diff options
Diffstat (limited to 'doc')
| -rw-r--r-- | doc/README.bamboo | 62 | ||||
| -rw-r--r-- | doc/README.generic_usb_ohci | 5 | ||||
| -rw-r--r-- | doc/README.m5253evbe | 103 | ||||
| -rw-r--r-- | doc/README.m54455evb | 416 | ||||
| -rw-r--r-- | doc/README.mpc8544ds | 122 | ||||
| -rw-r--r-- | doc/README.sbc8641d | 28 | ||||
| -rw-r--r-- | doc/README.zeus | 73 |
7 files changed, 805 insertions, 4 deletions
diff --git a/doc/README.bamboo b/doc/README.bamboo index b50be01..e139c6d 100644 --- a/doc/README.bamboo +++ b/doc/README.bamboo @@ -1,3 +1,65 @@ +The 2 important dipswitches are configured as shown below: + +SW1 (for 33MHz SysClk) +---------------------- +S1 S2 S3 S4 S5 S6 S7 S8 +OFF OFF OFF OFF OFF OFF OFF ON + +SW7 (for Op-Code Flash and Boot Option H) +----------------------------------------- +S1 S2 S3 S4 S5 S6 S7 S8 +OFF OFF OFF ON OFF OFF OFF OFF + +The EEPROM at location 0x52 is loaded with these 16 bytes: +C47042A6 05D7A190 40082350 0d050000 + +SDR0_SDSTP0[ENG]: 1 : PLL's VCO is the source for PLL forward divisors +SDR0_SDSTP0[SRC]: 1 : Feedback originates from PLLOUTB +SDR0_SDSTP0[SEL]: 0 : Feedback selection is PLL output +SDR0_SDSTP0[TUNE]: 1000111000 : 10 <= M <= 22, 600MHz < VCO <= 900MHz +SDR0_SDSTP0[FBDV]: 4 : PLL feedback divisor +SDR0_SDSTP0[FBDVA]: 2 : PLL forward divisor A +SDR0_SDSTP0[FBDVB]: 5 : PLL forward divisor B +SDR0_SDSTP0[PRBDV0]: 1 : PLL primary divisor B +SDR0_SDSTP0[OPBDV0]: 2 : OPB clock divisor +SDR0_SDSTP0[LFBDV]: 1 : PLL local feedback divisor +SDR0_SDSTP0[PERDV0]: 3 : Peripheral clock divisor 0 +SDR0_SDSTP0[MALDV0]: 2 : MAL clock divisor 0 +SDR0_SDSTP0[PCIDV0]: 2 : Sync PCI clock divisor 0 +SDR0_SDSTP0[PLLTIMER]: 7 : PLL locking timer +SDR0_SDSTP0[RW]: 1 : EBC ROM width: 16-bit +SDR0_SDSTP0[RL]: 0 : EBC ROM location: EBC +SDR0_SDSTP0[PAE]: 0 : PCI internal arbiter: disabled +SDR0_SDSTP0[PHCE]: 0 : PCI host configuration: disabled +SDR0_SDSTP0[ZM]: 3 : ZMII mode: RMII mode 100 +SDR0_SDSTP0[CTE]: 0 : CPU trace: disabled +SDR0_SDSTP0[Nto1]: 0 : CPU/PLB ratio N/P: not N to 1 +SDR0_SDSTP0[PAME]: 1 : PCI asynchronous mode: enabled +SDR0_SDSTP0[MEM]: 1 : Multiplex: EMAC +SDR0_SDSTP0[NE]: 0 : NDFC: disabled +SDR0_SDSTP0[NBW]: 0 : NDFC boot width: 8-bit +SDR0_SDSTP0[NBW]: 0 : NDFC boot page selection +SDR0_SDSTP0[NBAC]: 0 : NDFC boot address selection cycle: 3 Addr. Cycles, 1 Col. + 2 Row (512 page size) +SDR0_SDSTP0[NARE]: 0 : NDFC auto read : disabled +SDR0_SDSTP0[NRB]: 0 : NDFC Ready/Busy : Ready +SDR0_SDSTP0[NDRSC]: 33333 : NDFC device reset counter +SDR0_SDSTP0[NCG0]: 0 : NDFC/EBC chip select gating CS0 : EBC +SDR0_SDSTP0[NCG1]: 0 : NDFC/EBC chip select gating CS1 : EBC +SDR0_SDSTP0[NCG2]: 0 : NDFC/EBC chip select gating CS2 : EBC +SDR0_SDSTP0[NCG3]: 0 : NDFC/EBC chip select gating CS3 : EBC +SDR0_SDSTP0[NCRDC]: 3333 : NDFC device read count + +PPC440EP Clocking Configuration + +SysClk is 33.0MHz, M is 20, VCO is 660.0MHz, CPU is 330.0MHz, PLB is 132.0MHz +OPB is 66.0MHz, EBC is 44.0MHz, MAL is 66.0MHz, Sync PCI is 66.0MHz + +The above information is reported by Eugene O'Brien +<Eugene.O'Brien@advantechamt.com>. Thanks a lot. + +2007-08-06, Stefan Roese <sr@denx.de> +--------------------------------------------------------------------- + The configuration for the AMCC 440EP eval board "Bamboo" was changed to only use 384 kbytes of FLASH for the U-Boot image. This way the redundant environment can be saved in the remaining 2 sectors of the diff --git a/doc/README.generic_usb_ohci b/doc/README.generic_usb_ohci index c343dfd..494dd1f 100644 --- a/doc/README.generic_usb_ohci +++ b/doc/README.generic_usb_ohci @@ -41,7 +41,7 @@ mpc5xxx. For these the config option CFG_OHCI_BE_CONTROLLER -needs to be defined. +needs to be defined. PCI