ECCSIZE) +#define ECCTOTAL (ECCSTEPS * CONFIG_SYS_NAND_ECCBYTES) + +static int nand_read_page(int block, int page, void *dst) +{ + struct nand_chip *this = mtd.priv; + u_char ecc_calc[ECCTOTAL]; + u_char ecc_code[ECCTOTAL]; + u_char oob_data[CONFIG_SYS_NAND_OOBSIZE]; + int eccsize = CONFIG_SYS_NAND_ECCSIZE; + int eccbytes = CONFIG_SYS_NAND_ECCBYTES; + int eccsteps = ECCSTEPS; + int i; + uint8_t *p = dst; + nand_command(block, page, 0, NAND_CMD_READ0); + + for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { + if (this->ecc.mode != NAND_ECC_SOFT) + this->ecc.hwctl(&mtd, NAND_ECC_READ); + this->read_buf(&mtd, p, eccsize); + this->ecc.calculate(&mtd, p, &ecc_calc[i]); + } + this->read_buf(&mtd, oob_data, CONFIG_SYS_NAND_OOBSIZE); + + for (i = 0; i < ECCTOTAL; i++) + ecc_code[i] = oob_data[nand_ecc_pos[i]]; + + eccsteps = ECCSTEPS; + p = dst; + + for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) + this->ecc.correct(&mtd, p, &ecc_code[i], &ecc_calc[i]); + + return 0; +} +#else +static int nand_read_page(int block, int page, void *dst) +{ + struct nand_chip *this = mtd.priv; + + nand_command(block, page, 0, NAND_CMD_READ0); + atmel_nand_pmecc_read_page(&mtd, this, dst, 0, page); + + return 0; +} +#endif /* CONFIG_SPL_NAND_ECC */ + +int nand_spl_load_image(uint32_t offs, unsigned int size, void *dst) +{ + unsigned int block, lastblock; + unsigned int page; + + block = offs / CONFIG_SYS_NAND_BLOCK_SIZE; + lastblock = (offs + size - 1) / CONFIG_SYS_NAND_BLOCK_SIZE; + page = (offs % CONFIG_SYS_NAND_BLOCK_SIZE) / CONFIG_SYS_NAND_PAGE_SIZE; + + while (block <= lastblock) { + if (!nand_is_bad_block(block)) { + while (page < CONFIG_SYS_NAND_PAGE_COUNT) { + nand_read_page(block, page, dst); + dst += CONFIG_SYS_NAND_PAGE_SIZE; + page++; + } + + page = 0; + } else { + lastblock++; + } + + block++; + } + + return 0; +} + +int at91_nand_wait_ready(struct mtd_info *mtd) +{ + struct nand_chip *this = mtd->priv; + + udelay(this->chip_delay); + + return 0; +} + +int board_nand_init(struct nand_chip *nand) +{ + int ret = 0; + + nand->ecc.mode = NAND_ECC_SOFT; +#ifdef CONFIG_SYS_NAND_DBW_16 + nand->options = NAND_BUSWIDTH_16; + nand->read_buf = nand_read_buf16; +#else + nand->read_buf = nand_read_buf; +#endif + nand->cmd_ctrl = at91_nand_hwcontrol; +#ifdef CONFIG_SYS_NAND_READY_PIN + nand->dev_ready = at91_nand_ready; +#else + nand->dev_ready = at91_nand_wait_ready; +#endif + nand->chip_delay = 20; + +#ifdef CONFIG_ATMEL_NAND_HWECC +#ifdef CONFIG_ATMEL_NAND_HW_PMECC + ret = atmel_pmecc_nand_init_params(nand, &mtd); +#endif +#endif + + return ret; +} + +void nand_init(void) +{ + mtd.writesize = CONFIG_SYS_NAND_PAGE_SIZE; + mtd.oobsize = CONFIG_SYS_NAND_OOBSIZE; + mtd.priv = &nand_chip; + nand_chip.IO_ADDR_R = (void __iomem *)CONFIG_SYS_NAND_BASE; + nand_chip.IO_ADDR_W = (void __iomem *)CONFIG_SYS_NAND_BASE; + board_nand_init(&nand_chip); + +#ifdef CONFIG_SPL_NAND_ECC + if (nand_chip.ecc.mode == NAND_ECC_SOFT) { + nand_chip.ecc.calculate = nand_calculate_ecc; + nand_chip.ecc.correct = nand_correct_data; + } +#endif + + if (nand_chip.select_chip) + nand_chip.select_chip(&mtd, 0); +} + +void nand_deselect(void) +{ + if (nand_chip.select_chip) + nand_chip.select_chip(&mtd, -1); +} + +#else + #ifndef CONFIG_SYS_NAND_BASE_LIST #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } #endif @@ -1227,3 +1434,4 @@ void board_nand_init(void) dev_err(host->dev, "atmel_nand: Fail to initialize #%d chip", i); } +#endif /* CONFIG_SPL_BUILD */ diff --git a/drivers/mtd/nand/ndfc.c b/drivers/mtd/nand/ndfc.c index 34688e9..5510b13 100644 --- a/drivers/mtd/nand/ndfc.c +++ b/drivers/mtd/nand/ndfc.c @@ -104,7 +104,6 @@ static void ndfc_read_buf(struct mtd_info *mtdinfo, uint8_t *buf, int len) *p++ = in_be32((u32 *)(base + NDFC_DATA)); } -#ifndef CONFIG_NAND_SPL /* * Don't use these speedup functions in NAND boot image, since the image * has to fit into 4kByte. @@ -148,8 +147,6 @@ static uint8_t ndfc_read_byte(struct mtd_info *mtd) } -#endif /* #ifndef CONFIG_NAND_SPL */ - void board_nand_select_device(struct nand_chip *nand, int chip) { /* @@ -207,21 +204,11 @@ int board_nand_init(struct nand_chip *nand) nand->options |= NAND_BUSWIDTH_16; #endif -#ifndef CONFIG_NAND_SPL nand->write_buf = ndfc_write_buf; nand->verify_buf = ndfc_verify_buf; nand->read_byte = ndfc_read_byte; chip++; -#else - /* - * Setup EBC (CS0 only right now) - */ - mtebc(EBC0_CFG, CONFIG_SYS_NDFC_EBC0_CFG); - - mtebc(PB0CR, CONFIG_SYS_EBC_PB0CR); - mtebc(PB0AP, CONFIG_SYS_EBC_PB0AP); -#endif return 0; } diff --git a/drivers/mtd/nand/omap_elm.c b/drivers/mtd/nand/omap_elm.c index 2aa7807..47b1f1b 100644 --- a/drivers/mtd/nand/omap_elm.c +++ b/drivers/mtd/nand/omap_elm.c @@ -16,9 +16,9 @@ #include <common.h> #include <asm/io.h> #include <asm/errno.h> -#include <asm/arch/cpu.h> -#include <asm/omap_gpmc.h> -#include <asm/omap_elm.h> +#include <linux/mtd/omap_gpmc.h> +#include <linux/mtd/omap_elm.h> +#include <asm/arch/hardware.h> #define ELM_DEFAULT_POLY (0) diff --git a/drivers/mtd/nand/omap_gpmc.c b/drivers/mtd/nand/omap_gpmc.c index 389c4de..881a636 100644 --- a/drivers/mtd/nand/omap_gpmc.c +++ b/drivers/mtd/nand/omap_gpmc.c @@ -9,17 +9,24 @@ #include <asm/io.h> #include <asm/errno.h> #include <asm/arch/mem.h> -#include <asm/arch/cpu.h> -#include <asm/omap_gpmc.h> +#include <linux/mtd/omap_gpmc.h> #include <linux/mtd/nand_ecc.h> #include <linux/bch.h> #include <linux/compiler.h> #include <nand.h> -#include <asm/omap_elm.h> +#include <linux/mtd/omap_elm.h> #define BADBLOCK_MARKER_LENGTH 2 #define SECTOR_BYTES 512 +#define ECCCLEAR (0x1 << 8) +#define ECCRESULTREG1 (0x1 << 0) +/* 4 bit padding to make byte aligned, 56 = 52 + 4 */ +#define BCH4_BIT_PAD 4 +#ifdef CONFIG_BCH +static u8 bch8_polynomial[] = {0xef, 0x51, 0x2e, 0x09, 0xed, 0x93, 0x9a, 0xc2, + 0x97, 0x79, 0xe5, 0x24, 0xb5}; +#endif static uint8_t cs; static __maybe_unused struct nand_ecclayout omap_ecclayout; @@ -60,21 +67,6 @@ int omap_spl_dev_ready(struct mtd_info *mtd) } #endif -/* - * omap_hwecc_init - Initialize the Hardware ECC for NAND flash in - * GPMC controller - * @mtd: MTD device structure - * - */ -static void __maybe_unused omap_hwecc_init(struct nand_chip *chip) -{ - /* - * Init ECC Control Register - * Clear all ECC | Enable Reg1 - */ - writel(ECCCLEAR | ECCRESULTREG1, &gpmc_cfg->ecc_control); - writel(ECCSIZE1 | ECCSIZE0 | ECCSIZE0SEL, &gpmc_cfg->ecc_size_config); -} /* * gen_true_ecc - This function will generate true ECC value, which @@ -156,74 +148,6 @@ static int __maybe_unused omap_correct_data(struct mtd_info *mtd, uint8_t *dat, } /* - * omap_calculate_ecc - Generate non-inverted ECC bytes. - * - * Using noninverted ECC can be considered ugly since writing a blank - * page ie. padding will clear the ECC bytes. This is no problem as - * long nobody is trying to write data on the seemingly unused page. - * Reading an erased page will produce an ECC mismatch between - * generated and read ECC bytes that has to be dealt with separately. - * E.g. if page is 0xFF (fresh erased), and if HW ECC engine within GPMC - * is used, the result of read will be 0x0 while the ECC offsets of the - * spare area will be 0xFF which will result in an ECC mismatch. - * @mtd: MTD structure - * @dat: unused - * @ecc_code: ecc_code buffer - */ -static int __maybe_unused omap_calculate_ecc(struct mtd_info *mtd, - const uint8_t *dat, uint8_t *ecc_code) -{ - u_int32_t val; - - /* Start Reading from HW ECC1_Result = 0x200 */ - val = readl(&gpmc_cfg->ecc1_result); - - ecc_code[0] = val & 0xFF; - ecc_code[1] = (val >> 16) & 0xFF; - ecc_code[2] = ((val >> 8) & 0x0F) | ((val >> 20) & 0xF0); - - /* - * Stop reading anymore ECC vals and clear old results - * enable will be called if more reads are required - */ - writel(0x000, &gpmc_cfg->ecc_config); - - return 0; -} - -/* - * omap_enable_ecc - This function enables the hardware ecc functionality - * @mtd: MTD device structure - * @mode: Read/Write mode - */ -static void __maybe_unused omap_enable_hwecc(struct mtd_info *mtd, int32_t mode) -{ - struct nand_chip *chip = mtd->priv; - uint32_t val, dev_width = (chip->options & NAND_BUSWIDTH_16) >> 1; - - switch (mode) { - case NAND_ECC_READ: - case NAND_ECC_WRITE: - /* Clear the ecc result registers, select ecc reg as 1 */ - writel(ECCCLEAR | ECCRESULTREG1, &gpmc_cfg->ecc_control); - - /* - * Size 0 = 0xFF, Size1 is 0xFF - both are 512 bytes - * tell all regs to generate size0 sized regs - * we just have a single ECC engine for all CS - */ - writel(ECCSIZE1 | ECCSIZE0 | ECCSIZE0SEL, - &gpmc_cfg->ecc_size_config); - val = (dev_width << 7) | (cs << 1) | (0x1); - writel(val, &gpmc_cfg->ecc_config); - break; - default: - printf("Error: Unrecognized Mode[%d]!\n", mode); - break; - } -} - -/* * Generic BCH interface */ struct nand_bch_priv { @@ -239,12 +163,7 @@ struct nand_bch_priv { #define ECC_BCH8 1 #define ECC_BCH16 2 -/* GPMC ecc engine settings */ -#define BCH_WRAPMODE_1 1 /* BCH wrap mode 1 */ -#define BCH_WRAPMODE_6 6 /* BCH wrap mode 6 */ - /* BCH nibbles for diff bch levels */ -#define NAND_ECC_HW_BCH ((uint8_t)(NAND_ECC_HW_OOB_FIRST) + 1) #define ECC_BCH4_NIBBLES 13 #define ECC_BCH8_NIBBLES 26 #define ECC_BCH16_NIBBLES 52 @@ -256,266 +175,161 @@ struct nand_bch_priv { * When some users with other BCH strength will exists this have to change! */ static __maybe_unused struct nand_bch_priv bch_priv = { - .mode = NAND_ECC_HW_BCH, .type = ECC_BCH8, .nibbles = ECC_BCH8_NIBBLES, .control = NULL }; /* - * omap_hwecc_init_bch - Initialize the BCH Hardware ECC for NAND flash in - * GPMC controller - * @mtd: MTD device structure - * @mode: Read/Write mode - */ -__maybe_unused -static void omap_hwecc_init_bch(struct nand_chip *chip, int32_t mode) + * omap_reverse_list - re-orders list elements in reverse order [internal] + * @list: pointer to start of list + * @length: length of list +*/ +void omap_reverse_list(u8 *list, unsigned int length) { - uint32_t val; - uint32_t dev_width = (chip->options & NAND_BUSWIDTH_16) >> 1; - uint32_t unused_length = 0; - uint32_t wr_mode = BCH_WRAPMODE_6; - struct nand_bch_priv *bch = chip->priv; - - /* Clear the ecc result registers, select ecc reg as 1 */ - writel(ECCCLEAR | ECCRESULTREG1, &gpmc_cfg->ecc_control); - - if (bch->ecc_scheme == OMAP_ECC_BCH8_CODE_HW) { - wr_mode = BCH_WRAPMODE_1; - - switch (bch->nibbles) { - case ECC_BCH4_NIBBLES: - unused_length = 3; - break; - case ECC_BCH8_NIBBLES: - unused_length = 2; - break; - case ECC_BCH16_NIBBLES: - unused_length = 0; - break; - } - - /* - * This is ecc_size_config for ELM mode. Here we are using - * different settings for read and write access and also - * depending on BCH strength. - */ - switch (mode) { - case NAND_ECC_WRITE: - /* write access only setup eccsize1 config */ - val = ((unused_length + bch->nibbles) << 22); - break; - - case NAND_ECC_READ: - default: - /* - * by default eccsize0 selected for ecc1resultsize - * eccsize0 config. - */ - val = (bch->nibbles << 12); - /* eccsize1 config */ - val |= (unused_length << 22); - break; - } - } else { - /* - * This ecc_size_config setting is for BCH sw library. - * - * Note: we only support BCH8 currently with BCH sw library! - * Should be really easy to adobt to BCH4, however some omap3 - * have flaws with BCH4. - * - * Here we are using wrapping mode 6 both for reading and - * writing, with: - * size0 = 0 (no additional protected byte in spare area) - * size1 = 32 (skip 32 nibbles = 16 bytes per sector in - * spare area) - */ - val = (32 << 22) | (0 << 12); + unsigned int i, j; + unsigned int half_length = length / 2; + u8 tmp; + for (i = 0, j = length - 1; i < half_length; i++, j--) { + tmp = list[i]; + list[i] = list[j]; + list[j] = tmp; } - /* ecc size configuration */ - writel(val, &gpmc_cfg->ecc_size_config); - - /* - * Configure the ecc engine in gpmc - * We assume 512 Byte sector pages for access to NAND. - */ - val = (1 << 16); /* enable BCH mode */ - val |= (bch->type << 12); /* setup BCH type */ - val |= (wr_mode << 8); /* setup wrapping mode */ - val |= (dev_width << 7); /* setup device width (16 or 8 bit) */ - val |= (cs << 1); /* setup chip select to work on */ - debug("set ECC_CONFIG=0x%08x\n", val); - writel(val, &gpmc_cfg->ecc_config); } /* - * omap_enable_ecc_bch - This function enables the bch h/w ecc functionality + * omap_enable_hwecc - configures GPMC as per ECC scheme before read/write * @mtd: MTD device structure * @mode: Read/Write mode */ __maybe_unused -static void omap_enable_ecc_bch(struct mtd_info *mtd, int32_t mode) -{ - struct nand_chip *chip = mtd->priv; - - omap_hwecc_init_bch(chip, mode); - /* enable ecc */ - writel((readl(&gpmc_cfg->ecc_config) | 0x1), &gpmc_cfg->ecc_config); -} - -/* - * omap_ecc_disable - Disable H/W ECC calculation - * - * @mtd: MTD device structure - */ -static void __maybe_unused omap_ecc_disable(struct mtd_info *mtd) +static void omap_enable_hwecc(struct mtd_info *mtd, int32_t mode) { - writel((readl(&gpmc_cfg->ecc_config) & ~0x1), &gpmc_cfg->ecc_config); + struct nand_chip *nand = mtd->priv; + struct nand_bch_priv *bch = nand->priv; + unsigned int dev_width = (nand->options & NAND_BUSWIDTH_16) ? 1 : 0; + unsigned int ecc_algo = 0; + unsigned int bch_type = 0; + unsigned int eccsize1 = 0x00, eccsize0 = 0x00, bch_wrapmode = 0x00; + u32 ecc_size_config_val = 0; + u32 ecc_config_val = 0; + + /* configure GPMC for specific ecc-scheme */ + switch (bch->ecc_scheme) { + case OMAP_ECC_HAM1_CODE_SW: + return; + case OMAP_ECC_HAM1_CODE_HW: + ecc_algo = 0x0; + bch_type = 0x0; + bch_wrapmode = 0x00; + eccsize0 = 0xFF; + eccsize1 = 0xFF; + break; + case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW: + case OMAP_ECC_BCH8_CODE_HW: + ecc_algo = 0x1; + bch_type = 0x1; + if (mode == NAND_ECC_WRITE) { + bch_wrapmode = 0x01; + eccsize0 = 0; /* extra bits in nibbles per sector */ + eccsize1 = 28; /* OOB bits in nibbles per sector */ + } else { + bch_wrapmode = 0x01; + eccsize0 = 26; /* ECC bits in nibbles per sector */ + eccsize1 = 2; /* non-ECC bits in nibbles per sector */ + } + break; + default: + return; + } + /* Clear ecc and enable bits */ + writel(ECCCLEAR | ECCRESULTREG1, &gpmc_cfg->ecc_control); + /* Configure ecc size for BCH */ + ecc_size_config_val = (eccsize1 << 22) | (eccsize0 << 12); + writel(ecc_size_config_val, &gpmc_cfg->ecc_size_config); + + /* Configure device details for BCH engine */ + ecc_config_val = ((ecc_algo << 16) | /* HAM1 | BCHx */ + (bch_type << 12) | /* BCH4/BCH8/BCH16 */ + (bch_wrapmode << 8) | /* wrap mode */ + (dev_width << 7) | /* bus width */ + (0x0 << 4) | /* number of sectors */ + (cs << 1) | /* ECC CS */ + (0x1)); /* enable ECC */ + writel(ecc_config_val, &gpmc_cfg->ecc_config); } /* - * BCH support using ELM module - */ -#ifdef CONFIG_NAND_OMAP_ELM -/* - * omap_read_bch8_result - Read BCH result for BCH8 level - * - * @mtd: MTD device structure - * @big_endian: When set read register 3 first - * @ecc_code: Read syndrome from BCH result registers + * omap_calculate_ecc - Read ECC result + * @mtd: MTD structure + * @dat: unused + * @ecc_code: ecc_code buffer + * Using noninverted ECC can be considered ugly since writing a blank + * page ie. padding will clear the ECC bytes. This is no problem as + * long nobody is trying to write data on the seemingly unused page. + * Reading an erased page will produce an ECC mismatch between + * generated and read ECC bytes that has to be dealt with separately. + * E.g. if page is 0xFF (fresh erased), and if HW ECC engine within GPMC + * is used, the result of read will be 0x0 while the ECC offsets of the + * spare area will be 0xFF which will result in an ECC mismatch. */ -static void omap_read_bch8_result(struct mtd_info *mtd, uint8_t big_endian, +static int omap_calculate_ecc(struct mtd_info *mtd, const uint8_t *dat, uint8_t *ecc_code) { - uint32_t *ptr; + struct nand_chip *chip = mtd->priv; + struct nand_bch_priv *bch = chip->priv; + uint32_t *ptr, val = 0; int8_t i = 0, j; - if (big_endian) { + switch (bch->ecc_scheme) { + case OMAP_ECC_HAM1_CODE_HW: + val = readl(&gpmc_cfg->ecc1_result); + ecc_code[0] = val & 0xFF; + ecc_code[1] = (val >> 16) & 0xFF; + ecc_code[2] = ((val >> 8) & 0x0F) | ((val >> 20) & 0xF0); + break; +#ifdef CONFIG_BCH + case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW: +#endif + case OMAP_ECC_BCH8_CODE_HW: ptr = &gpmc_cfg->bch_result_0_3[0].bch_result_x[3]; - ecc_code[i++] = readl(ptr) & 0xFF; + val = readl(ptr); + ecc_code[i++] = (val >> 0) & 0xFF; ptr--; for (j = 0; j < 3; j++) { - ecc_code[i++] = (readl(ptr) >> 24) & 0xFF; - ecc_code[i++] = (readl(ptr) >> 16) & 0xFF; - ecc_code[i++] = (readl(ptr) >> 8) & 0xFF; - ecc_code[i++] = readl(ptr) & 0xFF; + val = readl(ptr); + ecc_code[i++] = (val >> 24) & 0xFF; + ecc_code[i++] = (val >> 16) & 0xFF; + ecc_code[i++] = (val >> 8) & 0xFF; + ecc_code[i++] = (val >> 0) & 0xFF; ptr--; } - } else { - ptr = &gpmc_cfg->bch_result_0_3[0].bch_result_x[0]; - for (j = 0; j < 3; j++) { - ecc_code[i++] = readl(ptr) & 0xFF; - ecc_code[i++] = (readl(ptr) >> 8) & 0xFF; - ecc_code[i++] = (readl(ptr) >> 16) & 0xFF; - ecc_code[i++] = (readl(ptr) >> 24) & 0xFF; - ptr++; - } - ecc_code[i++] = readl(ptr) & 0xFF; - ecc_code[i++] = 0; /* 14th byte is always zero */ + break; + default: + return -EINVAL; } -} - -/* - * omap_rotate_ecc_bch - Rotate the syndrome bytes - * - * @mtd: MTD device structure - * @calc_ecc: ECC read from ECC registers - * @syndrome: Rotated syndrome will be retuned in this array - * - */ -static void omap_rotate_ecc_bch(struct mtd_info *mtd, uint8_t *calc_ecc, - uint8_t *syndrome) -{ - struct nand_chip *chip = mtd->priv; - struct nand_bch_priv *bch = chip->priv; - uint8_t n_bytes = 0; - int8_t i, j; - - switch (bch->type) { - case ECC_BCH4: - n_bytes = 8; + /* ECC scheme specific syndrome customizations */ + switch (bch->ecc_scheme) { + case OMAP_ECC_HAM1_CODE_HW: break; +#ifdef CONFIG_BCH + case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW: - case ECC_BCH16: - n_bytes = 28; + for (i = 0; i < chip->ecc.bytes; i++) + *(ecc_code + i) = *(ecc_code + i) ^ + bch8_polynomial[i]; break; - - case