diff options
Diffstat (limited to 'doc')
| -rw-r--r-- | doc/README.INCA-IP | 1 | ||||
| -rw-r--r-- | doc/README.mpc85xxads | 535 | ||||
| -rw-r--r-- | doc/README.nios | 2 |
3 files changed, 535 insertions, 3 deletions
diff --git a/doc/README.INCA-IP b/doc/README.INCA-IP index 7421b6e..1329152 100644 --- a/doc/README.INCA-IP +++ b/doc/README.INCA-IP @@ -41,7 +41,6 @@ to install a U-Boot image into flash. go 0xb0000000 - Ethernet autonegotiation needs some time to complete. Instead of delaying the boot process in all cases, we just start the autonegotiation process when U-Boot comes up and that is all. Most diff --git a/doc/README.mpc85xxads b/doc/README.mpc85xxads new file mode 100644 index 0000000..3eb5d95 --- /dev/null +++ b/doc/README.mpc85xxads @@ -0,0 +1,535 @@ +Motorola MPC8540ADS and MPC8560ADS board + +Xianghua Xiao(X.Xiao@motorola.com) +Created 10/15/03 +----------------------------------------- + +1. SWITCH SETTINGS & JUMPERS +1.1 First, make sure the board default setting is consistent with the document + shipped with your board. Then apply the following changes: + SW3[1-6]="all OFF" (boot from 32bit flash, no boot sequence is used) + SW10[2-6]="all OFF" (turn on CPM SCC for serial port,works for 8540/8560) + SW11[2]='OFF for dracom, ON for draco' (single switch to toggle draco.dracom mode) + SW4[7-8]="OFF OFF" (enable serial ports,I'm using the top serial connector) + SW22[1-4]="OFF OFF ON OFF" + SW5[1-10[="ON ON OFF OFF OFF OFF OFF OFF OFF OFF" + J1 = "Enable Prog" (Make sure your flash is programmable for development) + Ethernet PHY connectors(J47,J56) should be removed if you want to use the ethernet. +1.2 If you want to test PCI functionality with a 33Mhz PCI card, you will have to change + the system clock from the default 66Mhz to 33Mhz by setting SW15[1]="OFF" and + SW17[8]="OFF". After that you may also need double your platform clock(SW6) because + the system clock is now only half of its original value. +1.3 SW6 is a very important switch, it decides your platform clock and CPU clock based on + the on-board system clock(default 66MHz). Check the document along with your board + for details. + +2. MEMORY MAP TO WORK WITH LINUX KERNEL +2.1. For the initial bringup, we adopted a consistent memory scheme between u-boot and + linux kernel, you can customize it based on your system requirements: + DDR: 0x00000000-0x1fffffff (max 512MB) + PCI: 0xe0000000-0xefffffff (256MB) + RIO: 0xf0000000-0xf7ffffff (128MB) + Local SDRAM: 0xf8000000-0xfbffffff (64MB) + Local CSx: 0xfc000000-0xfdefffff (31MB) BCSR,RTC,ATM config,etc. + CCSRBAR: 0xfdf00000-0xfdffffff (1MB) + Flash: 0xfe000000-0xffffffff (max 32MB) +2.2 We are submitting Linux kernel patches for MPC8540 and MPC8560. Hope you will be + able to download them from linuxppc-2.4 public source by the time you are reading + this. Please make sure the kernel's ppcboot.h is consistent with U-Boot's u-boot.h, + then you can use two default configuration files in the kernel source as a