Controllers @@ -55,6 +55,3 @@ PCI Controllers need to do byte swapping on register accesses, so they should to define: CFG_OHCI_SWAP_REG_ACCESS - - - diff --git a/doc/README.m5253evbe b/doc/README.m5253evbe new file mode 100644 index 0000000..0426cb1 --- /dev/null +++ b/doc/README.m5253evbe @@ -0,0 +1,103 @@ +Freescale Amadeus Plus M5253EVBE board +====================================== + +Hayden Fraser(Hayden.Fraser@freescale.com) +Created 06/05/2007 +=========================================== + + +1. SWITCH SETTINGS +================== +1.1 N/A + + +2. MEMORY MAP UNDER U-BOOT AND LINUX KERNEL +=========================================== +2.1. For the initial bringup, we adopted a consistent memory scheme between u-boot and + linux kernel, you can customize it based on your system requirements: + SDR: 0x00000000-0x00ffffff + SRAM0: 0x20010000-0x20017fff + SRAM1: 0x20000000-0x2000ffff + MBAR1: 0x10000000-0x4fffffff + MBAR2: 0x80000000-0xCfffffff + Flash: 0xffe00000-0xffffffff + +3. DEFINITIONS AND COMPILATION +============================== +3.1 Explanation on NEW definitions in include/configs/M5253EVBE.h + CONFIG_MCF52x2 Processor family + CONFIG_MCF5253 MCF5253 specific + CONFIG_M5253EVBE Amadeus Plus board specific + CFG_CLK Define Amadeus Plus CPU Clock + CFG_MBAR MBAR base address + CFG_MBAR2 MBAR2 base address + +3.2 Compilation + export CROSS_COMPILE=/usr/local/freescale-coldfire-4.1-elf/bin/m68k-elf- + cd u-boot-1-2-x + make distclean + make M5253EVBE_config + make + + +4. SCREEN DUMP +============== +4.1 U-Boot 1.2.0 (Jun 18 2007 - 18:20:00) + +CPU: Freescale Coldfire MCF5253 at 62 MHz +Board: Freescale MCF5253 EVBE +DRAM: 16 MB +FLASH: 2 MB +In: serial +Out: serial +Err: serial +=> flinfo + +Bank # 1: CFI conformant FLASH (16 x 16) Size: 2 MB in 35 Sectors + AMD Standard command set, Manufacturer ID: 0x01, Device ID: 0x49 + Erase timeout: 16384 ms, write timeout: 1 ms + + Sector Start Addresses: + FFE00000 RO FFE04000 RO FFE06000 RO FFE08000 RO FFE10000 RO + FFE20000 FFE30000 FFE40000 FFE50000 FFE60000 + FFE70000 FFE80000 FFE90000 FFEA0000 FFEB0000 + FFEC0000 FFED0000 FFEE0000 FFEF0000 FFF00000 + FFF10000 FFF20000 FFF30000 FFF40000 FFF50000 + FFF60000 FFF70000 FFF80000 FFF90000 FFFA0000 + FFFB0000 FFFC0000 FFFD0000 FFFE0000 FFFF0000 + +=> bdinfo +boot_params = 0x00F62F90 +memstart = 0x00000000 +memsize = 0x01000000 +flashstart = 0xFFE00000 +flashsize = 0x00200000 +flashoffset = 0x00000000 +baudrate = 19200 bps + +=> printenv +bootdelay=5 +baudrate=19200 +stdin=serial +stdout=serial +stderr=serial + +Environment size: 134/8188 bytes +=> saveenv +Saving Environment to Flash... +Un-Protected 1 sectors +Erasing Flash... +. done +Erased 1 sectors +Writing to Flash... done +Protected 1 sectors +=> + +5. COMPILER +----------- +To create U-Boot the CodeSourcery's version of the GNU Toolchain for the ColdFire architecture +compiler set (freescale-coldfire-4.1-elf) from www.codesourcery.com was used. +You can download it from:http://www.codesourcery.com/gnu_toolchains/coldfire/download.html + +compiler that you used - for example, codesourcery_elf requires -MQ in rules.mk, old M68K 2.95.3 just -M +codesourcery_elf requires -MQ in rules.mk, old M68K 2.95.3 just -M diff --git a/doc/README.m54455evb b/doc/README.m54455evb new file mode 100644 index 0000000..119a19d --- /dev/null +++ b/doc/README.m54455evb @@ -0,0 +1,416 @@ +Freescale MCF54455EVB ColdFire Development Board +================================================ + +TsiChung Liew(Tsi-Chung.Liew@freescale.com) +Created 4/08/07 +=========================================== + + +Changed files: +============== + +- board/freescale/m54455evb/m54455evb.c Dram setup, IDE pre init, and PCI init +- board/freescale/m54455evb/flash.c Atmel and INTEL flash support +- board/freescale/m54455evb/Makefile Makefile +- board/freescale/m54455evb/config.mk config make +- board/freescale/m54455evb/u-boot.lds Linker description + +- common/cmd_bdinfo.c Clock frequencies output +- common/cmd_mii.c mii support + +- cpu/mcf5445x/cpu.c cpu specific code +- cpu/mcf5445x/cpu_init.c Flexbus ChipSelect, Mux pins setup, icache and RTC extra regs +- cpu/mcf5445x/interrupts.c cpu specific interrupt support +- cpu/mcf5445x/speed.c system, pci, flexbus, and cpu clock +- cpu/mcf5445x/Makefile Makefile +- cpu/mcf5445x/config.mk config make +- cpu/mcf5445x/start.S start up assembly code + +- doc/README.m54455evb This readme file + +- drivers/net/mcffec.c ColdFire common FEC driver +- drivers/serial/mcfuart.c ColdFire common UART driver + +- include/asm-m68k/bitops.h Bit operation function export +- include/asm-m68k/byteorder.h Byte order functions +- include/asm-m68k/fec.h FEC structure and definition +- include/asm-m68k/fsl_i2c.h I2C structure and definition +- include/asm-m68k/global_data.h Global data structure +- include/asm-m68k/immap.h ColdFire specific header file and driver macros +- include/asm-m68k/immap_5445x.h mcf5445x specific header file +- include/asm-m68k/io.h io functions +- include/asm-m68k/m5445x.h mcf5445x specific header file +- include/asm-m68k/posix_types.h Posix +- include/asm-m68k/processor.h header file +- include/asm-m68k/ptrace.h Exception structure +- include/asm-m68k/rtc.h Realtime clock header file +- include/asm-m68k/string.h String function export +- include/asm-m68k/timer.h Timer structure and definition +- include/asm-m68k/types.h Data types definition +- include/asm-m68k/uart.h Uart structure and definition +- include/asm-m68k/u-boot.h u-boot structure + +- include/configs/M54455EVB.h Board specific configuration file + +- lib_m68k/board.c board init function +- lib_m68k/cache.c +- lib_m68k/interrupts Coldfire common interrupt functions +- lib_m68k/m68k_linux.c +- lib_m68k/time.c Timer functions (Dma timer and PIT) +- lib_m68k/traps.c Exception init code + +- rtc/mcfrtc.c Realtime clock Driver + +1 MCF5445x specific Options/Settings +==================================== +1.1 pre-loader is no longer suppoer in thie coldfire family + +1.2 Configuration settings for M54455EVB Development Board +CONFIG_MCF5445x -- define for all MCF5445x CPUs +CONFIG_M54455 -- define for all Freescale MCF54455 CPUs +CONFIG_M54455EVB -- define for M54455EVB board + +CONFIG_MCFUART -- define to use common CF Uart driver +CFG_UART_PORT -- define UART port number, start with 0, 1 and 2 +CONFIG_BAUDRATE -- define UART baudrate + +CONFIG_MCFRTC -- define to use common CF RTC driver +CFG_MCFRTC_BASE -- provide base address for RTC in immap.h +CFG_RTC_OSCILLATOR -- define RTC clock frequency +RTC_DEBUG -- define to show RTC debug message +CONFIG_CMD_DATE -- enable to use date feature in u-boot + +CONFIG_MCFFEC -- define to use common CF FEC driver +CONFIG_NET_MULTI -- define to use multi FEC in u-boot +CONFIG_MII -- enable to use MII driver +CONFIG_CF_DOMII -- enable to use MII feature in cmd_mii.c +CFG_DISCOVER_PHY -- enable PHY discovery +CFG_RX_ETH_BUFFER -- Set FEC Receive buffer +CFG_FAULT_ECHO_LINK_DOWN-- +CFG_FEC0_PINMUX -- Set FEC0 Pin configuration +CFG_FEC1_PINMUX -- Set FEC1 Pin configuration +CFG_FEC0_MIIBASE -- Set FEC0 MII base register +CFG_FEC1_MIIBASE -- Set FEC0 MII base register +MCFFEC_TOUT_LOOP -- set FEC timeout loop +CONFIG_HAS_ETH1 -- define to enable second FEC in u-boot + +CONFIG_ISO_PARTITION -- enable ISO read/write +CONFIG_DOS_PARTITION -- enable DOS read/write +CONFIG_IDE_RESET -- define ide_reset() +CONFIG_IDE_PREINIT -- define ide_preinit() +CONFIG_ATAPI -- define