ECC_BCH8: - default: - n_bytes = 13; +#endif + case OMAP_ECC_BCH8_CODE_HW: + ecc_code[chip->ecc.bytes - 1] = 0x00; break; + default: + return -EINVAL; } - - for (i = 0, j = (n_bytes-1); i < n_bytes; i++, j--) - syndrome[i] = calc_ecc[j]; -} - -/* - * omap_calculate_ecc_bch - Read BCH ECC result - * - * @mtd: MTD structure - * @dat: unused - * @ecc_code: ecc_code buffer - */ -static int omap_calculate_ecc_bch(struct mtd_info *mtd, const uint8_t *dat, - uint8_t *ecc_code) -{ - struct nand_chip *chip = mtd->priv; - struct nand_bch_priv *bch = chip->priv; - uint8_t big_endian = 1; - int8_t ret = 0; - - if (bch->type == ECC_BCH8) - omap_read_bch8_result(mtd, big_endian, ecc_code); - else /* BCH4 and BCH16 currently not supported */ - ret = -1; - - /* - * Stop reading anymore ECC vals and clear old results - * enable will be called if more reads are required - */ - omap_ecc_disable(mtd); - - return ret; -} - -/* - * omap_fix_errors_bch - Correct bch error in the data - * - * @mtd: MTD device structure - * @data: Data read from flash - * @error_count:Number of errors in data - * @error_loc: Locations of errors in the data - * - */ -static void omap_fix_errors_bch(struct mtd_info *mtd, uint8_t *data, - uint32_t error_count, uint32_t *error_loc) -{ - struct nand_chip *chip = mtd->priv; - struct nand_bch_priv *bch = chip->priv; - uint8_t count = 0; - uint32_t error_byte_pos; - uint32_t error_bit_mask; - uint32_t last_bit = (bch->nibbles * 4) - 1; - - /* Flip all bits as specified by the error location array. */ - /* FOR( each found error location flip the bit ) */ - for (count = 0; count < error_count; count++) { - if (error_loc[count] > last_bit) { - /* Remove the ECC spare bits from correction. */ - error_loc[count] -= (last_bit + 1); - /* Offset bit in data region */ - error_byte_pos = ((512 * 8) - - (error_loc[count]) - 1) / 8; - /* Error Bit mask */ - error_bit_mask = 0x1 << (error_loc[count] % 8); - /* Toggle the error bit to make the correction. */ - data[error_byte_pos] ^= error_bit_mask; - } - } + return 0; } +#ifdef CONFIG_NAND_OMAP_ELM /* * omap_correct_data_bch - Compares the ecc read from nand spare area * with ECC registers values and corrects one bit error if it has occured @@ -532,40 +346,72 @@ static int omap_correct_data_bch(struct mtd_info *mtd, uint8_t *dat, { struct nand_chip *chip = mtd->priv; struct nand_bch_priv *bch = chip->priv; - uint8_t syndrome[28]; - uint32_t error_count = 0; + uint32_t eccbytes = chip->ecc.bytes; + uint32_t error_count = 0, error_max; uint32_t error_loc[8]; - uint32_t i, ecc_flag; + uint32_t i, ecc_flag = 0; + uint8_t count, err = 0; + uint32_t byte_pos, bit_pos; + + /* check calculated ecc */ + for (i = 0; i < chip->ecc.bytes && !ecc_flag; i++) { + if (calc_ecc[i] != 0x00) + ecc_flag = 1; + } + if (!ecc_flag) + return 0; + /* check for whether its a erased-page */ ecc_flag = 0; - for (i = 0; i < chip->ecc.bytes; i++) + for (i = 0; i < chip->ecc.bytes && !ecc_flag; i++) { if (read_ecc[i] != 0xff) ecc_flag = 1; - + } if (!ecc_flag) return 0; - elm_reset(); - elm_config((enum bch_level)(bch->type)); - /* * while reading ECC result we read it in big endian. * Hence while loading to ELM we have rotate to get the right endian. */ - omap_rotate_ecc_bch(mtd, calc_ecc, syndrome); - + switch (bch->ecc_scheme) { + case OMAP_ECC_BCH8_CODE_HW: + omap_reverse_list(calc_ecc, eccbytes - 1); + break; + default: + return -EINVAL; + } /* use elm module to check for errors */ - if (elm_check_error(syndrome, bch->nibbles, &error_count, - error_loc) != 0) { - printf("ECC: uncorrectable.