test: + arch/ppc/configs/mpc8540ads_defconfig + arch/ppc/configs/mpc8560ads_defconfig + +3. DEFINITIONS AND COMPILATION +3.1 Explanation on NEW definitions in include/configs/MPC8540ADS.h and include/ + configs/MPC8560ADS.h + CONFIG_BOOKE BOOKE(e.g. Motorola MPC85xx, IBM 440, etc) + CONFIG_E500 BOOKE e500 family(Motorola) + CONFIG_MPC85xx MPC8540,MPC8560 and their derivatives + CONFIG_MPC85xx_REV1 MPC85xx Rev 1 Chip, in general you will use a Rev2 + chip from Nov.2003. If you still see this definition + while you have a Rev2(and newer) chip,undef this. + CONFIG_MPC8540 MPC8540 specific + CONFIG_MPC8560 MPC8560 specific + CONFIG_MPC8540ADS MPC8540ADS board specific + CONFIG_MPC8560ADS MPC8560ADS board specific + CONFIG_TSEC_ENET Use on-chip 10/100/1000 ethernet for networking + CONFIG_SPD_EEPROM Use SPD EEPROM for DDR auto configuration, you can also + manual config the DDR after undef this definition. + CONFIG_DDR_ECC only for ECC DDR module + CONFIG_DDR_DLL possible DLL fix needed for Rev1 chip for more stability. + you can disable this if you're having a newer chip. + CONFIG_RAM_AS_FLASH after define this, you can load U-Boot into localbus + SDRAM and treat localbus SDRAM as a flash. We use this + memory based U-Boot before flash is working while Metrowerks + and Windriver are still working on their flash/JTAG tools. + if you can program the flash directly, undef this. + Other than the above definitions, the rest in the config files are straightforward. + + +3.2 Compilation + export CROSS_COMPILE=your-cross-compile-prefix(assuming you're using BASH shell) + cd u-boot + make distclean + make MPC8560ADS_config (or make MPC8540ADS_config) + make + +4. Note on the 10/100/1000 Ethernet controller: +4.1 Sometimes after U-Boot is up, the 'tftp' won't work well with TSEC ethernet. If that + happens, you can try the following steps to make network work: + MPC8560ADS>tftp 1000000 pImage + (if it hangs, use Ctrl-C to quit) + MPC8560ADS>nm fdf24524 + >0 + >1 + >. (to quit this memory operation) + MPC8560ADS>tftp 1000000 pImage + +5. Screen dump: +5.1 MPC8540ADS board +U-Boot 1.0.0-pre (Oct 15 2003 - 13:40:33) + +Motorola PowerPC ProcessorID=00000000 Rev. PVR=80200010 +Board: Motorola MPC8540ADS Board + CPU: 792 MHz + CCB: 264 MHz + DDR: 132 MHz + LBC: 66 MHz +L1 D-cache 32KB, L1 I-cache 32KB enabled. +I2C: ready +DRAM: DDR module detected, total size:128MB. +128 MB +FLASH: 16 MB +L2 cache enabled: 256KB +*** Warning - bad CRC, using default environment + +In: serial +Out: serial +Err: serial +Net: MOTOROLA ETHERNE +Hit any key to stop autoboot: 0 +MPC8540ADS=> fli + +Bank # 1: Intel 28F640J3A (64 Mbit, 64 x 128K) + Size: 16 MB in 64 Sectors + Sector Start Addresses: + FF000000 FF040000 FF080000 FF0C0000 FF100000 + FF140000 FF180000 FF1C0000 FF200000 FF240000 + FF280000 FF2C0000 FF300000 FF340000 FF380000 + FF3C0000 FF400000 FF440000 FF480000 FF4C0000 + FF500000 FF540000 FF580000 FF5C0000 FF600000 + FF640000 FF680000 FF6C0000 FF700000 FF740000 + FF780000 