ATAPI support +CONFIG_LBA48 -- define LBA48 (larger than 120GB) support +CFG_IDE_MAXBUS -- define max channel +CFG_IDE_MAXDEVICE -- define max devices per channel +CFG_ATA_BASE_ADDR -- define ATA base address +CFG_ATA_IDE0_OFFSET -- define ATA IDE0 offset +CFG_ATA_DATA_OFFSET -- define ATA data IO +CFG_ATA_REG_OFFSET -- define for normal register accesses +CFG_ATA_ALT_OFFSET -- define for alternate registers +CFG_ATA_STRIDE -- define for Interval between registers +_IO_BASE -- define for IO base address + +CONFIG_MCFTMR -- define to use DMA timer +CONFIG_MCFPIT -- define to use PIT timer + +CONFIG_FSL_I2C -- define to use FSL common I2C driver +CONFIG_HARD_I2C -- define for I2C hardware support +CONFIG_SOFT_I2C -- define for I2C bit-banged +CFG_I2C_SPEED -- define for I2C speed +CFG_I2C_SLAVE -- define for I2C slave address +CFG_I2C_OFFSET -- define for I2C base address offset +CFG_IMMR -- define for MBAR offset + +CONFIG_PCI -- define for PCI support +CONFIG_PCI_PNP -- define for Plug n play support +CFG_PCI_MEM_BUS -- PCI memory logical offset +CFG_PCI_MEM_PHYS -- PCI memory physical offset +CFG_PCI_MEM_SIZE -- PCI memory size +CFG_PCI_IO_BUS -- PCI IO logical offset +CFG_PCI_IO_PHYS -- PCI IO physical offset +CFG_PCI_IO_SIZE -- PCI IO size +CFG_PCI_CFG_BUS -- PCI Configuration logical offset +CFG_PCI_CFG_PHYS -- PCI Configuration physical offset +CFG_PCI_CFG_SIZE -- PCI Configuration size + +CONFIG_EXTRA_CLOCK -- Enable extra clock such as vco, flexbus, pci, etc + +CFG_MBAR -- define MBAR offset + +CFG_ATMEL_BOOT -- To determine the u-boot is booted from Atmel or Intel + +CONFIG_MONITOR_IS_IN_RAM -- Not support + +CFG_INIT_RAM_ADDR -- defines the base address of the MCF54455 internal SRAM + +CFG_CSn_BASE -- defines the Chip Select Base register +CFG_CSn_MASK -- defines the Chip Select Mask register +CFG_CSn_CTRL -- defines the Chip Select Control register + +CFG_ATMEL_BASE -- defines the Atmel Flash base +CFG_INTEL_BASE -- defines the Intel Flash base + +CFG_SDRAM_BASE -- defines the DRAM Base +CFG_SDRAM_BASE1 -- defines the DRAM Base 1 + +2. MEMORY MAP UNDER U-BOOT AND LINUX KERNEL +=========================================== +2.1. System memory map: + Flash: 0x00000000-0x3FFFFFFF (1024MB) + DDR: 0x40000000-0x7FFFFFFF (1024MB) + SRAM: 0x80000000-0x8FFFFFFF (256MB) + ATA: 0x90000000-0x9FFFFFFF (256MB) + PCI: 0xA0000000-0xBFFFFFFF (512MB) + FlexBus: 0xC0000000-0xDFFFFFFF (512MB) + IP: 0xF0000000-0xFFFFFFFF (256MB) + +2.2. For the initial bringup, we adopted a consistent memory scheme between u-boot and + linux kernel, you can customize it based on your system requirements: + Atmel boot: + Flash0: 0x00000000-0x0007FFFF (512KB) + Flash1: 0x04000000-0x05FFFFFF (32MB) + Intel boot: + Flash0: 0x00000000-0x01FFFFFF (32MB) + Flash1: 0x04000000-0x0407FFFF (512KB) + + CPLD: 0x08000000-0x08FFFFFF (16MB) + FPGA: 0x09000000-0x09FFFFFF (16MB) + DDR: 0x40000000-0x4FFFFFFF (256MB) + SRAM: 0x80000000-0x80007FFF (32KB) + IP: 0xFC000000-0xFC0FFFFF (64KB) + +3. SWITCH SETTINGS +================== +3.1 SW1 Pin3: 0 - Boot from Atmel or 1 - INTEL + SW1 Pin4: 0 - ULPI chip not in reset state or 1 - ULPI chip in reset state + SW1 Pin5: 0 - Full ATA Bus enabled, FEC Phy1 powered down + 1 - Upper 8 bits ATA data bus disabled, FEC PHY1 active + SW1 Pin6: 0 - FEC Phy0 active or 1 - FEC Phy0 powered down + SW1 Pin3: 0 - Boot from Atmel or 1 - INTEL + +4. COMPILATION +============== +4.1 To create U-Boot the gcc-4.1-32 compiler set (ColdFire ELF version) +from codesourcery.com was used. Download it from: +http://www.codesourcery.com/gnu_toolchains/coldfire/download.html + +4.2 Compilation + export CROSS_COMPILE=cross-compile-prefix + cd u-boot-1.x.x + make distclean + make M54455EVB_config, or - default to atmel 33Mhz input clock + make M54455EVB_atmel_config, or - default to atmel 33Mhz input clock + make M54455EVB_a33_config, or - default to atmel 33Mhz input clock + make M54455EVB_a66_config, or - default to atmel 66Mhz input clock + make M54455EVB_intel_config, or - default to intel 33Mhz input clock + make M54455EVB_i33_config, or - default to intel 33Mhz input clock + make M54455EVB_i66_config, or - default to intel 66Mhz input clock + make + +5. SCREEN DUMP +============== +5.1 M54455EVB Development board + Boot from Atmel (NOTE: May not show exactly the same) + +U-Boot 1.2.0-g98c80b46-dirty (Jul 26 2007 - 12:44:08) + +CPU: Freescale MCF54455 (Mask:48 Version:1) + CPU CLK 266 Mhz BUS CLK 133 Mhz FLB CLK 66 Mhz + PCI CLK 33 Mhz INP CLK 33 Mhz VCO CLK 533 Mhz +Board: Freescale M54455 EVB +I2C: ready +DRAM: 256 MB +FLASH: 16.5 MB +In: serial +Out: serial +Err: serial +Net: FEC0, FEC1 +IDE: Bus 0: not available +-> print +bootargs=root=/dev/ram rw +bootdelay=1 +baudrate=115200 +ethaddr=00:e0:0c:bc:e5:60 +eth1addr=00:e0:0c:bc:e5:61 +hostname=M54455EVB +netdev=eth0 +inpclk=33333333 +loadaddr=40010000 +load=tftp ${loadaddr) ${u-boot} +upd=run load; run prog +prog=prot off 0 2ffff;era 0 2ffff;cp.b ${loadaddr} 0 ${filesize};save +ethact=FEC0 +mtdids=nor0=M54455EVB-1 +mtdparts=M54455EVB-1:16m(user) +u-boot=u-boot54455.bin +filesize=292b4 +fileaddr=40010000 +gatewayip=192.168.1.1 +netmask=255.255.255.0 +ipaddr=192.168.1.3 +serverip=192.168.1.2 +stdin=serial +stdout=serial +stderr=serial +mem=261632k + +Environment size: 563/8188 bytes +-> bdinfo +memstart = 0x40000000 +memsize = 0x10000000 +flashstart = 0x00000000 +flashsize = 0x01080000 +flashoffset = 0x00000000 +sramstart = 0x80000000 +sramsize = 0x00008000 +mbar = 0xFC000000 +busfreq = 133.333 MHz +pcifreq = 33.333 MHz +flbfreq = 66.666 MHz +inpfreq = 33.333 MHz +vcofreq = 533.333 MHz +ethaddr = 00:E0:0C:BC:E5:60 +eth1addr = 00:E0:0C:BC:E5:61 +ip_addr = 192.168.1.3 +baudrate = 115200 bps +-> +-> help +? - alias for 'help' +autoscr - run script from memory +base - print or set address offset +bdinfo - print Board Info structure +boot - boot default, i.e., run 'bootcmd' +bootd - boot default, i.e., run 'bootcmd' +bootelf - Boot from an ELF image in memory +bootm - boot application image from memory +bootp - boot image via network using BootP/TFTP protocol +bootvx - Boot vxWorks from an ELF image +cmp - memory compare +coninfo - print console devices and information +cp - memory copy +crc32 - checksum calculation +date - get/set/reset date & time +dcache - enable or disable data cache +diskboot- boot from IDE device +echo - echo args to console +erase - erase FLASH memory +ext2load- load binary file from a Ext2 filesystem +ext2ls - list files in a directory (default /) +fatinfo - print information about filesystem +fatload - load binary file from a dos filesystem +fatls - list files in a directory (default /) +flinfo - print FLASH memory information +fsinfo - print information about filesystems +fsload - load binary file from a filesystem image +go - start application at address 'addr' +help - print online help +icache - enable or disable instruction cache +icrc32 - checksum calculation +ide - IDE sub-system +iloop - infinite loop on address range +imd - i2c memory display +iminfo - print header information for application image +imls - list all images found in flash +imm - i2c memory modify (auto-incrementing) +imw - memory write (fill) +inm - memory modify (constant address) +iprobe - probe to discover valid I2C chip addresses +itest - return true/false on integer compare +loadb - load binary file over serial line (kermit mode) +loads - load S-Record file over serial line +loady - load binary file