\n"); - return -1; + elm_config((enum bch_level)(bch->type)); + if (elm_check_error(calc_ecc, bch->nibbles, &error_count, error_loc)) { + printf("nand: error: uncorrectable ECC errors\n"); + return -EINVAL; } - /* correct bch error */ - if (error_count > 0) - omap_fix_errors_bch(mtd, dat, error_count, error_loc); - - return 0; + for (count = 0; count < error_count; count++) { + switch (bch->type) { + case ECC_BCH8: + /* 14th byte in ECC is reserved to match ROM layout */ + error_max = SECTOR_BYTES + (eccbytes - 1); + break; + default: + return -EINVAL; + } + byte_pos = error_max - (error_loc[count] / 8) - 1; + bit_pos = error_loc[count] % 8; + if (byte_pos < SECTOR_BYTES) { + dat[byte_pos] ^= 1 << bit_pos; + printf("nand: bit-flip corrected @data=%d\n", byte_pos); + } else if (byte_pos < error_max) { + read_ecc[byte_pos - SECTOR_BYTES] = 1 << bit_pos; + printf("nand: bit-flip corrected @oob=%d\n", byte_pos - + SECTOR_BYTES); + } else { + err = -EBADMSG; + printf("nand: error: invalid bit-flip location\n"); + } + } + return (err) ? err : error_count; } /** @@ -636,57 +482,6 @@ static int omap_read_page_bch(struct mtd_info *mtd, struct nand_chip *chip, * OMAP3 BCH8 support (with BCH library) */ #ifdef CONFIG_BCH -/* - * omap_calculate_ecc_bch_sw - Read BCH ECC result - * - * @mtd: MTD device structure - * @dat: The pointer to data on which ecc is computed (unused here) - * @ecc: The ECC output buffer - */ -static int omap_calculate_ecc_bch_sw(struct mtd_info *mtd, const uint8_t *dat, - uint8_t *ecc) -{ - int ret = 0; - size_t i; - unsigned long nsectors, val1, val2, val3, val4; - - nsectors = ((readl(&gpmc_cfg->ecc_config) >> 4) & 0x7) + 1; - - for (i = 0; i < nsectors; i++) { - /* Read hw-computed remainder */ - val1 = readl(&gpmc_cfg->bch_result_0_3[i].bch_result_x[0]); - val2 = readl(&gpmc_cfg->bch_result_0_3[i].bch_result_x[1]); - val3 = readl(&gpmc_cfg->bch_result_0_3[i].bch_result_x[2]); - val4 = readl(&gpmc_cfg->bch_result_0_3[i].bch_result_x[3]); - - /* - * Add constant polynomial to remainder, in order to get an ecc - * sequence of 0xFFs for a buffer filled with 0xFFs. - */ - *ecc++ = 0xef ^ (val4 & 0xFF); - *ecc++ = 0x51 ^ ((val3 >> 24) & 0xFF); - *ecc++ = 0x2e ^ ((val3 >> 16) & 0xFF); - *ecc++ = 0x09 ^ ((val3 >> 8) & 0xFF); - *ecc++ = 0xed ^ (val3 & 0xFF); - *ecc++ = 0x93 ^ ((val2 >> 24) & 0xFF); - *ecc++ = 0x9a ^ ((val2 >> 16) & 0xFF); - *ecc++ = 0xc2 ^ ((val2 >> 8) & 0xFF); - *ecc++ = 0x97 ^ (val2 & 0xFF); - *ecc++ = 0x79 ^ ((val1 >> 24) & 0xFF); - *ecc++ = 0xe5 ^ ((val1 >> 16) & 0xFF); - *ecc++ = 0x24 ^ ((val1 >> 8) & 0xFF); - *ecc++ = 0xb5 ^ (val1 & 0xFF); - } - - /* - * Stop reading anymore ECC vals and clear old results - * enable will be called if more reads are required - */ - omap_ecc_disable(mtd); - - return ret; -} - /** * omap_correct_data_bch_sw - Decode received data and correct errors * @mtd: MTD device structure @@ -835,9 +630,9 @@ static int omap_select_ecc_scheme(struct nand_chip *nand, nand->ecc.strength = 8; nand->ecc.size = SECTOR_BYTES; nand->ecc.bytes = 13; - nand->ecc.hwctl = omap_enable_ecc_bch; + nand->ecc.hwctl = omap_enable_hwecc; nand->ecc.correct = omap_correct_data_bch_sw; - nand->ecc.calculate = omap_calculate_ecc_bch_sw; + nand->ecc.calculate = omap_calculate_ecc; /* define ecc-layout */ ecclayout->eccbytes = nand->ecc.bytes * eccsteps; ecclayout->eccpos[0] = BADBLOCK_MARKER_LENGTH; @@ -852,7 +647,6 @@ static int omap_select_ecc_scheme(struct nand_chip *nand, ecclayout->oobfree[0].offset = i + BADBLOCK_MARKER_LENGTH; ecclayout->oobfree[0].length = oobsize - ecclayout->eccbytes - BADBLOCK_MARKER_LENGTH; - omap_hwecc_init_bch(nand, NAND_ECC_READ); bch->ecc_scheme = OMAP_ECC_BCH8_CODE_HW_DETECTION_SW; break; #else @@ -878,9 +672,9 @@ static int omap_select_ecc_scheme(struct nand_chip *nand, nand->ecc.strength = 8; nand->ecc.size = SECTOR_BYTES; nand->ecc.bytes = 14; - nand->ecc.hwctl = omap_enable_ecc_bch; + nand->ecc.hwctl = omap_enable_hwecc; nand->ecc.correct = omap_correct_data_bch; - nand->ecc.calculate = omap_calculate_ecc_bch; + nand->ecc.calculate = omap_calculate_ecc; nand->ecc.read_page = omap_read_page_bch; /* define ecc-layout */ ecclayout->eccbytes = nand->ecc.bytes * eccsteps; diff --git a/drivers/mtd/spi/sf_ops.c b/drivers/mtd/spi/sf_ops.c index 1f1bb36..ef91b92 100644 --- a/drivers/mtd/spi/sf_ops.c +++ b/drivers/mtd/spi/sf_ops.c @@ -9,6 +9,7 @@ */ #include <common.h> +#include <errno.h> #include <malloc.h> #include <spi.h> #include <spi_flash.h> @@ -381,8 +382,11 @@ int spi_flash_cmd_read_ops(struct spi_flash *flash, u32 offset, } cmdsz = SPI_FLASH_CMD_LEN + flash->dummy_byte; - cmd = malloc(cmdsz); - memset(cmd, 0, cmdsz); + cmd = calloc(1, cmdsz); + if (!cmd) { + debug("SF: Failed to allocate cmd\n"); + return -ENOMEM; + } cmd[0] = flash->read_cmd; while (len) { diff --git a/drivers/mtd/spi/sf_params.c b/drivers/mtd/spi/sf_params.c index daf8fe7..eb372b7 100644 --- a/drivers/mtd/spi/sf_params.c +++ b/drivers/mtd/spi/sf_params.c @@ -54,10 +54,11 @@ const struct spi_flash_params spi_flash_params_table[] = { {"S25FL128P_64K", 0x012018, 0x0301, 64 * 1024, 256, RD_FULL, WR_QPP}, {"S25FL032P", 0x010215, 0x4d00, 64 * 1024, 64, RD_FULL, WR_QPP}, {"S25FL064P", 0x010216, 0x4d00, 64 * 1024, 128, RD_FULL, WR_QPP}, + {"S25FL128S_256K", 0x012018, 0x4d00, 256 * 1024, 64, RD_FULL, WR_QPP}, {"S25FL128S_64K", 0x012018, 0x4d01, 64 * 1024, 256, RD_FULL, WR_QPP}, - {"S25FL256S_256K", 0x010219, 0x4d00, 64 * 1024, 512, RD_FULL, WR_QPP}, + {"S25FL256S_256K", 0x010219, 0x4d00, 256 * 1024, 128, RD_FULL, WR_QPP}, {"S25FL256S_64K", 0x010219, 0x4d01, 64 * 1024, 512, RD_FULL, WR_QPP}, - {"S25FL512S_256K", 0x010220, 0x4d00, 64 * 1024, 1024, RD_FULL, WR_QPP}, + {"S25FL512S_256K", 0x010220, 0x4d00, 256 * 1024, 256, RD_FULL, WR_QPP}, {"S25FL512S_64K", 0x010220, 0x4d01, 64 * 1024, 1024, RD_FULL, WR_QPP}, #endif #ifdef CONFIG_SPI_FLASH_STMICRO /* STMICRO */ diff --git a/drivers/mtd/spi/sf_probe.c b/drivers/mtd/spi/sf_probe.c index bc3cf6c..0a46fe3 100644 --- a/drivers/mtd/spi/sf_probe.c +++ b/drivers/mtd/spi/sf_probe.c @@ -123,12 +123,11 @@ static struct spi_flash *spi_flash_validate_params(struct spi_slave *spi, return NULL; } - flash = malloc(sizeof(*flash)); + flash = calloc(1, sizeof(*flash)); if (!flash) { debug("SF: Failed to allocate spi_flash\n"); return NULL; } - memset(flash, '\0', sizeof(*flash)); /* Assign spi data */ flash->spi = spi; @@ -147,7 +146,21 @@ static struct spi_flash *spi_flash_validate_params(struct spi_slave *spi, /* Compute the flash size */ flash->shift = (flash->dual_flash & SF_DUAL_PARALLEL_FLASH) ? 1 : 0; - flash->page_size = ((ext_jedec == 0x4d00) ? 512 : 256) << flash->shift; + /* + * The Spansion S25FL032P and S25FL064P have 256b pages, yet use the + * 0x4d00 Extended JEDEC code. The rest of the Spansion flashes with + * the 0x4d00 Extended JEDEC code have 512b pages. All of the others + * have 256b pages. + */ + if (ext_jedec == 0x4d00) { + if ((jedec == 0x0215) || (jedec == 0x216)) + flash->page_size = 256; + else + flash->page_size = 512; + } else { + flash->page_size = 256; + } + flash->page_size <<= flash->shift; flash->sector_size = params->sector_size << flash->shift; flash->size = flash->sector_size * params->nr_sectors << flash->shift; #ifdef CONFIG_SF_DUAL_FLASH |