FF7C0000 FF800000 FF840000 FF880000 + FF8C0000 FF900000 FF940000 FF980000 FF9C0000 + FFA00000 FFA40000 FFA80000 FFAC0000 FFB00000 + FFB40000 FFB80000 FFBC0000 FFC00000 FFC40000 + FFC80000 FFCC0000 FFD00000 FFD40000 FFD80000 + FFDC0000 FFE00000 FFE40000 FFE80000 FFEC0000 + FFF00000 FFF40000 FFF80000 (RO) FFFC0000 (RO) +MPC8540ADS=> imi ff000000 + +## Checking Image at ff000000 ... + Image Name: Linux-2.4.21-rc5 + Image Type: PowerPC Linux Kernel Image (gzip compressed) + Data Size: 800594 Bytes = 781.8 kB + Load Address: 00000000 + Entry Point: 00000000 + Verifying Checksum ... OK +MPC8540ADS=> bdinfo +memstart = 0x00000000 +memsize = 0x08000000 +flashstart = 0xFF000000 +flashsize = 0x01000000 +flashoffset = 0x00000000 +sramstart = 0x00000000 +sramsize = 0x00000000 +immr_base = 0xFDF00000 +bootflags = 0x40003F80 +intfreq = 792 MHz +busfreq = 264 MHz +ethaddr = 00:01:AF:07:9B:8A +eth1addr = 00:01:AF:07:9B:8B +eth2addr = 00:01:AF:07:9B:8C +IP addr = 10.82.0.105 +baudrate = 115200 bps +MPC8540ADS=> printenv +bootargs=root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8540ads-003:eth0:off console=ttyS0,115200 +bootcmd=bootm 0xff300000 0xff700000 +bootdelay=3 +baudrate=115200 +loads_echo=1 +ethaddr=00:01:af:07:9b:8a +eth1addr=00:01:af:07:9b:8b +eth2addr=00:01:af:07:9b:8c +ipaddr=10.82.0.105 +serverip=163.12.64.52 +rootpath=/home/r6aads/mpclinux/eldk-2.0.2/ppc_82xx +gatewayip=10.82.1.254 +netmask=255.255.254.0 +hostname=MPC8560ADS_PILOT_003 +bootfile=pImage +stdin=serial +stdout=serial +stderr=serial + +Environment size: 560/8188 bytes +MPC8540ADS=> bootm ff000000 +## Booting image at ff000000 ... + Image Name: Linux-2.4.21-rc5 + Image Type: PowerPC Linux Kernel Image (gzip compressed) + Data Size: 800594 Bytes = 781.8 kB + Load Address: 00000000 + Entry Point: 00000000 + Verifying Checksum ... OK + Uncompressing Kernel Image ... OK +mpc85xx_init(): exit +id mach(): done +MMU:enter +Memory CAM mapping: CAM0=64Mb, CAM1=64Mb, CAM2=0Mb residual: 0Mb +MMU:hw init +MMU:mapin +MMU:mapin_ram done +MMU:setio +MMU:exit +Linux version 2.4.21-rc5 (@etest) (gcc version 2.95.3 20010315 (release)) #1 Wed Oct 15 09:05:42 CDT 2003 +setup_arch: enter +setup_arch: bootmem +mpc85xx_setup_arch +Host Bridge Vendor ID = 1057 +Host Bridge Device ID = 3 +Host Bridge header = 0 +arch: exit +On node 0 totalpages: 32768 +zone(0): 32768 pages. +zone(1): 0 pages. +zone(2): 0 pages. +Kernel command line: root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8540ads-003:eth0:off console=ttyS0,115200 +openpic: enter +OpenPIC Version 1.2 (1 CPUs and 44 IRQ sources) at fdf40000 +openpic: timer +openpic: external +openpic: spurious +openpic: exit +time_init: decrementer frequency = 33.000000 MHz +Calibrating delay loop... 226.09 BogoMIPS +Memory: 127488k available (1344k kernel code, 448k data, 248k init, 0k highmem) +Dentry cache hash table entries: 16384 (order: 5, 131072 bytes) +Inode cache hash table entries: 8192 (order: 4, 65536 bytes) +Mount cache hash table