over serial line (ymodem mode) +loop - infinite loop on address range +ls - list files in a directory (default /) +md - memory display +mii - MII utility commands +mm - memory modify (auto-incrementing) +mtest - simple RAM test +mw - memory write (fill) +nfs - boot image via network using NFS protocol +nm - memory modify (constant address) +pci - list and access PCI Configuration Space +ping - send ICMP ECHO_REQUEST to network host +printenv- print environment variables +protect - enable or disable FLASH write protection +rarpboot- boot image via network using RARP/TFTP protocol +reset - Perform RESET of the CPU +run - run commands in an environment variable +saveenv - save environment variables to persistent storage +setenv - set environment variables +sleep - delay execution for some time +tftpboot- boot image via network using TFTP protocol +version - print monitor version +->bootm 4000000 + +## Booting image at 04000000 ... + Image Name: Linux Kernel Image + Created: 2007-08-14 15:13:00 UTC + Image Type: M68K Linux Kernel Image (uncompressed) + Data Size: 2301952 Bytes = 2.2 MB + Load Address: 40020000 + Entry Point: 40020000 + Verifying Checksum ... OK +OK +Linux version 2.6.20-gfe5136d6-dirty (mattw@kea) (gcc version 4.2.0 20070318 (pr +erelease) (Sourcery G++ Lite 4.2-20)) #108 Mon Aug 13 13:00:13 MDT 2007 +starting up linux startmem 0xc0254000, endmem 0xcfffffff, size 253MB +Built 1 zonelists. Total pages: 32624 +Kernel command line: root=/dev/mtdblock1 rw rootfstype=jffs2 ip=none mtdparts=ph +ysmap-flash.0:5M(kernel)ro,-(jffs2) +PID hash table entries: 1024 (order: 10, 4096 bytes) +Console: colour dummy device 80x25 +Dentry cache hash table entries: 32768 (order: 4, 131072 bytes) +Inode-cache hash table entries: 16384 (order: 3, 65536 bytes) +Memory: 257496k/262136k available (1864k kernel code, 2440k data, 88k init) +Mount-cache hash table entries: 1024 +NET: Registered protocol family 16 +SCSI subsystem initialized +NET: Registered protocol family 2 +IP route cache hash table entries: 2048 (order: 0, 8192 bytes) +TCP established hash table entries: 8192 (order: 2, 32768 bytes) +TCP bind hash table entries: 4096 (order: 1, 16384 bytes) +TCP: Hash tables configured (established 8192 bind 4096) +TCP reno registered +JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc. +io scheduler noop registered +io scheduler anticipatory registered +io scheduler deadline registered +io scheduler cfq registered (default) +ColdFire internal UART serial driver version 1.00 +ttyS0 at 0xfc060000 (irq = 90) is a builtin ColdFire UART +ttyS1 at 0xfc064000 (irq = 91) is a builtin ColdFire UART +ttyS2 at 0xfc068000 (irq = 92) is a builtin ColdFire UART +RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize +loop: loaded (max 8 devices) +FEC ENET Version 0.2 +fec: PHY @ 0x0, ID 0x20005ca2 -- DP83849 +eth0: ethernet 00:08:ee:00:e4:19 +physmap platform flash device: 01000000 at 04000000 +physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank + Intel/Sharp Extended Query Table at 0x0031 +Using buffer write method +cfi_cmdset_0001: Erase suspend on write enabled +2 cmdlinepart partitions found on MTD device physmap-flash.0 +Creating 2 MTD partitions on "physmap-flash.0": +0x00000000-0x00500000 : "kernel" +mtd: Giving out device 0 to kernel +0x00500000-0x01000000 : "jffs2" +mtd: Giving out device 1 to jffs2 +mice: PS/2 mouse device common for all mice +i2c /dev entries driver +TCP cubic registered +NET: Registered protocol family 1 +NET: Registered protocol family 17 +NET: Registered protocol family 15 +VFS: Mounted root (jffs2 filesystem). +Setting the hostname to freescale +Mounting filesystems +mount: Mounting usbfs on /proc/bus/usb failed: No such file or directory +Starting syslogd and klogd +Setting up networking on loopback device: +Setting up networking on eth0: +eth0: config: auto-negotiation on, 100FDX, 100HDX, 10FDX, 10HDX. +Adding static route for default gateway to 172.27.255.254: +Setting nameserver to 172.27.0.1 in /etc/resolv.conf: +Starting inetd: +/ # diff --git a/doc/README.mpc8544ds b/doc/README.mpc8544ds new file mode 100644 index 0000000..bf257a0 --- /dev/null +++ b/doc/README.mpc8544ds @@ -0,0 +1,122 @@ +Overview +-------- +The MPC8544DS system is similar to the 85xx CDS systems such +as the MPC8548CDS due to the similar E500 core. However, it +is placed on the same board as the 8641 HPCN system. + + +Flash Banks +----------- +Like the 85xx CDS systems, the 8544 DS board has two flash banks. +They are both present on boot, but there locations can be swapped +using the dip-switch SW10, bit 2. + +However, unlike the CDS systems, but similar to the 8641 HPCN +board, a runtime reset through the FPGA can also affect a swap +on the flash bank mappings for the next reset cycle. + +Irrespective of the switch SW10[2], booting is always from the +boot bank at 0xfff8_0000. + + +Memory Map +---------- + +0xff80_0000 - 0xffbf_ffff Alernate bank 4MB +0xffc0_0000 - 0xffff_ffff Boot bank 4MB + +0xffb8_0000 Alternate image start 512KB +0xfff8_0000 Boot image start 512KB + + +Flashing Images +--------------- + +For example, to place a new image in the alternate flash bank +and then reset with that new image temporarily, use this: + + tftp 1000000 u-boot.bin.8544ds + erase ffb80000 ffbfffff + cp.b 1000000 ffb80000 80000 + pixis_reset altbank + + +To overwrite the image in the boot flash bank: + + tftp 1000000 u-boot.bin.8544ds + protect off all + erase fff80000 ffffffff + cp.b 1000000 fff80000 80000 + +Other example U-Boot image and flash manipulations examples +can be found in the README.mpc85xxcds file as well. + + +The pixis_reset command +----------------------- +A new command, "pixis_reset", is introduced to reset mpc8641hpcn board +using the FPGA sequencer. When the board restarts, it has the option +of using either the current or alternate flash bank as the boot +image, with or without the watchdog timer enabled, and finally with +or without frequency changes. + +Usage is; + + pixis_reset + pixis_reset altbank + pixis_reset altbank wd + pixis_reset altbank cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio> + pixis_reset cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio> + +Examples; + + /* reset to current bank, like "reset" command */ + pixis_reset + + /* reset board but use the to alternate flash bank */ + pixis_reset altbank + + /* reset board, use alternate flash bank with watchdog timer enabled*/ + pixis_reset altbank wd + + /* reset board to alternate bank with frequency changed. + * 40 is SYSCLK, 2.5 is COREPLL ratio, 10 is MPXPLL ratio + */ + pixis-reset altbank cf 40 2.5 10 + +Valid clock choices are in the 8641 Reference Manuals. + + +Using the Device Tree Source File +--------------------------------- +To create the DTB (Device Tree Binary) image file, +use a command similar to this: + + dtc -b 0 -f -I dts -O dtb mpc8544ds.dts > mpc8544ds.dtb + +Likely, that .dts file will come from here; + + linux-2.6/arch/powerpc/boot/dts/mpc8544ds.dts + +After placing the DTB file in your TFTP disk area, +you can download that dtb file using a command like: + + tftp 900000 mpc8544ds.dtb + +Burn it to flash if you want. + + +Booting Linux +------------- + +Place a linux uImage in the TFTP disk area too. + + tftp 1000000 uImage.8544 + tftp 900000 mpc8544ds.dtb + bootm 1000000 - 900000 + +Watch your ethact, netdev and bootargs U-Boot environment variables. +You may want to do something like this too: + + setenv