diff options
Diffstat (limited to 'drivers/mtd/nand/nand_base.c')
| -rw-r--r-- | drivers/mtd/nand/nand_base.c | 21 |
1 files changed, 19 insertions, 2 deletions
diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c index ef37f97..d33fee2 100644 --- a/drivers/mtd/nand/nand_base.c +++ b/drivers/mtd/nand/nand_base.c @@ -75,6 +75,17 @@ #include <jffs2/jffs2.h> #endif +/* + * CONFIG_SYS_NAND_RESET_CNT is used as a timeout mechanism when resetting + * a flash. NAND flash is initialized prior to interrupts so standard timers + * can't be used. CONFIG_SYS_NAND_RESET_CNT should be set to a value + * which is greater than (max NAND reset time / NAND status read time). + * A conservative default of 200000 (500 us / 25 ns) is used as a default. + */ +#ifndef CONFIG_SYS_NAND_RESET_CNT +#define CONFIG_SYS_NAND_RESET_CNT 200000 +#endif + /* Define default oob placement schemes for large and small page devices */ static struct nand_ecclayout nand_oob_8 = { .eccbytes = 3, @@ -524,6 +535,7 @@ static void nand_command(struct mtd_info *mtd, unsigned int command, { register struct nand_chip *chip = mtd->priv; int ctrl = NAND_CTRL_CLE | NAND_CTRL_CHANGE; + uint32_t rst_sts_cnt = CONFIG_SYS_NAND_RESET_CNT; /* * Write out the command to the device. @@ -590,7 +602,8 @@ static void nand_command(struct mtd_info *mtd, unsigned int command, NAND_CTRL_CLE | NAND_CTRL_CHANGE); chip->cmd_ctrl(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE); - while (!(chip->read_byte(mtd) & NAND_STATUS_READY)) ; + while (!(chip->read_byte(mtd) & NAND_STATUS_READY) && + (rst_sts_cnt--)); return; /* This applies to read commands */ @@ -626,6 +639,7 @@ static void nand_command_lp(struct mtd_info *mtd, unsigned int command, int column, int page_addr) { register struct nand_chip *chip = mtd->priv; + uint32_t rst_sts_cnt = CONFIG_SYS_NAND_RESET_CNT; /* Emulate NAND_CMD_READOOB */ if (command == NAND_CMD_READOOB) { @@ -696,7 +710,8 @@ static void nand_command_lp(struct mtd_info *mtd, unsigned int command, NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE); chip->cmd_ctrl(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE); - while (!(chip->read_byte(mtd) & NAND_STATUS_READY)) ; + while (!(chip->read_byte(mtd) & NAND_STATUS_READY) && + (rst_sts_cnt--)); return; case NAND_CMD_RNDOUT: @@ -2618,7 +2633,9 @@ int nand_scan_ident(struct mtd_info *mtd, int maxchips) type = nand_get_flash_type(mtd, chip, busw, &nand_maf_id); if (IS_ERR(type)) { +#ifndef CONFIG_SYS_NAND_QUIET_TEST printk(KERN_WARNING "No NAND device found!!!\n"); +#endif chip->select_chip(mtd, -1); return PTR_ERR(type); } |