entries: 512 (order: 0, 4096 bytes) +Buffer-cache hash table entries: 8192 (order: 3, 32768 bytes) +Page-cache hash table entries: 32768 (order: 5, 131072 bytes) +POSIX conformance testing by UNIFIX +PCI: Probing PCI hardware + +Linux NET4.0 for Linux 2.4 +Based upon Swansea University Computer Society NET3.039 +Initializing RT netlink socket +Starting kswapd +Installing knfsd (copyright (C) 1996 okir@monad.swb.de). +pty: 256 Unix98 ptys configured +Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled +ttyS00 at 0xfdf04500 (irq = 90) is a 16550A +ttyS01 at 0xfdf04600 (irq = 0) is a 16550A +eth0: Three Speed Ethernet Controller Version 0.2, 00:01:af:07:9b:8a: +eth1: Three Speed Ethernet Controller Version 0.2, 00:01:af:07:9b:8b: +RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize +loop: loaded (max 8 devices) +Intel(R) PRO/1000 Network Driver - version 5.0.43-k1 +Copyright (c) 1999-2003 Intel Corporation. +PPP generic driver version 2.4.2 +PPP Deflate Compression module registered +NET4: Linux TCP/IP 1.0 for NET4.0 +IP Protocols: ICMP, UDP, TCP, IGMP +IP: routing cache hash table of 1024 buckets, 8Kbytes +TCP: Hash tables configured (established 8192 bind 8192) +IP-Config: Complete: + device=eth0, addr=10.82.0.105, mask=255.255.254.0, gw=10.82.1.254, + host=mpc8540ads-003, domain=, nis-domain=(none), + bootserver=163.12.64.52, rootserver=163.12.64.52, rootpath= +NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. +Looking up port of RPC 100003/2 on 163.12.64.52 +Looking up port of RPC 100005/1 on 163.12.64.52 +VFS: Mounted root (nfs filesystem). +Freeing unused kernel memory: 248k init +INIT: version 2.78 booting +Activating swap... +Checking all file systems... +Parallelizing fsck version 1.22 (22-Jun-2001) +Mounting local filesystems... +nothing was mounted +Cleaning: /etc/network/ifstate. +Setting up IP spoofing protection: rp_filter. +Disable TCP/IP Explicit Congestion Notification: done. +Configuring network interfaces: done. +Starting portmap daemon: portmap. +Cleaning: /tmp /var/lock /var/run. +INIT: Entering runlevel: 2 +Starting system log daemon: syslogd klogd. +Starting internet superserver: inetd. + +mpc8540ads-003 login: root +Last login: Thu Jan 1 00:00:07 1970 on console +Linux mpc8540ads-003 2.4.21-rc5 #1 Wed Oct 15 09:05:42 CDT 2003 ppc unknown + +root@mpc8540ads-003:~# ls +21142.o aa e100.o hello.o mii.o timer.o +root@mpc8540ads-003:~# /sbin/ifconfig +eth0 Link encap:Ethernet HWaddr 00:01:AF:07:9B:8A + inet addr:10.82.0.105 Bcast:10.82.1.255 Mask:255.255.254.0 + UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 + RX packets:4576 errors:0 dropped:0 overruns:0 frame:0 + TX packets:2587 errors:0 dropped:0 overruns:0 carrier:0 + collisions:0 txqueuelen:100 + RX bytes:4457023 (4.2 Mb) TX bytes:437770 (427.5 Kb) + Base address:0x4000 + +lo Link encap:Local Loopback + inet addr:127.0.0.1 Mask:255.0.0.0 + UP LOOPBACK RUNNING MTU:16436 Metric:1 + RX packets:4 errors:0 dropped:0 overruns:0 frame:0 + TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 + collisions:0 txqueuelen:0 + RX bytes:296 (296.0 b) TX bytes:296 (296.0 b) + +root@mpc8540ads-003:~# ping 163.12.64.52 +PING 163.12.64.52 (163.12.64.52): 56 data bytes +64 bytes from 163.12.64.52: icmp_seq=0 ttl=63 time=0.2 ms +64 bytes from 163.12.64.52: icmp_seq=1 ttl=63 time=0.1 ms +64 bytes from 163.12.64.52: icmp_seq=2 ttl=63 time=0.1 ms + +--- 163.12.64.52 ping statistics --- +3 packets transmitted, 3 packets received, 0% packet loss +round-trip min/avg/max = 0.1/0.1/0.2 ms +root@mpc8540ads-003:~# + +5.2 MPC8560ADS board +U-Boot 1.0.0-pre (Oct 15 2003 - 13:42:04) + +Motorola PowerPC ProcessorID=00000000 Rev. PVR=80200010 +Board: Motorola MPC8560ADS Board + CPU: 792 MHz + CCB: 264 MHz + DDR: 132 MHz + LBC: 66 MHz + CPM: 264 Mhz +L1 D-cache 32KB, L1 I-cache 32KB enabled. +I2C: ready +DRAM: DDR module detected, total size:128MB. +128 MB +FLASH: 16 MB +L2 cache enabled: 256KB +*** Warning - bad CRC, using default environment + +In: serial +Out: serial +Err: serial +Net: MOTOROLA ETHERNE +Hit any key to stop autoboot: 3 +MPC8560ADS=> bdinfo +memstart = 0x00000000 +memsize = 0x08000000 +flashstart = 0xFF000000 +flashsize = 0x01000000 +flashoffset = 0x00000000 +sramstart = 0x00000000 +sramsize = 0x00000000 +immr_base = 0xFDF00000 +bootflags = 0x00000000 +vco = 528 MHz +sccfreq = 132 MHz +brgfreq = 132 MHz +intfreq = 792 MHz +cpmfreq = 264 MHz +busfreq = 264 MHz +ethaddr = 00:01:AF:07:9B:8A +eth1addr = 00:01:AF:07:9B:8B +eth2addr = 00:01:AF:07:9B:8C +IP addr = 10.82.0.105 +baudrate = 115200 bps +MPC8560ADS=> printenv +bootargs=root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8560ads-003:eth0:off console=ttyS0,115200 +bootcmd=bootm 0xff400000 0xff700000 +bootdelay=3 +baudrate=115200 +loads_echo=1 +ethaddr=00:01:af:07:9b:8a +eth1addr=00:01:af:07:9b:8b +eth2addr=00:01:af:07:9b:8c +ipaddr=10.82.0.105 +serverip=163.12.64.52 +rootpath=/home/r6aads/mpclinux/eldk-2.0.2/ppc_82xx +gatewayip=10.82.1.254 +netmask=255.255.254.0 +hostname=MPC8560ADS_PILOT_003 +bootfile=pImage +stdin=serial +stdout=serial +stderr=serial + +Environment size: 560/8188 bytes +MPC8560ADS=> fli + +Bank # 1: Intel 28F640J3A (64 Mbit, 64 x 128K) + Size: 16 MB in 64 Sectors + Sector Start Addresses: + FF000000 FF040000 FF080000 FF0C0000 FF100000 + FF140000 FF180000 FF1C0000 FF200000 FF240000 + FF280000 FF2C0000 FF300000 FF340000 FF380000 + FF3C0000 FF400000 FF440000 FF480000 FF4C0000 + FF500000 FF540000 FF580000 FF5C0000 FF600000 + FF640000 FF680000 FF6C0000 FF700000 FF740000 + FF780000 FF7C0000 FF800000 FF840000 FF880000 + FF8C0000 FF900000 FF940000 FF980000 FF9C0000 + FFA00000 FFA40000 FFA80000 FFAC0000 FFB00000 + FFB40000 FFB80000 FFBC0000 FFC00000 FFC40000 + FFC80000 FFCC0000 FFD00000 FFD40000 FFD80000 + FFDC0000 FFE00000 FFE40000 FFE80000 FFEC0000 + FFF00000 FFF40000 FFF80000 (RO) FFFC0000 (RO) +MPC8560ADS=> imi ff100000 + +## Checking Image at ff100000 ... + Image Name: Linux-2.4.21-rc5 + Image Type: PowerPC Linux Kernel Image (gzip compressed) + Data Size: 755361 Bytes = 737.7 kB + Load Address: 00000000 + Entry Point: 00000000 + Verifying Checksum ... OK +MPC8560ADS=> tftp 1000000 pImage.dracom.public +TFTP from server 163.12.64.52; our IP address is 10.82.0.105; sending through gateway 10.82.1.254 +Filename 'pImage.dracom.public'. +Load address: 0x1000000 +Loading: *################################################################# + ################################################################# + ################## +done +Bytes transferred = 755425 (b86e1 hex) +MPC8560ADS=> bootm ff100000 +## Booting image at ff100000 ... + Image Name: Linux-2.4.21-rc5 + Image Type: PowerPC Linux Kernel Image (gzip compressed) + Data Size: 755361 Bytes = 737.7 kB + Load Address: 00000000 + Entry Point: 00000000 + Verifying Checksum ... OK + Uncompressing Kernel Image ... OK +mpc85xx_init(): exit +id mach(): done +MMU:enter +Memory CAM mapping: CAM0=64Mb, CAM1=64Mb, CAM2=0Mb residual: 0Mb +MMU:hw init +MMU:mapin +MMU:mapin_ram done +MMU:setio +MMU:exit +Linux version 2.4.21-rc5 (@etest) (gcc version 2.95.3 20010315 (release)) #2 Wed Oct 15 09:13:46 CDT 2003 +setup_arch: enter +setup_arch: bootmem +mpc85xx_setup_arch +Host Bridge Vendor ID = 1057 +Host Bridge Device ID = 3 +Host Bridge header = 0 +arch: exit +On node 0 totalpages: 32768 +zone(0): 32768 pages. +zone(1): 0 pages. +zone(2): 0 pages. +Kernel command line: root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8560ads-003:eth0:off console=ttyS0,115200 +openpic: enter +OpenPIC Version 1.2 (1 CPUs and 44 IRQ sources) at fdf40000 +openpic: timer +openpic: external +openpic: spurious +openpic: exit +time_init: decrementer frequency = 33.000000 MHz +Calibrating delay loop... 226.09 BogoMIPS +Memory: 127624k available (1276k kernel code, 384k data, 236k init, 0k highmem) +Dentry cache hash table entries: 16384 (order: 5, 131072 bytes) +Inode cache hash table entries: 8192 (order: 4, 65536 bytes) +Mount cache hash table entries: 512 (order: 0, 4096 bytes) +Buffer-cache hash table entries: 8192 (order: 3, 32768 bytes) +Page-cache hash table entries: 32768 (order: 5, 131072 bytes) +POSIX conformance testing by UNIFIX +PCI: Probing PCI hardware + +Linux NET4.0 for Linux 2.4 +Based upon Swansea University Computer Society NET3.039 +Initializing RT netlink socket +Starting kswapd +Installing knfsd (copyright (C) 1996 okir@monad.swb.de). +CPM UART driver version 0.01 +ttyS0 on SCC1 at 0x8000, BRG1 +UART interrupt installed(40) +pty: 256 Unix98 ptys configured +eth0: Three Speed Ethernet Controller Version 0.2, 00:01:af:07:9b:8a: +eth1: Three Speed Ethernet Controller Version 0.2, 00:01:af:07:9b:8b: +RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize +loop: loaded (max 8 devices) +Intel(R) PRO/1000 Network Driver - version 5.0.43-k1 +Copyright (c) 1999-2003 Intel Corporation. +PPP generic driver version 2.4.2 +PPP Deflate Compression module registered +NET4: Linux TCP/IP 1.0 for NET4.0 +IP Protocols: ICMP, UDP, TCP, IGMP +IP: routing cache hash table of 1024 buckets, 8Kbytes +TCP: Hash tables configured (established 8192 bind 8192) +IP-Config: Complete: + device=eth0, addr=10.82.0.105, mask=255.255.254.0, gw=10.82.1.254, + host=mpc8560ads-003, domain=, nis-domain=(none), + bootserver=163.12.64.52, rootserver=163.12.64.52, rootpath= +NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. +Looking up port of RPC 100003/2 on 163.12.64.52 +Looking up port of RPC 100005/1 on 163.12.64.52 +VFS: Mounted root (nfs filesystem). +Freeing unused kernel memory: 236k init +INIT: version 2.78 booting +Activating swap... +Checking all file systems... +Parallelizing fsck version 1.22 (22-Jun-2001) +Mounting local filesystems... +nothing was mounted +Cleaning: /etc/network/ifstate. +Setting up IP spoofing protection: FAILED +Configuring network interfaces: done. +Starting portmap daemon: portmap. +Cleaning: /tmp /var/lock /var/run. +INIT: Entering runlevel: 2 +Starting system log daemon: syslogd klogd. +Starting internet superserver: inetd. + +mpc8560ads-003 login: root +Last login: Thu Jan 1 00:00:05 1970 on console +Linux mpc8560ads-003 2.4.21-rc5 #2 Wed Oct 15 09:13:46 CDT 2003 ppc unknown + +root@mpc8560ads-003:~# ls +21142.o aa e100.o hello.o mii.o timer.o +root@mpc8560ads-003:~# cd / +root@mpc8560ads-003:/# ls +bin boot dev etc home lib mnt opt proc root sbin tmp usr var +root@mpc8560ads-003:/# /sbin/ifconfig +eth0 Link encap:Ethernet HWaddr 00:01:AF:07:9B:8A + inet addr:10.82.0.105 Bcast:10.82.1.255 Mask:255.255.254.0 + UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 + RX packets:4608 errors:0 dropped:0 overruns:0 frame:0 + TX packets:2610 errors:0 dropped:0 overruns:0 carrier:0 + collisions:0 txqueuelen:100 + RX bytes:4465943 (4.2 Mb) TX bytes:440944 (430.6 Kb) + Base address:0x4000 + +lo Link encap:Local Loopback + inet addr:127.0.0.1 Mask:255.0.0.0 + UP LOOPBACK RUNNING MTU:16436 Metric:1 + RX packets:4 errors:0 dropped:0 overruns:0 frame:0 + TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 + collisions:0 txqueuelen:0 + RX bytes:296 (296.0 b) TX bytes:296 (296.0 b) + +root@mpc8560ads-003:/# ping 163.12.64.52 +PING 163.12.64.52 (163.12.64.52): 56 data bytes +64 bytes from 163.12.64.52: icmp_seq=0 ttl=63 time=0.1 ms +64 bytes from 163.12.64.52: icmp_seq=1 ttl=63 time=0.1 ms +64 bytes from 163.12.64.52: icmp_seq=2 ttl=63 time=0.1 ms + +--- 163.12.64.52 ping statistics --- +3 packets transmitted, 3 packets received, 0% packet loss +round-trip min/avg/max = 0.1/0.1/0.1 ms +root@mpc8560ads-003:/# diff --git a/doc/README.nios b/doc/README.nios index 2cee723..d7e87d5 100644 --- a/doc/README.nios +++ b/doc/README.nios @@ -44,7 +44,6 @@ The Nios port also does not use the long-winded peripheral structure definitions from the Nios SDK. - 2. CONFIGURATION OPTIONS/SETTINGS ---------------------------------- @@ -189,7 +188,6 @@ for those interested in contributing: MSTEP and MUL instructions (e.g. CFG_NIOS_MULT_HW and CFG_NIOS_MULT_MSTEP). - Regards, --Scott |