ethact eTSEC3 + setenv netdev eth1 diff --git a/doc/README.sbc8641d b/doc/README.sbc8641d new file mode 100644 index 0000000..a051466 --- /dev/null +++ b/doc/README.sbc8641d @@ -0,0 +1,28 @@ +Wind River SBC8641D reference board +=========================== + +Created 06/14/2007 Joe Hamman +Copyright 2007, Embedded Specialties, Inc. +Copyright 2007 Wind River Systemes, Inc. +----------------------------- + +1. Building U-Boot +------------------ +The SBC8641D code is known to build using ELDK 4.1. + + $ make sbc8641d_config + Configuring for sbc8641d board... + + $ make + + +2. Switch and Jumper Settings +----------------------------- +All Jumpers & Switches are in their default positions. Please refer to +the board documentation for details. Some settings control CPU voltages +and settings may change with board revisions. + +3. Known limitations +-------------------- +PCI: + The PCI command may hang if no boards are present in either slot. diff --git a/doc/README.zeus b/doc/README.zeus new file mode 100644 index 0000000..1848d8c --- /dev/null +++ b/doc/README.zeus @@ -0,0 +1,73 @@ + +Storage of the board specific values (ethaddr...) +------------------------------------------------- + +The board specific environment variables that should be unique +for each individual board, can be stored in the I2C EEPROM. This +will be done from offset 0x80 with the length of 0x80 bytes. The +following command can be used to store the values here: + +=> setdef de:20:6a:ed:e2:72 de:20:6a:ed:e2:73 AB0001 + + ethaddr eth1addr serial# + +Now those 3 values are stored into the I2C EEPROM. A CRC is added +to make sure that the values get not corrupted. + + +SW-Reset Pushbutton handling: +----------------------------- + +The SW-reset push button is connected to a GPIO input too. This +way U-Boot can "see" how long the SW-reset was pressed, and a +specific action can be taken. Two different actions are supported: + +a) Release after more than 5 seconds and less then 10 seconds: + -> Run POST + + Please note, that the POST test will take a while (approx. 1 min + on the 128MByte board). This is mainly due to the system memory + test. + +b) Release after more than 10 seconds: + -> Restore factory default settings + + The factory default values are restored. The default environment + variables are restored (ipaddr, serverip...) and the board + specific values (ethaddr, eth1addr and serial#) are restored + to the environment from the I2C EEPROM. Also a bootline parameter + is added to the Linux bootline to signal the Linux kernel upon + the next startup, that the factory defaults should be restored. + +The command to check this sw-reset status and act accordingly is + +=> chkreset + +This command is added to the default "bootcmd", so that it is called +automatically upon startup. + +Also, the 2 LED's are used to indicate the current status of this +command (time passed since pushing the button). When the POST test +will be run, the green LED will be switched off, and when the +factory restore will be initiated, the reg LED will be switched off. + + +Loggin of POST results: +----------------------- + +The results of the POST tests are logged in a logbuffer located at the end +of the onboard memory. It can be accessed with the U-Boot command "log": + +=> log show +<4>POST memory PASSED +<4>POST cache PASSED +<4>POST cpu PASSED +<4>POST uart PASSED +<4>POST ethernet PASSED + +The DENX Linux kernel tree has support for this log buffer included. Exactly +this buffer is used for logging of all kernel messages too. By enabling the +compile time option "CONFIG_LOGBUFFER" this support is enabled. This way you +can access the U-Boot log messages from Linux too. + +2007-08-10, Stefan Roese <sr@denx.de> |