summaryrefslogtreecommitdiff
path: root/doc
diff options
context:
space:
mode:
Diffstat (limited to 'doc')
-rw-r--r--doc/README.sbc834930
1 files changed, 20 insertions, 10 deletions
diff --git a/doc/README.sbc8349 b/doc/README.sbc8349
index a0ac638..908e768 100644
--- a/doc/README.sbc8349
+++ b/doc/README.sbc8349
@@ -21,15 +21,22 @@ Flash Details:
The flash type is intel 28F640Jx (4096x16) [one device]. Base address
is 0xFF80_0000 which is also where the Hardware Reset Configuration
-Word (HRCW) is stored. Caution should be used to not overwrite the
-HRCW, or "CF RCW" with a Wind River ICE will be required to restore
-the HRCW and allow the board to enter background mode for further
-steps in the flash process.
+Word (HRCW) is stored. Caution should be used to not reset the
+board without having a valid HRCW in place (i.e. erased flash) as
+then a Wind River ICE will be required to restore the HRCW and flash
+image.
Restoring a corrupted or missing flash image:
=============================================
+Note that U-boot versions up to and including 2009.06 had essentially
+two copies of u-boot in flash; one at the very beginning, which set
+the HRCW, and one at the very end, which was the image that was run.
+As of this point in time, the two have been combined into just one
+at the beginning of flash, which provides both the HRCW, and the image
+that is executed. This frees up the remainder of flash for other uses.
+Use of the u-boot command "fli" will indicate what parts are in use.
Details for storing U-boot to flash using a Wind River ICE can be found
on page 19 of the board manual (request ERG-00328-001). The following
is a summary of that information:
@@ -39,9 +46,9 @@ is a summary of that information:
- Select the appropriate flash type (listed above)
- Prepare a u-boot image by using the Wind River Convert utility;
by using "Convert and Add file" on the ELF file from your build.
- Convert from FFF0_0000 to FFFF_FFFF (or to FFF3_FFFF if you are
- trying to preserve your old environment settings).
- - Set the start address of the erase/flash process to FFF0_0000
+ Convert from FF80_0000 to FFFF_FFFF (or to FF83_FFFF if you are
+ trying to preserve your old environment settings and user flash).
+ - Set the start address of the erase/flash process to FF80_0000
- Set the target RAM required to 64kB.
- Select sectors for erasing (see note on enviroment below)
- Select Erase and Reprogram.
@@ -59,7 +66,7 @@ beginning with "SCGA TSEC1" and "SCGA TSEC2". This allows you to
use all the remaining register file content.
If you wish to preserve your prior U-Boot environment settings,
-then convert (and erase to) 0xFFF3FFFF instead of 0xFFFFFFFF.
+then convert (and erase to) 0xFF83FFFF instead of 0xFFFFFFFF.
The size for converting (and erasing) must be at least as large
as u-boot.bin.
@@ -73,10 +80,13 @@ has been copied to the TFTP server, the commands are:
tftp 200000 u-boot.bin
protect off all
- erase fff00000 fff3ffff
- cp.b 200000 fff00000 3ffff
+ erase ff800000 ff83ffff
+ cp.b 200000 ff800000 40000
protect on all
+You may wish to do a "md ff800000 20" operation as a prefix and postfix
+to the above steps to inspect/compare the HRCW before/after as an extra
+safety check before resetting the board upon completion of the reflash.
PCI:
====